Configurational Entropy Strategy Enhanced Structure Stability Achieves Robust Cathode for Aluminum Batteries.

Rechargeable aluminum batteries (RABs) are an emerging energy storage device owing to the vast Al resources, low cost, and high safety. However, the poor cyclability and inferior reversible capacity of cathode materials have limited the enhancement of RABs performance. Herein, a high configurational entropy strategy is presented to improve the electrochemical properties of RABs for the first time. The high-entropy (Fe, Mn, Ni, Zn, Mg)3 O4 cathode exhibits an ultra-stable cycling ability (109 mAh g-1 after 3000 cycles), high specific capacity (268 mAh g-1 at 0.5 A g-1 ), and rapid ion diffusion. Ex situ characterizations indicate that the operational mechanism of (Fe, Mn, Ni, Zn, Mg)3 O4 cathode is mainly based on the redox process of Fe, Mn, and Ni. Theoretical calculations demonstrate that the oxygen vacancies make a positive contribution to adjusting the distribution of electronic states, which is crucial for enhancing the reaction kinetics at the electrolyte and cathode interface. These findings not only propose a promising cathode material for RABs, but also provide the first elucidation of the operational mechanism and intrinsic information of high-entropy electrodes in multivalent ion batteries.

Elucidation of the Transport Properties of Calcium-Doped High Entropy Rare Earth Aluminates for Solid Oxide Fuel Cell Applications.

Solid oxide fuel cells (SOFCs) are paving the way to clean energy conversion, relying on efficient oxygen-ion conductors with high ionic conductivity coupled with a negligible electronic contribution. Doped rare earth aluminates are promising candidates for SOFC electrolytes due to their high ionic conductivity. However, they often suffer from p-type electronic conductivity at operating temperatures above 500 °C under oxidizing conditions caused by the incorporation of oxygen into the lattice. High entropy materials are a new class of materials conceptualized to be stable at higher temperatures due to their high configurational entropy. Introducing this concept to rare earth aluminates can be a promising approach to stabilize the lattice by shifting the stoichiometric point of the oxides to higher oxygen activities, and thereby, reducing the p-type electronic conductivity in the relevant oxygen partial pressure range. In this study, the high entropy oxide (Gd,La,Nd,Pr,Sm)AlO3 is synthesized and doped with Ca. The Ca-doped (Gd,La,Nd,Pr,Sm)AlO3 compounds exhibit a higher ionic conductivity than most of the corresponding Ca-doped rare earth aluminates accompanied by a reduction of the p-type electronic conductivity contribution typically observed under oxidizing conditions. In light of these findings, this study introduces high entropy aluminates as a promising candidate for SOFC electrolytes.

In Situ, Rapid Synthesis of Carbon-Loaded High Density and Ultrasmall High Entropy Oxide Nanoparticles as Efficient Electrocatalysts.

High entropy materials offer almost unlimited catalytic possibilities due to their variable composition, unique structure, and excellent electrocatalytic performance. However, due to the strong tendency of nanoparticles to coarsen and agglomerate, it is still a challenge to synthesize nanoparticles using simple methods to precisely control the morphology and size of the nanoparticles in large quantities, and their large-scale application is limited by high costs and low yields. Herein, a series of high-entropy oxides (HEOs) nanoparticles with high-density and ultrasmall size (<5 nm) loaded on carbon nanosheets with large quantities are prepared by Joule-heating treatment of gel precursors in a short period of time (≈60 s). Among them, the prepared (FeCoNiRuMn)3O4-x catalyst shows the best electrocatalytic activity for oxygen evolution reaction, with low overpotentials (230 mV @10 mA cm-2, 270 mV @100 mA cm-2), small Tafel slope (39.4 mV dec-1), and excellent stability without significant decay at 100 mA cm-2 after 100 h. The excellent performance of (FeCoNiRuMn)3O4-x can be attributed to the synergistic effect of multiple elements and the inherent structural stability of high entropy systems. This study provides a more comprehensive design idea for the preparation of efficient and stable high entropy catalysts.

A Density Functional Theory Analysis of Electrochemical Oxidation of Methane to Alcohol over High-Entropy Oxide (CoCrFeMnNi)3O4 Catalysts.

The direct conversion of methane into alcohol is a promising approach for achieving a low-carbon future, yet it remains a major challenge. In this study, we utilize density functional theory to explore the potential of the (CoCrFeMnNi)3O4 (CCFMNO) high entropy oxide (HEO) for electrochemical oxidation of methane to methanol and ethanol, alongside their competition with CO2 production. Our primary focus in this study is on thermodynamics, enabling a prompt analysis of the catalyst's potential, with the calculation of electrochemical barriers falling beyond our scope. Among all potential active sites within CCFMNO HEO, we identify Co as the most active site for methane activation when using carbonate ions as oxidants. This results in methanol production with a limiting potential of 1.4 VCHE, and ethanol and CO2 productions with a limiting potential of 1.2 VCHE. Additionally, our findings suggest that the occupied p-band center of O* on CCFMNO HEO is a potential descriptor for identifying the most active site within CCFMNO HEO. Overall, our results indicate that CCFMNO HEO holds promise as catalysts for methane oxidation to alcohols, employing carbonate ions as oxidants.

Sol-Gel-Derived Ordered Mesoporous High Entropy Spinel Ferrites and Assessment of Their Photoelectrochemical and Electrocatalytic Water Splitting Performance.

The novel material class of high entropy oxides with their unique and unexpected physicochemical properties is a candidate for energy applications. Herein, it is reported for the first time about the physico- and (photo-) electrochemical properties of ordered mesoporous (CoNiCuZnMg)Fe2 O4 thin films synthesized by a soft-templating and dip-coating approach. The A-site high entropy ferrites (HEF) are composed of periodically ordered mesopores building a highly accessible inorganic nanoarchitecture with large specific surface areas. The mesoporous spinel HEF thin films are found to be phase-pure and crack-free on the meso- and macroscale. The formation of the spinel structure hosting six distinct cations is verified by X-ray-based characterization techniques. Photoelectron spectroscopy gives insight into the chemical state of the implemented transition metals supporting the structural characterization data. Applied as photoanode for photoelectrochemical water splitting, the HEFs are photostable over several hours but show only low photoconductivity owing to fast surface recombination, as evidenced by intensity-modulated photocurrent spectroscopy. When applied as oxygen evolution reaction electrocatalyst, the HEF thin films possess overpotentials of 420 mV at 10 mA cm-2 in 1 m KOH. The results imply that the increase of the compositional disorder enhances the electronic transport properties, which are beneficial for both energy applications.

Architecting the High-Entropy Oxides on 2D MXene Nanosheets by Rapid Microwave-Heating Strategy with Robust Photoelectrochemical Oxygen Evolution Performance.

High-entropy oxides (HEO) have recently concerned interest as the most promising electrocatalytic materials for oxygen evolution reactions (OER). In this work, a new strategy to the synthesis of HEO nanostructures on Ti3 C2 Tx MXene via rapid microwave heating and subsequent calcination at a low temperature is reported. Furthermore, the influence of HEO loading on Ti3 C2 Tx MXene is investigated toward OER performance with and without visible-light illumination in an alkaline medium. The obtained HEO/Ti3 C2 Tx -0.5 hybrid exhibited an outstanding photoelectrochemical OER ability with a low overpotential of 331 mV at 10 mA cm-2 and a small Tafel slope of 71 mV dec-1 , which exceeded that of a commercial IrO2 catalyst (340 mV at 10 mA cm-2 ). In particular, the fabricated water electrolyzer with the HEO/Ti3 C2 Tx -0.5 hybrid as anode required a less potential of 1.62 V at 10 mA cm-2 under visible-light illumination. Owing to the strong synergistic interaction between the HEO and Ti3 C2 Tx MXene, the HEO/Ti3 C2 Tx hybrid has a great electrochemical surface area, many metal active sites, high conductivity, and fast reaction kinetics, resulting in an excellent OER performance. This study offers an efficient strategy for synthesizing HEO-based materials with high OER performance to produce high-value hydrogen fuel.

Physicochemical Properties of High-Entropy Oxides.

The development of industry has triggered an increasingly severe demand for new functional materials. In recent years, researches on high-entropy oxides (HEOs) are more comprehensive and in-depth, and their fascinating properties are gradually known to the public. The unique elemental synergistic effect and lattice distortion endow the high-entropy family with various untapped potential, and wide application fields and outstanding performance of HEOs make them candidates for future materials. In this review, the concept, structure, and synthesis of HEOs are firstly highlighted. Secondly, a variety of excellent properties and applications in the fields of mechanics, electrics, thermotics, optics and magnetics are summarized. This work provides a comprehensive overview about HEOs, facilitating the development of modern functionalities of the high-entropy family.

Eight-Component Nanoporous High-Entropy Oxides with Low Ru Contents as High-Performance Bifunctional Catalysts in Zn-Air Batteries.

One major challenge in heterogeneous catalysis is to reduce the usage of noble metals while maintaining the overall catalytic stability and efficiency in various chemical environments. In this work, a series of high-entropy catalysts are synthesized by a chemical dealloying method and find the increased entropy effect and non-noble metal contents would facilitate the formation of complete oxides with low crystallinity. Importantly, an optimal eight-component high-entropy oxide (HEO, Al-Ni-Co-Ru-Mo-Cr-Fe-Ti) is identified, which exhibits further enhanced catalytic activity for the oxygen evolution reaction (OER) as compared to the previously reported quinary AlNiCoRuMo and the widely-used commercial RuO2 catalysts, and at the same time similar catalytic activity for the oxygen reduction reaction (ORR) as the commercial Pt/C with a half-wave potential of 0.87 V. Such high-performance bi-functional catalysts, however, only require a half loading amount of Ru as compared to the quinary AlNiCoRuMo, due to the underlying Cr-Fe synergistic effects on tuning the electronic structures at active surface sites, as revealed by the first-principles density functional theory calculations of the authors. The eight-component HEO also demonstrates excellent stability under continuous electrochemical working conditions, suitable for a wide range of applications such as metal-air batteries.

Kinetically Accelerated Lithium Storage in High-Entropy (LiMgCoNiCuZn)O Enabled By Oxygen Vacancies.

High-entropy oxides (HEOs) are gradually becoming a new focus for lithium-ion battery (LIB) anodes due to their vast element space/adjustable electrochemical properties and unique single-phase retention ability. However, the sluggish kinetics upon long cycling limits their further generalization. Here, oxygen vacancies with targeted functionality are introduced into rock salt-type (MgCoNiCuZn)O through a wet-chemical molten salt strategy to accelerate the ion/electron transmission. Both experimental results and theoretical calculations reveal the potential improvement of lithium storage, charge transfer, and diffusion kinetics from HEO surface defects, which ultimately leads to enhanced electrochemical properties. The currently raised strategy offers a modular approach and enlightening insights for defect-induced HEO-based anodes.

Battery-Driven N2 Electrolysis Enabled by High-Entropy Catalysts: From Theoretical Prediction to Prototype Model.

A small-scale standalone device of nitrogen (N2 ) splitting holds great promise for producing ammonia (NH3 ) in a decentralized manner as the compensation or replacement of centralized Haber-Bosch process. However, the design of such a device has been impeded by sluggish kinetics of its half reactions, i.e., cathodic N2 reduction reaction (NRR) and anodic oxygen evolution reaction (OER). Here, it is predicted from density function theory that high-entropy oxides (HEOs) are potential catalysts for promoting NRR and OER, and subsequently develop a facile procedure to synthesize HEOs in the morphology of sea urchin-shaped hollow nanospheres assembled from ultrathin nanosheets. The excellent electrocatalytic activities of HEOs for both NRR (NH3 yield rate: 47.58 µg h-1 mg-1 and Faradaic efficiency (FE): 10.74%) and OER (215 mV @10 mA cm-2 ) are demonstrated. Consequently, a prototype device of N2 electrolysis driven by commercial batteries is constructed, which can operate smoothly and deliver remarkable NH3 yield rate (41.11 µg h-1 mg-1 ) and FE (14.14%). Further mechanism study has attributed the excellent catalytic performances of HEOs to their unique electronic structures originated from multi-metal synergistic effects and entropy increase effects. The work will provide new clues for designing versatile catalysts and devices for large-scale industrialization.

Persistent Structure and Frustrated Magnetism in High Entropy Rare-Earth Zirconates.

The configurational complexity and distinct local atomic environments of high entropy oxides remain largely unexplored, leaving structure-property relationships and the hypothesis that the family offers rich tunability for applications ambiguous. This work investigates the influence of cation size and materials synthesis in determining the resulting structure and magnetic properties of a family of high entropy rare-earth zirconates (HEREZs, nominal composition RE2 Zr2 O7 with RE = rare-earth element combinations including Eu, Gd, Tb, Dy, Ho, La, or Sc). The structural characterization of the series is examined through synchrotron X-ray diffraction and pair distribution function analysis, and electron microscopy, demonstrating average defect-fluorite structures with considerable local disorder, in all samples. The surface morphology and particle sizes are found to vary significantly with preparation method, with irregular micron-sized particles formed by high temperature sintering routes, spherical nanoparticles resulting from chemical co-precipitation methods, and porous nanoparticle agglomerates resulting from polymer steric entrapment synthesis. In agreement with the disordered cation distribution found across all samples, magnetic measurements indicate that all synthesized HEREZs show frustrated magnetic behavior, as seen in a number of single-component RE2 Zr2 O7 pyrochlore oxides. These findings advance the understanding of the local structure of high entropy oxides and demonstrate strategies for designing nanostructured morphologies in the class.

Useful High-Entropy Source on Spinel Oxides for Gas Detection.

This study aimed to identify a useful high-entropy source for gas detection by spinel oxides that are composed of five cations in nearly equal molar amounts and free of impurities. The sensor responses of the spinel oxides [1# (CoCrFeMnNi)3O4, 2# (CoCrFeMnZn)3O4, 3# (CoCrFeNiZn)3O4, 4# (CoCrMnNiZn)3O4, 5# (CoFeMnNiZn)3O4, and 6# (CrFeMnNiZn)3O4] were evaluated for the test gases (7 ppm NO2, 5000 ppm H2, 3 ppm NH3, and 3 ppm H2S). In response to NO2, 1# and 2# showed p-type behavior while 3-6# showed n-type semiconductor behavior. There are three p-type and one n-type AO structural compositions in AB2O4[AO·B2O3] type spinel, and 1# showed a stable AO composition because cation migration from site B to site A is unlikely. Therefore, it was assumed that 1# exhibited p-type behavior. The p-type behavior of 2# was influenced by Cr oxide ions that were present at the B site and the stable p-type behavior of zinc oxide at the A site. The spinel oxides 3# to 6# exhibited n-type behavior with the other cationic oxides rather than the dominant p-type behavior exhibited by the Zn oxide ions that are stable at the A site. In contrast, the sensor response to the reducing gases H2, NH3, and H2S showed p-type semiconductor behavior, with a particularly selective response to H2S. The sensor responses of the five-element spinel oxides in this study tended to be higher than that of the two-element Ni ferrites and three-element Ni-Zn ferrites reported previously. Additionally, the susceptibility to sulfurization was evaluated using the thermodynamic equilibrium theory for the AO and B2O3 compositions. The oxides of Cr, Fe, and Mn ions in the B2O3 composition did not respond to H2S because they were not sulfurized. The increase in the sensor response due to sulfurization was attributed to the decrease in the depletion layer owing to electron sensitization, as the top surface of the p-type semiconductors, ZnO and NiO, transformed to n-type semiconductors, ZnS and NiS, respectively. High-entropy oxides prepared using the hydrothermal method with an equimolar combination of five cations from six elements (Cr, Mn, Fe, Co, Ni, and Zn) can be used as a guideline for the design of high-sensitivity spinel-type composite oxide gas sensors.

Sol-Gel Synthesized High Entropy Metal Oxides as High-Performance Catalysts for Electrochemical Water Oxidation.

Hexanary high-entropy oxides (HEOs) were synthesized through the mechanochemical sol-gel method for electrocatalytic water oxidation reaction (WOR). As-synthesized catalysts were subjected to characterization, including X-ray diffraction (XRD), Fourier transforms infrared (FTIR) analysis, and scanning electron microscopy (SEM). All the oxide systems exhibited sharp diffraction peaks in XRD patterns indicating the defined crystal structure. Strong absorption between 400-700 cm-1 in FTIR indicated the formation of metal-oxide bonds in all HEO systems. WOR was investigated via cyclic voltammetry using HEOs as electrode platforms, 1M KOH as the basic medium, and 1M methanol (CH3OH) as the facilitator. Voltammetric profiles for both equiatomic (EHEOs) and non-equiatomic (NEHEOs) were investigated, and NEHEOs exhibited the maximum current output for WOR. Moreover, methanol addition improved the current profiles, thus leading to the electrode utility in direct methanol fuel cells as a sequential increase in methanol concentration from 1M to 2M enhanced the OER current density from 61.4 to 94.3 mA cm-2 using NEHEO. The NEHEOs comprising a greater percentage of Al, ([Al0.35(Mg, Fe, Cu, Ni, Co)0.65]3O4) displayed high WOR catalytic performance with the maximum diffusion coefficient, D° (10.90 cm2 s-1) and heterogeneous rate constant, k° (7.98 cm s-1) values. These primary findings from the EC processes for WOR provide the foundation for their applications in high-energy devices. Conclusively, HEOs are proven as novel and efficient catalytic platforms for electrochemical water oxidation.

Theoretical Optimization of Compositions of High-Entropy Oxides for the Oxygen Evolution Reaction.

High-entropy oxides are oxides consisting of five or more metals incorporated in a single lattice, and the large composition space suggests that properties of interest can be readily optimised. For applications within catalysis, the different local atomic environments result in a distribution of binding energies for the catalytic intermediates. Using the oxygen evolution reaction on the rutile (110) surface as example, here we outline a strategy for the theoretical optimization of the composition. Density functional theory calculations performed for a limited number of sites are used to fit a model that predicts the reaction energies for all possible local atomic environments. Two reaction pathways are considered; the conventional pathway on the coordinatively unsaturated sites and an alternative pathway involving transfer of protons to a bridging oxygen. An explicit model of the surface is constructed to describe the interdependency of the two pathways and identify the composition that maximizes catalytic activity.

Sol-Gel Synthesis of Ceria-Zirconia-Based High-Entropy Oxides as High-Promotion Catalysts for the Synthesis of 1,2-Diketones from Aldehyde.

Efficient Lewis-acid-catalyzed direct conversion of aldehydes to 1,2-diketones in the liquid phase was enabled by using newly designed and developed ceria-zirconia-based high-entropy oxides (HEOs) as the actual catalysts. The synergistic effect of various cations incorporated in the same oxide structure (framework) was partially responsible for the efficiency of multicationic materials compared to the corresponding single-cation oxide forms. Furthermore, a clear, linear relationship between the Lewis acidity and the catalytic activity of the HEOs was observed. Due to the developed strategy, exclusively diketone-selective, recyclable, versatile heterogeneous catalytic transformation of aldehydes can be realized under mild reaction conditions.

Defect-Rich High-Entropy Oxide Nanosheets for Efficient 5-Hydroxymethylfurfural Electrooxidation.

High-entropy oxides (HEOs), a new concept of entropy stabilization, exhibit unique structures and fascinating properties, and are thus important class of materials with significant technological potential. However, the conventional high-temperature synthesis techniques tend to afford micron-scale HEOs with low surface area, and the catalytic activity of available HEOs is still far from satisfactory because of their limited exposed active sites and poor intrinsic activity. Here we report a low-temperature plasma strategy for preparing defect-rich HEOs nanosheets with high surface area, and for the first time employ them for 5-hydroxymethylfurfural (HMF) electrooxidation. Owing to the nanosheets structure, abundant oxygen vacancies, and high surface area, the quinary (FeCrCoNiCu)3 O4 nanosheets deliver improved activity for HMF oxidation with lower onset potential and faster kinetics, outperforming that of HEOs prepared by high-temperature method. Our method opens new opportunities for synthesizing nanostructured HEOs with great potential applications.

Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1-x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ Ceramics.

Compositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multielement oxides with unexplored physical and functional properties. In this work, we report fluorite structure-derived compositionally complex zirconia with composition Zr1-x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides' structural, microstructural, mechanical, electrical, and electromechanical properties regarding phase separation and sintering mechanisms. Highly dense ceramics are achieved by bimodal mass diffusion, composing nanometric tetragonal and micrometric cubic grains microstructure. The material exhibits an anomalously large electrostriction response exceeding the M33 value of 10-17 m2/V2 at room temperature and viscoelastic properties of primary creep in nanoindentation measurement under fast loading. These findings are strikingly similar to those reported for doped ceria and bismuth oxide derivates, highlighting the presence of a large concentration of point defects linked to structural distortion and anelastic behavior, which are characteristics of nonclassical ionic electrostrictors.

Influence of entropy on catalytic performance of high-entropy oxides (NiMgZnCuCoOx) in peroxymonosulfate-mediated acetaminophen degradation.

Developing a high-performance activator is crucial for the practical application of peroxymonosulfate-based advanced oxidation processes (PMS-AOPs). High-entropy oxides (HEOs) have attracted increasing attention due to their stable crystal structure, flexible composition and unique functionality. However, research into the mechanisms by which HEOs function as PMS activators for degrading organic pollutants remains insufficient, and the relationship between entropy and the catalytic performance of HEOs has yet to be clarified. In this study, we synthesized NiMgZnCuCoOx with different levels of entropy as PMS activators for acetaminophen (APAP) degradation, and observed a significant effect for entropy on the catalytic performance. Sulfate radicals (SO4•‒) were identified as the primary reactive oxygen species (ROS), while hydroxyl radicals (•OH) and singlet oxygen (1O2) act as secondary ROS during APAP degradation. Both the Co2+ contents and the oxygen vacancy concentration in NiMgZnCuCoOx are found to increase with the entropy. An increase in the Co2+ sites leads to more activation sites for PMS activation, while excessive oxygen vacancies consume PMS, producing weak oxidation species, and affect the electron-donating ability of Co2+. Consequently, the NiMgZnCuCoOx with middle level of entropy exhibits the optimal performance with APAP degradation rate and mineralization rate reaching 100% and 74.22%, respectively. Furthermore, the degradation intermediates and their toxicities were assessed through liquid chromatography-mass spectrometry and quantitative structure-activity relationship analysis. This work is expected to provide critical insight into the impact of the HEOs entropy on the PMS activation and guide the rational design of highly efficient peroxymonosulfate activators for environmental applications.

High-Entropy Oxides for Rechargeable Batteries.

High-entropy oxides (HEOs) have garnered significant attention within the realm of rechargeable batteries owing to their distinctive advantages, which encompass diverse structural attributes, customizable compositions, entropy-driven stabilization effects, and remarkable superionic conductivity. Despite the brilliance of HEOs in energy conversion and storage applications, there is still lacking a comprehensive review for both entry-level and experienced researchers, which succinctly encapsulates the present status and the challenges inherent to HEOs, spanning structural features, intrinsic properties, prevalent synthetic methodologies, and diversified applications in rechargeable batteries. Within this review, the endeavor is to distill the structural characteristics, ionic conductivity, and entropy stabilization effects, explore the practical applications of HEOs in the realm of rechargeable batteries (lithium-ion, sodium-ion, and lithium-sulfur batteries), including anode and cathode materials, electrolytes, and electrocatalysts. The review seeks to furnish an overview of the evolving landscape of HEOs-based cell component materials, shedding light on the progress made and the hurdles encountered, as well as serving as the guidance for HEOs compositions design and optimization strategy to enhance the reversible structural stability, electrical properties, and electrochemical performance of rechargeable batteries in the realm of energy storage and conversion.

Localisation of vibrational modes in high-entropy oxides.

The recently-discovered high-entropy oxides (HEO's) offer a paradoxical combination of crystalline arrangement and high disorder. They differ qualitatively from established paradigms for disordered solids such as glasses and alloys. In these latter systems, it is well known that disorder induces localised vibrational excitations. In this article, we explore the possibility of disorder-induced localisation in Mg0.2Co0.2Ni0.2Cu0.2Zn0.2O, the prototypical HEO with rock-salt structure. To describe phononic excitations, we model the interatomic potentials for the cation-oxygen interactions by fitting to the physical properties of the parent binary oxides. We validate our model against the experimentally determined crystal structure and optical conductivity. The resulting phonon spectrum shows wave-like propagating modes at low energies and localised modes at high energies. Localisation is reflected in signatures such as participation ratio and correlation amplitude. Finally, we argue that mass disorder can be increased to enhance localisation. We consider a hypothetical material, high-entropy telluride-oxide, where tellurium atoms are admixed into the anion sublattice. This shows a larger localised fraction, with additional localised modes appearing in the middle of the spectrum. Our results demonstrate that HEO's are a promising platform to study Anderson localisation of phonons.