Microporous Electrode Binders for Anion Exchange Membrane Water Electrolyzers.

In anion exchange membrane (AEM) water electrolyzers, AEMs separate hydrogen and oxygen, but should efficiently transport hydroxide ions. In the electrodes, catalyst nanoparticles are mechanically bonded to the porous transport layer or membrane by a polymeric binder. Since these binders form a thin layer on the catalyst particles, they should not only transport hydroxide ions and water to the catalyst particles, but should also transport the nascating gases away. In the worst case, if formation of gases is >> than gas transport, a gas pocket between catalyst surface and the binder may form and hinder access to reactants (hydroxide ions, water). In this work, the ion conductive binder SEBS-DABCO is blended with PIM-1, a highly permeable polymer of intrinsic microporosity. With increasing amount of PIM-1 in the blends, the permeability for water (selected to represent small molecules) increases. Simultaneously, swelling and conductivity decrease, due to the increased hydrophobicity. Ex situ data and electrochemical data indicate that blends with 50% PIM-1 have better properties than blends with 25% or 75% PIM-1, and tests in the electrolyzer confirm an improved performance when the SEBS-DABCO binder contains 50% PIM-1.

Ionomeric Binders for High Temperature Proton Exchange Membrane Fuel Cells.

High-temperature proton exchange membrane fuel cell (HT-PEMFC) based on phosphoric acid doped polybenzimidazole membrane (PBI/PA) operating at 120-200 °C can provide insensitivity to carbon monoxide (CO) and simplified managements of water and heat and thus attract significant global attention. However, one significant drawback is its low utilization of precious metal catalysts resulted from the PA poisoning and inefficient three-phase boundary. Studies of binder materials in catalyst layers for HT-PEMFC are gradually emerging and there are few literature reviews on this important topic. The purpose of this review is to describe the various types of binders based on their molecular structure and electrochemical properties, with particular emphasis on catalyst layer for fuel cells. Importantly, this review provides a better understanding of relationship between fuel cell performance and the gas permeability and conductivity of different binders. Then, future directions of research and development in binder materials of HT-PEMFC are pointed out.

Bio-inspired synthesis of silver nanoparticles usingSalsola imbricataand its application as antibacterial additive in glass ionomer cement.

Nanotechnology has gained immense popularity and observed rapid development due to the remarkable physio-chemical properties of nanoparticles (NPs) and related nanomaterials. The green production of NPs has many benefits over traditional techniques because the current procedures are expensive, time-consuming, and involve harmful substances that limit their applicability. This study aimed to use a novel green source, theSalsola imbricata(SI) plant, which is commonly found in Central Asia and known for its medicinal properties as a reducing and stabilizing agent for the synthesis of AgNPs. The current study also utilized efficient statistical design, the Plackett-Burman Design (PBD) of Experiment method to synthesize the NPs. The characterization of NPs was carried out using UV-Vis spectroscopy, Fourier transform infrared spectroscopy, and scanning electron microscopy (SEM). The PBD results showed that only two out of four factorsi.e.AgNO3concentration and incubation time, were significant for the synthesis of SI-AgNPs. While remaining factors, incubation temperature and plant extract: AgNO3ratio were non-significant. The SEM analysis result showed that SI-AgNPs had a size of 20-50 nm. The SI-AgNPs demonstrated strong antibacterial activity against oral pathogens such asS. mutans and Lactobacillus acidophilus, with the highest efficacy observed at a concentration of 2 mg ml-1. The addition of SI-AgNPs in glass ionomer cement significantly increased the antibacterial activity of GIC againstS. mutans. Based on the results of the current study, the plant based AgNPs can be further evaluated in detail as alternate antimicrobial agent either alone or in combination with other antimicrobial agents for different dental applications.

Preventive and restorative alternatives to caries by irradiation: a scoping review.

PURPOSE: This study is to conduct a comprehensive scoping review to map scientific evidence and clarify concepts regarding the commonly recommended preventive and restorative dental treatments for patients diagnosed with head and neck cancer (HNC) and subjected to radiotherapy. MATERIAL AND METHODS: This systematic scoping review was performed under the PRISMA-ScR guidelines. The study's experimental design was registered in the Open Science Framework. In vitro studies that evaluated preventive and restorative dental treatment over 50 Gy radiation doses were included. The search was conducted in November 2023 in five electronic databases (PubMed, Scopus, Web of Science, Cochrane Library, and Embase) without language or date restriction. A search strategy was applied based on keywords, MeSh terms, or synonyms. A descriptive analysis was conducted. RESULTS: A total of 49 studies, out of 3679 original articles identified, were included and reviewed. Of the included studies, three evaluated saliva stimulants and 35 evaluated fluoride-based preventive materials: gel (n = 18) toothpaste (n = 11) mouth rinse (n = 8) and varnish (n = 5) while 14 evaluated restorative materials: resin composite (n = 12) glass ionomer cement (n = 6) and amalgam (n = 1) Of those studies, 36 were clinical trials and 13 were in vitro studies. CONCLUSION: Fluoride gel was the most frequently recommended preventive material for preventing radiation caries with supportive clinical evidence. Resin composite and glass ionomer were the most frequently used restorative materials, respectively. However, there is not yet clinical evidence to support the use of resin composite in irradiated teeth.

Preparation and in vivo and ex vivo studies of sirolimus nano-in-situ gel ophthalmic formulation.

Sirolimus (SR) is a macrolide with antifungal and antitumor immunosuppressant properties, classified as a selective inhibitor of mammalian target of rapamycin (mTOR). In this study, an ionic in situ gel of SR (SR-SUS-ISG) was formulated using gellan gum, exhibiting stability regardless of temperature and pH variations, causing minimal irritation. Harnessing the physiological conditions of the eye, SR-SUS-ISG underwent gelation upon contact with ions, increasing drug viscosity and prolonging retention on the ocular surface. Concurrently, SR-SUS-ISG displayed favorable shear dilution properties, reducing viscosity at ambient temperature, enhancing fluidity, and facilitating convenient packaging and transport. Biocompatibility assessments on both human corneal epithelial cells and rabbit eyes demonstrated that SR-SUS-ISG could well be tolerated. Pharmacokinetic investigations in rabbit ocular aqueous humor revealed sustained release, improved corneal penetration, and enhanced bioavailability. Additionally, in a rat corneal alkali burn model, SR-SUS-ISG exhibited inhibitory effects on corneal neovascularization, associated with decreased levels of the inflammatory factors VEGF and MMPs. These findings suggested that SR-SUS-ISG held promise as an effective ocular drug delivery system.

Antimicrobial effects of surface pre-reacted glass-ionomer (S-PRG) eluate against oral microcosm biofilm.

This study investigated the antimicrobial activity of surface pre-reacted glass ionomer eluate (S-PRG) against oral microcosm biofilms collected from the oral cavity of patients. Dental biofilm samples were collected from three volunteers to form microcosm biofilms in vitro. Initially, screening tests were carried out to determine the biofilm treatment conditions with S-PRG eluate. The effects of a daily treatment for 5 min using three microcosm biofilms from different patients was then evaluated. For this, biofilms were formed on tooth enamel specimens for 120 h. Biofilms treated with 100% S-PRG for 5 min per day for 5 days showed a reduction in the number of total microorganisms, streptococci and mutans streptococci. SEM images confirmed a reduction in the biofilm after treatment. Furthermore, S-PRG also reduced lactic acid production. It was concluded that S-PRG eluate reduced the microbial load and lactic acid production in oral microcosm biofilms, reinforcing its promising use as a mouthwash agent.

Long term results of glass ionomer ossiculoplasty.

OBJECTIVE: To analyze and compare the early and late post-operative results of glass ionomer bone cement (GIBC) used in ossiculoplasty. METHODS: The pre-operative, early post-operative (3 months) and late post-operative (> 2 years) audiometric findings, namely the pure-tone average (PTA), bone conduction threshold (BCT) and air-bone gap (ABG) of 40 patients who underwent GIBC ossiculoplasty for different etiologies were analyzed. Early and late results were compared. Also, the patients were grouped in terms of prognostic factors and applied ossiculoplasty techniques, and the results were compared between the groups. RESULTS: There were statistically significant improvements in the pure-tone average and air-bone gap of the patients in the early post-operative period (PTA from 59.60 ± 15.95 to 40.37 ± 17.83 and ABG from 37.12 ± 11.18 to 19.78 ± 10.41, p < 0.001 for both). There were no statistically significant changes in any of the audiometric parameters in the late post-operative period (PTA from 40.37 ± 17.83 to 39.79 ± 17.91, ABG from 19.78 ± 10.41 to 19.32 ± 9.60, BCT from 17.99 ± 12.71 to 18.31 ± 13.99, p > 0.05 for all). Presence of tympanosclerosis was found to be the only prognostic factor to affect the outcome. CONCLUSION: GIBC is a safe and reliable material for ossiculoplasty, which maintains its ability to conduct sound in the long-term follow-up.

Prevention of secondary caries using fluoride-loaded chitosan nanoparticle-modified glass-ionomer cement.

OBJECTIVE: To study the effect of incorporating chitosan and fluoride-loaded chitosan nanoparticles into a glass-ionomer cement (GIC) to prevent secondary caries. MATERIALS AND METHODS: A standard cervical cavity (mesio-distal width 6 mm, cervico-occlusal width 2 mm, and depth 2 mm) was prepared on 30 molars for the following restoration groups: group 1, conventional GIC restoration; group 2, chitosan (10%) modified GIC restoration; group 3, fluoride loaded chitosan nanoparticles (10%) modified GIC restoration. The restored teeth were subjected to 1,500 thermal cycles before undergoing a multi-species cariogenic biofilm challenge. The restored teeth were examined by micro-computed tomography (micro-CT), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX). Data were analyzed by the one-way ANOVA, Tukey HDS, Kruskal Wallis, and Dunn's test. RESULTS: Micro-CT determined outer lesion depths for groups 1-3 were: 614 ± 20 µm, 589 ± 17 µm, and 560 ± 19 µm respectively. Both modifications with chitosan and fluoride-loaded chitosan nanoparticles significantly affected outer lesion depth (p < 0.05). The modification with fluoride-loaded chitosan nanoparticles statistically significantly decreased the outer lesion depth compared to all other groups (p < 0.05). SEM/EDX showed an increase of calcium, phosphorus, and fluoride at the root dentine adjacent to the restoration in groups 2 and 3 (modified GIC). This increase was statistically significantly higher in the group modified with fluorine-loaded nano chitosan particles compared to the other groups (p < 0.05). CONCLUSION: Incorporation of 10% chitosan and 10% fluoride-loaded chitosan nanoparticles into GIC restorative material can prevent secondary root caries development. 10% fluoride-loaded chitosan nanoparticles were more effective. CLINICAL SIGNIFICANCE: Glass ionomer cement modified with fluoride-loaded chitosan nanoparticles may be a promising restorative material in pediatric and preventive dentistry due to their controlled release properties.

Effect of a calcium silicate cement and experimental glass ionomer cements containing calcium orthophosphate particles on demineralized dentin.

OBJECTIVE: The study aims to evaluate the effect of a glass ionomer cement (GIC; Fuji 9 Gold Label, GC) with added calcium orthophosphate particles and a calcium silicate cement (CSC; Biodentine, Septodont) regarding ion release, degradation in water, mineral content, and mechanical properties of demineralized dentin samples. METHODS: GIC, GIC + 5% DCPD (dicalcium phosphate dihydrate), GIC + 15% DCPD, GIC + 5% ß-TCP (tricalcium phosphate), GIC + 15% ß-TCP (by mass), and CSC were evaluated for Ca2+/Sr2+/F- release in water for 56 days. Cement mass loss was evaluated after 7-day immersion in water. Partially demineralized dentin disks were kept in contact with materials while immersed in simulated body fluid (SBF) at 37 °C for 56 days. The "mineral-to-matrix ratio" (MMR) was determined by ATR-FTIR spectroscopy. Dentin hardness and elastic modulus were obtained by nanoindentation. Samples were observed under scanning and transmission electron microscopy. Data were analyzed by ANOVA/Tukey test (α = 0.05). RESULTS: Ca2+ release from CSC and GIC (µg/cm2) were 4737.0 ± 735.9 and 13.6 ± 1.6, respectively. In relation to the unmodified GIC, the addition of DCPD or ß-TCP increased ion release (p < 0.001). Only the dentin disks in contact with CSC presented higher MMR (p < 0.05) and mechanical properties than those restored with a resin composite used as control (p < 0.05). Mass loss was similar for GIC and CSC; however, the addition of DCPD or ß-TCP increased GIC degradation (p < 0.05). CONCLUSION: Despite the increase in ion release, the additional Ca2+ sources did not impart remineralizing capability to GIC. Both unmodified GIC and CSC showed similar degradation in water. CLINICAL RELEVANCE: CSC was able to promote dentin remineralization.

In-vitro evaluation of fracture resistance of teeth restored with different high-viscosity glass ionomer restorative materials and bulk-fill composite resins.

OBJECTIVES: This study aimed to evaluate the effect of restorations made with a glass-hybrid restorative system (GHRS), a high-viscosity glass ionomer restorative material (HVGIC), a high-viscosity bulk-fill composite resin (HVB), a flowable bulk-fill composite resin (FB), and a nanohybrid composite resin (NH), which are commonly preferred in clinical applications on the fracture resistance of teeth in-vitro. MATERIALS AND METHODS: One hundred intact human premolar teeth were included in the study. The teeth were randomly divided into ten groups (n = 10). No treatment was applied to the teeth in Control group. Class II cavities were prepared on the mesial surfaces of the remaining ninety teeth in other groups. For restoration of the teeth, a GHRS, a HVGIC, a HVB, a FB, and a NH were used. Additionally, in four groups, teeth were restored using NH, GHRS, and HVGIC with open and closed-sandwich techniques. After 24 h, fracture resistance testing was performed. One-way ANOVA and Tukey HDS tests were used for statistical analysis of the data. RESULTS: The fracture resistance values of Control group were statistically significantly higher than those of GHRS, HVGIC, FB, NH, HVGIC-CS, GHRS-OS, and HVGIC-OS groups(p < 0.05). There was no statistically significant difference observed between the fracture resistance values of Control, HVB, and GHRS-CS groups (p > 0.05). CONCLUSION: It can be concluded that the use of HVB and the application of GHRS with a closed-sandwich technique may have a positive effect on the fracture resistance of teeth in the restoration of wide Class II cavities. CLINICAL RELEVANCE: The use of high-viscosity bulk-fill composite resin and the application of glass-hybrid restorative system with the closed-sandwich technique in the restoration of teeth with wide Class II cavities could increase the fracture resistance of the teeth.

Novel microbial synthesis of titania nanoparticles using probiotic Bacillus coagulans and its role in enhancing the microhardness of glass ionomer restorative materials.

Dental caries is a commonly occurring non-communicable disease throughout the world that might compromise the quality of any individual's life. Glass ionomer cements (GIC) are the most acceptable restorative materials due to their ease of manipulation, minimal tooth loss and least invasive strategy; however, they lack mechanical stability that has become a point of concern. Nanoparticles (NPs) are an outstanding option for modifying and enhancing the properties of dental materials. The focus of this study was to prepare novel, biocompatible titania dioxide (TiO2) NPs as a dental-restorative material using an efficient probiotic Bacillus coagulans. The prepared NPs were incorporated into glass ionomer restorative material at varying concentrations and investigated for cell viability percentage, microhardness and surface morphology. Results indicated that pure 100% anatase phase TiO2 NPs with particle size of 21.84 nm arranged in smooth, spherical agglomerates and clusters forms. These NPs depicted cell viability > 90%, thus confirming their non-cytotoxic behavior. GIC restorative materials reinforced by 5% titania (TiO2) NPs demonstrated the highest microhardness in comparison to the control group and other experimental groups of the study. Surface morphology analysis revealed a reduction in cracks in this novel dental-restorative material supporting its compatible biological nature with better hardness strength and negligible crack propagation. Overall, these results indicated that TiO2 NPs produced using a biological approach could be easily used as restorative materials in dental applications.

Long-term clinical comparison of a resin-based composite and resin modified glass ionomer in the treatment of cervical caries lesions.

This 72-month study compared the clinical effectiveness of a resin-based composite (RBC) (Spectrum TPH3, Dentsply Sirona) with a resin-modified glass ionomer cement (RMGIC) (Riva Light Cure, SDI) in restoring cervical caries lesions (CCLs). Thirty-three patients, each with at least two CCLs, were enrolled. After caries removal, the dimensions of the cavities were recorded. In a split-mouth study design, a total of 110 restorations were randomly placed. Fifty-five restorations were placed with RBC using an etch-and-rinse adhesive system (Prime&Bond NT, Dentsply Sirona), while the remaining 55 were restored with RMGIC. The restorations were assessed at baseline, 6, 12, 18, 24, 36, 60, and 72 months according to modified USPHS criteria. Statistical analysis included Pearson Chi-square, Friedman tests, Kaplan Meier, and Logistic Regression analysis (p < 0.05). After 72 months, 47 restorations in 19 patients were evaluated (55% follow-up rate). Seventy-five percent of the RBC (n = 26) and 74% (n = 21) of the RMGIC restorations were fully retained. There were no significant differences between materials regarding retention and marginal adaptation (p > 0.05). Cavity dimensions, caries activity, and retention exhibited no correlation (p > 0.05). The increase in marginal staining in both groups over time was significant (p < 0.001). RMGIC restorations exhibited higher discoloration than RBC restorations (p = 0.014). At 72 months, three secondary caries lesions were detected in both restoration groups: two RMGIC and one RBC. There were no reports of sensitivity. After 72 months, both RBC and RMGIC restorations were clinically successful, with similar retention and marginal adaptation scores. However, it is noteworthy that RMGIC restorations tend to discoloration over time compared to RBC. The trial is registered in the database of "Clinical Trials". The registration number is NCT0372-2758, October 29, 2018.

Evaluation of mechanical, optical, and fluoride-releasing properties of a translucent bulk fill glass hybrid restorative dental material.

OBJECTIVE: Measure and compare the mechanical properties, translucency, and fluoride-releasing capabilities of EQUIA Forte HT against Fuji IX GP and ChemFil Rock. MATERIALS AND METHODS: Ten specimens of each material were fabricated for compressive strength (CS), flexural strength (FS), and surface hardness analysis at 24 h and 7 days. The L*a*b* values were measured against a black-and-white background using a spectrophotometer to analyze the translucency parameter (TP). Fluoride release was recorded after 2 months of immersion in distilled water. The mean data was analyzed by 1- and 2-way ANOVA (α = 0.5). RESULTS: EQUIA Forte HT showed higher CS, surface hardness, and FS values (p < 0.05) compared with Fuji IX GIC, while no significant difference was found in FS values between EQUIA Forte HT and Chemfil Rock (p > 0.05). The EQUIA Forte HT exhibited significantly higher translucency in comparison to both ChemFil Rock (p < 0.001) and Fuji IX GICs (p < 0.05). An increase (p > 0.05) of fluoride release was observed for EQUIA Forte HT. CONCLUSION: The EQUIA Forte HT Glass-ionomer cements (GIC) offers enhanced translucency, improved strength, and enhanced fluoride-releasing properties compared to the traditionally used Fuji IX GIC and ChemFil Rock GICs. This material might have a wide range of clinical applications due to its improved strength and optical properties. CLINICAL SIGNIFICANCE: Glass-ionomer dental restorative materials possess unique advantageous characteristics. However, its poor mechanical and optical properties have typically limited its clinical applications. Efforts to improve these properties have resulted in enhanced GICs. EQUIA Forte HT GIC offers enhanced mechanical and optical properties with potential applications in posterior and anterior restorative procedures.

Inhibitory Effects of Surface Pre-Reacted Glass Ionomer Filler Eluate on Streptococcus mutans in the Presence of Sucrose.

The surface pre-reacted glass ionomer (S-PRG) filler is a type of bioactive functional glass that releases six different ions. This study examined the effects of the S-PRG filler eluate on Streptococcus mutans in the presence of sucrose. In a solution containing S. mutans, the concentrations of BO33-, Al3+, Sr2+, and F- were significantly higher in the presence of the S-PRG filler eluate than in its absence (p < 0.001). The concentrations of these ions further increased in the presence of sucrose. Additionally, the S-PRG filler eluate significantly reduced glucan formation by S. mutans (p < 0.001) and significantly increased the pH of the bacterial suspension (p < 0.001). Bioinformatic analyses revealed that the S-PRG filler eluate downregulated genes involved in purine biosynthesis (purC, purF, purL, purM, and purN) and upregulated genes involved in osmotic pressure (opuAa and opuAb). At a low pH (5.0), the S-PRG filler eluate completely inhibited the growth of S. mutans in the presence of sucrose and significantly increased the osmotic pressure of the bacterial suspension compared with the control (p < 0.001). These findings suggest that ions released from the S-PRG filler induce gene expression changes and exert an inhibitory effect on S. mutans in the presence of sucrose.

Could bulk fill glass hybrid restorative materials replace composite resins in treating permanent teeth? A randomized controlled clinical trial.

OBJECTIVE: This study aims to compare the clinical and radiographic efficacy of Equia system bulk fill glass hybrid material with composite resins in the permanent restoration of pediatric patients' permanent teeth. MATERIALS AND METHODS: The study included 44 pediatric patients aged 8-16 who applied to Necmettin Erbakan University Pediatric Dentistry Department. The groups were formed as symmetrical teeth in the same patient using the split-mouth design. The study included class I caries lesions of 144 permanent teeth. Group 1 was restored with the Equia system bulk fill glass hybrid material (Equia Forte HT + Equia Forte Coat [GC, Co, Tokyo, Japan]) (n = 72) and Group 2 with the Charisma Smart universal composite resin (Kulzer, Gmbh, Hanau, Germany) + Clearfil SE Bond (Kuraray, Noritake, Sakazu, Okayama) (n = 72). Evaluations were performed clinically and radiographically by two physicians in 2nd week, 3rd month, 6th month, and 12th month and the results were recorded. Clinical evaluation was carried out using modified-USPHS criteria. Obtained data were statistically analyzed using Kendall's W test and Cochran's Q test for the comparison within the group, and the Chi-square test for the comparison between groups. RESULTS: Among the materials utilized in the study, there was no statistically significant difference in marginal adaptation, marginal discoloration, retention, anatomical form, postoperative sensitivity, and secondary caries according (p > 0.05). Group 2 outperformed statistically significant Group 1 in terms of color match in all periods (p < 0.05). While there was no statistically significant difference in surface structure between the groups in 2nd week and 3rd month (p > 0.05), there was a statistically substantial difference in 6th, and 12th months (p < 0.05). No secondary caries or periapical lesions were found in any restorations during radiographic evaluation. CONCLUSION: After a year, the clinical performance of both Equia and composite resins was equivalent and successful in the majority of the measures against which they were evaluated. CLINICAL SIGNIFICANCE: Based on the results of the research, Equia system bulk fill glass hybrid restorations are considered a viable alternative to composite resins in class I permanent teeth restorations.

[An unusual case: fracture of the handle of the malleus due to finger manipulation]. / Ein ungewöhnlicher Fall: Fraktur des Hammergriffs durch Fingermanipulation.

An isolated fracture of the handle of the malleus is a rare entity in otorhinolaryngology and manifests clinically as acute-onset unilateral hearing loss. Several factors may cause this injury, including acute barotraumatic pressure changes or traumatic events. Various therapeutic approaches such as tympanoplasty, autologous graft, or application of bone cement are discussed. We report the case of a 46-year-old female patient who developed acute hearing loss in her left ear after finger manipulation. Clinical evaluation revealed axial displacement of the handle of the malleus and audiometry indicated conductive hearing loss. After otoscopy, audiometry, and computed tomography, tympanoscopy was indicated due to suspicion of ossicular chain disruption. Intraoperatively, an isolated fracture of the handle of malleus was found, which was treated with glass ionomer cement. Following postoperative examination, there was progressive improvement in the acoustic transmission component, such that a normal hearing threshold was observed 4 months postoperatively. This case report underlines the importance of precise diagnosis and individualized treatment for rare middle ear injuries.

Effect of silver diamine fluoride on the microleakage of flowable resin composite and glass ionomer cement restorations to carious primary dentin: an-in vitro study.

BACKGROUND: This study aimed to evaluate the effect of Silver Diamine Fluoride (SDF) on the microleakage of flowable resin composite (FRC) and resin-modified glass ionomer cement (GIC) restorations bound to carious primary dentin. METHODS: Forty-four extracted carious primary molars were allocated into four groups as follows (n = 11 teeth/group): Group I, Flowable resin composite (FRCa): SDF38% treatment + FRC, Group II, Flowable resin composite (FRCb): FRC without SDF treatment, Group III, Resin-modified glass ionomer cement (GICa): SDF38% treatment + GIC, Group IV, Resin-modified glass ionomer cement (GICb): GIC without SDF treatment. Specimens were subjected to thermo cycling at 500 cycles between 5 to 55 °C (dwell time of 60 seconds) in baths before being immersed for 24 h in a 1% toluidine blue solution. Microleakage testing was conducted for each specimen in two areas; occlusal and gingival. Specimens were evaluated under stereomicroscope at 4x magnification. Results were analyzed using Kruskal-Wallis test followed by pairwise comparisons utilizing Dunn's post hoc test at p ≤ 0.05. RESULTS: Insignificant differences between different groups (p = 0.49) were observed at the gingival walls area readings. The highest value was found in GICb (2.33 ± 0.52), while the lowest value was found in FRCa (1.71 ± 0.76). Insignificant differences between different groups (p = 0.982) were observed at the occlusal walls area readings. The highest value was found in FRCa (1.43 ± 0.98), while the lowest value was found in GICb (1.17 ± 1.33). CONCLUSION: SDF does not adversely affect the microleakage of FRC and GIC restorations bound to carious primary dentin.

Microhardness and elemental analysis of ion-releasing restoration/ dentin interface following enzymatic chemomechanical caries excavation.

BACKGROUND: This study was conducted to compare chemical, elemental and surface properties of sound and carious dentin after application of two restorative materials resin-modified glassionomer claimed to be bioactive and glass hybrid restorative material after enzymatic chemomechanical caries removal (CMCR) agent. METHODS: Forty carious and twenty non-carious human permanent molars were used. Molars were randomly distributed into three main groups: Group 1 (negative control) - sound molars, Group 2 (positive control) - molars were left without caries removal and Group 3 (Test Group) caries excavated with enzymatic based CMCR agent. After caries excavation and restoration application, all specimens were prepared Vickers microhardness test (VHN), for elemental analysis using Energy Dispersive Xray (EDX) mapping and finally chemical analysis using Micro-Raman microscopy. RESULTS: Vickers microhardness values of dentin with the claimed bioactive GIC specimens was statistically higher than with glass hybrid GIC specimens. EDX analysis at the junction estimated: Calcium and Phosphorus of the glass hybrid GIC showed insignificantly higher mean valued than that of the bioactive GIC. Silica and Aluminum mean values at the junction were significantly higher with bioactive GIC specimens than glass hybrid GIC specimen. Micro-raman spectroscopy revealed that bioactive GIC specimens showed higher frequencies of v 1 PO 4, which indicated high level of remineralization. CONCLUSIONS: It was concluded that ion-releasing bioactive resin-based restorative material had increased the microhardness and remineralization rate of carries affected and sound dentin. In addition, enzymatic caries excavation with papain-based CMCR agent has no adverse effect on dentin substrate.

Effect of various surface coating methods on surface roughness, micromorphological analysis and fluoride release from contemporary glass ionomer restorations.

OBJECTIVE: To evaluate the effect of various surface coating methods on surface roughness, micromorphological analysis and fluoride release from contemporary resin-modified and conventional glass ionomer restorations. MATERIALS & METHODS: A total of 72 permanent human molars were used in this study. The teeth were randomly assigned into 2 groups according to type of restorative materials used; resin modified glass ionomer cement and conventional glass ionomer (SDI Limited. Bayswater Victoria, Australia). Each group was subdivided into 3 subgroups according to the application of coat material; Sub-group1: without application of coat; Sub-group2: manufacturer recommended coat was applied and sub-group3: customized (vaseline) coat was applied. Each group was then subdivided into two divisions according to the time of testing; immediate (after 24 h) and delayed (after 6 months of storage). Three specimens from each sub-group were selected for surface roughness test (AFM) and another 3 specimens for the micromorphological analysis using scanning electron microscope (SEM). For the fluoride release test, a total of 60 cylindrical discs were used (n = 60). The discs were randomly split into 2 groups according to type of restorative materials used (n = 30); resin modified glass ionomer cement and conventional glass ionomer. Each group was subdivided into 3 subgroups (n = 10) according to the application of the coat material; Sub-group1: without application of coat; Sub-group2: with the manufacturer recommended coat and sub-group3: with application of customized (vaseline) coat. Data for each test was then collected, tabulated, were collected, tabulated, and tested for the normality with Shapiro-Wilk test. Based on the outcome of normality test, the significant effects of variables were assessed using appropriate statistical analysis testing methods. RESULTS: Regarding the data obtained from surface roughness test, Shapiro-Wilk test showed normal distribution pattern of all values (p > 0.05). Accordingly, Two-way ANOVA outcome showed that the 'type of restoration' or 'test time' had statistically significant effect on the AFM test (p < 0.05). Regarding Fluoride specific ion electrode test 2-way ANOVA followed by Least Significant Difference (LSD) Post-hoc test revealed significant difference among the groups (p < 0.05). It showed that SDI GIC group after 14 days of measurement had the highest mean of fluoride release (36.38 ± 3.16 PPM) and SDI RMGIC after 30 days of measurement had the second highest mean of fluoride release (43.28 ± 1.89 PPM). Finally, regarding the micromorphological analysis using SEM, a slight difference was observed between the studied groups. CONCLUSIONS: Based on the results of this study, various coatings enhance surface roughness in the initial 24 h of restoration insertion. Different coat types seems that have no influence on fluoride release and the micromorphological features of the restoration/dentin interface.

Evaluation of setting kinetics, mechanical strength, ion release, and cytotoxicity of high-strength glass ionomer cement contained elastomeric micelles.

BACKGROUND: Low mechanical properties are the main limitation of glass ionomer cements (GICs). The incorporation of elastomeric micelles is expected to enhance the strength of GICs without detrimentally affecting their physical properties and biocompatibility. This study compared the chemical and mechanical properties, as well as the cytotoxicity, of elastomeric micelles-containing glass ionomer cement (DeltaFil, DT) with commonly used materials, including EQUIA Forte Fil (EF), Fuji IX GP Extra (F9), and Ketac Molar (KT). METHOD: Powder particles of GICs were examined with SEM-EDX. Setting kinetics were assessed using ATR-FTIR. Biaxial flexural strength/modulus and Vickers surface microhardness were measured after immersion in water for 24 h and 4 weeks. The release of F, Al, Sr, and P in water over 8 weeks was analyzed using a fluoride-specific electrode and ICP-OES. The toxicity of the material extract on mouse fibroblasts was also evaluated. RESULTS: High fluoride levels in the powder were detected with EF and F9. DT demonstrated an initial delay followed by a faster acid reaction compared to other cements, suggesting an improved snap set. DT also exhibited superior flexural strength than other materials at both 24 h and 4 weeks but lower surface microhardness (p < 0.05). EF and F9 showed higher release of F, Al, and P than DT and KT. There was no statistically significant difference in fibroblast viability among the tested materials (p > 0.05). CONCLUSIONS: Elastomeric micelles-containing glass ionomer cement (DT) exhibited satisfactory mechanical properties and cytocompatibility compared with other materials. DT could, therefore, potentially be considered an alternative high-strength GIC for load-bearing restorations.