An Intrinsic Stable Layered Oxide Cathode for Practical Sodium-Ion Battery: Solid Solution Reaction, Near-Zero-Strain and Marvelous Water Stability.

Non-aqueous solvents, in particular N,N-dimethylaniline (NMP), are widely applied for electrode fabrication since most sodium layered oxide cathode materials are readily damaged by water molecules. However, the expensive price and poisonousness of NMP unquestionably increase the cost of preparation and post-processing. Therefore, developing an intrinsically stable cathode material that can implement the water-soluble binder to fabricate an electrode is urgent. Herein, a stable nanosheet-like Mn-based cathode material is synthesized as a prototype to verify its practical applicability in sodium-ion batteries (SIBs). The as-prepared material displays excellent electrochemical performance and remarkable water stability, and it still maintains a satisfactory performance of 79.6% capacity retention after 500 cycles even after water treatment. The in situ X-ray diffraction (XRD) demonstrates that the synthesized material shows an absolute solid-solution reaction mechanism and near-zero-strain. Moreover, the electrochemical performance of the electrode fabricated with a water-soluble binder shows excellent long-cycling stability (67.9% capacity retention after 500 cycles). This work may offer new insights into the rational design of marvelous water stability cathode materials for practical SIBs.

Optimization Strategy in Hydrogen Storage Performance of Ti─V─Cr─Mn Alloys via LiAlH4.

V-based solid solution materials hold a significant position in the realm of hydrogen storage materials because of its high hydrogen storage capacity. However, the current dehydrogenation temperature of V-based solid solution exceeds 350 °C, making it challenging to fulfill the appliance under moderate conditions. Here advancements in the hydrogen storage properties and related mechanisms of TiV1.1Cr0.3Mn0.6 + x LiAlH4 (x = 0, 5, 8, 10 wt.%) composites is presented. According to the first principle calculation analysis, the inclusion of Al and Li atoms will lower the binding energy of hydride, thus enhancing the hydrogen absorption reaction and significantly decreasing the activation difficulty. Furthermore, based on crystal orbital Hamilton population (COHP) analysis, the strength of the V─H and Ti─H bonds after doping LiAlH4 are reduced, leading to a decrease of the hydrogen release activation energy (Ea) for the V-based solid solution material, thus the hydrogen release process is easier to carry out. Additionally, the structure of doped LiAlH4 exhibits an outstanding hydrogen release rate of 2.001 wt.% at 323 K and remarkable cycling stability.

Fluoride Doping Na3Al2/3V4/3(PO4)3 Microspheres As Cathode Materials for Sodium-Ion Batteries with Multielectron Redox.

Sodium-ion batteries (SIBs) are potential candidates for large energy storage usage because of the natural abundance and cheap sodium. Nevertheless, improving the energy density and cycling steadiness of SIB cathodes remains a challenge. In this work, F-doping Na3Al2/3V4/3(PO4)3(NAVP) microspheres (Na3Al2/3V4/3(PO4)2.9F0.3(NAVPF)) are synthesized via spray drying and investigated as SIB cathodes. XRD and Rietveld refinement reveal expanded lattice parameters for NAVPF compared to the undoped sample, and the successful cation doping into the Na superionic conductor (NASICON) framework improves Na+ diffusion channels. The NAVPF delivers an ultrahigh capacity of 148 mAh g-1 at 100 mA g-1 with 90.8% retention after 200 cycles, enabled by the activation of V2+/V5+ multielectron reaction. Notably, NAVPF delivers an ultrahigh rate performance, with a discharge capacity of 83.6 mAh g-1 at 5000 mA g-1. In situ XRD demonstrates solid-solution reactions occurred during charge-discharge of NAVPF without two-phase reactions, indicating enhanced structural stability after F-doped. The full cell with NAVPF cathode and Na+ preintercalated hard carbon anode shows a large discharge capacity of 100 mAh g-1 at 100 mA g-1 with 80.2% retention after 100 cycles. This anion doping strategy creates a promising SIB cathode candidate for future high-energy-density energy storage applications.

Coprecipitation of Ce(III) oxide with UO2.

The neutralization of acidic solutions containing U (IV) and Ce (III) at room temperature in glove box atmosphere and in the presence of dithionite results in coprecipitation of these elements as amorphous solid solutions CexU1-xO2±y. The solubilities of the precipitates with different mole fractions (x) of Ce(OH)3 (x = 0.01 or 0.1) were determined in 1 M NaClO4 solutions between pH 2.2 and 12.8 under reducing conditions. The solids were investigated by a variety of methods (chemical analysis, SEM-EDX, XRD, XPS, XAS) to determine the nature of the solid solutions formed, their composition and the valence state of Ce and U. X-ray photoelectron spectroscopy confirmed the oxidation states of the solids both before and after the equilibration as Ce (III) and U (IV). The amorphous coprecipitates reached equilibrium relatively fast (∼1 week). The release of Ce from the coprecipitates was totally dominated by the release of uranium over the whole pH range. The Ce concentrations decrease slightly with the decrease of Ce content in the solid, suggesting that CexU1-xO2±y solids behave thermodynamically as solid solutions. The concentrations of U in equilibrium with the coprecipitate were in excellent agreement with the solubility of UO2(s) under reducing conditions reported in the literature. The conditional solubility product of Ce(OH)3 from the coprecipitate was several orders of magnitude (∼4 in the near neutral pH range and ∼18 in the acidic range) lower than that of pure Ce(OH)3(s). The activities and activity coefficients of Ce(OH)3(s) in the coprecipitate were also estimated. Activity coefficients are much less than 1, indicating that the mixing of Ce(OH)3 with UO2 is highly favorable.

Construction of Co1-xZnxFe2xGa2-2xO4 (02 Reduction by H2O Vapour.

Solid solutions are garnering substantial attention in the realm of solar energy utilization due to their tunable electronic properties, encompassing band edge positions and charge-carrier mobilities. In this study, we designed and synthesized Co1-xZnxFe2xGa2-2xO4 (0

Hollow-Carbon Confinement Annealing: A New Synthetic Approach to Make High-Entropy Solid-Solution and Intermetallic Nanoparticles.

High-entropy alloy (HEA) nanoparticles (NPs) have been emerging with superior compositional tunability and multielemental synergy, presenting a unique platform for material discovery and performance optimization. Here we report a synthetic approach utilizing hollow-carbon confinement in the ordinary furnace annealing to achieve the nonequilibrium HEA-NPs such as Pt0.45Fe0.18Co0.12Ni0.15Mn0.10 with uniform size ∼5.9 nm. The facile temperature control allows us not only to reveal the detailed reaction pathway through ex situ characterization but also to tailor the HEA-NP structure from the crystalline solid solution to intermetallic. The preconfinement of metal precursors is the key to ensure the uniform distribution of metal nanoparticles with confined volume, which is essential to prevent the thermodynamically favored phase separation even during the ordinary furnace annealing. Besides, the synthesized HEA-NPs exhibit remarkable activity and stability in oxygen reduction catalysis. The demonstrated synthetic approach may significantly expand the scope of HEA-NPs with uncharted composition and performance.

Synthesis of Mesoporous Tetragonal ZrO2, TiO2 and Solid Solutions and Effect of Colloidal Silica on Porosity.

Metal oxides possessing a large surface area, pore volume and desirable pore size provide more varieties and active industrial potentials. Nevertheless, it is very challenging to produce crystal metal oxides while keeping satisfactory porosity features, especially for ternary compositions. High temperature is usually needed to produce crystal metal oxides, which readily leads to the collapse of the pore structure. Herein, by employing a 'soft' dispersant agent and a hard silica template, ZrO2, TiO2 and Zr-Ti solid solutions having a tetragonal crystal structure are produced and the silica-leached materials are characterized from macroscopic to atomistic scales. The micron-sized particulate powders are composed of nanoscale 'building blocks', with crystallite sizes between ~8 and 21 nm. These polycrystalline ceramic powders exhibit a high specific surface area (up to ~200 m2·g-1) and pore volume (up to 0.5 cm3·g-1), with a pore size range of ~5-20 nm. Importantly, the Zr/Ti-O-Si-OH chemical bonds exist on the particle surface, with about two-thirds of the surface covered by silica. The hydroxyl groups can further post-graft organic ligands or directly associate with species. Synthesized mesoporous metal oxides are highly homogenous and could potentially be used in various applications because of their tetragonal structure and porosity features.

Effective CO2 Thermocatalytic Hydrogenation with High Coke Resistance on Ni-CZ/Attapulgite Composite.

Converting CO2 into methane is considered a promising and economically viable technology for global transportation and utilization of this greenhouse gas. This study involves the preparation of a Ni-CZ (CeO2-ZrO2)/ATP (attapulgite) catalyst through the co-precipitation and impregnation methods. XRD, SEM, TEM, N2 absorption-desorption isotherms, XPS, H2-TPR, CO2-TPD, TG/DSC, and Raman were adapted to characterize the obtained samples. Real-time GC was used to measure the catalytic performances and to intensively study the impact of Ni loading content and ATP to CZ ratio on the catalytic performance of the products. DRIFTs was used to monitor the interstitial radicals in the catalytic reactions and to deduce the catalytic mechanisms. The results indicate that the composite catalytic matrix composed of CZ assembled on ATP demonstrated higher CO2 methanation stability and better carbon deposition resistance ability than the single CZ or ATP as the carrier, which should be attributed to the improved specific surface area and pore volume of the ATP assembled matrix and the enhanced dispersibility of the CZ and Ni species. The adoption of CZ solid solutions improves the oxygen storage capability of the catalyst, thereby providing continued mobile O2- in the matrix and accelerating the molecular exchange rate in the catalytic reactions. The ideal loading quantity of nickel contents on the CZA matrix is 15%, as the CO2 conversion decreases at elevated temperatures when the Ni loading content reaches 20%. Among the tested samples, the 15Ni-0.8CZA sample showed the best catalytic performance of 75% CO2 conversion and 100% CH4 selectivity at 400 °C. After 50 h of stability tests, the CO2 conversion rate still remained 70.84%, and the CH4 selectivity obtained 97.46%. No obvious coke was detected according to the Raman spectra of the used catalyst. The in situ DRIFTS experiment showed that formate is the main intermediate of the CO2 hydrogenation reaction on the 15Ni-0.8CZA catalyst.

Interfacial Engineering for Oriented Crystal Growth toward Dendrite-Free Zn Anode for Aqueous Zinc Metal Battery.

Zn deposition with a surface-preferred (002) crystal plane has attracted extensive attention due to its inhibited dendrite growth and side reactions. However, the nucleation and growth of the Zn(002) crystal plane are closely related to the interfacial properties. Herein, oriented growth of Zn(002) crystal plane is realized on Ag-modified surface that is directly visualized by in situ atomic force microscopy. A solid solution HCP-Zn (~1.10 at. % solubility of Ag, 30 °C) is formed on the Ag coated Zn foil (Zn@Ag) and possesses the same crystal structure as Zn to reduce its nucleation barrier caused by their lattice mismatch. It merits oriented Zn deposition and corrosion-resistant surface, and presents long cycling stability in symmetric cells and full cells coupled with V2O5 cathode. This work provides insights into interfacial regulation of Zn anodes for high-performance aqueous zinc metal batteries.

In Situ Formation of Platinum-Carbon Catalysts in Propane Dehydrogenation.

The catalytic production of propylene via propane dehydrogenation (PDH) is a key reaction in the chemical industry. By combining operando transmission electron microscopy with density functional theory analysis, we show that the intercalation and ordering of carbon on Pt interstitials to form Pt-C solid solutions is relevant for increasing propylene production. More specifically, we found that at the point of enhanced propylene formation, the structure of platinum nanoparticles is transformed into a transient caesium chloride-type Pt-C polymorph. At more elevated temperatures, the zincblende and rock salt polymorphs seemingly coexist. When propylene production was highest, multiple crystal structures consisting of Pt and carbon were occasionally found to coexist in one individual nanoparticle, distorting the Pt lattice. Catalyst coking was detected at all stages of the reaction, but did initially not affect all particles. These findings could lead to the development of novel synthesis strategies towards tailoring highly efficient PDH catalysts.

Negative Lattice Expansion in an O3-Type Transition-Metal Oxide Cathode for Highly Stable Sodium-Ion Batteries.

The sodium extraction/insertion in layered transition-metal oxide (TMO) cathode materials are typically accompanied by slab sliding and lattice changes, leading to microstructure destruction and capacity decay. Herein, negative lattice expansion is observed in an O3 type Ni-based layered cathode of Na0.9 Ni0.32 Zn0.08 Fe0.1 Mn0.3 Ti0.2 O2 upon Na+ extraction. It is attributed to the weak Zn2+ -O2- orbital hybridization and increased electron density of the surrounding oxygen for reinforced interlayer O-O repulsive force. This enables gliding of TMO slabs for the intergrowth phase transition of P3→OP2 to alleviate lattice strain with moderate lattice shrinkage, which exhibits general interslab spacings and volume changes as low as 2.4 % and 1.9 %, respectively. The strong Ti-O bonds accommodate the internal distortion of TMO6 octahedra due to the flexibility of TiO6 octahedra during cycling. These endow a high specific capacity of 144.9 mAh g-1 and excellent cycling performance of pouch-type sodium-ion batteries with 93 % capacity retention after 3600 cycles.

Structural Engineering Enabled Bimetallic (Ti1- y Nby )2 AlC Solid Solution Structure for Efficient Electromagnetic Wave Absorption in Gigahertz.

Microstructures play a critical role to influence the polarization behavior of dielectric materials, which determines the electromagnetic response ability in gigahertz. However, the relationship between them, especially in the solid-solution structures is still absent. Herein, a series of (Ti1- y Nby )2 AlC MAX phase solid solutions with nano-laminated structures have been employed to illuminate the aforementioned problem. The relationship has been investigated by the lattice distortion constructed via tuning the composition from Ti to Nb in the M-site atomic layer. Experimental characterizations indicated that the dielectric response behaviors between declined conduction loss and boosted polarization loss can be well balanced by niobium atom manipulative solid-solution engineering, which is conducive to impedance matching and electromagnetic absorption performance. Theoretical calculation further proved that the origin of electric dipoles is ascribed to the charge density differences resulting from the altered microscopic atomic distribution. As a result, the Ti1.2 Nb0.8 AlC exhibits the mostly optimized microwave absorption property, in which a minimum reflection loss of -42 dB and an effective absorption bandwidth of 4.3 GHz under an ultra-thin thickness of 1.4 mm can be obtained. This work provides insight into the structural engineering in modifying electromagnetic response performance at gigahertz and which can be expanded to other solid-solution materials.

Whole-Voltage-Range Solid-Solution Reaction in Layered Oxide Cathode of Sodium-Ion Batteries.

Layered manganese-based oxides (LMOs) are promising cathode materials for sodium-ion batteries (SIBs) due to their versatile structures. However, the Jahn-Teller effect of Mn3+ induces severe distortion of MnO6 octahedra, and the resultant low symmetry is responsible for the gliding of MnO2 layers and then inferior multiple-phase transitions upon Na+ extraction/insertion. Here, hexagonal P2-Na0.643 Li0.078 Mn0.827 Ti0.095 O2 is synthesized through the incorporation of Li and Ti into the distorted orthorhombic P'2-Na0.67 MnO2 to function as a phase-transition-free oxide cathode. It is revealed that Li in both the transition-metal and Na layers enhances the covalency of Mn-O bonds and allows degeneracy of Mn 3d eg orbitals to favor the formation of hexagonal phase, and the high strength of Ti-O bonds reduces the electrostatic interaction between Na and O for suppressed Na+ /vacancy rearrangements. These collectively lead to a whole-voltage-range solid-solution reaction between 1.8 and 4.3 V with a small volume variation of 1.49%. This rewards its excellent cycling stability (capacity retention of 90% after 500 cycles) and rate capability (89 mAh g-1 at 2000 mA g-1 ).

Design and Synthesis of Noble Metal-Based Alloy Electrocatalysts and Their Application in Hydrogen Evolution Reaction.

Hydrogen energy is regarded as the ultimate energy source for future human society, and the preparation of hydrogen from water electrolysis is recognized as the most ideal way. One of the key factors to achieve large-scale hydrogen production by water splitting is the availability of highly active and stable electrocatalysts. Although non-precious metal electrocatalysts have made great strides in recent years, the best hydrogen evolution reaction (HER) electrocatalysts are still based on noble metals. Therefore, it is particularly important to improve the overall activity of the electrocatalysts while reducing the noble metals load. Alloying strategies can shoulder the burden of optimizing electrocatalysts cost and improving electrocatalysts performance. With this in mind, recent work on the application of noble metal-based alloy electrocatalysts in the field of hydrogen production from water electrolysis is summarized. In this review, first, the mechanism of HER is described; then, the current development of synthesis methods for alloy electrocatalysts is presented; finally, an example analysis of practical application studies on alloy electrocatalysts in hydrogen production is presented. In addition, at the end of this review, the prospects, opportunities, and challenges facing noble metal-based alloy electrocatalysts are tried to discuss.

Effect of Si on the Oxidation Behaviors of Ti3 Al1-x Six C2 at 1000 °C.

In this work, Ti3 Al1-x Six C2 (x=0, 0.2, 0.4, and 0.6) with Al/Si solid solution structure are synthesized, and the effects of Si on their oxidation behaviors at 1000 °C are evaluated. The addition of Si not only contributes to the formation of Ti5 Si3 impurity but also affects the composition of the oxide scale. Particularly, the incorporation of Si in the TiO2 lattice is demonstrated, which alters the formation energy of the (110) plane in TiO2 , thus leading to the preferential growth of Si-doped TiO2 to dendritic congeries. Moreover, the Si addition is believed to affect mass transportation during the oxidation process, which accelerates the formation of a continuous Al2 O3 layer in the oxide scale. With an optimized Si content, the oxidation of Ti3 Al1-x Six C2 is restrained. However, with excess Si content, the continuity of the resulting Al2 O3 layer is destroyed, thus the oxidation rate rises again.

Coherent lamellar intergrowth in alkali feldspar.

A thermodynamic analysis of coherent lamellar intergrowth resulting from the exsolution of initially homogeneous alkali feldspar is presented. In contrast to earlier treatments, where the simplifying assumption of zero strain in the lamellar interfaces was used, our treatment is more general. The elastic stresses and strains associated with coherent lamellar intergrowth of Na-rich and K-rich alkali feldspar are calculated by minimising the overall elastic energy of the lamellar microstructure. At given pressure and temperature, the elastic energy depends on the volume proportions of the two lamellar types, and thus on the composition of the homogeneous precursor feldspar. As a consequence, there is no single coherent solvus for alkali feldspar, but coherent solvi are different for different compositions of the homogeneous precursor phase. Experimentally observed lamellar orientations agree with those predicted by minimising the strain energy on a set of all possible lamellar orientations.

Unusual activated processes controlling dislocation motion in body-centered-cubic high-entropy alloys.

Atomistic simulations of dislocation mobility reveal that body-centered cubic (BCC) high-entropy alloys (HEAs) are distinctly different from traditional BCC metals. HEAs are concentrated solutions in which composition fluctuation is almost inevitable. The resultant inhomogeneities, while locally promoting kink nucleation on screw dislocations, trap them against propagation with an appreciable energy barrier, replacing kink nucleation as the rate-limiting mechanism. Edge dislocations encounter a similar activated process of nanoscale segment detrapping, with comparable activation barrier. As a result, the mobility of edge dislocations, and hence their contribution to strength, becomes comparable to screw dislocations.

Crystal Structure and Thermal Properties of Double-Complex Salts [M1(NH3)6][M2(C2O4)3] (M1, M2 = Co, Rh) and K3[Rh(NH3)6][Rh(C2O4)3]2∙6H2O.

Here, seven new double-complex salts, [M1(NH3)6][M2(C2O4)3] (M1, M2 = Co, Rh) and K3[Rh(NH3)6][Rh(C2O4)3]2∙6H2O types, are synthesised. The crystal structure and composition of DCS (double-complex salts) are studied by SCXRD, XRD, CHN and IR methods. The complex salts of the [M1(NH3)6][M2(C2O4)3] (M1, M2 = Co, Rh) type can be crystallised both as a crystalline hydrate [M1(NH3)6][M2(C2O4)3]·3H2O (sp. gr. P-3) and as an anhydrous complex (sp. gr. P-1) depending on the synthesis conditions. The process of [Rh(NH3)6][Rh(C2O4)3] formation is significantly dependent on the synthesis temperature. At room temperature, a mixture is formed comprising [Rh(NH3)6][Rh(C2O4)3] and K3[Rh(NH3)6][Rh(C2O4)3]2∙6H2O, while the [Rh(NH3)6][Rh(C2O4)3] target product crystallises at elevated temperatures. The thermal behaviour of double-complex salts is studied by the STA, EGA-MS, IR and XRD methods. The complete decomposition of complex salts in helium and hydrogen atmospheres resulting in metals or CoxRh1-x solid solutions is achieved at temperatures of 320-450 °C.

Effects of different chemical agents on changes in sediment phosphorus composition and the response of sediment microbial community.

Controlling the release of sediment phosphorus (P) using chemical agents is a promising method for controlling internal P in eutrophic lakes. However, mineral P formation and changes in the organic P composition after sediment amendment with P-inactivation agents remain poorly understood. Furthermore, little is known about the changes in the sediment microbial community composition after remediation. Here, various ratios of poly aluminum chloride (PAC) and lanthanum-modified bentonite (LMB) were added to nutrient-rich sediments and incubated. Sequential P extraction, solution/solid-state 31P nuclear magnetic resonance (NMR), and microbial analyses were periodically performed on the inactivated sediments. The results indicate that PAC and LMB effectively reduced sediment iron-bound P and organic P, respectively, markedly increasing the content of aluminum- and calcium-bound P in the sediment, respectively. Solid-state 31P NMR results confirmed the formation of rhabdophane (LaPO4. nH2O) in the LMB-amended sediment. Solution 31P NMR results showed that PAC preferentially reduced the organic P fractions of pyrophosphate, whereas LMB efficiently reduced the organic P fractions of orthophosphate, monoesters, and diesters in the sediment. Compared with the control sediment, PAC addition can cause short-term negative effects on sediment microbes at high doses, whereas LMB addition can increase bacterial diversity or richness in the sediment. These results provide a deeper understanding of the differences between PAC and LMB in internal sediment P control.

Enhanced Solid-State Fluorescence of Flavin Derivatives by Incorporation in the Metal-Organic Frameworks MIL-53(Al) and MOF-5.

The flavin derivatives 10-methyl-isoalloxazine (MIA) and 6-fluoro-10-methyl-isoalloxazine (6F-MIA) were incorporated in two alternative metal-organic frameworks, (MOFs) MIL-53(Al) and MOF-5. We used a post-synthetic, diffusion-based incorporation into microcrystalline MIL-53 powders with one-dimensional (1D) pores and an in-situ approach during the synthesis of MOF-5 with its 3D channel network. The maximum amount of flavin dye incorporation is 3.9 wt% for MIA@MIL-53(Al) and 1.5 wt% for 6F-MIA@MIL-53(Al), 0.85 wt% for MIA@MOF-5 and 5.2 wt% for 6F-MIA@MOF-5. For the high incorporation yields the probability to have more than one dye molecule in a pore volume is significant. As compared to the flavins in solution, the fluorescence spectrum of these flavin@MOF composites is broadened at the bathocromic side especially for MIA. Time-resolved spectroscopy showed that multi-exponential fluorescence lifetimes were needed to describe the decays. The fluorescence-weighted lifetime of flavin@MOF of 4 ± 1 ns also corresponds to those in solution but is significantly prolonged compared to the solid flavin dyes with less than 1 ns, thereby confirming the concept of "solid solutions" for dye@MOF composites. The fluorescence quantum yield (ΦF) of the flavin@MOF composites is about half of the solution but is significantly higher compared to the solid flavin dyes. Both the fluorescence lifetime and quantum yield of flavin@MOF decrease with the flavin loading in MIL-53 due to the formation of various J-aggregates. Theoretical calculations using plane-wave and QM/MM methods are in good correspondence with the experimental results and explain the electronic structures as well as the photophysical properties of crystalline MIA and the flavin@MOF composites. In the solid flavins, π-stacking interactions of the molecules lead to a charge transfer state with low oscillator strength resulting in aggregation-caused quenching (ACQ) with low lifetimes and quantum yields. In the MOF pores, single flavin molecules represent a major population and the computed MIA@MOF structures do not find π-stacking interactions with the pore walls but only weak van-der-Waals contacts which reasons the enhanced fluorescence lifetime and quantum yield of the flavins in the composites compared to their neat solid state. To analyze the orientation of flavins in MOFs, we measured fluorescence anisotropy images of single flavin@MOF-5 crystals and a static ensemble flavin@MIL53 microcrystals, respectively. Based on image information, anisotropy distributions and overall curve of the time-resolved anisotropy curves combined with theoretical calculations, we can prove that all fluorescent flavins species have a defined and rather homogeneous orientation in the MOF framework. In MIL-53, the transition dipole moments of flavins are orientated along the 1D channel axis, whereas in MOF-5 we resolved an average orientation that is tilted with respect to the cubic crystal lattice. Notably, the more hydrophobic 6F-MIA exhibits a higher degree order than MIA. The flexible MOF MIL-53(Al) was optimized essentially to the experimental large-pore form in the guest-free state with QuantumEspresso (QE) and with MIA molecules in the pores the structure contracted to close to the experimental narrow-pore form which was also confirmed by PXRD. In summary, the incorporation of flavins in MOFs yields solid-state materials with enhanced rigidity, stabilized conformation, defined orientation and reduced aggregations of the flavins, leading to increased fluorescence lifetime and quantum yield as controllable photo-luminescent and photo-physical properties.