The Interaction Effect of the Design Parameters on the Water Absorption of the Hemp-Reinforced Biocarbon-Filled Bio-Epoxy Composites.

Natural fiber-reinforced composites perform poorly when exposed to moisture. Biocarbon has been proven to improve the water-absorbing behavior of natural fiber composites. However, the interaction effect of the design parameters on the biocarbon-filled hemp fiber-reinforced bio-epoxy composites has not been studied. In this study, the effects of the design parameters (pyrolysis temperature, biocarbon particle size, and filler loading) on the water absorptivity and water diffusivity of hemp-reinforced biopolymer composites have been investigated. Biocarbon from the pyrolysis of hemp and switchgrass was produced at 450, 550, and 650 °C. Composite samples with 10 wt.%, 15 wt.%, and 20 wt.% of biocarbon fillers of sizes below 50, 75, and 100 microns were used. The hemp fiber in polymer composites showed a significant influence in its water uptake behavior with the value of water absorptivity 2.41 × 10-6 g/m2.s1/2. The incorporation of biocarbon fillers in the hemp biopolymer composites reduces the average water absorptivity by 44.17% and diffusivity by 42.02%. At the optimized conditions, the value of water absorptivity with hemp biocarbon and switchgrass biocarbon fillers was found to be 0.72 × 10-6 g/m2.s1/2 and 0.73 × 10-6 g/m2.s1/2, respectively. The biocarbon at 650 °C showed the least composite thickness swelling due to its higher porosity and lower surface area. Biocarbon-filled hemp composites showed higher flexural strength and energy at the break due to the enhanced mechanical interlocking between the filler particles and the matrix materials. Smaller filler particle size lowered the composite's water diffusivity, whereas the larger particle size of the biocarbon fillers in composites minimizes the water absorption. Additionally, higher filler loading results in weaker composite tensile energy at the break due to the filler agglomeration, reduced polymer-filler interactions, reduced polymer chain mobility, and inadequate dispersion of the filler.

Effect of Adaptive Seating Systems on Postural Control and Activity Performance: A Systematic Review.

PURPOSE: To systematically review the effectiveness of adaptive seating systems on sitting posture, postural control, and seated activity performance in children with cerebral palsy (CP). SUMMARY OF KEY POINTS: From 5 databases, 3 of 21 (14%) articles were of good quality based on the Downs and Black checklist. Commercial modular contoured seating and paper-based low-cost, and contoured foam seating were effective at improving sitting posture, postural control, and seated activity performance. Parents and service providers reported that seating systems reduced stress, burden and psychosocial well-being, and quality of life in children with CP. CONCLUSION: Limited evidence demonstrated that adaptive seating systems were effective at improving sitting ability and postural control. Randomized controlled trials with objective outcome measures of seating performance in children with CP are needed to evaluate effectiveness. RECOMMENDATIONS FOR CLINICAL PRACTICE: Adaptive seating devices are preferred by parents and therapists for children with CP; however, objective measures of seating outcomes are needed.

Chemical extraction of chitin from American lobster (Homarus americanus) shells optimized through response surface methodology.

Chitin extraction from the shells of American lobsters (Homarus americanus) was optimized through the use of response surface methodology (RSM). The demineralization step was optimized to minimize the ash content of shell samples and the deproteination step was optimized to minimize the protein content of the chitin product. At a laboratory scale, one set of optimized conditions for the demineralization step was 7.35 % w/w acetic acid at a 40 mL/g of powdered lobster shell ratio for 15 min; this lowered the ash content from 39.62 % to 0.41 ± 0.08 %. A set of optimized conditions for the deproteination step at a similar scale was 4 % w/w sodium hydroxide at a 43 mL/g demineralized shell ratio heated to 95 °C for 83 min. These conditions were indicated to entirely remove protein from the resultant chitin. Average yields under optimized conditions were 23.43 ± 1.75 % for demineralization and 30.33 ± 0.02 % for deproteination, though a demineralization reaction with larger biomass input had a higher yield at 40.31 %.

Comparative study of the structure and mechanical properties of starch aerogels fabricated from air-classified and isolated pulse starches.

Significant amounts of starch and protein are generated as co-products during fractionation of pulse seeds. While pulse proteins (PP) have garnered a lot of interest in numerous applications, little attention is shown to pulse starch (PS). The creation of novel materials such as bioplastics could revolutionize the use of pulse starches. In this study, we investigated the prospects of air-classified and isolated pea, lentil, and faba bean starches as a precursor for fabricating pulse starch bioaerogels (PSBs) via freeze-drying technique. The results evidenced ultra-low densities (<0.1 m2/g), mesopore sizes (2-50 µm), high porosities (∼99 %), low surface areas (SBET = âˆ¼4-18 m2/g) for all the aerogels. The adsorption isotherm showed typical Type II and III profiles, while the thermogravimetric analysis showed more weight loss (74.39-78.12 %) in aerogels mostly developed from isolated starches. Microstructural studies showed a unique distribution of pores within the developed aerogels. FTIR and XPS studies confirmed the presence of an amide (I, II, III) at different absorption bands range (∼1600-1200 cm-1) and functional groups (carboxylic group and the amide group), respectively. All the PSBs became stiffer with a corresponding increase in load, and a reversible deformation in the linear region was identified at <5 % strain. Comparatively, saturated PSBs from air-classified starch at a relative humidity of 95 % showed a drastic reduction in their compressive moduli (CM), while PSBs from isolated starch experienced markedly high CM. Moisture saturation was achieved at 72 h for all the samples. This study provides crucial information that could spark a keen interest in the use of non-conventional starch for the creation of novel and sustainable biobased products with expanded applications.

Attempted suicide by hanging in a pregnant adolescent with psychiatric illness: A case report.

Cases of mental illnesses and suicide attempts while pregnant are of grave concern because they negatively affect both the mother and her fetus. Here we report a case of an 18-year-old woman, who was found at 35 weeks into her pregnancy. She was unconscious when her sister-in-law rescued her. Upon arrival, she was agitated and had respiratory distress. She went into spontaneous labor the next day and delivered a premature infant who succumbed within 24 h. She had a history of mental illness in the past and previous suicide attempts. The reason for her suicide stemmed from conflicts within her family and disagreement with her husband. Various psychosocial elements play a role in suicide risk, such as young age, having a history of mental health issues, experiencing trauma facing domestic violence, and dealing with financial stress. This underlines the need for mental health screening in the course of antenatal visits for a complete risk assessment.

Nanocellulose in targeted drug delivery: A review of modifications and synergistic applications.

Nanocellulose, a versatile biopolymer renowned for its exceptional physicochemical attributes including lightweight, biocompatibility, biodegradability, and higher mechanical strength properties has captured significant attention in biomedical research. This renewable material, extracted from widely abundant biosources including plants, bacteria, and algae, exists in three primary forms: cellulose-based nanocrystals (CNCs), nanofibrils (CNFs), and bacterial nanocellulose (BNC). CNCs are characterized by their highly crystalline, needle-shaped structure, while CNFs possess a blend of amorphous and crystalline regions. BNC stands out as the purest form of nanocellulose. Chemical functionalization enables precise tuning of nanocellulose properties, enhancing its suitability for diverse biomedical applications. In drug delivery systems, nanocellulose's unique structure and surface chemistry offer opportunities for targeted delivery of active molecules. Surface-modified nanocellulose can effectively deliver drugs to specific sites, utilizing its inherent properties to control drug release kinetics and improve therapeutic outcomes. Despite these advantages, challenges such as achieving optimal drug loading capacity and ensuring sustained drug release remain. Future research aims to address these challenges and explore novel applications of nano-structured cellulose in targeted drug delivery, highlighting the continued evolution of this promising biomaterial in biomedicine. Furthermore, the review delves into the impact of chemical, physical, and enzymatic methods for CNC surface modifications, showcasing how these approaches enhance the functionalization of CNCs for targeted delivery of different compounds in biological systems.

Suicide contagion and psychosocial risks among Nepali youth through a near-hanging case study.

The phenomenon of suicide contagion: some individuals, especially vulnerable young people, exhibit increased susceptibility to suicidal ideation when exposed to the suicide of other people. Significant research suggests that exposure to media portrayals, suicide groups and peer suicides may lead to suicide contagion. Prevalent psychosocial and cultural factors in Nepal such as interpersonal conflict, domestic violence, gender inequity and social exclusion probably contribute to suicidal behaviour. This case study investigates a high school student in a rural mountainous community in Nepal, who attempted suicide by hanging following his girlfriend's suicide, and demonstrates how peer suicide exposure prompts imitative behaviour in a vulnerable young person and confirms suicide grief as an underrepresented risk factor. Prompt, supportive interventions for high-risk grievers and societal prevention strategies tailored to adolescents are essential to curb imitative deaths.

Cellulose nanocrystals in the development of biodegradable materials: A review on CNC resources, modification, and their hybridization.

The escalating demand for sustainable materials has propelled cellulose into the spotlight as a promising alternative to petroleum-based products. As the most abundant organic polymer on Earth, cellulose is ubiquitous, found in plants, bacteria, and even a unique marine animal-the tunicate. Cellulose polymers naturally give rise to microscale semi-crystalline fibers and nanoscale crystalline regions known as cellulose nanocrystals (CNCs). Exhibiting rod-like structures with widths spanning 3 to 50 nm and lengths ranging from 50 nm to several microns, CNC characteristics vary based on the cellulose source. The degree of crystallinity, crucial for CNC properties, fluctuates between 49 and 95 % depending on the source and synthesis method. CNCs, with their exceptional properties such as high aspect ratio, relatively low density (≈1.6 g cm-3), high axial elastic modulus (≈150 GPa), significant tensile strength, and birefringence, emerge as ideal candidates for biodegradable fillers in nanocomposites and functional materials. The percolation threshold, a mathematical concept defining long-range connectivity between filler and polymer, governs the effectiveness of reinforcement in nanocomposites. This threshold is intricately influenced by the aspect ratio and molecular interaction strength, impacting CNC performance in polymeric and pure nanocomposite materials. This comprehensive review explores diverse aspects of CNCs, encompassing their derivation from various sources, methods of modification (both physical and chemical), and hybridization with heterogeneous fillers. Special attention is devoted to the hybridization of CNCs derived from tunicates (TCNC) with those from wood (WCNC), leveraging the distinct advantages of each. The overarching objective is to demonstrate how this hybridization strategy mitigates the limitations of WCNC in composite materials, offering improved interaction and enhanced percolation. This, in turn, is anticipated to elevate the reinforcing effects and pave the way for the development of nanocomposites with tunable viscoelastic, physicochemical, and mechanical properties.

Comparative analysis of porcine-uterine decellularization for bioactive-molecule preservation and DNA removal.

Introduction: Decellularized uterine extracellular matrix has emerged as a pivotal focus in the realm of biomaterials, offering a promising source in uterine tissue regeneration, research on disease diagnosis and treatments, and ultimately uterine transplantation. In this study, we examined various protocols for decellularizing porcine uterine tissues, aimed to unravel the intricate dynamics of DNA removal, bioactive molecules preservation, and microstructural alterations. Methods: Porcine uterine tissues were treated with 6 different, yet rigorously selected and designed, protocols with sodium dodecyl sulfate (SDS), Triton® X-100, peracetic acid + ethanol, and DNase I. After decellularization, we examined DNA quantification, histological staining (H&E and DAPI), glycosaminoglycans (GAG) assay, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and Thermogravimetric Analysis (TGA). Results: A comparative analysis among all 6 protocols was conducted with the results demonstrating that all protocols achieved decellularization; while 0.1% SDS + 1% Triton® X-100, coupled with agitation, demonstrated the highest efficiency in DNA removal. Also, it was found that DNase I played a key role in enhancing the efficiency of the decellularization process by underscoring its significance in digesting cellular contents and eliminating cell debris by 99.79% (19.63 ± 3.92 ng/mg dry weight). Conclusions: Our findings enhance the nuanced understanding of DNA removal, GAG preservation, microstructural alteration, and protein decomposition in decellularized uterine extracellular matrix, while highlighting the importance of decellularization protocols designed for intended applications. This study along with our findings represents meaningful progress for advancing the field of uterine transplantation and related tissue engineering/regenerative medicine.

Development of Polylactic Acid Films with Alkali- and Acetylation-Treated Flax and Hemp Fillers via Solution Casting Technique.

This study aims to enhance value addition to agricultural byproducts to produce composites by the solution casting technique. It is well known that PLA is moisture-sensitive and deforms at high temperatures, which limits its use in some applications. When blending with plant-based fibers, the weak point is the poor filler-matrix interface. For this reason, surface modification was carried out on hemp and flax fibers via acetylation and alkaline treatments. The fibers were milled to obtain two particle sizes of <75 µm and 149-210 µm and were blended with poly (lactic) acid at different loadings (0, 2.5%, 5%, 10%, 20%, and 30%) to form a composite film The films were characterized for their spectroscopy, physical, and mechanical properties. All the film specimens showed C-O/O-H groups and the π-π interaction in untreated flax fillers showed lignin phenolic rings in the films. It was noticed that the maximum degradation temperature occurred at 362.5 °C. The highest WVPs for untreated, alkali-treated, and acetylation-treated composites were 20 × 10-7 g·m/m2 Pa·s (PLA/hemp30), 7.0 × 10-7 g·m/m2 Pa·s (PLA/hemp30), and 22 × 10-7 g·m/m2 Pa·s (PLA/hemp30), respectively. Increasing the filler content caused an increase in the color difference of the composite film compared with that of the neat PLA. Alkali-treated PLA/flax composites showed significant improvement in their tensile strength, elongation at break, and Young's modulus at a 2.5 or 5% filler loading. An increase in the filler loadings caused a significant increase in the moisture absorbed, whereas the water contact angle decreased with an increasing filler concentration. Flax- and hemp-induced PLA-based composite films with 5 wt.% loadings showed a more stable compromise in all the examined properties and are expected to provide unique industrial applications with satisfactory performance.

Crosslinked poly (vinyl alcohol) composite reinforced with tunicate, wood, and hybrid cellulose nanocrystals: Comparative physicochemical, thermal, and mechanical properties.

The development of sustainable and biodegradable composites has gained increasing attention in recent years. Effective interaction and adhesion between polymers and fillers are crucial. In this study, the effect of different aspect ratios of cellulose nanocrystals (CNCs) and their hybrid within a crosslinked poly (vinyl alcohol) (PVA) nanocomposite has been investigated to develop biodegradable materials. The physicochemical, thermal, and mechanical properties of the specimens have been studied. SEM images indicate that the addition of CNC reduced the porosity of the films. The XPS results confirmed the significant formation of covalent bonds for all composites except those reinforced with wood-CNC, which showed a lower amount of crosslinking and CC formation. EDS maps reveals that the dispersity of the CNCs could be different depending on the aspect ratio of the CNCs. Results from the solubility in water (SW) tests indicated that the use of hybrid-CNC in a crosslinked system decreased the SW significantly. The crosslinking and addition of CNC to the PVA composite led to improved mechanical properties. Elongation at break (EB) decreased significantly for the crosslinked hybrid-CNC nanocomposite. Overall, the results of this study indicate that the aspect ratio of CNCs as fillers in nanocomposites may contribute to their physicochemical, mechanical, and thermal properties for the development of biodegradable materials.

Thermal Response of Biocarbon-Filled Hemp Fiber-Reinforced Bioepoxy Composites.

We investigated the thermal conductivity of materials based on pyrolysis temperature, filler loading, filler size, and type of biomass feedstock. Hemp stalk and switchgrass were pyrolyzed at 450, 550, and 650 °C and crushed into 50, 75, and 100 µm particle sizes. Biocarbon fillers (10, 15, and 20 wt %) were added to the bioepoxy polymer matrix. The study showed increased filler loading and particle size increased thermal conductivity-the biocomposite samples with 20 wt % filler loading of 100 µm particle size of the biocarbon obtained at 650 °C showed the maximum thermal conductivity in both hemp biocarbon-filled composites (0.59 W·m-1·K-1) and switchgrass-filled composites (0.58 W·m-1·K-1) with the highest flame time. Biocarbon in biofiber-reinforced polymer composites can improve thermal conductivity and extend the flame time. These findings significantly contribute to developing hemp-based bioepoxy composite materials for thermal applications in various fields. These include insulating materials for buildings and thermal management systems, energy-efficient applications, and help in material selection and product design with a positive environmental impact.

Enhancing the Potential of Polymer Composites Using Biochar as a Filler: A Review.

This article discusses the scope biochar's uses; biochar is a sustainable organic material, rich in carbon, that can be synthesized from various types of biomass feedstock using thermochemical reactions such as pyrolysis or carbonization. Biochar is an eco-friendly filler material that can enhance polymer composites' mechanical, thermal, and electrical performances. In comparison to three inorganic fillers, namely carbon black, carbon nanotubes (CNT), and carbon filaments, this paper explores the optimal operating conditions for regulating biochar's physical characteristics, including pore size, macro- and microporosity, and mechanical, thermal, and electrical properties. Additionally, this article presents a comparative analysis of biochar yield from various thermochemical processes. Moreover, the review examines how the surface functionality, surface area, and particle size of biochar can influence its mechanical and electrical performance as a filler material in polymer composites at different biochar loads. The study showcases the outstanding properties of biochar and recommends optimal loads that can improve the mechanical, thermal, and electrical properties of polymer composites.

Chitin, Chitosan, and Nanochitin: Extraction, Synthesis, and Applications.

Crustacean shells are a sustainable source of chitin. Extracting chitin from crustacean shells is ongoing research, much of which is devoted to devising a sustainable process that yields high-quality chitin with minimal waste. Chemical and biological methods have been used extensively for this purpose; more recently, methods based on ionic liquids and deep eutectic solvents have been explored. Extracted chitin can be converted into chitosan or nanochitin. Once chitin is obtained and modified into the desired form, it can be used in a wide array of applications, including as a filler material, in adsorbents, and as a component in biomaterials, among others. Describing the extraction of chitin, synthesis of chitosan and nanochitin, and applications of these materials is the aim of this review. The first section of this review summarizes and compares common chitin extraction methods, highlighting the benefits and shortcomings of each, followed by descriptions of methods to convert chitin into chitosan and nanochitin. The second section of this review discusses some of the wide range of applications of chitin and its derivatives.

Multilayer photonic films based on interlocked chiral-nematic cellulose nanocrystals in starch/chitosan.

In this study, a new approach to employ and control cellulose nanocrystal (CNC) chiral nematic structure as a biodegradable, intelligent material was investigated. Tuned CNC self-assembled films were interlocked between two layers of citric acid, cross-linked starch/chitosan (1:1) films through the solvent casting process. This method increased the mechanical properties of produced films and created a selective reflection band from UV to near-IR depending on the helical pitch of the chiral nematic CNC layer. The features of these intelligent films have potential for different applications, from UV protective packaging to biomedical uses. The water vapor permeability (WVP) of the produced films decreased considerably by adding a CNC layer into the cross-linked starch/chitosan structure. Also, the WVP was different for the different helical pitches of the CNC layer. The starch/chitosan (outer layer) also showed a remarkable antibacterial property against E. coli, P. fluorescens, S. Enteritidis, and S. aureus which could be useful for biomedical applications or antibacterial packaging.

Comparison of Protein Content, Availability, and Different Properties of Plant Protein Sources with Their Application in Packaging.

Plant-based proteins are considered to be one of the most promising biodegradable polymers for green packaging materials. Despite this, the practical application of the proteins in the packaging industry on a large scale has yet to be achieved. In the following review, most of the data about plant protein-based packaging materials are presented in two parts. Firstly, the crude protein content of oilseed cakes and meals, cereals, legumes, vegetable waste, fruit waste, and cover crops are indexed, along with the top global producers. In the second part, we present the different production techniques (casting, extrusion, and molding), as well as compositional parameters for the production of bioplastics from the best protein sources including sesame, mung, lentil, pea, soy, peanut, rapeseed, wheat, corn, amaranth, sunflower, rice, sorghum, and cottonseed. The inclusion of these protein sources in packaging applications is also evaluated based on their various properties such as barrier, thermal, and mechanical properties, solubility, surface hydrophobicity, water uptake capacity, and advantages. Having this information could assist the readers in exercising judgement regarding the right source when approving the applications of these proteins as biodegradable packaging material.

Valorization of Starch to Biobased Materials: A Review.

Many concerns are being expressed about the biodegradability, biocompatibility, and long-term viability of polymer-based substances. This prompted the quest for an alternative source of material that could be utilized for various purposes. Starch is widely used as a thickener, emulsifier, and binder in many food and non-food sectors, but research focuses on increasing its application beyond these areas. Due to its biodegradability, low cost, renewability, and abundance, starch is considered a "green path" raw material for generating porous substances such as aerogels, biofoams, and bioplastics, which have sparked an academic interest. Existing research has focused on strategies for developing biomaterials from organic polymers (e.g., cellulose), but there has been little research on its polysaccharide counterpart (starch). This review paper highlighted the structure of starch, the context of amylose and amylopectin, and the extraction and modification of starch with their processes and limitations. Moreover, this paper describes nanofillers, intelligent pH-sensitive films, biofoams, aerogels of various types, bioplastics, and their precursors, including drying and manufacturing. The perspectives reveal the great potential of starch-based biomaterials in food, pharmaceuticals, biomedicine, and non-food applications.

Precise quantum measurement of vacuum with cold atoms.

We describe the cold-atom vacuum standards (CAVS) under development at the National Institute of Standards and Technology (NIST). The CAVS measures pressure in the ultra-high and extreme-high vacuum regimes by measuring the loss rate of sub-millikelvin sensor atoms from a magnetic trap. Ab initio quantum scattering calculations of cross sections and rate coefficients relate the density of background gas molecules or atoms to the loss rate of ultra-cold sensor atoms. The resulting measurement of pressure through the ideal gas law is traceable to the second and the kelvin, making it a primary realization of the pascal. At NIST, two versions of the CAVS have been constructed: a laboratory standard used to achieve the lowest possible uncertainties and pressures, and a portable version that is a potential replacement for the Bayard-Alpert ionization gauge. Both types of CAVSs are connected to a combined extreme-high vacuum flowmeter and dynamic expansion system to enable sensing of a known pressure of gas. In the near future, we anticipate being able to compare the laboratory scale CAVS, the portable CAVS, and the flowmeter/dynamic expansion system to validate the operation of the CAVS as both a standard and vacuum gauge.

Healthcare Professionals Providing Direct Care to the COVID-19 Patients: A Descriptive Cross-sectional Study.

INTRODUCTION: COVID-19 highly contagious viruses that have reached every corner of the world. Despite the heroic efforts to control the pandemic, health care professional risk for COVID-19 exposure was an important measure to identify due to lack of personal protective equipment. The objective of the study was to find out the prevalence of healthcare professionals providing direct care to the COVID-19 patient. METHODS: A descriptive cross-sectional was conducted through online questionnaire from June 2020 to August 2020. Ethical approval was obtained from the Ethical Review Board of Nepal Health Research Council (Reference number: 363/2020 P). World Health Organization risk assessment protocol questionnaire was used for COVID-19 and distributed among 300 health care workers of Nepal involved in the management of COVID-19 hospitals. Convenience sampling was used. The KoBo toolbox was used for online data collection. Data analysis was done using Statistical Package for the Social Sciences version 23. Point estimate at 95% Confidence Interval was calculated along with frequency and percentage for binary data. RESULTS: Among 300 study participants, 109 (36.33%), (30.85-41.74 at 95% Confidence Interval) of participants provide direct care to infected patients. With total respondents, 41 (37.61%) were registered nurses, medical doctors 28 (25.68%) and paramedics 36 (33.02%). CONCLUSIONS: Health care workers who provide direct care to the COVID-19 patient were similar to other studies done in similar settings. About half of the participants were exposed to COVID-19 virus from the hospital setting rather than from community setting which is similar to the study done in similar setting which might be due to lack of follow of protocols during COVID-19 patient care.

Wildlife in climate refugia: Mammalian diversity, occupancy, and tiger distribution in the Western Himalayas, Nepal.

Anthropogenic land-use change continues to be predicated as a major driver of terrestrial biodiversity loss for the rest of this century. It has been determined that the effect of climate change on wildlife population will accelerate the rate and process of decline of global vertebrate populations. We investigated wildlife composition, occupancy, and activity pattern along the larger climate resilient forests that serve as microrefugia for a wide range of species under the escalating climate change. We used camera trap survey covering 250 km2 of climate microrefugia in Dadeldhura hills in far western region of Nepal. We used 62 trapping locations accumulating 1800 trap nights taking 98,916 photographs in 62 days-survey period during the summer season of 2020. We photographed 23 mammalian species with estimated species richness of 30 species (95% CI: 25-34) based on multi-species occupancy model. We estimated overall species occupancy ψ(SE(ψ)) to be 0.87 (0.09) in climatic microrefugia. While human activity predominated throughout the day, the majority of animals was found to exhibit nocturnal temporal patterns. Tiger and hyaena, two of the top predators, were newly discovered in the western Himalayan range of Nepal, with their discovery at the 34 highest elevations of 2511 meters and 2000m, respectively. In Nepal, high-altitude tiger range is characterized by tiger distribution above a 2000 m cutoff representing habitats in the physiographic zone of high mountains and above. Our findings establish a baseline and show that the climatic microrefugia that have been identified have high levels of species richness and occupancy, which characterize the Dadeldhura hill forest ranges as biologically varied and ecologically significant habitat. These areas identified as climatic microrefugia habitats should be the focus of conservation efforts, particularly efforts to reduce human disturbance and adapt to climate change.