Date palm-magnetized biochar for in-situ stabilization of toxic metals in mining-polluted soil: evaluation using single-step extraction methods and phytoavailability.

Mining activities provide a pathway for the entry and accumulation of various heavy metals in soil, which ultimately leads to severe environmental pollution. Utilization of various immobilizing agents could restore such contaminated soils. Therefore, in this study, date palm-derived biochars (BCs: produced at 300 °C, 500 °C and 700 °C) and magnetized biochars (MBCs) were employed to stabilize heavy metals (Cd, Pb, Cu and Zn) in mining polluted soil. Metal polluted soil was amended with BCs and MBCs at w/w ratio of 2% and cultivated with wheat (Triticum aestivum L.) in a greenhouse. After harvesting, dry and fresh biomass of plants were recorded. The soil and plant samples were collected, and the concentrations of heavy metals were measured after extracting with water, DTPA (diethylenetriaminepentaacetic acid), EDTA (ethylenediaminetetraacetic acid), and acetic acid. BCs and MBCs resulted in reduced metal availability and uptake, with higher fresh and dry biomass (>36%). MBCs showed maximum decrease (>70%) in uptake and shoot concentration of metals, as these reductions for Cd and Pb reached below the detection limits. Among all single-step extractions, the DTPA-extractable metals showed a significant positive correlation with shoot concentrations of tested metals. Thus, the synthesized BCs and MBCs could effectively be used for stabilizing heavy metals and improve plant productivity in multi-contaminated soils. However, future studies should focus on long term field trials to restore contaminated mining soils using modified biochars.

This study has demonstrated the performance of magnetized biochars for in-situ stabilization of toxic metals (Cd, Pb, Cu and Zn) in mining polluted soil by single extraction method. All the produced BCs and magnetized BCs showed great potential in immobilizing the metals and reducing their availability in soil, consequently decreasing their shoot concentration and plant uptake. Significant negative correlations were observed between soil pH and metal extraction from applied extraction methods such as water soluble, DTPA, and EDTA extractions. We found DTPA as a suitable extractant for investigating metal uptake in plant in multi-contaminated soils. Treatments with MBCs showed maximum decrease in plant uptake and concentration of studied metals. Thus, application of MBCs could efficiently immobilize soil heavy metals.

Prevalence of human pathogenic viruses in wastewater: A potential transmission risk as well as an effective tool for early outbreak detection for COVID-19.

Millions of human pathogenic viral particles are shed from infected individuals and introduce into wastewater, subsequently causing waterborne diseases worldwide. These viruses can be transmitted from wastewater to human beings via direct contact and/or ingestion/inhalation of aerosols. Even the advanced wastewater treatment technologies are unable to remove pathogenic viruses from wastewater completely, posing a serious health risk. Recently, coronavirus disease 2019 (COVID-19) has been urged globally due to severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2), which has resulted in >4.1 million deaths until July 2021. A rapid human-to-human transmission, uncertainties in effective vaccines, non-specific medical treatments, and unclear symptoms compelled the world into complete lockdown, social distancing, air-travel suspension, and closure of educational institutions, subsequently damaging the global economy and trade. Although, few medical treatments, rapid detection tools, and vaccines have been developed so far to curb the spread of COVID-19; however, several uncertainties exist in their applicability. Further, the acceptance of vaccines among communities is lower owing to the fear of side effects such as blood-clotting and heart inflammation. SARS-CoV-2, an etiologic agent of COVID-19, has frequently been detected in wastewater, depicting a potential transmission risk to healthy individuals. Contrarily, the occurrence of SARS-CoV-2 in wastewater can be used as an early outbreak detection tool via water-based epidemiology. Therefore, the spread of SARS-CoV-2 through fecal-oral pathway can be reduced and any possible outbreak can be evaded by proper wastewater surveillance. In this review, wastewater recycling complications, potential health risks of COVID-19 emergence, and current epidemiological measures to control COVID-19 spread have been discussed. Moreover, the viability of SARS-CoV-2 in various environments and survival in wastewater has been reviewed. Additionally, the necessary actions (vaccination, face mask, social distancing, and hand sanitization) to limit the transmission of SARS-CoV-2 have been recommended. Therefore, wastewater surveillance can serve as a feasible, efficient, and reliable epidemiological measure to lessen the spread of COVID-19.

Sulfamethoxazole Leaching from Manure-Amended Sandy Loam Soil as Affected by the Application of Jujube Wood Waste-Derived Biochar.

Vertical translocation/leaching of sulfamethoxazole (SMZ) through manure-amended sandy loam soil and significance of biochar application on SMZ retention were investigated in this study. Soil was filled in columns and amended with manure spiked with 13.75 mg kg-1 (S1), 27.5 mg kg-1 (S2), and 55 mg kg-1 (S3) of SMZ. Jujube (Ziziphus jujube L.) wood waste was transformed into biochar and mixed with S3 at 0.5% (S3-B1), 1.0% (S3-B2), and 2.0% (S3-B3) ratio. Cumulative SMZ leaching was lowest at pH 3.0, which increased by 16% and 34% at pH 5.0 and 7.0, respectively. A quicker release and translocation of SMZ from manure occurred during the initial 40 h, which gradually reduced over time. Intraparticle diffusion and Elovich kinetic models were the best fitted to leaching data. S3 exhibited the highest release and vertical translocation of SMZ, followed by S2, and S1; however, SMZ leaching was reduced by more than twofold in S3-B3. At pH 3.0, 2.0% biochar resulted in 99% reduction in SMZ leaching within 72 h, while 1.0% and 0.5% biochar applications reduced SMZ leaching to 99% within 120 and 144 h, respectively, in S3. The higher SMZ retention onto biochar could be due to electrostatic interactions, H-bonding, and π-π electron donor acceptor interactions.

Effects of pyrolysis temperature on nitrate-nitrogen (NO3--N) and bromate (BrO3-) adsorption onto date palm biochar.

Biochars (BCs) produced through biomass pyrolysis are highly efficient adsorbents for retaining dissolved cations in soil and water. However, their anionic sorption characteristics are unclear and depend on the feedstock used and the pyrolysis temperature. Herein, the adsorption of nitrate-nitrogen (NO3--N) and bromate (BrO3-) anions onto date palm biochar was evaluated by considering the pyrolysis temperature in relation with the initial concentrations, initial pH, and adsorbent dose. Biochars from date palm rachis were produced at 300 °C (BC300) and 700 °C (BC700). The latter exhibited the highest adsorption efficiency of NO3--N from aqueous solutions at an initial pH of 2, which was 25.8%-44.3% (at an adsorbent dose of 4 g L-1) and 47.0%-73.0% (at an adsorbent dose of 10 g L-1). In contrast, BC300 adsorbed BrO3- with an adsorption efficiency of 19.3%, 14.5%, 14.9%, and 13.6% at initial added concentrations of 5, 10, 15, and 20 µg L-1, respectively. However, BC700 showed zero adsorption for BrO3-. The results also showed that the non-linear models of Langmuir and/or Freundlich for NO3--N and BrO3- adsorption described the adsorption data better in most cases. It could be concluded that high pyrolysis temperature BC are suitable for adsorbing NO3--N, and low pyrolysis temperature BC may be used to adsorb BrO3-.

A critical review on organic micropollutants contamination in wastewater and removal through carbon nanotubes.

The prevalence of organic micropollutants (OMPs) in various environmental compartments is posing a serious health risks to all kinds of lives on the planet. The levels of OMPs such as polyaromatic hydrocarbons, antibiotics, pesticides, contraceptive medicines, and personal care products in water bodies are increasing with each passing day. It is an urgent need of time to limit the release of OMPs into the environment, and to remove the prevailing OMPs for sustainable environmental management. The majority of the conventional means of water decontamination are either inefficient or expensive. However, due to nanosize, high surface area, and hollow and layered structure, carbon nanotubes (CNTs) serve as excellent sorbents for the removal of a diverse range of OMPs. The occurrence of emerging OMPs and their detrimental effects on human and animal health are collected and discussed in this review. The characteristics and efficacy of various CNTs (pristine and modified) for the efficient removal of different OMPs, and the removal mechanisms have been reviewed and discussed. The literature demonstrated that adsorption of OMPs onto CNTs is very complicated and rely on multiple factors including the properties of adsorbent and the adsorbate as well as solution chemistry. It was found that H-bonding, electrostatic interactions, van der Waals forces, hydrophobic interactions, H-π bongs, and π-π interactions were the major mechanisms responsible for the adsorption of OMPs onto various kinds of CNTs. Despite of higher affinities for OMPs, hydrophobicity and higher costs restrain the practical application of CNTs for wastewater treatment on large scale. However, continuous production may lead to the development of cost-effective, efficient and eco-friendly CTNs technology for wastewater treatments in future.

Date palm waste-derived biochar composites with silica and zeolite: synthesis, characterization and implication for carbon stability and recalcitrant potential.

Engineered organo-mineral composites were synthesized from date palm waste biochar and silica or zeolite via mechanochemical treatments. Date palm tree rachis (leaves) waste biomass was pre-treated with silica or zeolite minerals via ball milling and sonication prior to pyrolysis at 600 °C. The resultant organo-mineral composites and pristine materials were characterized using X-ray diffraction, thermogravimetric-differential thermal (TG-DTA), Fourier transform infrared, scanning electron microscope analyses and surface area and porosity analyzer to investigate the variations in physiochemical and structural characteristics. Compared to the resultant composites derived from non-milled date palm biomass, ball milling increased surface area, while decreased crystallinity index and effective particle size of the biochar composites. Silica composited biochars were located near origin in the van Krevelen diagram indicating lowest H/C and O/C molar ratios, thus suggesting higher aromaticity and lower polarity compared to other biochars. TGA thermograms indicated highest thermal stability of silica composited biochars. Ash and moisture corrected TGA thermograms were used to calculate recalcitrance index (R50) of the materials, which speculated high degradability of biomass (R50 < 0.4), minimal degradability of biochars and zeolite composited biochars (0.5 < R50 < 0.7) and high recalcitrant nature of silica composited biochars (R50 > 0.7). Silica composited biochars exhibited highest carbon sequestration potential (64.17-95.59%) compared to other biochars. Highest recalcitrance and carbon sequestration potential of silica composited biochars may be attributed to changes in structural arrangements in the silica-biochar complex. Encapsulations of biochar particles with amorphous silica via Si-C bonding may have prevented thermal degradation, subsequently increasing recalcitrance potential of silica composited biochars.

Correction to: Date palm waste-derived biochar composites with silica and zeolite: synthesis, characterization and implication for carbon stability and recalcitrant potential.

Unfortunately, in the original publication of the article, Prof. Yong Sik Ok's affiliation was incorrectly published.

Date palm waste biochars alter a soil respiration, microbial biomass carbon, and heavy metal mobility in contaminated mined soil.

A 30-day incubation experiment was conducted using a heavy metal-contaminated mined soil amended with date palm feedstock (FS) and its derivative biochars (BCs) at three pyrolysis temperatures of 300 (BC-300), 500 (BC-500), and 700 °C (BC-700) with different application rates (0.0, 5, 15, and 30 g kg-1) to investigate their short-term effects on soil respiration (CO2-C efflux), microbial biomass carbon (MBC), soil organic carbon (SOC), mobile fraction of heavy metals (Cd, Cu, Pb, Zn, Mn, and Fe), pH, and electrical conductivity (EC). The results showed that FS and BC-300 with increasing addition rate significantly reduced soil pH, whereas SOC, CO2-C efflux, and soil MBC were increased compared to the control. On the contrary, BC-500 and BC-700 increased soil pH at early stage of incubation and have small or no effects on SOC, CO2-C efflux, and MBC. Based on the results, the date palm biochars exhibited much lower cumulative CO2-C efflux than feedstock, even with low-temperature biochar, indicating that BCs have C sequestration potential. Applying BC-700 at 15 and 30 g kg-1 significantly reduced cumulative CO2-C efflux by 21.8 and 45.4% compared to the control, respectively. The incorporation of FS into contaminated soil significantly increased the mobile content of Cd and Mn, but decreased the mobile content of Cu. However, BC-300 significantly reduced the mobile content of Cd, Cu, Pb, and Zn. It could be concluded that low-temperature biochar could be used as a soil amendment for reducing heavy metal mobility in mining contaminated soil in addition to minimize soil CO2-C efflux.

Correction to: Date palm waste biochars alter a soil respiration, microbial biomass carbon, and heavy metal mobility in contaminated mined soil.

Unfortunately, in the original publication of the article, Prof. Yang Sik Ok's affiliation was incorrectly published. The author's affiliation is as follows.

A comparison of two digestion methods for assessing heavy metals level in urban soils influenced by mining and industrial activities.

A comparison between two digestion methods of hot plate Hossner (total-total) and USEPA method 3051 (total-recoverable) was carried out to suggest a proper method for determining nine heavy metals (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn) content of three urban soils affected by mining (Mahd AD'Dahab) or industrial activities (Riyadh and Jubail) at Saudi Arabia. The results showed no significant differences between two digestion methods for Cd, Cu, Pb and Zn in soils affected by mining and for Cr, Cu, Pb and Zn in soils affected by industrial activities. Additionally, lower biases were obtained between two methods for metals Cd, Cu, Zn and Pb in the urban soil samples from mining area with the percent biases of -16.5%, +6.24%, -12.4% and +24.1%, respectively. The results also revealed that only Cu and Zn in the soil samples from Riyadh were extracted satisfactorily using USEPA 3051 with low biases of +5.69% and -9.61%, respectively. Meanwhile, only Pb in soil samples from Jubail showed lower baise between two methods with satisfactory biase of -8.07%. The correlation coefficients were significant between total-recoverable and total-total concentrations for Cu (r = 0.66), Pb (r = 0.72) and Cd (r = 0.65) in soil samples from mining area. Overall, concentrations of Co, Cr, Fe, Mn, and Ni that may show soil background concentrations were found higher by Hossner method than by USEPA 3051; thus, this suggests the addition of hydrofluoric acid (HF) is necessary for the determination of lithogenic metal concentrations. It could be concluded that the USEPA 3051 may be recommended and applied for total Cd, Cu, Pb and Zn originated from anthropogenic source in mining and industrial areas.

Correction to: Determining soil quality in urban agricultural regions by soil enzyme-based index.

Unfortunately, in the original publication of the article, Prof. Yang Sik Ok's affiliation was incorrectly published. The author's affiliation is as follows.

Determining soil quality in urban agricultural regions by soil enzyme-based index.

Urban agricultural soils are highly variable, and careful selection of sensitive indicators is needed for the assessment of soil quality. This study is proposed to develop an index based on soil enzyme activities for assessing the quality of urban agricultural soils. Top soils were collected from urban agricultural areas of Korea, and soil chemical properties, texture, microbial fatty acids, and enzyme activities were determined. The soils belonged to five textural classes with the highest frequency of sandy loam. There was no clear correlation between the soil chemical properties and soil microbial properties. Principal component analysis (PCA) and factor analysis were applied to microbial groups for identification of microbial community variation in soils. Two soil groups, namely group 1 (G1) and group 2 (G2), based on microbial community abundance were examined by PCA, and those were more prominent in factor analysis. The G1 soils showed higher microbial community abundance than G2 soils. The canonical discriminant analysis was applied to the enzyme activities of sandy loam soil to develop an index, and the index validation was confirmed using the unused soils and published data. The high-quality soils in published literature assigned the high valued index. Microbial fatty acids and soil enzyme activities can be suitable indicators for soil quality evaluation of urban agricultural soils.

Trace metal levels, sources, and ecological risk assessment in a densely agricultural area from Saudi Arabia.

The present study was conducted in one of the most densely cultivated area of Al-Qassim region in Kingdom of Saudi Arabia to (i) monitor trace metal (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) contents in surface and subsurface soils, (ii) assess the pollution and potential ecological risk levels of trace metals, and (iii) identify trace metal sources using enrichment factor (EF), correlation matrix, and principal component analysis (PCA). The pollution levels of the analyzed trace metals calculated by the geoaccumulation index (I geo) and contamination factor (C f) suggested that the soils were highly contaminated with Cd and moderately contaminated with Pb. Based on the average values of EF, soil samples were found to present extremely high enrichment for Cd, significant enrichment for Pb, moderate enrichment for Zn, and deficient to minimal enrichment for other trace metals. Among the analyzed trace metals, a very high ecological risk was observed only in the case of Cd at some sampling sites. Meanwhile, other investigated trace metals had a low ecological risk. The results of PCA combined with correlation matrix suggested that Fe, Mn, Zn, Cu, Cr Ni, Cu, and Co represent natural abundance in soil, but Cd, Pb, and Cu are of anthropogenic inputs, mainly due to agrochemical and fertilizer applications. It could be generally concluded that the obtained results can be useful for assessing and conducting a future program for trace metal monitoring in agricultural areas of Saudi Arabia.

Cadmium minimization in wheat: A critical review.

Cadmium (Cd) accumulation in wheat (Triticum aestivum L.) and its subsequent transfer to food chain is a major environmental issue worldwide. Understanding wheat response to Cd stress and its management for aiming to reduce Cd uptake and accumulation in wheat may help to improve wheat growth and grain quality. This paper reviewed the toxic effects, tolerance mechanisms, and management of Cd stress in wheat. It was concluded that Cd decreased germination, growth, mineral nutrients, photosynthesis and grain yield of wheat and plant response to Cd toxicity varies with cultivars, growth conditions and duration of stress applied. Cadmium caused oxidative stress and genotoxicity in wheat plants. Stimulation of antioxidant defense system, osmoregulation, ion homeostasis and over production of signalling molecules are important adaptive strategies of wheat under Cd stress. Exogenous application of plant growth regulators, inorganic amendments, proper fertilization, silicon, and organic, manures and biochar, amendments are commonly used for the reduction of Cd uptake in wheat. Selection of low Cd-accumulating wheat cultivars, crop rotation, soil type, and exogenous application of microbes are among the other agronomic practices successfully employed in reducing Cd uptake by wheat. These management practices could enhance wheat tolerance to Cd stress and reduce the transfer of Cd to the food chain. However, their long-term sustainability in reducing Cd uptake by wheat needs further assessment.

Impact of soybean stover- and pine needle-derived biochars on Pb and As mobility, microbial community, and carbon stability in a contaminated agricultural soil.

Biochar is gaining attention as a potential soil amendment to remediate and revitalize the contaminated soils. Simultaneous effects of biochar on metals mobility, microbial abundance, bacterial diversity and carbon storage in soil are scarcely addressed. This study assessed the effect of biochars on metal mobility, microbial abundance, bacterial community, and carbon storage in an agricultural soil contaminated with heavy metals. Biochars derived from soybean stover at 300 and 700 °C (S-BC300 and S-BC700, respectively) and pine needles at the same temperatures (P-BC300 and P-BC700, respectively) were used. A maximum reduction of Pb mobility by 95% was observed from a soil treated with S-BC700, associated with precipitation of chloropyromorphite and hydroxylpyromorphite. In contrast, As was desorbed from soil particles because of P competition. The abundance of Gram-positive and negative bacteria, fungi, actinomycetes, and arbuscular mycorrhizal fungi increased in the soils treated with biochar produced at 300 °C, possibly due to the high dissolved organic and active organic carbons. Microbial abundance in the soils treated with S-BC700 and P-BC700 was constant due to the existence of fixed or non-labile carbon. Changes to bacterial communities in the biochar-treated soils depended on feedstock type and pyrolysis temperature. Actinobacteria substantially increased whereas Acidobacteria and Chloroflexi decreased in the biochar-treated soils. The non-labile carbon fraction was ∼25 fold higher in the biochar-treated soil than the control soil, indicating long-term carbon storage.

Chemically modified biochar produced from conocarpus waste increases NO3 removal from aqueous solutions.

Biochar has emerged as a universal sorbent for the removal of contaminants from water and soil. However, its efficiency is lower than that of commercially available sorbents. Engineering biochar by chemical modification may improve its sorption efficiency. In this study, conocarpus green waste was chemically modified with magnesium and iron oxides and then subjected to thermal pyrolysis to produce biochar. These chemically modified biochars were tested for NO3 removal efficiency from aqueous solutions in batch sorption isothermal and kinetic experiments. The results revealed that MgO-biochar outperformed other biochars with a maximum NO3 sorption capacity of 45.36 mmol kg(-1) predicted by the Langmuir sorption model. The kinetics data were well described by the Type 1 pseudo-second-order model, indicating chemisorption as the dominating mechanism of NO3 sorption onto biochars. Greater efficiency of MgO-biochar was related to its high specific surface area (391.8 m(2) g(-1)) and formation of strong ionic complexes with NO3. At an initial pH of 2, more than 89 % NO3 removal efficiency was observed for all of the biochars. We conclude that chemical modification can alter the surface chemistry of biochar, thereby leading to enhanced sorption capacity compared with simple biochar.

Identification, Quantification, and Toxicity of PCDDs and PCDFs in Soils from Industrial Areas in the Central and Eastern Regions of Saudi Arabia.

This study was conducted to identify and quantify polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in soil samples collected from selected industrial areas in the central and eastern regions of Saudi Arabia. All the investigated compounds of PCDDs/PCDFs were identified in the studied locations. The average concentrations of PCDDs (sum of seven congeners measured) ranged from 11.5 to 59.6 pg g(-1), with a maximum concentration of 125.7 pg g(-1) at an oil refinery station followed by 100.9 pg g(-1) at a cement factory. The average concentrations of PCDFs (sum of 10 congeners measured) accounted for 11.68-19.35 pg g(-1), with a maximum concentration of 38.67 pg g(-1) at the cement factory. It was generally observed that the soil samples collected from industrial areas have substantially high toxicity equivalence (TEQ) values of PCDDs/PCDFs compared to soils of remote areas. Principal component analysis revealed that the cement factories and oil refineries were the primary sources of PCDDs and PCDFs.

Impacts of kaolinite enrichment on biochar and hydrochar characterization, stability, toxicity, and maize germination and growth.

In this study, biochar (BC) and hydrochar (HC) composites were synthesized with natural kaolinite clay and their properties, stability, carbon (C) sequestration potential, polycyclic aromatic hydrocarbons (PAHs) toxicity, and impacts on maize germination and growth were explored. Conocarpus waste was pretreated with 0%, 10%, and 20% kaolinite and pyrolyzed to produce BCs (BC, BCK10, and BCK20, respectively), while hydrothermalized to produce HCs (HC, HCK10, and HCK20, respectively). The synthesized materials were characterized using X-ray diffraction, scanning electron microscope analyses, Fourier transform infrared, thermogravimetric analysis, surface area, proximate analyses, and chemical analysis to investigate the distinction in physiochemical and structural characteristics. The BCs showed higher C contents (85.73-92.50%) as compared to HCs (58.81-61.11%). The BCs demonstrated a higher thermal stability, aromaticity, and C sequestration potential than HCs. Kaolinite enriched-BCs showed the highest cation exchange capacity than pristine BC (34.97% higher in BCK10 and 38.04% higher in BCK20 than pristine BC), while surface area was the highest in kaolinite composited HCs (202.8% higher in HCK10 and 190.2% higher in HCK20 than pristine HC). The recalcitrance index (R50) speculated a higher recalcitrance for BC, BCK10, and BCK20 (R50 > 0.7), minimal degradability for HCK10 and HCK20 (0.5 < R50 < 0.7), and higher degradability for biomass and HC (R50 < 0.5). Overall, increasing the kaolinite enrichment percentage significantly enhanced the thermal stability and C sequestration potential of charred materials, which may be attributed to changes in the structural arrangements. The ∑ total PAHs concentration in the synthesized materials were below the USEPA's suggested limits, indicating their safe use as soil amendments. Germination indices reflected positive impacts of synthesized charred materials on maize germination and growth. Therefore, we propose that kaolinite-composited BCs and HCs could be considered as efficient and cost-effective soil amendments for improving plant growth.

Scavenging microplastics and heavy metals from water using jujube waste-derived biochar in fixed-bed column trials.

Extensive production and utilization of plastic products have resulted in the generation of microplastics (MPs), subsequently polluting the environment. The efficiency of biochars (BCs) derived from jujube (Ziziphus jujube L.) biomass (300 °C and 700 °C) for nylon (NYL) and polyethylene (PE) removal from contaminated water was explored in fixed-bed column trials. The optimum pH for the removal of both MPs was found 7. Both of the produced biochars demonstrated >99% removal of the MPs, while the sand filter exhibited a maximum of 78% removal of MPs. BC produced at 700 °C (BC700) showed 33-fold higher MPs retention, while BC produced at 300 °C (BC300) exhibited 20-fold higher retention, as compared to sand filters, indicating the higher efficiency of BC produced at higher pyrolysis temperature. Entrapment into the pores, entanglement with flaky structures of the BCs, and electrostatics interactions were the major mechanism for MPs retention in BCs. The efficiency of MPs-amended BCs was further explored for the removal of Pb(II) and Cd(II) in fixed-bed column trials. BC700 amended with PE and NYL exhibited the highest 50% breakthrough time (2114.23 and 2024.61 min, respectively, for Pb(II) removal and 2107.92 and 1965.19 min, respectively, for Cd(II) removal), as compared to sand filters (38.07 and 60.49 min for Pb(II) and Cd(II) removal, respectively). Thomas model predicted highest adsorption capacity was exhibited by BC700 amended with PE (584.34 and 552.80 mg g-1, for Pb(II) and Cd(II) removal, respectively), followed by BC700 amended with NYL (557.65 and 210.59 mg g-1 for Pb(II) and Cd(II) removal, respectively). Therefore, jujube waste-derived BCs could be used as efficient adsorbents to remove PE and NYL from contaminated water, while MPs-loaded BCs can further be utilized for higher adsorption of Pb(II) and Cd(II) from contaminated aqueous media. These findings suggest that BC could be used as an efficient adsorbent to remove the co-existing MPs-metals ions from the environment on a sustainable basis.

Microplastic-Assisted Removal of Phosphorus and Ammonium Using Date Palm Waste Derived Biochar.

Microplastics (MPs) are emerging environmental pollutants worldwide, posing potential health risks. Moreover, MPs may act as vectors for other contaminants and affect their fate, transport, and deposition in the environment. Therefore, efficient and economical techniques are needed for the removal of contemporary MPs and contaminants from the environment. The present research study investigated the sorption of phosphorus (P) and ammonium (NH4+) onto date palm waste-derived biochar (BC) from an aqueous solution in the presence of polyamide (PA) and polyethylene (PE) MPs. The BC was prepared at 600 °C, characterized for physio-chemical properties, and applied for P and NH4+ removal via isotherm and kinetic sorption trials. The results of the sorption trials demonstrated the highest removal of NH4+ and P was obtained at neutral pH 7. The highest P sorption (93.23 mg g-1) by BC was recorded in the presence of PA, while the highest NH4+ sorption (103.76 mg g-1) was found with co-occurring PE in an aqueous solution. Sorption isotherm and kinetics models revealed that P and NH4+ removal by MP-amended BC followed chemisorption, electrostatic interaction, precipitation, diffusion, and ion exchange mechanisms. Overall, co-existing PA enhanced the removal of P and NH4+ by 66% and 7.7%, respectively, while co-existing PE increased the removal of P and NH4+ by 55% and 30%, respectively, through the tested BC. Our findings suggested that converting date palm waste into BC could be used as a competent and economical approach to removing P and NH4+ from contaminated water. Furthermore, microplastics such as PE and PA could assist in the removal of P and NH4+ from contaminated water using BC.