Polyaniline Modified CNTs and Graphene Nanocomposite for Removal of Lead and Zinc Metal Ions: Kinetics, Thermodynamics and Desorption Studies.

A novel polyaniline-modified CNT and graphene-based nanocomposite (2.32-7.34 nm) was prepared and characterized by spectroscopic methods. The specific surface area was 176 m2/g with 0.232 cm3/g as the specific pore volume. The nanocomposite was used to remove zinc and lead metal ions from water; showing a high removal capacity of 346 and 581 mg/g at pH 6.5. The data followed pseudo-second-order, intraparticle diffusion and Elovich models. Besides this, the experimental values obeyed Langmuir and Temkin isotherms. The results confirmed that the removal of lead and zinc ions occurred in a mixed mode, that is, diffusion absorption and ion exchange between the heterogeneous surface of the sorbent containing active adsorption centers and the solution containing metal ions. The enthalpy values were 149.9 and 158.6 J.mol-1K-1 for zinc and lead metal ions. The negative values of free energies were in the range of -4.97 to -26.3 kJ/mol. These values indicated an endothermic spontaneous removal of metal ions from water. The reported method is useful to remove the zinc and lead metal ions in any water body due to the high removal capacity of nanocomposite at natural pH of 6.5. Moreover, a low dose of 0.005 g per 30 mL made this method economical. Furthermore, a low contact time of 15 min made this method applicable to the removal of the reported metal ions from water in a short time. Briefly, the reported method is highly economical, nature-friendly and fast and can be used to remove the reported metal ions from any water resource.

Ultralow temperature cryoablation using near-critical nitrogen for cavotricuspid isthmus-ablation, first-in-human results.

INTRODUCTION: Cryoablation has evolved as a safe alternative to radiofrequency ablation in the treatment of several supraventricular arrhythmias and has potential advantages, yet is limited by the properties of the cryogen used. We investigated a novel ultralow temperature cryoablation (ULTC) system using nitrogen near its liquid-vapor critical point as a freezing source, achieving temperatures as low as -196 degrees Celsius in a long linear catheter with a continuous energy release. Initial safety, procedural and efficacy outcomes of ULTC are described in patients undergoing cavotricuspid isthmus (CTI) ablation. METHODS AND RESULTS: The Cryocure studies (NCT02355106, NCT02839304) are prospective, single-arm, multi-center, first-in-human clinical studies in 17 patients with atrial flutter (AFL) and 13 patients with atrial fibrillation (AF). A total of 30 patients, mean age 65 ± 8 years old and 67% male, were enrolled and underwent ablation of the CTI. Acute success, defined as the confirmation of stable bidirectional conduction block across the CTI, was achieved in all 30 patients. After 12 months of follow-up, 14 out of 17 AFL patients remained free from any AFL. One (3.3%) procedure-related but not device-related serious adverse event was reported, involving transient inferolateral ST-elevation associated with temporary AV conduction block. CONCLUSION: In this first-in-human clinical study the safety and performance results demonstrate the capabilities of ultralow temperature near-critical nitrogen as an effective energy source for CTI ablation. Ongoing, larger, studies should confirm our findings and evaluate the capabilities to create linear and focal transmural lesions in other arrhythmias.

Ultralow temperature cryoablation: Safety and efficacy of preclinical atrial and ventricular lesions.

BACKGROUND: Ultralow temperature cyroablation (ULTC) is designed to create focal, linear, and circumferential lesions. The aim of this study was to assess the safety, efficacy, and durability of atrial and ventricular ULTC lesions in preclinical large animal models. METHODS AND RESULTS: The ULTC system uses nitrogen near its liquid-vapor critical point to cool 11-cm ablation catheters. The catheter can be shaped to specific anatomies using pre-shaped stylets. ULTC was used in 11 swine and four sheep to create atrial (pulmonary vein isolation and linear ablation) and ventricular lesions. Acute and 90-day success were evaluated by intracardiac mapping and histologic examination. Cryoadherence was observed during all ULTC applications, ensuring catheter stability at target locations. Local electrograms were completely eliminated immediately after the first single-shot ULTC application in 49 of 53 (92.5%) atrial and in 31 of 32 (96.9%) ventricular applications. Lesion depth as measured on histology preparations was 1.96 ± 0.8 mm in atrial and 5.61 ± 2.2 mm in ventricular lesions. In all animals, voltage maps and histology demonstrated transmural and durable lesions without gaps, surrounded by intact collagen fibers without injury to surrounding tissues. Transient coronary spasm could be provoked with endocardial ULTC in the left ventricle in close proximity to a coronary artery. CONCLUSIONS: ULTC created effective and efficient atrial and ventricular lesions in vivo without procedural complications in two large animal models. ULTC lesions were transmural, contiguous, and durable over 3 months.

Engendering High Energy Density LiFePO4 Electrodes with Morphological and Compositional Tuning.

Improving the energy density of Li-ion batteries is critical to meet the requirements of electric vehicles and energy storage systems. In this work, LiFePO4 active material was combined with single-walled carbon nanotubes as the conductive additive to develop high-energy-density cathodes for rechargeable Li-ion batteries. The effect of the morphology of the active material particles on the cathodes' electrochemical characteristics was investigated. Although providing higher packing density of electrodes, spherical LiFePO4 microparticles had poorer contact with an aluminum current collector and showed lower rate capability than plate-shaped LiFePO4 nanoparticles. A carbon-coated current collector helped enhance the interfacial contact with spherical LiFePO4 particles and was instrumental in combining high electrode packing density (1.8 g cm-3) with excellent rate capability (100 mAh g-1 at 10C). The weight percentages of carbon nanotubes and polyvinylidene fluoride binder in the electrodes were optimized for electrical conductivity, rate capability, adhesion strength, and cyclic stability. The electrodes that were formulated with 0.25 wt.% of carbon nanotubes and 1.75 wt.% of the binder demonstrated the best overall performance. The optimized electrode composition was used to formulate thick free-standing electrodes with high energy and power densities, achieving the areal capacity of 5.9 mAh cm-2 at 1C rate.

Fast-Processable Non-Flammable Phthalonitrile-Modified Novolac/Carbon and Glass Fiber Composites.

Phthalonitrile resins (PN) are known for their incredible heat resistance and at the same time poor processability. Common curing cycle of the PN includes dozens hours of heating at temperatures up to 375 °C. This work was aimed at reducing processing time of phthalonitrile resin, and with this purpose, a novolac oligomer with hydroxyl groups fully substituted by phthalonitrile moieties was synthesized with a quantitative yield. Formation of the reaction byproducts was investigated depending on the synthesis conditions. The product was characterized by 1H NMR and FT-IR. Curing of the resins with the addition of different amounts of novolac phenolic as curing agent (25, 50 and 75 wt.%) was studied by rheological and DSC experiments. Based on these data, a curing program was developed for the further thermosets' investigation: hot-pressing at 220 °C and 1.7 MPa for 20 min. TGA showed the highest thermal stability of the resin with 25 wt.% of novolac (T5% = 430 °C). The post-curing program was developed by the use of DMA with different heating rates and holding for various times at 280 or 300 °C (heating rate 0.5 °C/min). Carbon and glass fiber plastic laminates were fabricated via hot-pressing of prepregs with Tg's above 300 °C. Microcracks were formed in the CFRP, but void-free GFRP were fabricated and demonstrated superior mechanical properties (ILSS up to 86 MPa; compressive strength up to 620 MPa; flexural strength up to 946 MPa). Finally, flammability tests showed that the composite was extinguished in less than 5 s after the flame source was removed, so the material can be classified as V-0 according to the UL94 ratings. For the first time, fast-curing phthalonitrile prepregs were presented. The hot-pressing cycle of 20 min with 150 min free-standing post-curing yielded composites with the unique properties. The combination of mechanical properties, scale-up suitable fast-processing and inflammability makes the presented materials prospective for applications in the electric vehicle industries, fast train construction and the aerospace industry.

Ionomers Based on Addition and Ring Opening Metathesis Polymerized 5-phenyl-2-norbornene as a Membrane Material for Ionic Actuators.

Two types of poly(5-phenyl-2-norbornene) were synthesized via ring opening metathesis and addition polymerization. The polymers sulfonation reaction under homogeneous conditions resulted in ionomer with high sulfonation degree up to 79% (IEC 3.36 meq/g). The prepared ionomer was characterized by DSC, GPC, 1H NMR and FT-IR. Polymers for electromechanical applications soluble in common polar organic solvents were obtained by replacing proton of sulfonic group with imidazolium and 1-methylimidazlium. Membranes were prepared using the above-mentioned polymers and 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF4), as well as mixtures with polyvinylidene fluoride (PVDF). Mechanical, morphological, and conductive properties of the membranes were examined by tensile testing, SEM, and impedance spectroscopy, respectively. Dry and air-stable actuators with electrodes based on SWCNT were fabricated via hot-pressing. Actuators with membranes based on methylimidazolium containing ionomers outperformed classical bucky gel actuator and demonstrated high strain (up to 1.14%) and generated stress (up to 1.21 MPa) under low voltage of 2 V.

The Physicochemical Characterization of New "Green" Epoxy-Resin Hardener Made from PET Waste.

"Green" thermally stable hardener was synthesized from a PET waste. The rigid molecular linear structure of the new hardener suggests that it will provide the polymer matrix with the necessary physical and mechanical characteristics. It also allows the expectation that cured matrix based on this hardener can provide increased toughness. New hardener was used as a curing agent for three epoxy resins-tetraglycidyl methylenedianiline (TGDMA, 111-117 EEW), diglycidylether of bisphenol A (DGEBA, 170-192 EEW) and solid epoxy resin (SER)-with a medium molecular weight (860-930 EEW) based on DGEBA. The mixtures were found to have the highest Tg for the DGEBA resin, and high of that for TGDMA and SER. According to the DMA analysis for two cured matrices, the hardener proved to be no worse than the standard ones, and made it possible to obtain cured matrices with excellent mechanical properties, which allows us to hope for further application of new hardener cured epoxy matrices in appropriate composite materials at high temperatures.

Dynamic and Static Mechanical Properties of Crosslinked Polymer Matrices: Multiscale Simulations and Experiments.

We studied the static and dynamic mechanical properties of crosslinked polymer matrices using multiscale simulations and experiments. We continued to develop the multiscale methodology for generating atomistic polymer networks, and applied it to the case of phthalonitrile resin. The mechanical properties of the resulting networks were analyzed using atomistic molecular dynamics (MD) and dissipative particle dynamics (DPD). The Young's and storage moduli increased with conversion, due both to the appearance of a network of covalent bonds, and to freezing of degrees of freedom and lowering of the glass transition temperature during crosslinking. The simulations' data showed good quantitative agreement with experimental dynamic mechanical analysis measurements at temperatures below the glass transition. The data obtained in MD and DPD simulations at elevated temperatures were conformable. This makes it possible to use the suggested approach for the prediction of mechanical properties of a broad range of polymer matrices, including ones with high structural heterogeneity.