The Facile Synthesis and Application of Mesoporous Silica Nanoparticles with a Vinyl Functional Group for Plastic Recycling.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. The early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

Facile Mesoporous Hollow Silica Synthesis for Formaldehyde Adsorption.

Formaldehyde emitted from household products is classified as a hazardous substance that can adversely affect human health. Recently, various studies related to adsorption materials for reducing formaldehyde have been widely reported. In this study, mesoporous and mesoporous hollow silicas with amine functional groups introduced were utilized as adsorption materials for formaldehyde. Formaldehyde adsorption characteristics of mesoporous and mesoporous hollow silicas having well-developed pores were compared based on their synthesis methods-with or without a calcination process. Mesoporous hollow silica synthesized through a non-calcination process had the best formaldehyde adsorption characteristics, followed by mesoporous hollow silica synthesized through a calcination process and mesoporous silica. This is because a hollow structure has better adsorption properties than mesoporous silica due to large internal pores. The specific surface area of mesoporous hollow silica synthesized without a calcination process was also higher than that synthesized with a calcination process, leading to a better adsorption performance. This research suggests a facile synthetic method of mesoporous hollow silica and confirms its noticeable potential as a support for the adsorption of harmful gases.

Characteristics of CO2 Capture by Tetraethylenepentamine Modified Mesoporous Silica Morphology.

The objective of the study is to investigate the morphology effects of porous silica supports on the CO2 capture performance of solid amine adsorbents. Mesoporous hollow silica spheres (MHSS) and mesoporous silica spheres (MSS) were synthesized and modified by wet impregnation with tetraethylenepentamine (TEPA) as solid adsorbents. The prepared adsorbents were characterized by TEM, XRD, N2 adsorption/desorption, FT-IR, and TGA. The CO2 capture performances of the adsorbents were evaluated using a flow method at atmospheric pressure. Gas chromatography was used to analyze the CO2 concentration in the influent and effluent gas streams. Due to the excellent structural properties of the MHSS, it was found to be a better amine support than MSS. An increase in the amount of loaded TEPA improved the CO2 adsorption capacity of the prepared adsorbents. The optimum CO2 adsorption capacities were obtained with MHSS-47 and MSS-41.

Preparation and Characterization of CuO-TiO2 Composite Hollow Nanospheres with Enhanced Photocatalytic Activity Under Visible Light Irradiation.

CuO-TiO2 composite hollow nanospheres were synthesized using polystyrene as a template. Transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) were used to characterize the average diameter, shell thickness, crystalline structure, and composition of CuO-TiO2 composite hollow nanospheres. UV-vis absorption spectrum was used to measure the optical absorption property of the CuO-TiO2 composite hollow nanospheres. The photocatalytic performance of the samples was characterized by degrading 10 mg·L-1 methylene blue under visible light irradiation. The results showed that the CuO-TiO2 composite hollow nanospheres exhibited better photocatalytic performance than the pure TiO2 nanoparticles and TiO2 hollow nanospheres. The improvement in photocatalytic performance was attributed to the enhanced light absorption in the visible light region.

Effects of Hat-Shaped Mortised Genioplasty with Genioglossus Muscle Advancement on Retrogenia and Snoring: Assessment of Esthetic, Functional, and Psychosocial Results.

BACKGROUND: An increasing number of patients undergo genioplasty for esthetic purposes to correct micrognathism or retrognathism. However, these conditions are considered an important risk factor for snoring. The purpose of this study was to evaluate both esthetic improvement and functional changes of snoring symptoms in patients who underwent hat-shaped mortised advancing genioplasty with genioglossus muscle advancement. MATERIALS AND METHODS: This retrospective study enrolled 25 patients. We evaluated scores for subjective snoring classification (Stanford scale) and questionnaire findings for esthetic results. RESULTS: Most people (96%) were satisfied with the esthetic improvement after surgery. The grade of subjective snoring classification (Stanford scale) improved from 8.68 (range 0-10) to 4.08 (range 0-10) after surgery. Twenty-four patients had an improved snoring grade. All patients reported a positive impact on their daily activity and self-confidence, and they were willing to recommend the same operation to someone with the same clinical problems. CONCLUSION: We conclude that hat-shaped mortised advancing genioplasty with genioglossus muscle advancement can relieve the symptoms of snoring for patients with hypoplastic chin or retrogenia. Patients were satisfied with the functional and esthetic results. LEVEL OF EVIDENCE IV: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Analysis of CO2 Adsorption Characteristics of Activated Carbon Loaded with Alkali and Alkaline Earth Metal.

Adsorbents that can effectively trap CO2 gas are actively being studied due to worldwide increases in CO2 emissions. Although activated carbon is a leading adsorbent because of advantages such as low costs and a wide specific surface area, it is limited in the sense that it does not adsorb CO2 alone. Therefore, in this study, the adsorption characteristics of CO2 were analyzed by loading KOH and/or Ba(OH)2 on activated carbon at room temperature. Loaded KOH and/or Ba(OH)2 were identified by SEM-EDX and BET analysis, respectively, and the CO2 adsorption performances were confirmed using a gas flow system with GC. We confirmed that the CO2 adsorption performance was significantly improved when activated carbon was pretreated with KOH and Ba(OH)2, respectively. It can be seen from the XPS analysis that, when both KOH and Ba(OH)2 were loaded on the same activated carbon, it had a synergy effect on CO2 adsorption performance.

Combined Embedding of N/F-Doping and CaCO3 Surface Modification in the TiO2 Photoanode for Dye-Sensitized Solar Cells.

N/F-doping and CaCO3 surface modification was carried out in TiO2 photoelectrodes for dye-sensitized solar cells (DSSCs). The combined effect of the N/F doped TiO2 and the CaCO3 coating showed a great increase of the short-circuit current (J(sc)), and photoelectric conversion efficiency (η) of the prepared cells; the efficiency (η) was improved from 7.00% of a commercial TiO2 photoelectrode to 7.90% of an uncoated N/F-doped electrode, and to 9.09% of a N/F-doped and CaCO3 surface modified electrode. An enhanced photoresponse in N/F-doped TiO2 nanoparticles generate more photo-excited electrons, as supported by measured UV-Vis diffuse reflectance spectra. A successive CaCO3 surface modification then forms a barrier on the surface of the N/F-doped TiO2 particles; the higher basicity of the CaCO3 modified TiO2 facilitates the dye adsorption, as supported by the direct measurement of the amount of adsorbed dye.

Control of adhesion force between ceria particles and polishing pad in shallow trench isolation chemical mechanical planarization.

The adhesion force between ceria and polyurethane (PU) pad was controlled to remove the step height from cell region to peripheral region during Shallow Trench Isolation Chemical Mechanical Planarization (STI-CMP) for NAND flash. Picolinic acid was found to be adsorbed on ceria particles at pH 4.5 following a Langmuir isotherm with the maximum adsorbed amount of 0.36 mg/m2. The ceria suspension with full surface coverage of picolinic acid showed a threefold increase in the number of adhered ceria particles on the PU pad over non-coated ceria particles. It was shown that the coverage percent of picolinic acid on ceria corresponds well with the amount percent of adsorbed ceria on PU pad. The change in adsorbed particles was directly reflected in the CMP polishing process where significant improvements were achieved. Particularly, convex areas on the chip experienced higher friction force from the attached abrasives on the PU pad than concave areas. As a result, the convex areas have increased removal rate of step height compared to the ceria suspension without picolinic acid. The changing profiles of convex areas are reported during the step height reduction as a function of polishing time.

Synthesis of Mesoporous Silica Sol with Low Refractive Properties for Increasing Transmittance.

Currently, coating with anti-reflective materials is an attractive approach to improve the quality of screen-based displays. In this study, mesoporous silica particles were systematically synthesized as a function of surfactant (i.e., CTAC-cetyltrimethylammonium chloride) concentration to serve as main coating fillers possessing low refractive indices. Precisely changing the amount of the CTAC surfactant, silica sol with an average diameter of 50 nm exhibits distinctively different specific surface areas, pore size, and pore volume. Prior to the preparation of final coating solutions containing these silica particle fillers, the percentage of solid content was optimized on a glass slide. The use of 50 wt% solid content exhibited the highest transmittance of light. Among various content levels of silica sol, the use of 3.5 wt% of silica particles in the solid content displayed the highest transmittance (i.e., best anti-reflectiveness). Under the almost identical coating layers prepared with the fixed amount of silica particles possessing different surface areas, pore size, and pore volume, it appears that the largest pore volume played the most important role in improving the anti-reflective properties. Experimentally understanding the key feature of low-refractive filler materials under the optimized conditions could provide a clear view to develop highly effective anti-reflective materials for various display applications.

Amine-Impregnated Dendritic Mesoporous Silica for the Adsorption of Formaldehyde.

To adsorb and remove formaldehyde, which is a harmful volatile organic chemical (VOC) detected indoors, an alkylamine was introduced into the substrate as a formaldehyde adsorbent. In this study, Tetraethylenepentaamine (TEPA) was introduced into the mesoporous silica using the amine impregnation method. Since the impregnated alkylamine can block the pores of the silica substrate, the pore size and pore volume are very important factors for its use as a substrate for an adsorbent. Focusing on the substrate's pore properties, Santa Barbara Amorphous-15 (SBA-15) was chosen as a conventional one-dimensional pore-structured mesoporous silica, and dendritic mesoporous silica (DMS) as a three-dimensional pore-structured mesoporous silica. To 1 g each of silica substrate DMS and SBA-15, 0, 0.5, 1.5, and 2.5 g of TEPA were introduced. A fixed concentration and amount of formaldehyde gas was flowed through the adsorbent and then the adsorbent was changed to the 2,4-Dinitrophenylhydrazine (2,4-DNPH) cartridge to adsorb the remaining formaldehyde. According to the methods recommended by the World Health Organization (WHO) and National Institute for Occupational Safety & Health (NIOSH), the formaldehyde captured by 2,4-DNPH was analyzed using high-performance liquid chromatography (HPLC). A comparison of DMS and SBA-15 in the amine impregnation method shows that not only surface area, but also large pore size and high pore volume, contribute to the formaldehyde adsorption ability.

Highly Elastic and Conductive Metallic Interconnect with Crystalline-Amorphous Nanolaminate.

Nanolaminate with alternating layers of nanocrystalline Cu and amorphous CuZrTi is suggested as highly stretchable and conductive interconnect material in stretchable devices. 50 nm nanocrystalline Cu and 20 nm amorphous CuZrTi are the optimum thicknesses of the constituent layers, which result in an elastic deformation limit of 3.33% similar to that of the monolithic amorphous CuZrTi film and an electrical conductivity of 11.83 S/µm corresponding to 70% of that of the monolithic nanocrystalline Cu film. The enhanced elastic deformability and conductivity of the nanolaminates enable the maintenance of the interconnect performance for cyclic stretching with a tensile strain of 114% in the form of a free-standing serpentine structure and a tensile strain of 30% in the form of an ordinary circular coil on an elastomer substrate.

Electroceuticals for Regeneration of Long Nerve Gap Using Biodegradable Conductive Conduits and Implantable Wireless Stimulator.

Regeneration of over 10 mm long peripheral nerve defects remains a challenge due to the failure of regeneration by prolonged axotomy and denervation occurring in long-term recovery. Recent studies reveal that conductive conduits and electrical stimulation accelerate the regeneration of long nerve defects. In this study, an electroceutical platform combining a fully biodegradable conductive nerve conduit and a wireless electrical stimulator is proposed to maximize the therapeutic effect on nerve regeneration. Fully biodegradable nerve conduit fabricated using molybdenum (Mo) microparticles and polycaprolactone (PCL) can eliminate the unwanted effects of non-degradable implants, which occupy nerve paths and need to be removed through surgery increasing the risk of complications. The electrical and mechanical properties of Mo/PCL conduits are optimized by controlling the amounts of Mo and tetraglycol lubricant. The dissolution behavior and electrical conductivity of biodegradable nerve conduits in the biomimetic solutions are also evaluated. In in vivo experiments, the integrated strategy of a conductive Mo/PCL conduit with controlled therapeutic electrical stimulation shows accelerated axon regeneration for long sciatic nerve defects in rats compared to the use of the Mo/PCL conduit without stimulation and has a significant therapeutic effect based on the results obtained from the functional recovery test.

Lifetime-configurable soft robots via photodegradable silicone elastomer composites.

Developing soft robots that can control their own life cycle and degrade on-demand while maintaining hyperelasticity is a notable research challenge. On-demand degradable soft robots, which conserve their original functionality during operation and rapidly degrade under specific external stimulation, present the opportunity to self-direct the disappearance of temporary robots. This study proposes soft robots and materials that exhibit excellent mechanical stretchability and can degrade under ultraviolet light by mixing a fluoride-generating diphenyliodonium hexafluorophosphate with a silicone resin. Spectroscopic analysis revealed the mechanism of Si─O─Si backbone cleavage using fluoride ion (F-) and thermal analysis indicated accelerated decomposition at elevated temperatures. In addition, we demonstrated a robotics application by fabricating electronics integrated gaiting robot and a fully closed-loop trigger disintegration robot for autonomous, application-oriented functionalities. This study provides a simple yet novel strategy for designing life cycle mimicking soft robotics that can be applied to reduce soft robotics waste, explore hazardous areas, and ensure hardware security with on-demand destructive material platforms.

Enhanced electron lifetime on nitrogen-doped TiO2 films for dye-sensitized solar cells.

Nitrogen-doped TiO2 crystallites were prepared via the hydrolysis of TiCl4 using an ammonia medium in an aqueous solution for DSSC photoelectrodes. The optimized photoelectrode for the DSSC was prepared with 9.4 nm sized N-doped TiO2 crystal (BET; 200 m2/g), which provides a relatively high short circuit current and energy conversion efficiency in the DSSC. The photovoltaic performance of the N-doped TiO2 electrode was confirmed using incident photon-to-current efficient spectra, impedance analyses, and Bode-phase plots which proved that the N-doped TiO2 electrode has a significantly enhanced electron lifetime compared with that of the P25 electrode.

Micro-to-Nanometer Scale Patterning of Perovskite Inks via Controlled Self-Assemblies.

In the past decade, perovskite materials have gained intensive interest due to their remarkable material properties in optoelectronics and photodetectors. This review highlights recent advances in micro-to-nanometer scale patterning of perovskite inks, placing an undue emphasis on recently developed approaches to harness spatially ordered and crystallographically oriented structures with unprecedented regularity via controlled self-assemblies, including blade coating, inkjet printing, and nanoimprinting. Patterning of the perovskite elements at the micro- or nanometer scale might be a key parameter for their integration in a real system. Nowadays, unconventional approaches based on irreversible solution evaporation hold an important position in the structuring and integration of perovskite materials. Herein, easier type patterning techniques based on evaporations of polymer solutions and the coffee ring effect are systematically reviewed. The recent progress in the potential applications of the patterned perovskite inks is also introduced.

Facile Synthesis of Mesoporous Silica at Room Temperature for CO2 Adsorption.

Although mesoporous silica materials have been widely investigated for many applications, most silica materials are made by calcination processes. We successfully developed a convenient method to synthesize mesoporous materials at room temperature. Although the silica materials made by the two different methods, which are the calcination process and the room-temperature process, have similar specific surface areas, the silica materials produced with the room-temperature process have a significantly larger pore volume. This larger pore volume has the potential to attach to functional groups that can be applied to various industrial fields such as CO2 adsorption. This mesoporous silica with a larger pore volume was analyzed by TEM, FT-IR, low angle X-ray diffraction, N2-adsorption analysis, and CO2 adsorption experiments in comparison with the mesoporous silica synthesized with the traditional calcination method.

Silicon Wafer CMP Slurry Using a Hydrolysis Reaction Accelerator with an Amine Functional Group Remarkably Enhances Polishing Rate.

Recently, as an alternative solution for overcoming the scaling-down limitations of logic devices with design length of less than 3 nm and enhancing DRAM operation performance, 3D heterogeneous packaging technology has been intensively researched, essentially requiring Si wafer polishing at a very high Si polishing rate (500 nm/min) by accelerating the degree of the hydrolysis reaction (i.e., Si-O-H) on the polished Si wafer surface during CMP. Unlike conventional hydrolysis reaction accelerators (i.e., sodium hydroxide and potassium hydroxide), a novel hydrolysis reaction accelerator with amine functional groups (i.e., 552.8 nm/min for ethylenediamine) surprisingly presented an Si wafer polishing rate >3 times higher than that of conventional hydrolysis reaction accelerators (177.1 nm/min for sodium hydroxide). This remarkable enhancement of the Si wafer polishing rate for ethylenediamine was principally the result of (i) the increased hydrolysis reaction, (ii) the enhanced degree of adsorption of the CMP slurry on the polished Si wafer surface during CMP, and (iii) the decreased electrostatic repulsive force between colloidal silica abrasives and the Si wafer surface. A higher ethylenediamine concentration in the Si wafer CMP slurry led to a higher extent of hydrolysis reaction and degree of adsorption for the slurry and a lower electrostatic repulsive force; thus, a higher ethylenediamine concentration resulted in a higher Si wafer polishing rate. With the aim of achieving further improvements to the Si wafer polishing rates using Si wafer CMP slurry including ethylenediamine, the Si wafer polishing rate increased remarkably and root-squarely with the increasing ethylenediamine concentration.

A Personalized Electronic Tattoo for Healthcare Realized by On-the-Spot Assembly of an Intrinsically Conductive and Durable Liquid-Metal Composite.

Conventional electronic (e-) skins are a class of thin-film electronics mainly fabricated in laboratories or factories, which is incapable of rapid and simple customization for personalized healthcare. Here a new class of e-tattoos is introduced that can be directly implemented on the skin by facile one-step coating with various designs at multi-scale depending on the purpose of the user without a substrate. An e-tattoo is realized by attaching Pt-decorated carbon nanotubes on gallium-based liquid-metal particles (CMP) to impose intrinsic electrical conductivity and mechanical durability. Tuning the CMP suspension to have low-zeta potential, excellent wettability, and high-vapor pressure enables conformal and intimate assembly of particles directly on the skin in 10 s. Low-cost, ease of preparation, on-skin compatibility, and multifunctionality of CMP make it highly suitable for e-tattoos. Demonstrations of electrical muscle stimulators, photothermal patches, motion artifact-free electrophysiological sensors, and electrochemical biosensors validate the simplicity, versatility, and reliability of the e-tattoo-based approach in biomedical engineering.

Synthesis and Characteristics of Double-Shell Mesoporous Hollow Silica Nanomaterials to Improve CO2 Adsorption Performance.

To improve the adsorption performance of carbon dioxide, which is considered the main culprit of greenhouse gases, the specific surface area and high pore volume of the adsorbing material should be considered. For a porous material, the performance of carbon dioxide adsorption is determined by the amine groups supporting capacity; the larger the pore volume, the greater the capacity to support the amine groups. In this study, a double-shell mesoporous hollow silica nanomaterial with excellent pore volume and therefore increased amine support capacity was synthesized. A core-shell structure capable of having a hollow shape was synthesized using polystyrene as a core material, and a double-shell mesoporous shape was synthesized by sequentially using two types of surfactants. The synthesized material was subjected to a sintering process of 600 degrees, and the N2 sorption analysis confirmed a specific surface area of 690 m2/g and a pore volume of 1.012 cm3/g. Thereafter, the amine compound was impregnated into the silica nanomaterial, and then, a carbon dioxide adsorption experiment was conducted, which confirmed that compared to the mesoporous hollow silica nanomaterial synthesized as a single shell, the adsorption performance was improved by about 1.36 times.

Risk and protective factors affecting sensory recovery after breast reconstruction.

BACKGROUND: Although loss of sensation in patients with breast cancer after mastectomy followed by breast reconstruction is an important factor affecting patients' quality of life, the mechanism of sensory recovery is still unclear. Our study aimed to identify variables that affect sensory recovery, especially pain, in reconstructed breasts. METHODS: All patients with breast cancer who underwent mastectomy followed by immediate breast reconstruction, including nipple reconstruction or areolar tattooing, were included in this study. Sensation was evaluated in the nipple as an endpoint of sensation recovery of the whole breast. Patients rated pain severity using a 3-point verbal rating scale (VRS): grade 0, no pain; grade 1, mild to moderate pain; and grade 2, severe pain. The VRS was assessed by a single experienced plastic surgeon. RESULTS: In the univariate analysis, the odds ratio (OR) for sensation recovery was 0.951 for age (P=0.014), 0.803 for body mass index (P=0.001), 0.996 for breast volume before surgery (P=0.001), 0.998 for specimen weight after mastectomy (P=0.040), and 1.066 for the period between mastectomy and sensory assessment (P=0.003). In the multivariate analysis, the variables that showed a significant effect were age (OR, 0.953; P=0.034), the period between mastectomy and sensory assessment (OR, 1.071; P=0.006), and reconstruction using abdominal tissue instead of prosthetic reconstruction (OR, 0.270; P=0.004). CONCLUSIONS: Based on our results, it can be inferred that aging has a negative impact on the recovery of sensation, breast sensation improves with time after surgery, and the recovery of sensation is better in prosthetic reconstruction.