RESUMEN
Photonic bound states in the continuum (BICs), embedded in the spectrum of free-space waves1,2 with diverging radiative quality factor, are topologically non-trivial dark modes in open-cavity resonators that have enabled important advances in photonics3,4. However, it is particularly challenging to achieve maximum near-field enhancement, as this requires matching radiative and non-radiative losses. Here we propose the concept of supercritical coupling, drawing inspiration from electromagnetically induced transparency in near-field coupled resonances close to the Friedrich-Wintgen condition2. Supercritical coupling occurs when the near-field coupling between dark and bright modes compensates for the negligible direct far-field coupling with the dark mode. This enables a quasi-BIC field to reach maximum enhancement imposed by non-radiative loss, even when the radiative quality factor is divergent. Our experimental design consists of a photonic-crystal nanoslab covered with upconversion nanoparticles. Near-field coupling is finely tuned at the nanostructure edge, in which a coherent upconversion luminescence enhanced by eight orders of magnitude is observed. The emission shows negligible divergence, narrow width at the microscale and controllable directivity through input focusing and polarization. This approach is relevant to various physical processes, with potential applications for light-source development, energy harvesting and photochemical catalysis.
RESUMEN
Tip-enhanced photoluminescence (TRPL) is a powerful technique for spatially and spectrally probing local optical properties of 2-dimensional (2D) materials that are modulated by the local heterogeneities, revealing inaccessible dark states due to bright state overlap in conventional far-field microscopy at room temperature. While scattering-type near-field probes have shown the potential to selectively enhance and reveal dark exciton emission, their technical complexity and sensitivity can pose challenges under certain experimental conditions. Here, we present a highly reproducible and easy-to-fabricate near-field probe based on nanoimprint lithography and fiber-optic excitation and collection. The novel near-field measurement configuration provides an â¼3 orders of magnitude out-of-plane Purcell enhancement, diffraction-limited excitation spot, and subdiffraction hyperspectral imaging resolution (below 50 nm) of dark exciton emission. The effectiveness of this high spatial XD mapping technique was then demonstrated through reproducible hyperspectral mapping of oxidized sites and bubble areas.
RESUMEN
Scanning near-field optical microscopy (SNOM) is an important technique used to study the optical properties of material systems at the nanoscale. In previous work, we reported on the use of nanoimprinting to improve the reproducibility and throughput of near-field probes including complicated optical antenna structures such as the 'campanile' probe. However, precise control over the plasmonic gap size, which determines the near-field enhancement and spatial resolution, remains a challenge. Here, we present a novel approach to fabricating a sub-20â nm plasmonic gap in a near-field plasmonic probe through the controlled collapse of imprinted nanostructures using atomic layer deposition (ALD) coatings to define the gap width. The resulting ultranarrow gap at the apex of the probe provides a strong polarization-sensitive near-field optical response, which results in an enhancement of the optical transmission in a broad wavelength range from 620 to 820â nm, enabling tip-enhanced photoluminescence (TEPL) mapping of 2-dimensional (2D) materials. We demonstrate the potential of this near-field probe by mapping a 2D exciton coupled to a linearly polarized plasmonic resonance with below 30â nm spatial resolution. This work proposes a novel approach for integrating a plasmonic antenna at the apex of the near-field probe, paving the way for the fundamental study of light-matter interactions at the nanoscale.
RESUMEN
We demonstrate fabrication of nano-patterned thin ALD (Atomic layer deposition) membrane (suspended/transferable) by using a bi-layer resist process where the bottom layer resist acts as a sacrificial layer. This method enables an all dry deterministic transfer of nano-patterned ALD membrane on desired substrate, allowing assembly of multitude of hetero-structures and functionalities that are not yet accessible. Unlike conventional ways of achieving patterned alumina membrane reported in literature our technique requires significantly less fabrication steps and paves the way for novel ALD membrane-based technology.
RESUMEN
Aluminum bowtie nanoantennas represent a possibility to confine and enhance electromagnetic (EM) field at optical frequencies in subwavelength regions by using an abundant and inexpensive metal. The native oxidation process of this metal is often viewed as a limitation for its application in plasmonics. Here, we show that in close gap configurations, the high refractive index of the native aluminum oxide helps in squeezing the plasmonic mode in extremely reduced size volumes, providing a higher EM near-field confinement and enhancement in the bowtie antenna gaps than achieved in the pure aluminum counterpart. Hence, the study provides new perspectives in the use of such a plasmonic antenna geometry within this aluminum system, which can be useful for improving plasmonics-enabled effects such as surface-enhanced Raman scattering- and light-matter interaction in strong coupling regime.
RESUMEN
In this work, we investigate the evanescent field sensing mechanism provided by an all-dielectric metasurface supporting bound states in the continuum (BICs). The metasurface is based on a transparent photonic crystal with subwavelength thickness. The BIC electromagnetic field is localized along the direction normal to the photonic crystal nanoscale-thin slab (PhCS) because of a topology-induced confinement, exponentially decaying in the material to detect. On the other hand, it is totally delocalized in the PhCS plane, which favors versatile and multiplexing sensing schemes. Liquids with different refractive indices, ranging from 1.33 to 1.45, are infiltrated in a microfluidic chamber bonded to the sensing dielectric metasurface. We observe an experimental exponential sensitivity leading to differential values as large as 226 nm/RIU with excellent FOM. This behavior is explained in terms of the physical superposition of the field with the material under investigation and supported by a thorough numerical analysis. The mechanism is then translated to the case of molecular adsorption where a suitable theoretical engineering of the optical structure points out potential sensitivities as large as 4000 nm/RIU.
RESUMEN
The next generation of hard disk drive technology for data storage densities beyond 5 Tb/in2 will require single-bit patterning of features with sub-10 nm dimensions by nanoimprint lithography. To address this challenge master templates are fabricated using pattern multiplication with atomic layer deposition (ALD). Sub-10 nm lithography requires a solid understanding of materials and their interactions. In this work we study two important oxide materials, silicon dioxide and titanium dioxide, as the pattern spacer and look at their interactions with carbon, chromium and silicon dioxide. We found that thermal titanium dioxide ALD allows for the conformal deposition of a spacer layer without damaging the carbon mandrel and eliminates the surface modification due to the reactivity of the metal-organic precursor. Finally, using self-assembled block copolymer lithography and thermal titanium dioxide spacer fabrication, we demonstrate pattern doubling with 7.5 nm half-pitch spacer features.
RESUMEN
We report controllable anisotropic light emission of photons originating from vertically aligned transition dipole moments in spun-cast films of CsPbBr3 nanocubes. By depositing films of nanocrystals on precoated substrates we can control the packing density and resultant radiation pattern of the emitted photons. We develop a technical framework to calculate the average orientation of light emitters, i.e., the angle between the transition dipole moment vector (TDM) and the substrate. This model is applicable to any emissive material with a known refractive index. Theoretical modeling indicates that oriented emission originates from an anisotropic alignment of the valence band and conduction band edge states on the ionic crystal lattice and demonstrates a general path to model the experimentally less accessible internal electric field of a nanosystem from the photoluminescent anisotropy. The uniquely accessible surface of the perovskite nanoparticles allows for perturbation of the normally isotropic emissive transition. The reported sensitive and tunable TDM orientation and control of emitted light will allow for applications of perovskite nanocrystals in a wide range of photonic technologies inaccessible to traditional light emitters.
RESUMEN
In this Letter, we present a design and simulations of the novel hybrid photonic-plasmonic near-field probe. Near-field optics is a unique imaging tool that provides optical images with resolution down to tens of nanometers. One of the main limitations of this technology is its low light sensitivity. The presented hybrid probe solves this problem by combining a campanile plasmonic probe with the photonic layer, consisting of the diffractive optic element (DOE). The DOE is designed to match the plasmonic field at the broad side of the campanile probe with the fiber mode. This makes it possible to optimize the size of the campanile tip to convert light efficiently into the hot spot. The simulations show that the hybrid probe is â¼540 times more efficient compared with the conventional campanile on average in the 600-900 nm spectral range.
RESUMEN
In this Letter, we present a Fresnel lens fabricated on the end of an optical fiber. The lens is fabricated using nanoimprint lithography of a functional high refractive index material, which is suitable for mass production. The main advantage of the presented Fresnel lens compared to a conventional fiber lens is its high refractive index (n=1.68), which enables efficient light focusing even inside other media, such as water or an adhesive. Measurement of the lens performance in an immersion liquid (n=1.51) shows a near diffraction limited focal spot of 810 nm in diameter at the 1/e2 intensity level for a wavelength of 660 nm. Applications of such fiber lenses include integrated optics, optical trapping, and fiber probes.
RESUMEN
Nanoimprint lithography (NIL) of functional high-refractive index materials has proved to be a powerful candidate for the inexpensive manufacturing of high-resolution photonic devices. In this paper, we demonstrate the fabrication of printable photonic crystals (PhCs) with high refractive index working in the visible wavelengths. The PhCs are replicated on a titanium dioxide-based high-refractive index hybrid material by reverse NIL with almost zero shrinkage and high-fidelity reproducibility between mold and printed devices. The optical responses of the imprinted PhCs compare very well with those fabricated by conventional nanofabrication methods. This study opens the road for a low-cost manufacturing of PhCs and other nanophotonic devices for applications in visible light.
RESUMEN
Integration of complex photonic structures onto optical fiber facets enables powerful platforms with unprecedented optical functionalities. Conventional nanofabrication technologies, however, do not permit viable integration of complex photonic devices onto optical fibers owing to their low throughput and high cost. In this paper we report the fabrication of a three-dimensional structure achieved by direct nanoimprint lithography on the facet of an optical fiber. Nanoimprint processes and tools were specifically developed to enable a high lithographic accuracy and coaxial alignment of the optical device with respect to the fiber core. To demonstrate the capability of this new approach, a 3D beam splitter has been designed, imprinted and optically characterized. Scanning electron microscopy and optical measurements confirmed the good lithographic capabilities of the proposed approach as well as the desired optical performance of the imprinted structure. The inexpensive solution presented here should enable advancements in areas such as integrated optics and sensing, achieving enhanced portability and versatility of fiber optic components.
RESUMEN
We report a novel nanofabrication method to fabricate printable integrated circuits with a high refractive index working in the visible wavelength range. The printable planar ligthwave circuits are directly imprinted by ultra-violet nanoimprinting into functional TiO2-based resist on the top of planar waveguide core films. The printed photonic circuits are composed of several elementary components including ridge waveguides, light splitters and digital planar holograms. Multi-mode ridge waveguides with propagation losses around 40 dB cm(-1) at 660 nm wavelength, and, on-chip demultiplexers operated in the visible range with 100 channels and a spectral channel spacing around 0.35 nm are successfully demonstrated.
RESUMEN
Plasmonic metal/semiconductor nanocomposites promise to be a breakthrough for boosting and investigating photon-assisted processes at the nanoscale, with exciting perspectives for energy conversion and catalysis. However, the efficiency and selectivity of these surface processes are still far from being controlled. Here, shown for the first time, is a new class of photocatalyst which is based on the synergistic combination of bowtie-like gold nanoantennas and SiO2 /TiO2 core/shell oxide beads. These systems are exploited as efficient near-field optical light concentrators, stimulating photon-driven processes at the metal-semiconductor interface. Extraordinary enhancements of photodegradation rates (minutes instead of hours) result from matching the nanoantenna surface plasmon resonance with the optical absorption of organic dyes and the excitation source wavelength. Moreover, strong Raman enhancements are observed allowing for direct in-situ monitoring of reaction progress of different analytes on the same site.
RESUMEN
Efficient conversion of photonic to plasmonic energy is important for nano-optical applications, particularly imaging and spectroscopy. Recently a new generation of photonic/plasmonic transducers, the 'campanile' probes, has been developed that overcomes many shortcomings of previous near-field probes by efficiently merging broadband field enhancement with bidirectional coupling of far- to near-field electromagnetic modes. In this work we compare the properties of the campanile structure with those of current NSOM tips using finite element simulations. Field confinement, enhancement, and polarization near the apex of the probe are evaluated relative to local fields created by conical tapered tips in vacuum and in tip-substrate gap mode. We show that the campanile design has similar field enhancement and bandwidth capabilities as those of ultra-sharp metallized tips, but without the substrate and sample restrictions inherent in the tip-surface gap mode operation often required by those tips. In addition, we show for the first time that this campanile probe structure also significantly enhances the radiative rate of any dipole emitter located near the probe apex, quantifying the enhanced decay rate and demonstrating that over 90% of the light radiated by the emitter is "captured" by this probe. This is equivalent to collecting the light from a solid angle of ~3.6 pi. These advantages are crucial for performing techniques such as Raman and IR spectroscopy, white-light nano-ellipsometry and ultrafast pump-probe studies at the nanoscale.
Asunto(s)
Diseño Asistido por Computadora , Resonancia por Plasmón de Superficie/instrumentación , Transductores , Simulación por Computador , Diseño de Equipo , Análisis de Falla de Equipo , Luz , Modelos Teóricos , Dispersión de RadiaciónRESUMEN
A novel and robust route for high-throughput, high-performance nanophotonics-based direct imprint of high refractive index and low visible wavelength absorption materials is presented. Sub-10 nm TiO2 nanostructures are fabricated by low-pressure UV-imprinting of an organic-inorganic resist material. Post-imprint thermal annealing allows optical property tuning over a wide range of values. For instance, a refractive index higher than 2.0 and an extinction coefficient close to zero can be achieved in the visible wavelength range. Furthermore, the imprint resist material permits fabrication of crack-free nanopatterned films over large areas and is compatible for fabricating printable photonic structures.
RESUMEN
Near-field dipolar plasmon interactions of multiple infrared antenna structures in the strong coupling limit are studied using scattering-type scanning near-field optical microscope (s-SNOM) and theoretical finite-difference time-domain (FDTD) calculations. We monitor in real-space the evolution of plasmon dipolar mode of a stationary antenna structure as multiple resonantly matched dipolar plasmon particles are closely approaching it. Interparticle separation, length and polarization dependent studies show that the cross geometry structure favors strong interparticle charge-charge, dipole-dipole and charge-dipole Coulomb interactions in the nanometer scale gap region, which results in strong field enhancement in cross-bowties and further allows these structures to be used as polarization filters. The nanoscale local field amplitude and phase maps show that due to strong interparticle Coulomb coupling, cross-bowtie structures redistribute and highly enhance the out-of-plane (perpendicular to the plane of the sample) plasmon near-field component at the gap region relative to ordinary bowties.
RESUMEN
The ability to correlate optical hyperspectral mapping and high resolution topographic imaging is critically important to gain deep insight into the structure-function relationship of nanomaterial systems. Scanning near-field optical microscopy can achieve this goal, but at the cost of significant effort in probe fabrication and experimental expertise. To overcome these two limitations, we have developed a low-cost and high-throughput nanoimprinting technique to integrate a sharp pyramid structure on the end facet of a single-mode fiber that can be scanned with a simple tuning-fork technique. The nanoimprinted pyramid has two main features: (1) a large taper angle (â¼70°), which determines the far-field confinement at the tip, resulting in a spatial resolution of 275 nm, an effective numerical aperture of 1.06, and (2) a sharp apex with a radius of curvature of â¼20 nm, which enables high resolution topographic imaging. Optical performance is demonstrated through evanescent field distribution mapping of a plasmonic nanogroove sample, followed by hyperspectral photoluminescence mapping of nanocrystals using a fiber-in-fiber-out light coupling mode. Through comparative photoluminescence mapping on 2D monolayers, we also show a threefold improvement in spatial resolution over chemically etched fibers. These results show that the bare nanoimprinted near-field probes provide simple access to spectromicroscopy correlated with high resolution topographic mapping and have the potential to advance reproducible fiber-tip-based scanning near-field microscopy.
RESUMEN
Digital holographic microscopy (DHM) has been successfully applied for the first time to characterize the radiative out-of-plane emission properties of a superdirective device. Complementarily to near-field microscopy, DHM allows us to reconstruct the beam in the far-field region. The angular dispersion of the light beam radiated from a grating composed of air and anti-air metamaterial has been determined, and the proposed technique has highlighted a collimation degree higher than 0.04°, as already evaluated in a previous work. Further considerations on the retrieved phase map of the beam in the acquisition plane are presented.
RESUMEN
Quadrupole plasmon and (octupolar) Fano resonances are induced in lithographically fabricated theta-shaped ring-rod gold nanostructures. The optical response is characterized by measuring the light scattered by individual nanostructures. When the nanorod is brought within 3 nm of the ring wall, a weak quadrupolar resonance is observed due to capacitive coupling, and when a necklike conductive bridge links the nanorod to the nanoring the optical response changes dramatically bringing the quadrupolar resonance into prominence and creating an octupolar Fano resonance. The Fano resonance is observed due to the destructive interference of the octupolar resonance with the overlapping and broadened dipolar resonance. The quadrupolar and Fano resonances are further enhanced by capacitive coupling (near-field interaction) that is favored by the theta-shaped arrangement. The interpretation of the data is supported by FDTD simulation.