An Internal-State-Variable-Based Continuous Dynamic Recrystallization Model for Thermally Deformed TC18 Alloy.

Continuous dynamic recrystallization (CDRX) is widely acknowledged to occur during hot forming and plays a significant role in microstructure development in alloys with moderate to high stacking fault energy. In this work, the flow stress and CDRX behaviors of the TC18 alloy subjected to hot deformation across a wide range of processing conditions are studied. It is observed that deformation leads to the formation of new low-angle grain boundaries (LAGBs). Subgrains rotate by absorbing dislocations, resulting in an increase in LAGB misorientation and the transition of some LAGBs into high-angle grain boundaries (HAGBs). The HAGBs migrate within the material, assimilating the (sub)grain boundaries. Subsequently, an internal state variable (ISV)-based CDRX model is developed, incorporating parameters such as the dislocation density, adiabatic temperature rise, subgrain rotation, LAGB area, HAGB area, and LAGB misorientation angle distribution. The values of the correlation coefficient (R), relative average absolute error (RAAE), and root-mean-square error (RMSE) between the anticipated true stress and measured stress are 0.989, 6.69%, and 4.78 MPa, respectively. The predicted outcomes demonstrate good agreement with experimental findings. The evolving trends of the subgrain boundary area under various conditions are quantitatively analyzed by assessing the changes in dynamic recovery (DRV)-eliminated dislocations and misorientation angles. Moreover, the ISV-based model accurately predicts the decreases in grain and crystallite sizes with higher strain rates and lower temperatures. The projected outcomes also indicate a transition from a stable and coarse-grained microstructure to a continuously recrystallized substructure.

Investigation on Mechanism of Microstructure Evolution during Multi-Process Hot Forming of GH4169 Superalloy Forging.

Typically, in the manufacturing of GH4169 superalloy forgings, the multi-process hot forming that consists of pre-deformation, heat treatment and final deformation is required. This study focuses on the microstructural evolution throughout hot working processes. Considering that δ phase can promote nucleation and limit the growth of grains, a process route was designed, including pre-deformation, aging treatment (AT) to precipitate sufficient δ phases, high temperature holding (HTH) to uniformly heat the forging, and final deformation. The results show that the uneven strain distribution after pre-deformation has a significant impact on the subsequent refinement of the grain microstructure due to the complex coupling relationship between the evolution of the δ phase and recrystallization behavior. After the final deformation, the fine-grain microstructure with short rod-like δ phases as boundaries is easy to form in the region with a large strain of the pre-forging. However, necklace-like mixed grain microstructure is formed in the region with a small strain of the pre-forging. In addition, when the microstructure before final deformation consists of mixed grains, dynamic recrystallization (DRX) nucleation behavior preferentially depends on kernel average misorientation (KAM) values. A large KAM can promote the formation of DRX nuclei. When the KAM values are close, a smaller average grain size of mixed-grain microstructure is more conductive to promote the DRX nucleation. Finally, the interaction mechanisms between δ phase and DRX nucleation are revealed.

Modeling Dynamic Recrystallization Behavior in a Novel HIPed P/M Superalloy during High-Temperature Deformation.

The dynamic recrystallization (DRX) features and the evolution of the microstructure of a new hot isostatic pressed (HIPed) powder metallurgy (P/M) superalloy are investigated by hot-compression tests. The sensitivity of grain dimension and DRX behavior to deformation parameters is analyzed. The results reveal that the DRX features and grain-growth behavior are significantly affected by deformation conditions. The DRX process is promoted with a raised temperature/true strain or a reduced strain rate. However, the grains grow up rapidly at relatively high temperatures. At strain rates of o.1 s-1 and 1 s-1, a uniform microstructure and small grains are obtained. Due to the obvious differences in the DRX rate at various temperatures, the piecewise DRX kinetics equations are proposed to predict the DRX behavior. At the same time, a mathematical model for predicting the grain dimension and the grain growth behavior is established. To further analyze the DRX behavior and the changes in grain dimension, the hot deformation process is simulated. The developed grain-growth equation as well as the piecewise DRX kinetics equations are integrated into DEFORM software. The simulated DRX features are consistent with the test results, indicating that the proposed DRX kinetics equations and the established grain-growth model can be well used for describing the microstructure evolution. So, they are very useful for the practical hot forming of P/M superalloy parts.