Evaluation of a field kit for testing arsenic in paddy soil contaminated by irrigation water.

Rice is the primary crop in Bangladesh and rice yield is diminished due to the buildup of arsenic (As) in soil from irrigation with high-As groundwater. Soil testing with an inexpensive kit could help farmers target high-As soil for mitigation or decide to switch to a different crop that is less sensitive to As in soil. A total of 3,240 field kit measurements of As in 0.5 g of fresh soil added to 50 mL of water were compared with total soil As concentrations measured on oven-dried homogenized soil by X-ray fluorescence (XRF). For sets of 12 soil samples collected within a series of rice fields, the average of kit As measurements was a linear function of the average of XRF measurements (r2=0.69). Taking into account that the kit overestimates water As concentrations by about a factor of two, the relationship suggests that about a quarter of the As in paddy soil is released in the kit's reaction vessel. Using the relationship and considering XRF measurements as the reference, the 12-sample average determined correctly whether soil As was above or below a 30 mg/kg threshold in 86% of cases where soil As was above the threshold and in 79% of cases where soil As was below the threshold. We also used a Bayesian approach using 12 kit measurements to estimate the probability that soil As was above a given threshold indicated by XRF measurements. The Bayesian approach is theoretically optimal but was only slightly more accurate than the linear regression. These results show that rice farmers can identify high-As portions of their fields for mitigation using a dozen field kit measurements on fresh soil and base their decisions on this information.

Effectiveness of Different Approaches to Arsenic Mitigation over 18 Years in Araihazar, Bangladesh: Implications for National Policy.

About 20 million rural Bangladeshis continue to drink well water containing >50 µg/L arsenic (As). This analysis argues for reprioritizing interventions on the basis of a survey of wells serving a population of 380,000 conducted one decade after a previous round of testing overseen by the government. The available data indicate that testing alone reduced the exposed population in the area in the short term by about 130,000 by identifying the subset of low As wells that could be shared at a total cost of 150 m) wells and a single piped-water supply system by the government reduced exposure of little more than 7000 inhabitants at a cost of US$150 per person whose exposure was reduced. The findings make a strong case for long-term funding of free well testing on a massive scale with piped water or groundwater treatment only as a last resort.

Inversion of High-Arsenic Soil for Improved Rice Yield in Bangladesh.

Rice is the primary crop in Bangladesh, and rice yield is diminished due to the buildup of arsenic (As) in soil from irrigation with high-As groundwater. Implementing a soil inversion, where deeper low-As soil is exchanged with the surface high-As soil in contact with rice roots, may mitigate the negative impacts of As on yield. We compared soil As, soil nutrients, and rice yield in control plots with those in adjacent soil inversion plots. We also estimated the quantity of soil As deposited on a yearly basis via irrigation water, to explore the longevity of a soil inversion to reduce surface As. Soil As, organic carbon, nitrogen, and phosphorus concentrations decreased by about 40% in response to the inversion and remained lowered over four seasons of monitoring. Inversion plot yields increased above control plot yields by 15-30% after a one-season lag despite the recovering but still reduced nutrient levels. Farmers have started conducting soil inversions of their own volition, typically close to where irrigation water enters the field. However, the yield gain will be limited to a few decades at most due to deposition of As via well water, unless the field is irrigated with low-As river or pond water.

Field Study of Rice Yield Diminished by Soil Arsenic in Bangladesh.

Rice was traditionally grown only during the summer (aman) monsoon in Bangladesh but more than half is now grown during the dry winter (boro) season and requires irrigation. A previous field study conducted in a small area irrigated by a single high-arsenic well has shown that the accumulation of arsenic (As) in soil from irrigating with high-As groundwater can reduce rice yield. We investigated the effect of soil As on rice yield under a range of field conditions by exchanging the top 15 cm of soil between 13 high-As and 13 low-As plots managed by 16 different farmers, and we explore the implications for mitigation. Soil As and rice yields were measured for soil replacement plots where the soil was exchanged and adjacent control plots where the soil was not exchanged. Differences in yield (ranging from +2 to -2 t/ha) were negatively correlated to the differences in soil As (ranging from -9 to +19 mg/kg) between adjacent replacement and control plots during two boro seasons. The relationship between soil As and yield suggests a boro rice yield loss over the entire country of 1.4-4.9 million tons annually, or 7-26% of the annual boro harvest, due to the accumulation of As in soil over the past 25 years.

Mechanism and design analysis of articulated ankle foot orthoses for drop-foot.

Robotic technologies are being employed increasingly in the treatment of lower limb disabilities. Individuals suffering from stroke and other neurological disorders often experience inadequate dorsiflexion during swing phase of the gait cycle due to dorsiflexor muscle weakness. This type of pathological gait, mostly known as drop-foot gait, has two major complications, foot-slap during loading response and toe-drag during swing. Ankle foot orthotic (AFO) devices are mostly prescribed to resolve these complications. Existing AFOs are designed with or without articulated joint with various motion control elements like springs, dampers, four-bar mechanism, series elastic actuator, and so forth. This paper examines various AFO designs for drop-foot, discusses the mechanism, and identifies limitations and remaining design challenges. Along with two commercially available AFOs some designs possess promising prospective to be used as daily-wear device. However, the design and mechanism of AFO must ensure compactness, light weight, low noise, and high efficiency. These entailments present significant engineering challenges to develop a new design with wide consumer adoption.

Modeling, control, and simulation of battery storage photovoltaic-wave energy hybrid renewable power generation systems for island electrification in Malaysia.

Today, the whole world faces a great challenge to overcome the environmental problems related to global energy production. Most of the islands throughout the world depend on fossil fuel importation with respect to energy production. Recent development and research on green energy sources can assure sustainable power supply for the islands. But unpredictable nature and high dependency on weather conditions are the main limitations of renewable energy sources. To overcome this drawback, different renewable sources and converters need to be integrated with each other. This paper proposes a standalone hybrid photovoltaic- (PV-) wave energy conversion system with energy storage. In the proposed hybrid system, control of the bidirectional buck-boost DC-DC converter (BBDC) is used to maintain the constant dc-link voltage. It also accumulates the excess hybrid power in the battery bank and supplies this power to the system load during the shortage of hybrid power. A three-phase complex vector control scheme voltage source inverter (VSI) is used to control the load side voltage in terms of the frequency and voltage amplitude. Based on the simulation results obtained from Matlab/Simulink, it has been found that the overall hybrid framework is capable of working under the variable weather and load conditions.

A fuzzy controller for lower limb exoskeletons during sit-to-stand and stand-to-sit movement using wearable sensors.

Human motion is a daily and rhythmic activity. The exoskeleton concept is a very positive scientific approach for human rehabilitation in case of lower limb impairment. Although the exoskeleton shows potential, it is not yet applied extensively in clinical rehabilitation. In this research, a fuzzy based control algorithm is proposed for lower limb exoskeletons during sit-to-stand and stand-to-sit movements. Surface electromyograms (EMGs) are acquired from the vastus lateralis muscle using a wearable EMG sensor. The resultant acceleration angle along the z-axis is determined from a kinematics sensor. Twenty volunteers were chosen to perform the experiments. The whole experiment was accomplished in two phases. In the first phase, acceleration angles and EMG data were acquired from the volunteers during both sit-to-stand and stand-to-sit motions. During sit-to-stand movements, the average acceleration angle at activation was 11°-48° and the EMG varied from -0.19 mV to +0.19 mV. On the other hand, during stand-to-sit movements, the average acceleration angle was found to be 57.5°-108° at the activation point and the EMG varied from -0.32 mV to +0.32 mV. In the second phase, a fuzzy controller was designed from the experimental data. The controller was tested and validated with both offline and real time data using LabVIEW.

Municipal solid waste management: Identification and analysis of technology selection criteria using Fuzzy Delphi and Fuzzy DEMATEL technique.

Municipal solid waste management (MSWM) poses a considerable challenge to developing countries like Bangladesh because of the rising waste generation rates and lack of effective management practices such as illegal open dumping and informal waste collection. One of the crucial factors in the successful management of MSW is to select the appropriate technology which is a complex multi-criteria and laborious process. Despite the global emphasis on the importance of MSWM in the literature, there is a lack of studies conducted in developing countries that effectively identify and analyze the critical performance criteria for appropriate technology selection. This research aims to address this shortcoming by identifying, and prioritizing the selection criteria and finally investigating the inter-relationship between them and the degree to which they affect or are affected by one another. First, a thorough literature review and expert consultation were employed to determine a set of 21 key criteria using the Fuzzy Delphi method (FDM). Later, taking into account the imprecise and subjective nature of the DEMATEL method on human judgements, the Fuzzy DEMATEL technique was employed to investigate the cause-effect relationships among the identified criteria. The findings of the study demonstrated that 14 criteria were categorized as causal elements that have the most significant influence on the MSWM technology selection process and 7 criteria were categorized as effect. The selection of MSWM technology demands greater consideration of the top three ranked criteria, namely T4- Access to Technology (AT), T8- Feasibility (F), and the Ec6-Infrastructure requirements (IR). By identifying the pertinent criteria, structures and interrelationships, the outcome of the study can facilitate a better understanding of causal relationships among the criteria that require specific consideration from the decision-makers and allow them to select appropriate MSW management technology.

Mass fluxes of dissolved arsenic discharging to the Meghna River are sufficient to account for the mass of arsenic in riverbank sediments.

Shallow (<30 m) reducing groundwater commonly contains abundant dissolved arsenic (As) in Bangladesh. We hypothesize that dissolved As in iron (Fe)-rich groundwater discharging to rivers is trapped onto Fe(III)-oxyhydroxides which precipitate in shallow riverbank sediments under the influence of tidal fluctuations. Therefore, the goal of this study is to compare the calculated mass of sediment-bound As that would be sequestered from dissolved groundwater As that discharges through riverbanks of the Meghna River to the observed mass of As trapped within riverbank sediments. To calculate groundwater discharge, a Boussinesq aquifer analytical groundwater flow model was developed and constrained by cyclical seasonal fluctuations in hydraulic heads and river stages observed at three sites along a 13 km reach in central Bangladesh. At all sites, groundwater discharges to the river year-round but most of it passes through an intertidal zone created by ocean tides propagating upstream from the Bay of Bengal in the dry season. The annualized groundwater discharge per unit width at the three sites ranges from 173 to 891 m2/yr (average 540 m2/yr). Assuming that riverbanks have been stable since the Brahmaputra River avulsed far away from this area 200 years ago and dissolved As is completely trapped within riverbank sediments, the mass of accumulated sediment As can be calculated by multiplying groundwater discharge by ambient aquifer As concentrations measured in 1969 wells. Across all sites, the range of calculated sediment As concentrations in the riverbank is 78-849 mg/kg, which is higher than the observed concentrations (17-599 mg/kg). This discovery supports the hypothesis that the dissolved As in groundwater discharge to the river is sufficient to account for the observed buried deposits of As along riverbanks.

Recommended Sampling Intervals for Arsenic in Private Wells.

Geogenic arsenic in drinking water is a worldwide problem. For private well owners, testing (e.g., private or government laboratory) is the main method to determine arsenic concentration. However, the temporal variability of arsenic concentrations is not well characterized and it is not clear how often private wells should be tested. To answer this question, three datasets, two new and one publicly available, with temporal arsenic data were utilized: 6370 private wells from New Jersey tested at least twice since 2002, 2174 wells from the USGS NAWQA database, and 391 private wells sampled 14 years apart from Bangladesh. Two arsenic drinking water standards are used for the analysis: 10 µg/L, the WHO guideline and EPA standard or maximum contaminant level (MCL) and 5 µg/L, the New Jersey MCL. A rate of change was determined for each well and these rates were used to predict the temporal change in arsenic for a range of initial arsenic concentrations below an MCL. For each MCL and initial concentration, the probability of exceeding an MCL over time was predicted. Results show that to limit a person to below a 5% chance of drinking water above an MCL, wells that are ½ an MCL and above should be tested every year and wells below ½ an MCL should be tested every 5 years. These results indicate that one test result below an MCL is inadequate to ensure long-term compliance. Future recommendations should account for temporal variability when creating drinking water standards and guidance for private well owners.

Similar retardation of arsenic in gray Holocene and orange Pleistocene sediments: Evidence from field-based column experiments in Bangladesh.

Groundwater flow has the potential to introduce arsenic (As) in previously uncontaminated aquifers. The extent to which As transport is retarded by adsorption is particularly relevant in Bangladesh where low-As wells offer the best chance of reducing chronic exposure to As of a large rural population dependent on groundwater. In this study, column experiments were conducted with intact cores in the field to measure As retardation. Freshly collected cores of reduced iron (Fe-II) dominated gray sediment of Holocene age as well as oxidized Fe (III)-coated orange sediment of Pleistocene age were eluted at pore-water velocities of 40-230 cm/day with anoxic groundwater pumped directly from a well and containing 320 µg/L As. Up to 100 µg/L As was immediately released from gray sand but the main As breakthrough for both gray and orange sand occurred between 30 and 70 pore volumes, depending on flow rate. The early release of As from gray sand is attributed to the presence of a weakly bound pool of As. The sorption of As was kinetically limited in both gray and orange sand columns. We used a reversible multi-reaction transport model to simulate As breakthrough curves while keeping the model parameters as constant as possible. Contrary to the notion that dissolved As is sorbed more strongly to orange sands, we show that As was similarly retarded in both gray and orange sands in the field.

Arsenic contamination of Bangladesh aquifers exacerbated by clay layers.

Confining clay layers typically protect groundwater aquifers against downward intrusion of contaminants. In the context of groundwater arsenic in Bangladesh, we challenge this notion here by showing that organic carbon drawn from a clay layer into a low-arsenic pre-Holocene (>12 kyr-old) aquifer promotes the reductive dissolution of iron oxides and the release of arsenic. The finding explains a steady rise in arsenic concentrations in a pre-Holocene aquifer below such a clay layer and the repeated failure of a structurally sound community well. Tritium measurements indicate that groundwater from the affected depth interval (40-50 m) was recharged >60 years ago. Deeper (55-65 m) groundwater in the same pre-Holocene aquifer was recharged only 10-50 years ago but is still low in arsenic. Proximity to a confining clay layer that expels organic carbon as an indirect response to groundwater pumping, rather than directly accelerated recharge, caused arsenic contamination of this pre-Holocene aquifer.

Microbial Community Structure and Arsenic Biogeochemistry in Two Arsenic-Impacted Aquifers in Bangladesh.

Long-term exposure to trace levels of arsenic (As) in shallow groundwater used for drinking and irrigation puts millions of people at risk of chronic disease. Although microbial processes are implicated in mobilizing arsenic from aquifer sediments into groundwater, the precise mechanism remains ambiguous. The goal of this work was to target, for the first time, a comprehensive suite of state-of-the-art molecular techniques in order to better constrain the relationship between indigenous microbial communities and the iron and arsenic mineral phases present in sediments at two well-characterized arsenic-impacted aquifers in Bangladesh. At both sites, arsenate [As(V)] was the major species of As present in sediments at depths with low aqueous As concentrations, while most sediment As was arsenite [As(III)] at depths with elevated aqueous As concentrations. This is consistent with a role for the microbial As(V) reduction in mobilizing arsenic. 16S rRNA gene analysis indicates that the arsenic-rich sediments were colonized by diverse bacterial communities implicated in both dissimilatory Fe(III) and As(V) reduction, while the correlation analyses involved phylogenetic groups not normally associated with As mobilization. Findings suggest that direct As redox transformations are central to arsenic fate and transport and that there is a residual reactive pool of both As(V) and Fe(III) in deeper sediments that could be released by microbial respiration in response to hydrologic perturbation, such as increased groundwater pumping that introduces reactive organic carbon to depth.IMPORTANCE The consumption of arsenic in waters collected from tube wells threatens the lives of millions worldwide and is particularly acute in the floodplains and deltas of southern Asia. The cause of arsenic mobilization from natural sediments within these aquifers to groundwater is complex, with recent studies suggesting that sediment-dwelling microorganisms may be the cause. In the absence of oxygen at depth, specialist bacteria are thought able to use metals within the sediments to support their metabolism. Via these processes, arsenic-contaminated iron minerals are transformed, resulting in the release of arsenic into the aquifer waters. Focusing on a field site in Bangladesh, a comprehensive, multidisciplinary study using state-of-the-art geological and microbiological techniques has helped better understand the microbes that are present naturally in a high-arsenic aquifer and how they may transform the chemistry of the sediment to potentially lethal effect.

Technical Study of a Standalone Photovoltaic-Wind Energy Based Hybrid Power Supply Systems for Island Electrification in Malaysia.

Energy is one of the most important factors in the socioeconomic development of a country. In a developing country like Malaysia, the development of islands is mostly related to the availability of electric power. Power generated by renewable energy sources has recently become one of the most promising solutions for the electrification of islands and remote rural areas. But high dependency on weather conditions and the unpredictable nature of these renewable energy sources are the main drawbacks. To overcome this weakness, different green energy sources and power electronic converters need to be integrated with each other. This study presents a battery storage hybrid standalone photovoltaic-wind energy power supply system. In the proposed standalone hybrid system, a DC-DC buck-boost bidirectional converter controller is used to accumulates the surplus hybrid power in the battery bank and supplies this power to the load during the hybrid power shortage by maintaining the constant dc-link voltage. A three-phase voltage source inverter complex vector control scheme is used to control the load side voltage in terms of the voltage amplitude and frequency. Based on the simulation results obtained from MATLAB/Simulink, it has been found that the overall hybrid framework is capable of working under variable weather and load conditions.