RESUMEN
In this work, enzymatic doped/undoped poly-silicon nanowire sensors with different lengths were fabricated using a top-down technique to measure glucose concentration. The sensitivity and resolution of these sensors correlate well with the dopant property and length of nanowire. Experimental results indicate that the resolution is proportional to the nanowire length and dopant concentration. However, the sensitivity is inversely proportional to the nanowire length. The optimum resolution can be better than 0.02 mg/dL for a doped type sensor with length of 3.5 µm. Furthermore, the proposed sensor was demonstrated for 30 applications with similar current-time response and showed good repeatability.
Asunto(s)
Nanocables , Silicio , GlucosaRESUMEN
A design method and corresponding fabrication procedures are proposed for a dual frusto-conical reflector of a downlight luminaire. The profile of the dual frusto-conical reflector consists of two flat-slant reflective surfaces with slightly different slopes. The optimum dual frusto-conical reflector can be obtained with the proposed design method. The finished product of the dual frusto-conical reflector is fabricated by a 3D printer and followed by surface polishing and reflection paint spraying. The measurement results show that luminaires exhibited 70% optimum illuminance confined within an illumination area of 1.8m2, and the optimum illumination intensity is at 252 lux. The optimum efficiency of the proposed luminaire can reach 158 lm/W for normal-white light-emitting diode (LED) and 119 lm/W for warm-white LED, respectively.
RESUMEN
A three-axis micro magnetic sensor (MS) is developed based on the standard 180 nm complementary metal oxide semiconductor (CMOS) technology. The MS designs two magnetic sensing elements (MSEs), which consists of an x/y-MSE and an z-MSE, to reduce cross-sensitivity. The x/y-MSE is constructed by an x-MSE and an y-MSE that are respectively employed to detect in the x- and y-direction magnetic field (MF). The z-MSE is used to sense in the z-direction MF. The x/y-MSE, which is constructed by two magnetotransistors, designs four additional collectors that are employed to increase the sensing current and to enhance the sensitivity of the MS. The Sentaurus TCAD software simulates the characteristic of the MS. The measured results reveal that the MS sensitivity is 534 mV/T in the x-direction MF, 525 mV/T in the y-direction MF and 119 mV/T in the z-axis MF.
Asunto(s)
Óxidos , Semiconductores , Campos Magnéticos , Programas Informáticos , TecnologíaRESUMEN
A radio frequency microelectromechanical system switch (MSS) manufactured by the complementary metal oxide semiconductor (CMOS) process is presented. The MSS is a capacitive shunt type. Structure for the MSS consists of coplanar waveguide (CPW) lines, a membrane, and springs. The membrane locates over the CPW lines. The surface of signal line for the CPW has a silicon dioxide dielectric layer. The fabrication of the MSS contains a CMOS process and a post-process. The MSS has a sacrificial oxide layer after the CMOS process. In the post-processing, a wet etching of buffer oxide etch (BOE) etchant is employed to etch the sacrificial oxide layer, so that the membrane is released. Actuation voltage for the MSS is simulated using the CoventorWare software. The springs have a low stiffness, so that the actuation voltage reduces. The measured results reveal that actuation voltage for the MSS is 10 V. Insertion loss for the MSS is 0.9 dB at 41 GHz and isolation for the MSS is 30 dB at 41 GHz.
RESUMEN
The fabrication and characterization of a magnetic micro sensor (MMS) with two magnetic field effect transistors (MAGFETs) based on the commercial complementary metal oxide semiconductor (CMOS) process are investigated. The magnetic micro sensor is a three-axis sensing type. The structure of the magnetic microsensor is composed of an x/y-MAGFET and a z-MAGFET. The x/y-MAGFET is employed to sense the magnetic field (MF) in the x- and y-axis, and the z-MAGFET is used to detect the MF in the z-axis. To increase the sensitivity of the magnetic microsensor, gates are introduced into the two MAGFETs. The sensing current of the MAGFET enhances when a bias voltage is applied to the gates. The finite element method software Sentaurus TCAD was used to analyze the MMS's performance. Experiments show that the MMS has a sensitivity of 182 mV/T in the x-axis MF and a sensitivity of 180 mV/T in the y-axis MF. The sensitivity of the MMS is 27.8 mV/T in the z-axis MF.
RESUMEN
Tapping mode (TM) atomic force microscopy (AFM) in a liquid environment is widely used to measure the contours of biological specimens. The TM triggers the AFM probe approximately at the resonant frequencies and controls the tip such that it periodically touches the specimen along the scanning path. The AFM probe and its tip produce a hydrodynamic pressure on the probe itself and press the specimen. The tip to specimen size ratio is known to affect the measurement accuracy of AFM, however, few studies have focused on the hydrodynamic pressure caused by the effects of specimen size. Such pressure affects the contour distortion of the biological specimen. In this study, a semi-analytical method is employed for a semicircular specimen to analyze the vorticity and pressure distributions for specimens of various sizes and at various tip locations. Changes in pressure distribution, fluid spin motion, and specimen deformation are identified as the tip approaches the specimen. The results indicate the following: the specimen surface experiences the highest pressure when the specimen diameter equals the tip width; the vorticity between tip and specimen is complex when the tip is close to the specimen center line; and the specimen inflates when the tip is aligned with the specimen center line.
RESUMEN
The design and fabrication of an ethanol microsensor integrated with a readout circuit on-a-chip using the complementary metal oxide semiconductor (CMOS)-microelectro -mechanical system (MEMS) technique are investigated. The ethanol sensor is made up of a heater, a sensitive film and interdigitated electrodes. The sensitive film is tin dioxide that is prepared by the sol-gel method. The heater is located under the interdigitated electrodes, and the sensitive film is coated on the interdigitated electrodes. The sensitive film needs a working temperature of 220 °C. The heater is employed to provide the working temperature of sensitive film. The sensor generates a change in capacitance when the sensitive film senses ethanol gas. A readout circuit is used to convert the capacitance variation of the sensor into the output frequency. Experiments show that the sensitivity of the ethanol sensor is 0.9 MHz/ppm.
RESUMEN
A methanol microsensor integrated with a micro heater manufactured using the complementary metal oxide semiconductor (CMOS)-microelectromechanical system (MEMS) technique was presented. The sensor has a capability of detecting low concentration methanol gas. Structure of the sensor is composed of interdigitated electrodes, a sensitive film and a heater. The heater located under the interdigitated electrodes is utilized to provide a working temperature to the sensitive film. The sensitive film prepared by the sol-gel method is tin dioxide doped cadmium sulfide, which is deposited on the interdigitated electrodes. To obtain the suspended structure and deposit the sensitive film, the sensor needs a post-CMOS process to etch the sacrificial silicon dioxide layer and silicon substrate. The methanol senor is a resistive type. A readout circuit converts the resistance variation of the sensor into the output voltage. The experimental results show that the methanol sensor has a sensitivity of 0.18 V/ppm.
Asunto(s)
Metanol/química , Sistemas Microelectromecánicos/métodos , Compuestos de Cadmio/química , Óxidos/química , Sulfuros/químicaRESUMEN
The fabrication and characterization of a radio frequency (RF) micromachined switch with annealing were presented. The structure of the RF switch consists of a membrane, coplanar waveguide (CPW) lines, and eight springs. The RF switch is manufactured using the complementary metal oxide semiconductor (CMOS) process. The switch requires a post-process to release the membrane and springs. The post-process uses a wet etching to remove the sacrificial silicon dioxide layer, and to obtain the suspended structures of the switch. In order to improve the residual stress of the switch, an annealing process is applied to the switch, and the membrane obtains an excellent flatness. The finite element method (FEM) software CoventorWare is utilized to simulate the stress and displacement of the RF switch. Experimental results show that the RF switch has an insertion loss of 0.9 dB at 35 GHz and an isolation of 21 dB at 39 GHz. The actuation voltage of the switch is 14 V.
Asunto(s)
Ondas de Radio , Programas Informáticos , Análisis de Elementos Finitos , SemiconductoresRESUMEN
The modeling and fabrication of a magnetic microsensor based on a magneto-transistor were presented. The magnetic sensor is fabricated by the commercial 0.18 mm complementary metal oxide semiconductor (CMOS) process without any post-process. The finite element method (FEM) software Sentaurus TCAD is utilized to analyze the electrical properties and carriers motion path of the magneto-transistor. A readout circuit is used to amplify the voltage difference of the bases into the output voltage. Experiments show that the sensitivity of the magnetic sensor is 354 mV/T at the supply current of 4 mA.
RESUMEN
The study develops an integrated humidity microsensor fabricated using the commercial 0.18 µm complementary metal oxide semiconductor (CMOS) process. The integrated humidity sensor consists of a humidity sensor and a ring oscillator circuit on-a-chip. The humidity sensor is composed of a sensitive film and branch interdigitated electrodes. The sensitive film is zinc oxide prepared by sol-gel method. After completion of the CMOS process, the sensor requires a post-process to remove the sacrificial oxide layer and to coat the zinc oxide film on the interdigitated electrodes. The capacitance of the sensor changes when the sensitive film adsorbs water vapor. The circuit is used to convert the capacitance of the humidity sensor into the oscillation frequency output. Experimental results show that the output frequency of the sensor changes from 84.3 to 73.4 MHz at 30 °C as the humidity increases 40 to 90%RH.
Asunto(s)
Conductometría/instrumentación , Electrodos , Humedad , Oscilometría/instrumentación , Semiconductores , Transductores , Agua/análisis , Diseño de Equipo , Análisis de Falla de Equipo , Miniaturización , Transición de Fase , Integración de SistemasRESUMEN
A humidity microsensor integrated with a readout circuit on-a-chip fabricated using the commercial 0.18 µm CMOS (complementary metal oxide semiconductor) process was presented. The integrated sensor chip consists of a humidity sensor and a readout circuit. The humidity sensor is composed of a sensitive film and interdigitated electrodes. The sensitive film is titanium dioxide prepared by the sol-gel method. The titanium dioxide is coated on the interdigitated electrodes. The humidity sensor requires a post-process to remove the sacrificial layer and to coat the titanium dioxide. The resistance of the sensor changes as the sensitive film absorbs or desorbs vapor. The readout circuit is employed to convert the resistance variation of the sensor into the output voltage. The experimental results show that the integrated humidity sensor has a sensitivity of 4.5 mV/RH% (relative humidity) at room temperature.
RESUMEN
This study investigates the fabrication and characterization of an acetone microsensor with a ring oscillator circuit using the commercial 0.18 µm complementary metal oxide semiconductor (CMOS) process. The acetone microsensor contains a sensitive material, interdigitated electrodes and a polysilicon heater. The sensitive material is α-Fe2O3 synthesized by the hydrothermal method. The sensor requires a post-process to remove the sacrificial oxide layer between the interdigitated electrodes and to coat the α-Fe2O3 on the electrodes. When the sensitive material adsorbs acetone vapor, the sensor produces a change in capacitance. The ring oscillator circuit converts the capacitance of the sensor into the oscillation frequency output. The experimental results show that the output frequency of the acetone sensor changes from 128 to 100 MHz as the acetone concentration increases 1 to 70 ppm.
Asunto(s)
Acetona/química , Diseño de Equipo/instrumentación , Óxidos/química , Semiconductores , Capacidad Eléctrica , Electrodos , Compuestos Férricos/química , Gases/químicaRESUMEN
This study investigates the design and fabrication of magnetic microsensors using the commercial 0.35 µm complementary metal oxide semiconductor (CMOS) process. The magnetic sensor is composed of springs and interdigitated electrodes, and it is actuated by the Lorentz force. The finite element method (FEM) software CoventorWare is adopted to simulate the displacement and capacitance of the magnetic sensor. A post-CMOS process is utilized to release the suspended structure. The post-process uses an anisotropic dry etching to etch the silicon dioxide layer and an isotropic dry etching to remove the silicon substrate. When a magnetic field is applied to the magnetic sensor, it generates a change in capacitance. A sensing circuit is employed to convert the capacitance variation of the sensor into the output voltage. The experimental results show that the output voltage of the magnetic microsensor varies from 0.05 to 1.94 V in the magnetic field range of 5-200 mT.
RESUMEN
The study presents an ammonia microsensor integrated with a readout circuit on-a-chip fabricated using the commercial 0.18 µm complementary metal oxide semiconductor (CMOS) process. The integrated sensor chip consists of a heater, an ammonia sensor and a readout circuit. The ammonia sensor is constructed by a sensitive film and the interdigitated electrodes. The sensitive film is zirconium dioxide that is coated on the interdigitated electrodes. The heater is used to provide a working temperature to the sensitive film. A post-process is employed to remove the sacrificial layer and to coat zirconium dioxide on the sensor. When the sensitive film adsorbs or desorbs ammonia gas, the sensor produces a change in resistance. The readout circuit converts the resistance variation of the sensor into the output voltage. The experiments show that the integrated ammonia sensor has a sensitivity of 4.1 mV/ppm.
Asunto(s)
Amoníaco/química , Dispositivos Laboratorio en un Chip , Semiconductores , Circonio/química , Electrodos , Gases/química , TemperaturaRESUMEN
The study investigates the fabrication and characterization of an ethanol microsensor equipped with a heater. The ethanol sensor is manufactured using the commercial 0.18 µm complementary metal oxide semiconductor (CMOS) process. The sensor consists of a sensitive film, a heater and interdigitated electrodes. The sensitive film is zinc oxide prepared by the sol-gel method, and it is coated on the interdigitated electrodes. The heater is located under the interdigitated electrodes, and it is used to supply a working temperature to the sensitive film. The sensor needs a post-processing step to remove the sacrificial oxide layer, and to coat zinc oxide on the interdigitated electrodes. When the sensitive film senses ethanol gas, the resistance of the sensor generates a change. An inverting amplifier circuit is utilized to convert the resistance variation of the sensor into the output voltage. Experiments show that the sensitivity of the ethanol sensor is 0.35 mV/ppm.
Asunto(s)
Conductometría/instrumentación , Electrodos , Etanol/análisis , Calefacción/instrumentación , Semiconductores , Impedancia Eléctrica , Diseño de Equipo , Análisis de Falla de Equipo , Etanol/química , Miniaturización , TransductoresRESUMEN
This paper presents the fabrication and characterization of energy harvesting thermoelectric micro generators using the commercial complementary metal oxide semiconductor (CMOS) process. The micro generator consists of 33 thermocouples in series. Thermocouple materials are p-type and n-type polysilicon since they have a large Seebeck coefficient difference. The output power of the micro generator depends on the temperature difference in the hot and cold parts of the thermocouples. In order to increase this temperature difference, the hot part of the thermocouples is suspended to reduce heat-sinking. The micro generator needs a post-CMOS process to release the suspended structures of hot part, which the post-process includes an anisotropic dry etching to etch the sacrificial oxide layer and an isotropic dry etching to remove the silicon substrate. Experiments show that the output power of the micro generator is 9.4 mW at a temperature difference of 15 K.
RESUMEN
The design, fabrication, and measurement of a microelectromechanical system (MEMS) three-axis magnetic field sensor (MFS) based on the commercial complementary metal oxide semiconductor (CMOS) process are investigated. The MFS is a magnetic transistor type. The performance of the MFS was analyzed employing the semiconductor simulation software, Sentaurus TCAD. In order to decrease the cross-sensitivity of the three-axis MFS, the structure of the MFS is planed to accommodate two independent sensing components, a z-MFS utilized to sense magnetic field (M-F) in the z-direction and a y/x-MFS composed of a y-MFS and a x-MFS to be utilized to sense M-F in the y- and x-directions. The z-MFS incorporates four additional collectors to increase its sensitivity. The commercial 1P6M 0.18 µm CMOS process of the Taiwan Semiconductor Manufacturing Company (TSMC) is utilized to manufacture the MFS. Experiments depict that the MFS has a low cross-sensitivity of less than 3%. The sensitivities of z-, y-, and x-MFS are 237 mV/T, 485 mV/T, and 484 mV/T, respectively.
RESUMEN
This study develops a TEMH (thermoelectric energy micro harvester) chip utilizing a commercial 0.18 µm CMOS (complementary metal oxide semiconductor) process. The chip contains a TEMH and temperature sensors. The TEMH is established using a series of 54 thermocouples. The use of the temperature sensors monitors the temperature of the thermocouples. One temperature sensor is set near the cold part of the thermocouples, and the other is set near the hot part of the thermocouples. The performance of the TEMH relies on the TD (temperature difference) at the CHP (cold and hot parts) of the thermocouples. The more the TD at the CHP of the thermocouples increases, the higher the output voltage and output power of the TEMH become. To obtain a higher TD, the cold part of the thermocouples is designed as a suspended structure and is combined with cooling sheets to increase heat dissipation. The cooling sheet is constructed of a stack of aluminum layers and is mounted above the cold part of the thermocouple. A finite element method software, ANSYS, is utilized to compute the temperature distribution of the TEMH. The TEMH requires a post-process to obtain the suspended thermocouple structure. The post-process utilizes an RIE (reactive ion etch) to etch the two sacrificial materials, which are silicon dioxide and silicon substrate. The results reveal that the structure of the thermocouples is completely suspended and does not show any injury. The measured results reveal that the output voltage of the TEMH is 32.5 mV when the TD between the CHP of the thermocouples is 4 K. The TEMH has a voltage factor of 8.93 mV/mm2K. When the TD between the CHP of the thermocouples is 4 K, the maximum output power of the TEMH is 4.67 nW. The TEMH has a power factor of 0.31 nW/mm2K2.
RESUMEN
In intelligent manufacturing and robotic technology, various sensors must be integrated with equipment. In addition to traditional sensors, stretchable sensors are particularly attractive for applications in robotics and wearable devices. In this study, a piezoresistive stretchable strain sensor based on laser-induced graphene (LIG) was proposed and developed. A three-dimensional, porous LIG structure fabricated from polyimide (PI) film using laser scanning was used as the sensing layer of the strain sensor. Two LIG pattern structures (parallel and vertical) were fabricated and integrated within the LIG strain sensors. Scanning electron microscopy, an X-ray energy dispersive spectrometer, and Raman scattering spectroscopy were used to examine the microstructure of the LIG sensing layer. The performance and strain sensing properties of the parallel and vertical stretchable LIG strain sensors were investigated in tensile tests. The relative resistance changes and the gauge factors of the parallel and vertical LIG strain sensors were quantified. The parallel strain sensor achieved a high gauge factor of 15.79 in the applied strain range of 10% to 20%. It also had high sensitivity, excellent repeatability, good durability, and fast response times during the tensile experiments. The developed LIG strain sensor can be used for the real-time monitoring of human motions such like finger bending, wrist bending, and throat swallowing.