Health risks of inhalation exposure to BTEX in a municipal wastewater treatment plant in Middle East city: Shiraz, Iran.

Benzene, toluene, ethylbenzene, and xylene, known as BTEX, adversely affect human health. This study aimed to measure BTEX concentration and assess the health risk through inhalation exposure to these compounds in a municipal wastewater treatment plant. The ambient air samples were collected using the active sampling method in summer and winter. Sampling sites were close to wastewater treatment units, including bar screen & grit chamber (Site-1), aeration tank & secondary clarifiers (Site-2), anaerobic sludge digester (Site-3), and office & control building (Site-4). Results indicate that the mean levels of benzene and toluene in winter were higher than in summer. The levels of benzene and toluene were below the occupational exposure levels of the American Conference of Governmental Industrial Hygienists (ACGIH) and Occupational Safety and Health Administration (OSHA). The carcinogenic risk (CR) and hazard quotient (HQ) were assessed using the United States Environmental Protection Agency (U.S.EPA) method, and Monte Carlo simulation (MCS) was applied to quantify the uncertainty and sensitivity analysis. The CRs for all sampling sites were below the U.S.EPA threshold limit (1.0 × 10-4). The HQ values for benzene nearby Site-2 were above 1.0, indicating inhalation exposure could pose a health hazard. Besides, the HQ results for exposure to toluene in all sampling sites were less than 1.0. The sensitivity analysis had shown that the risk determinant for carcinogenic and non-carcinogenic risk was exposure time, followed by concentration.

Health risk assessment of exposure to atrazine in the soil of Shiraz farmlands, Iran.

Atrazine-contaminated soils can pose a carcinogenic and non-carcinogenic health risk through different routes for exposed people. This study aimed to assess the health risk of exposure to atrazine-contaminated soils through direct ingestion and dermal contact in farmlands nearby Shiraz. Atrazine concentration was measured in 22 selected sites using grid sampling. The carcinogenic and non-cancer risks associated with dermal and ingestion exposure in children and adults were estimated. The lowest and highest atrazine concentrations were in S1 (0.015 mg/kg soil) and S22 (0.55 mg/kg soil). Hazard Index (HI)1 values ranged from 0.007 to 0.25 for children, and the values ranged from 0.0008 to 0.03 for adults. The mean cancer risk for children and adults was 6.01 × 10-4 and 7.40 × 10-5, respectively. The HI value was less than 1 for all sampling sites, indicating that exposure to atrazine does not threaten children and adults. However, the cancer risk exceeds the United States Environmental Protection Agency (US.EPA)2 threshold risk limit (10-6 to 10-4) in all sampling sites. Therefore, it is recommended that children should avoid playing on atrazine-contaminated farms or soils near anywhere atrazine may have been used.

Comparative photo-oxidative degradation of etodolac, febuxostat and imatinib mesylate by UV-C/H2O2 and UV-C/S2O82- processes: Modeling, treatment optimization and biodegradability enhancement.

The pharmaceutical contamination in aquatic environment has arisen increasing concern due to its potentially chronic toxicity. In recent years, HO° and SO4°- based advanced oxidation processes (AOPs) have been widely applied in water and wastewater treatments due to their highly efficiency on contaminant removal. Here, the response surface modeling (RSM) was used to investigate the degradation of three typical pharmaceuticals (i.e., etodolac (ETD), febuxostat (FBU) and imatinib mesylate (IMT)) by UV/H2O2 and UV/S2O82- processes. Based on the multiple regression analysis on full factorial design matrix and calculated reaction rate constants, the RSM was built. The experimental rate constants under optimal conditions were quite close to those obtained from the model, implying the good fit of the RSM. In addition, the RSM results indicated that UV/S2O82- process was less sensitive to pH in comparison to the UV/H2O2 process on target contaminant removal. Finally, it showed that UV/S2O82- process was superior to the UV/H2O2 process to on the enhancement of target contaminant biodegradability.

A process mining approach in big data analysis and modeling decision making risks for measuring environmental health in institutions.

This paper aimed to introduce a process-mining framework for measuring the status of environmental health in institutions. The methodology developed a new software-based index namely Institutional Environmental Health Index (IEHI) that was integrated from ontology-based Multi-Criteria Group Decision-Making models based on the principles of fuzzy modeling and consensus evaluation. Fuzzy Ordered Weighting Average (OWA) with the capability of modeling the uncertainties and decision-making risks along with Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) were employed as the computation engine. The performance of the extended index was examined through an applied example on 20 mosques as public institutions. IEHI could analyze big data collected by environmental health investigators and convert them to a single and interpretable number. The index detected the mosques with very unsuitable health conditions that should be in priority of sanitation and suitable ones as well. Due to the capability of defining the type and numbers of criteria and benefitting from specific and user-friendly software namely Group Fuzzy Decision-Making, this index is highly flexible and practical. The methodology could be used for numerating the environmental health conditions in any intended institution or occupation. The proposed index would provide e-health assessment by more efficient analysis of big data and risks that make more realistic decisions in environmental health system.

Determination of chloroform concentration and human exposure assessment in the swimming pool.

This cross-sectional study aimed to examine the concentration of the by-products of chlorination in the swimming pool and estimate human health risk for the swimmers of Shiraz University of Medical Sciences. In this study, the chloroform concentrations of 16 samples were measured using Gas Chromatography (GC). All the measured concentrations were less than the allowed amount announced by the World Health Organization (WHO). The results of the cancer risk (CR) and hazard index (HI) showed that the major exposure routes were found to be dermal during swimming and the 95 percentile of estimated CR and HI for the male group were 1.38 × 10-10 and 1.82 × 10-5 respectively, which is higher than the values of 5.48 × 10-10 and 2.25 × 10-5 respectively, for the women group. Sensitivity analyses indicated that the swimming exposure time (ET), and chloroform concentration were the most relevant variables in the health risk model. Therefore, knowledge about the sources of micro-pollutants in swimming pools might help promote the health methods of the pool environment.

Exposure to polycyclic aromatic hydrocarbon-induced oxidative stress in Shiraz, Iran: urinary levels, health risk assessment and mediation effect of MDA on the risk of metabolic syndromes.

PURPOSE: Polycyclic Aromatic Hydrocarbons (PAHs) have been identified as carcinogenic and endocrine disrupter compounds that cause Metabolic Syndrome (MetS). Oxidative stress can lead to carcinogenesis and MetS in exposed people. Therefore, the relationship between urinary metabolite of PAH (OH-PAHs) level and the oxidative stress biomarker (Malondialdehyde) effect as the mediator in increasing the risk of MetS due to PAH exposure and risk assessment was investigated in Shiraz, Iran. METHODS: The first morning void urinary and blood samples were obtained from participants and analyzed. Physical examinations and anthropometric measurements were performed on the day of sampling. An automatic biochemistry analyzer was used to measure the blood cells. The participants' socio-demographic information was gathered using a questionnaire and direct interviews with participants. RESULTS: The MetS prevalence was 26%. Malondialdehyde could act as a mediator between exposure to 1-HydroxyPyrene and increase in fast blood sugar, exposure to 2-HydroxyNaphthalene and increase in systolic blood pressure and exposure to 2-HydroxyFluorene and increase in SBP. Hazard quotients varied from 0.009 to 14.92 in women, and from 0.005 to 8.43 for Fluorene and Naphthalene in men, respectively. The Hazard Indexes were greater than one meaning that the non-cancer health risk related to the PAH exposure could be identified in the participants. CONCLUSION: Although oxidative stress has been suggested to lead to MetS and the high HI levels obtained in the current study, future researches are essential to achieve more reliable findings and monitoring the environmental influencing factors in PAH exposure.

Exposure to polycyclic aromatic hydrocarbon-induced oxidative stress in individuals living near restaurants: a cross-sectional study in Shiraz, Iran.

Polycyclic aromatic hydrocarbons are environmental pollutants caused by the incomplete combustion of organic matter. The aim of this study was to investigate the concentration of urinary PAHs and their health effects in individuals living near restaurants. This cross-sectional study was done on 57 individuals who were living near 36 restaurants, and 30 individuals as the control group. Five urinary metabolites of PAHs (1-OH pyrene, 1-OH naphthalene, 2-OH naphthalene, 2-OH fluorine, and 9-OH phenanthrenen) were monitored. The total anti-oxidation capacity (TAC), malondialdehyde (MDA), C-reactive protein (CRP), and creatinine were also measured. The mean concentration of the sum of urinary PAHs (ΣOH-PAHs) was 1973.7, and 1687.61 ng/g creatinine in people living near restaurants and control group, respectively. Among the metabolites, the highest mean concentration was related to 1-OH Pyrene in the two study groups. In the individuals living near restaurants, the concentration of PAH metabolites was directly related to MDA and TAC (p < 0.05 for both). The present study findings revealed no significant correlation between PAH metabolites and CRP in the two study groups (P > 0.05). People living near restaurants are more exposed to components in cooking fumes, which may adversely affect their health. Further researches are required to elucidate the effect of PAHs exposure on these individuals' health status.

Photocatalytic degradation of 2,4-dichlorophenoxyacetic acid from aqueous solutions by Ag3PO4/TiO2 nanoparticles under visible light: kinetic and thermodynamic studies.

Between the countless chemical substances applied in agriculture, 2,4-dichlorophenoxyacetic acid (2,4-D) herbicide is considered as a toxic and carcinogenic pollutant which is difficult to remove from water due to its biological and chemical stability and high solubility. The goal of this study was photocatalytic degradation of 2,4-D, using Ag3PO4/TiO2 nanoparticles under visible light. The Ag3PO4/TiO2 nanoparticles were characterized using XRD, FESEM and EDS analysis to investigate its crystal structure and elemental compounds. The effect of operating parameters such as pH, contact time, catalyst dose, and initial concentration of herbicide on the efficiency of the process was studied. Increasing the pH and initial concentration of herbicide led to the reduction of the efficiency of removing the herbicide, while increasing contact time and catalyst dose increased the efficiency. The best result (98.4% removal efficiency) was achieved at pH = 3, 1 g/L catalyst dose, 60 min contact time, and 10 mg/L initial concentration of 2,4-D. According to the results, 2,4-D removal efficiency with Ag3PO4/TiO2 photocatalyst reached 96.1% from 98.4% after 5 cycles of reaction. The pseudo-first-order kinetics was the best fit for the 2,4-D degradation by Ag3PO4/TiO2 with correlation coefficients (R2 = 0.9945). The results demonstrated that the photocatalytic process using Ag3PO4/TiO2 nanoparticles in the presence of visible light had a relatively good efficiency in removing 2,4-D. Moreover, Ag3PO4/TiO2 can be used as a reusable photocatalyst for the degradation of such toxins from polluted water and wastewater.

Investigating the relationship between synergistic effects and diversity of four widely used agricultural pesticides by using bacterial species in liquid culture medium.

Interactive effects of mixtures of pesticides on bacteria are rarely investigated. The aim of this study was to investigate the cumulative, synergistic, and antagonistic effects of four widely used agricultural pesticides including deltamethrin, diazinon, chlorpyrifos, and 2,4-dichlorophenoxyacetic acid (2,4-D) on Pseudomonas, Aeromonas, and Bacillus bacteria. The reduction of alamar blue, as an indicator of bacterial activity, was measured using a spectrophotometer at 600-nm wavelength. Data were analyzed using SPSS 24.0 software. The binary mixtures of pesticides had mainly antagonistic and additive effects, but quadruple mixtures of pesticides had synergistic effects on all of the three bacterial species. In the mixtures of pesticides, increasing the number of compounds leads to more synergistic effects.

Changing face of Candida colonization pattern in pediatric patients with hematological malignancy during repeated hospitalizations, results of a prospective observational study (2016-2017) in shiraz, Iran.

BACKGROUND: Surveillance of current changes in the epidemiology of Invasive Fungal Diseases (IFDs) as an important component of the antifungal stewardship programs (ASP), requires careful regular monitoring, especially in high-risk settings such as oncology centers. This study aimed to examine Candida colonization status and corresponding current changes in children with malignancy during repeated admissions and also investigate the possible epidemiological shifts after the implementation of ASP. METHODS: In this prospective observational study, all eligible patients younger than 18 years were recruited during 2016-2017 at Amir Medical Oncology Center (AMOC) in Shiraz, Iran. Totally, 136 patients were enrolled and 482 samples were collected from different sites (oral/nasal discharges, urine and stool). Weekly regular sampling was carried out during hospitalization. Candida colonization status and epidemiological changes were monitored during repeated admissions. Samples were cultivated on Sabouraud Dextrose agar medium and identified by Polymerase Chain Reaction -Restriction Fragment Length Polymorphism (PCR-RFLP). RESULTS: Estimated Candida colonization incidence was 59.9% (82/136) in our patients. Candida colonization was found to be higher in oral cavity and rectum than that in nasal cavity. Among those long-term follow ups and repetitive hospitalizations, a significant number of patients exhibited changes in their colonization patterns (37.7%). Candida colonization did not reveal any significant relationship with age, sex, oncologic diseases and degree of neutropenia. C. albicans (72.0%) was found as the most common Candida species in colonized patients, followed by C. krusei, C. kefyr, C. glabrata and C. parapsilosis. CONCLUSION: Given the high incidence of Candida infections in children with cancers, close monitoring of epidemiologic changes is essential for judicious management, based on local surveillance data and improvement of overall quality of care in high risk patients.

Root structural changes of two remediator plants as the first defective barrier against industrial pollution, and their hyperaccumulation ability.

In the present day, plants are increasingly being utilized to safeguard the environment. In this study, we used Salsola crassa M. B. and Suaeda maritima L. Dumort for phytoremediation of water contaminated with heavy metals and simultaneous examination of the effect of industrial pollution on their root structures. After irrigation of a treatment group with wastewater and a control group with fresh water for 3 months, we fixed the root parts in the FAA fixator for developmental study, and measured the concentrations of Co, Ni, Zn, As, Cu, and Pb in the roots, shoots, soil, and irrigating water. The plants irrigated with wastewater showed significant accumulation of heavy metals in the roots and some translocation of heavy metals from the roots to the shoots. We also performed an experiment with two 0.3 m3 pools to more closely study the feasibility of these plants for filtering water of contaminants, including mineral compounds, and altering its chemical characteristics. In our anatomical studies, the cells of the treatment roots showed irregularities and abnormal appearances in all tissue layers. The diameter and area of the xylem and the size of the cortical parenchyma have increased in the treatment plants of both species, confirmed by Stereolite software. Phytoremediation studies indicated that S. crassa accumulated As, Cu, Zn, Pb, Co, and Ni, and S. maritima accumulated As, Co, Zn, and Cu. S. crassa accumulated more heavy metals in its roots, whereas S. maritima accumulated more in its shoots. The biological oxygen demand and chemical oxygen demand were also significantly reduced in the wastewater passed through pools with S. crassa. Our results indicate that both genera are hyperaccumulators of heavy metals and therefore hold promise for industrial wastewater treatment, especially the absorption of As.

Studies on influence of process parameters on simultaneous biodegradation of atrazine and nutrients in aquatic environments by a membrane photobioreactor.

A Lab scale algal-bacterial membrane photobioreactor (MPBR) was designed and operated under 12-h light and 12-h dark conditions with a light intensity of 8000lx, in order to investigate the effects of initial concentrations of atrazine, carbon concentration, and hydraulic retention time on the ability of this photobioreactor in simultaneous removal of atrazine and nutrients in the continuous mode. The removal efficiencies of atrazine (ATZ), chemical oxygen demand (COD), phosphorus (PO43--P) and nitrogen (NOx) in optimum condition was more than 95%, 99%, 98% and 97% when the maximum removal rates were 9.5 × 10-3, 99.231, 11.773 and 7.762mg/L-day, respectively. Results showed that the quality of the effluent was reduced by the increase of atrazine concentration. The outcomes on the hydraulic and toxic shocks indicated that the system has a relatively good resistance to the shocks and can return to the stable conditions. Microalgae showed a great deal of interest and capability in cultivating and attaching to the surface of the membrane and bioreactor, and the total biomass accumulated in the system was greater than 6g/L. The kinetic coefficients of atrazine removal were also studied using various kinetic models. The maximum atrazine removal rate was determined by the modified Stover-Kincannon model. The results approved the ability of the MPBR reactor in wastewater treatment and microalgae cultivation and growth. The decline of atrazine concentration in this system could be attributed to the algal-bacterial symbiosis and co-metabolism process. Accordingly, the MPBR reactor is a practical, simple, economical and therefore suitable process for simultaneous biodegradation of chlorinated organic compounds and nutrients removal from aquatic environments.

Concentration and type of bioaerosols before and after conventional disinfection and sterilization procedures inside hospital operating rooms.

Operating rooms (ORs) in hospitals are sensitive wards because patients can get infections. This work aimed to characterize the type and concentration of bioaerosols in nine ORs of an educational hospital before and after sterilization and disinfection. During 2017, fungal samples were incubated at 25-28 °C for 3-7 days and bacterial samples at 37 °C for 24-48 h. The study results showed that the concentrations of fungi before cleaning procedures (for both of disinfection and sterilization) were limited from 4.83 to 18.40 CFU/m3 and after cleaning procedures ranged from 1.90 to 8.90 CFU/m3. In addition, the concentrations of bacteria before cleaning procedures were limited 14.65-167.40 CFU/m3 and after cleaning procedures ranged from 9.50 to 38.40 CFU/m3. The difference between the mean concentrations of airborne bioaerosols before and after sterilization was significantly different than the suggested value of 30 CFU/m3 (p ≤ 0.05). The bacterial concentration was higher than the recommended value (30 CFU/m3) in 41% of the ORs. The main fungal species identified in the indoor air of ORs (before vs. after sterilization) were A. fumigatus (25.6 vs. 18.3%), A. Niger (11.6 vs. 5.8%), Penicillium spp. (5.5 vs. 3.3%), Alternaria spp. (2.8 vs. 0.7%), Fusarium spp. (9.7 vs. 3.7%), Mucor spp. (15 vs. 12.7%), Cephalotrichum spp. (1.7 vs. 0.8%), A. Flavus (24.6 vs. 18.5%), Cladosporium spp. (2.6 vs. 0.8%), and Trichoderma spp. (0 vs. 0.9%). The growth of biological species even after sterilization and disinfection likely resulted from factors including poor ventilation, sweeping of OR floors, inadequate HVAC filtration, high humidity, and also lack of optimum management of infectious waste after surgery. Designing well-constructed ventilation and air-conditioning systems, replacing HEPA filters, implementing more stringent, frequent, and comprehensive disinfection procedures, and controlling temperature and humidity can help decrease bioaerosols in ORs.

Characteristics and health effects of BTEX in a hot spot for urban pollution.

This study reports a spatiotemporal characterization of toluene, benzene, ethylbenzene, and xylenes concentrations (BTEX) in an urban hot spot in Iran, specifically at an bus terminal region in Shiraz. Sampling was carried out according to NIOSH Compendium Method 1501. The inverse distance weighting (IDW) method was applied for spatial mapping. The Monte Carlo simulation technique was applied to evaluate carcinogenic and non-carcinogenic risk owing to BTEX exposure. The highest average BTEX concentrations were observed for benzene in the morning (at 7:00-9:00 A.M. local time) (26.15 ±â€¯17.65 µg/m3) and evening (at 6:00-8:00 P.M. local time) (34.44 ±â€¯15.63 µg/m3). The benzene to toluene ratios in the morning and evening were 2.02 and 3.07, respectively. The main sources of BTEX were gas stations and a municipal solid waste transfer station. The inhalation lifetime cancer risk (LTCR) for benzene in the morning and evening were 1.96 × 10-4 and 2.49 × 10-4, respectively, which exceeds the recommended value by US EPA and WHO. The hazard quotient (HQ) of all these pollutants was less than 1. The results of this work have implications for public health near 'hot spots' such as IKBT where large populations are exposed to carcinogenic emissions.

Evaluation of kenaf fibers as moving bed biofilm carriers in algal membrane photobioreactor.

In this lab-scale study, the feasibility of using kenaf fibers as moving bed biofilm carriers in hybrid microalgal membrane photobioreactors (HMPBR) in organic matter and atrazine elimination from real secondary effluent was evaluated. For evaluating the kinetics of biofilm substrate consumption, an experimental model was proposed. Inoculation of wastewater samples with free carriers resulted in the greater removal of target pollutants. Removal efficiency of atrazine and chemical oxygen demand (COD) increased to 27% and 16%, with respect to the control, respectively. The total biomass accumulation in HMPBR exceeded 5g/L, and the microalgae tended to aggregate and attached to biofilm carriers. The removal efficiency of HMPBR improved significantly via inoculation of kenaf fiber carriers with bioremediation microalgal strains (p < 0.01). A lower stabilization ratio (VSS/TSS) was also recorded. The biomass in HMPBR included more lipids and carbohydrates. The results revealed that kenaf fibers could improve and upgrade the biological activity of different wastewater treatment applications, considering the great potential of biofilm carriers and their effluent quality.

Biodegradation of atrazine from wastewater using moving bed biofilm reactor under nitrate-reducing conditions: A kinetic study.

In this study employed an anoxic moving bed biofilm reactor (AnMBBR) to evaluate the effects of hydraulic and toxic shocks on performance reactor. The results indicated a relatively good resistance of system against exercised shocks and its ability to return to steady-state conditions. In optimal conditions when there was the maximum rate of atrazine and soluble chemical oxygen demand (COD) removal were 74.82% and 99.29% respectively. Also, atrazine biodegradation rapidly declines in AnMBBR from 74% ±â€¯0.05 in the presence of nitrate to 9.12% only 3 days after the nitrate was eliding from the influent. Coefficients kinetics was studied and the maximum atrazine removal rate was determined by modified Stover & Kincannon model (Umax = 9.87 gATZ/m3d). Results showed that AnMBBR is feasible, easy, affordable, so suitable process for efficiently biodegrading toxic chlorinated organic compounds such as atrazine. Also, its removal mechanism in this system is co-metabolism.

Simultaneous removal of atrazine and organic matter from wastewater using anaerobic moving bed biofilm reactor: A performance analysis.

In this study, an anaerobic moving bed biofilm reactor (AMBBR) was designed to biodegrade atrazine under mesophilic (32 °C) condition and then it was evaluated for approximately 1 year. After biofilm formation, acclimation, and enrichment of microbial population within the bioreactor, the effect of various operation conditions such as changes in the concentration of influent atrazine and sucrose, hydraulic retention time (HRT), and salinity on the removal of atrazine and chemical oxygen demand (COD) were studied. In optimum conditions, the maximum removal efficiency of atrazine and COD was 60.5% and 97.4%, respectively. Various models were developed to predict the performance of atrazine removal as a function of HRT during continuous digestion. Also, coefficients kinetics was studied and the maximum atrazine removal rate was determined by Stover - Kincannon model (rmax = 0.223 kgATZ/m3d). Increasing salinity up to 20 g/L NaCl in influent flow could inhibit atrazine biodegradation process strongly in the AMBBR reactor; whereas, the reactor could tolerate the concentrations less than 20 g/L easily. Results showed that AMBBR is feasible, easy, affordable, so suitable process for efficiently biodegrading toxic chlorinated organic compounds such as atrazine. There was no accumulation of atrazine in the biofilm and the loss of atrazine in the control reactor was negligible; this shows that atrazine removal mechanism in this system was due to co-metabolism.

A new recycling technique for the waste tires reuse.

In this series of laboratory experiments, the feasibility of using fixed bed biofilm carriers (FBBC) manufactured from existing reclaimed waste tires (RWTs) for wastewater treatment was evaluated. To assess polyamide yarn waste tires as a media, the fixed bed sequence batch reactor (FBSBR) was evaluated under different organic loading rate (OLRs). An experimental model was used to study the kinetics of substrate consumption in biofilm. Removal efficiency of soluble chemical oxygen demand (SCOD) ranged by 76-98% for the FBSBR compared to 71-96% in a sequencing batch reactor (SBR). Removal efficiency of FBBC was significantly increased by inoculating these RWTs carriers. The results revealed that the sludge production yield (Yobs) was significantly less in the FBSBR compared to the SBR (p < 0.01). It also produced less sludge and recorded a lower stabilization ratio (VSS/TSS). The findings show that the Stover-Kincannon model was the best fit (R2 > 99%) in a FBSBR. Results from this study suggest that RWTs to support biological activity for a variety of wastewater treatment applications as a biofilm carrier have high potential that better performance as COD and TSS removal and sludge settling properties and effluent quality supported these findings.

Biological monitoring of urinary 1-hydroxypyrene by PAHs exposure among primary school students in Shiraz, Iran.

AIM OF STUDY: This research aimed to estimate PAHs exposure in primary school students and determine its association with other PAHs-related factors. MATERIALS AND METHODS: In total, 120 male primary school students (9-12 years old) were randomly selected from urban and suburban areas in Shiraz. The parents were required to complete a questionnaire including information about second-hand smoke exposure, residential traffic density, daily diet, and walking or being driven to school. High-performance liquid chromatography with fluorescence detector was also used to analyze urinary 1-OHP. t test, ANOVA (with Ducan's post hoc test), and multiple regression analysis were used to analyze the relationship between quantitative and qualitative variables and urinary 1-OHP concentration. RESULTS: The range and geometric mean of the creatinine-corrected 1-OHP levels were 120-6950 and 1460 ng/g creatinine, respectively. Besides, 1-OHP levels were higher among the children with smoker parents compared to those having non-smoker parents. The results also revealed a correlation between the duration of exposure to second-hand tobacco smoke and 1-OHP concentration. This correlation was also observed for daily uptake of smoked or grilled foods. However, traffic congestion did not have any significant effects on 1-OHP levels. PAHs are commonly present in Iranian diet. As a result, the weekly intake of dietary PAHs was the most effective predictor of PAHs exposure in the study population. CONCLUSION: Due to adverse health effects of PAHs on humans, especially children, more extensive studies are required to identify the sources that contribute to environmental PAHs exposure.

Green synthesis of sustainable magnetic nanoparticles Fe3O4 and Fe3O4-chitosan derived from Prosopis farcta biomass extract and their performance in the sorption of lead(II).

The sustainable processes are now in tremendous demand for nanomaterial synthesis as a result of their unique properties and characteristics. The magnetic nanoparticles comprised of Fe3O4 and its conjugate with abundant and renewable biopolymer, chitosan, were synthesized using Prosopis farcta biomass extract, and the resulting materials were used to adsorb Pb (II) from aqueous solution. Thermodynamic parameters revealed that the sorption of lead (II) on Fe3O4 as well as Fe3O4-Chitosan (Fe3O4-CS) has been an endothermic and self-regulating procedure wherein the sorption kinetics was defined by a pseudo-second-order pattern and the sorption isotherms corresponded to the Freundlich pattern. A multivariable quadratic technique for adsorption process optimization was implemented to optimize the lead (II) adsorption on Fe3O4 and Fe3O4-chitosan nanoparticles, the optimal conditions being pH 7.9, contact time of 31.2 min, initial lead concentration of 39.2 mg/L, adsorbent amount of 444.3 mg, at a 49.7 °C temperature. The maximum adsorption efficiencies under optimal conditions were found to be 69.02 and 89.54 % for Fe3O4 and Fe3O4-CS adsorbents, respectively. Notably, Fe3O4 and Fe3O4-CS can be easily recovered using an external magnet, indicating that they are a viable and cost-effective lead removal option.