RESUMEN
In the context of the Internet of Things, billions of devices-especially sensors-will be linked together in the next few years. A core component of wireless passive sensor nodes is the rectifier, which has to provide the circuit with sufficient operating voltage. In these devices, the rectifier has to be as energy efficient as possible in order to guarantee an optimal operation. Therefore, a numerical optimization scheme is proposed in this paper, which is able to find a unique optimal solution for an integrated Complementary Metal-Oxide-Semiconductor (CMOS) rectifier circuit with Self-Vth-Cancellation (SVC). An exploration of the parameter space is carried out in order to generate a meaningful target function for enhancing the rectified power for a fixed communication distance. In this paper, a mean conversion efficiency is introduced, which is a more valid target function for optimization than the Voltage Conversion Efficiency (VCE) and the commonly used Power Conversion Efficiency (PCE) and is defined as the arithmetic mean between PCE and VCE. Various trade-offs between output voltage, PCE, VCE and MCE are shown, which provide valuable information for low power rectifier designs. With the proposed method, a rectifier in a low power 55 nm process from Globalfoundries (GF55LPe) is optimized and simulated at -30 dBm input power. A mean PCE of 63.33% and a mean VCE of 63.40% is achieved.
RESUMEN
One of the biggest impacts of the vision 'Internet of Things' is the massive number of connected devices, where billions of nodes will exchange data, information and commands. While wireless systems offer advantages such as increased flexibility, they also introduce one major challenge: how to power each individual node. In many cases, there is no way around the use of batteries. To minimize the environmental impact, increasing the battery's longevity is the most important factor. This paper introduces a wireless battery-assisted node that has a drastically reduced energy consumption in the standby mode. The state (on/off) will be changed by harvesting a radiofrequency signal. A latching switch connects or disconnects the load-for example, a microcontroller-and the battery. The switch is connected to a charge pump which converts an AC (alternating current) signal into a usable DC (direct current) control signal. An antenna is mounted to the charge pump via a matching network. An electromagnetic wave is emitted by a remote control switch that switches the system on and off. The used frequency is 868 MHz and therefore in the UHF RFID (ultra high frequency radio frequency identification) band. The measurement results show that the wireless node consumes less than 16 nW in the standby mode. The remote controlling is possible from a distance of more than 12 m . The presented system can be integrated in further work on a UHF RFID tag. Thus, the existing protocol standard can be used to identify the object to be switched. By custom commands, the switching request can be transmitted from the remote control (UHF RFID reader) to the switching node.
RESUMEN
Ultra high frequency radio frequency identification (UHF RFID) is becoming a key technology in the Internet of Things. It allows the implementation of batteryless and wireless nodes, including sensors and actuators. Due to its possible transmission range of >10 m and potential to carry critical information, security is a highly important topic. For this reason, the International Organization for Standardization has published several crypto suites for UHF RFID within the ISO-29167 standard in 2014. Recently, research has focused on implementing those encryption features on the transponder side. However, currently no crypto enabled UHF RFID readers are available. In order to cope with the rapid development in this field, 'open' and flexible readers based on software defined radios are needed. They make it possible to quickly adapt the protocol and to test new functionalities such as encryption. This paper deals with the first implementation of the ISO 29167-19 standardized RAMON decryption on a software defined radio. The programming of this hardware is done in LabVIEW which allows for controlling the built-in transceiver modules. However, first measurements show that the decryption takes 51 s. This is because LabVIEW is not suitable for handling very large numbers like they are utilized in cryptography. Because such a long processing time is not feasible in experiments nor in a real-life scenarios, this method is not suitable for a prototyping platform. Thus, a different approach is chosen to optimize the decryption processing time. LabVIEW still provides the framework for handling the protocol and controlling the transceivers, but the decryption is performed in a Java application. In that way, the entire decryption process takes only about 2.2 ms, which is 23,318 times faster than the implementation in LabVIEW. Thus, this new approach meets the necessary timing requirements and is suitable for realistic application scenarios. The shown method allows development and testing of new functionalities in UHF RFID systems but may also be employed in any application that require long processing times in LabVIEW. Furthermore, the implementation of decryption features is the first necessary step towards a fully compliant, crypto enabled interrogator for UHF RFID, featuring a high adaptability.