Carbon nanowall-based gas sensors for carbon dioxide gas detection.

Carbon nanowalls (CNWs) have attracted significant attention for gas sensing applications due to their exceptional material properties such as large specific surface area, electric conductivity, nano- and/or micro-porous structure, and high charge carrier mobility. In this work, CNW films were synthesized and used to fabricate gas sensors for carbon dioxide (CO2) gas sensing. The CNW films were synthesized using an inductively-coupled plasma (ICP) plasma-enhanced chemical vapor deposition (PECVD) method and their structural and morphological properties were characterized using Raman spectroscopy and electron microscopy. The obtained CNW films were used to fabricate gas sensors employing interdigitated gold (Au) microelectrodes. The gas sensors were fabricated using both direct synthesis of CNW films on interdigitated Au microelectrodes on quartz and also transferring presynthesized CNW films onto interdigitated Au microelectrodes on glass. The CO2gas-sensing properties of fabricated devices were investigated for different concentrations of CO2gas and temperature-ranges. The sensitivities of fabricated devices were found to have a linear dependence on the concentration of CO2gas and increase with temperature. It was revealed that devices, in which CNW films have a maze-like structure, perform better compared to the ones that have a petal-like structure. A sensitivity value of 1.18% was obtained at 500 ppm CO2concentration and 100 °C device temperature. The CNW-based gas sensors have the potential for the development of easy-to-manufacture and efficient gas sensors for toxic gas monitoring.

Plasma with carbon nanoparticles: advances and application.

This article is devoted to the study of the glow intensity of radio-frequency capacitive discharge plasma with nanoparticles for further use in lighting devices. The process of carbon nanoparticles synthesis in the radiofrequency discharge was investigated, and the influence of plasma parameters on the formation and growth of the material was also studied. A method for determining the diameter of nanoparticles based on self-bias voltage and electron density is considered. It is revealed that the diameter of nanoparticles has a considerable influence on the optical properties of the plasma, in particular, on the emission intensity. Based on the obtained data, laboratory samples of lighting devices with improved luminous intensities were developed.

An Advanced Material with Synergistic Viscoelasticity Enhancement of Hydrophobically Associated Water-Soluble Polymer and Surfactant.

In order to prepare materials with controllable properties, changeable microstructure, and high viscoelasticity solution with low polymer and surfactant concentration, a composite is constituted by adding surfactant (sodium dodecyl sulfate, SDS) to hydrophobically associated water-soluble polymer (abbreviated as PAAC) solution. The viscoelasticity, aggregate microstructure, and interaction mechanism of the composite are investigated by rheometery, Cryo-transmission electron microscopy (Cryo-TEM), and fluorescence spectrum. The results show that when the mass ratio of polymer to surfactant is 15:1, the viscosity of the composite reaches the maximum. The viscosity of the composite system increases hundredfold. The viscosity plateau under dynamic shear is generated. The composite has the properties of high viscoelasticity, strong shear thinning behavior, and good salt tolerance, and temperature resistance. The maximum viscosity of the composite is shown at the salinity of 20000 mg L-1 . In addition, there is no phase separation in the composite with the increase of polymer and surfactant concentration, which indicates the good stability of the system. It is proposed a method to obtain a high viscoelasticity solution by adding surfactants without wormlike micelles to a hydrophobically associated water-soluble polymer solution.

Fabricating durable and stable superhydrophobic coatings by the atmospheric pressure plasma polymerisation of hexamethyldisiloxane.

The paper was devoted to the results of the study of methods to obtain superhydrophobic film based on the plasma polymerisation of hexamethyldisiloxane (HMDSO) inside the plasma jet at atmospheric pressure. The 3D printing technology was intended for film deposition, which has the advantage of producing superhydrophobic surfaces over a wide range of scales. The effect of synthesis parameters on the hydrophobic properties of the film has been studied. The obtained superhydrophobic films demonstrated stability and resistance in chemical solutions, at high temperatures, under the influence of UV-irradiation and in various weather conditions. The results can be used in various fields, including automotive, construction, electronics, medicine and others, where surface protection against moisture, contamination and corrosion is required.

Influence of fullerene content on the properties of polyurethane resins: A study of rheology and thermal characteristics.

The effect of different contents of fullerene on the properties of polyurethane resins (PUs), including rheology and thermal properties, was investigated. Polyurethane resins were prepared through polyaddition reactions using different isocyanate monomers such as isophorone diisocyanate (IPDI), methylene diphenyl diisocyanate (MDI), hexamethylene diisocyanate (HDI), and different polyols, such as poly(oxytetramethylene) glycol (PTMG), the triol trade name FA-703, and polypropylene glycols (PPG), at an NCO/OH ratio 0.94 and a temperature of 100 °C. IR spectroscopy was used to control the polymerization of PUs through the shifting of NCO peaks. The results showed that the rheology and thermal properties of the prepared PU resins depend on the type of isocyanates and fullerene used. Based on the type of isocyanates, the PU resin prepared by MDI has the highest viscosity and thermal stability compared to the other isocyanates investigated. On the other hand, the PU resins prepared by IPDI mixed with fullerene had the highest viscosity and thermal stability. However, the initial decomposition temperature (T onset) of the PUs decreased with the addition of fullerene without affecting the maximum decomposition temperature (PDT max) of the PU resin.

Synthesis and in situ oxidation of copper micro- and nanoparticles by arc discharge plasma in liquid.

This work presents a one-step controlled method for the synthesis of copper oxide nanoparticles using an arc discharge in deionized water without subsequent thermal annealing. The synthesis conditions were varied by changing the arc discharge current from 2 to 4 A. Scanning electron microscopy images of samples synthesized at discharge current of 2 A revealed the formation of tenorite (CuO) nanopetals with an average length of 550 nm and a width of 100 nm, which had a large surface area. Arc discharge synthesis at 3 and 4 A current modes provides the formation of a combination of CuO nanopetals with spherical cuprite (Cu2O) nanoparticles with sizes ranging from 30 to 80 nm. The crystalline phase and elemental composition of the synthesized particles were identified by X-ray diffraction analysis, Raman spectroscopy and Energy dispersive analysis. As the arc discharge current was raised from 2 to 4 A, two notable changes occurred in the synthesized particles: the Cu/O ratio increased, and the particle sizes decreased. At 4 A, the synthesized particles were from 30 to 80 nm in size and had a spherical shape, indicating an increase in the amount of cuprite (Cu2O) phase. The optical band gap of the aqueous solutions of copper oxide particles also increased from 2 to 2.34 eV with increasing synthesis current from 2 to 4 A, respectively. This suggests that the proposed synthesis method can be used to tune the band gap of the final material by controlling the Cu/O ratio through the current of arc discharge. Overall, this work demonstrates a novel approach to the synthesis of copper oxide nanoparticles with controllable CuO/Cu2O/Cu ratios, which has the potential to be useful in a variety of applications, particularly due to the significant enhancement of photocatalytic abilities and widen the working spectral range.

Efficient Recovery Annealing of the Pseudocapacitive Electrode with a High Loading of Cobalt Oxide Nanoparticles for Hybrid Supercapacitor Applications.

Electrochemical pseudocapacitors, along with batteries, are the essential components of today's highly efficient energy storage systems. Cobalt oxide is widely developing for hybrid supercapacitor pseudocapacitance electrode applications due to its wide range of redox reactions, high theoretical capacitance, low cost, and presence of electrical conductivity. In this work, a recovery annealing approach is proposed to modify the electrochemical properties of Co3O4 pseudocapacitive electrodes. Cyclic voltammetry measurements indicate a predominance of surface-controlled redox reactions as a result of recovery annealing. X-ray diffraction, Raman spectra, and XPES results showed that due to the small size of cobalt oxide particles, low-temperature recovery causes the transformation of the Co3O4 nanocrystalline phase into the CoO phase. For the same reason, a rapid reverse transformation of CoO into Co3O4 occurs during in situ oxidation. This recrystallization enhances the electrochemical activity of the surface of nanoparticles, where a high concentration of oxygen vacancies is observed in the resulting Co3O4 phase. Thus, a simple method of modifying nanocrystalline Co3O4 electrodes provides much-improved pseudocapacitance characteristics.

Effect of Electron and Proton Irradiation on Structural and Electronic Properties of Carbon Nanowalls.

In this work, a complex experimental study of the effect of electron and proton ionizing radiation on the properties of carbon nanowalls (CNWs) is carried out using various state-of-the-art materials characterization techniques. CNW layers on quartz substrates were exposed to 5 MeV electron and 1.8 MeV proton irradiation with accumulated fluences of 7 × 1013 e/cm2 and 1012 p/cm2, respectively. It is found that depending on the type of irradiation (electron or proton), the morphology and structural properties of CNWs change; in particular, the wall density decreases, and the sp2 hybridization component increases. The morphological and structural changes in turn lead to changes in the electronic, optical, and electrical characteristics of the material, in particular, change in the work function, improvement in optical transmission, an increase in the surface resistance, and a decrease in the specific conductivity of the CNW films. Lastly, this study highlights the potential of CNWs as nanostructured functional materials for novel high-performance radiation-resistant electronic and optoelectronic devices.

Stabilization of the Surface of ZnO Films and Elimination of the Aging Effect.

Zinc oxide is a promising multifunctional material. The practical use of nano- and polycrystalline ZnO devices faces a serious problem of instability of electrical and luminescent characteristics, due to the adsorption of oxygen by the surface during aging. In this paper, the aging effect in ZnO films and nanorod arrays was studied. It was found that ZnO samples demonstrate different behavior of the degradation process, which corresponds to at least two different types of adsorbing surface sites for O2, where O2 adsorption is of a different nature. The first type of surface sites is rapidly depassivated after hydrogen passivation and the aging effect takes place due to these centers. The second type of surface sites has a stable structure after hydrogen passivation and corresponds to HO-ZnO sites. The XPS components of these sites include the Zn2p3/2 peak at 1022.2 ± 0.2 eV and Zn2p1/2 peak at 1045.2 ± 0.2 eV, with a part of the XPS O1s peak at 531.5 ± 0.3 eV. The annealing transforms the first type of site into the second one, and the subsequent short-term plasma treatment in hydrogen results in steady passivation, where the degradation of characteristics is practically reduced to zero.

Physical properties of carbon nanowalls synthesized by the ICP-PECVD method vs. the growth time.

Investigation of the physical properties of carbon nanowall (CNW) films is carried out in correlation with the growth time. The structural, electronic, optical and electrical properties of CNW films are investigated using electron microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, UV-Vis spectroscopy, Hall Effect measurement system, Four Point Probing system, and thermoelectric measurements. Shorter growth time results in thinner CNW films with a densely spaced labyrinth structure, while a longer growth time results in thicker CNW films with a petal structure. These changes in morphology further lead to changes in the structural, optical, and electrical properties of the CNW.