Effect of Nanofiller Loading on Cure Efficiency and Potential Color Change of Model Composites.

OBJECTIVES: To evaluate the effect of nanofiller loading on cure efficiency and potential color change of experimental composites. MATERIALS AND METHODS: Four different polymeric materials were produced using the same organic matrix blend. To this matrix, different amounts of 0.05 µm fumed silica filler were added: no filler, 13, 52, and 65wt%. Fourier transform infrared spectroscopy was used to evaluate the degree of conversion (DC) for each composite using near-IR analysis, and spectrophotometry according to CIELab chromatic space was used to evaluate the color change.To induce color change, composites were artificially aged with exposure to cycles of UV-B light for 300 hours. Trasmission electron microscopy was used to illustrate nanoffiler aglomeration in the resin matrix. Data were analyzed using correlation analysis (α = 0.05). RESULTS: There was an excellent inverse linear correlation between filler wt% and either DC or color change. Greater changes to red (+Δa) and yellow (+Δb) were observed as the filler wt% increased. CONCLUSIONS: A higher percentage of nano-sized filler particles in dental resin composites directly affects their cure efficiency and potential for color change. CLINICAL SIGNIFICANCE: The increase in filler particle loading negatively affected monomer conversion and color stability of resin-based composites. As reduced filler loading results in poorer mechanical properties, to enhance color stability, resin-based composites should be formulated by making the refractive index of the polymeric matrix more closely match that of the filler throughout the polymerization process. (J Esthet Restor Dent, 2016).

A novel disposable self-adhesive inked paper device for electrochemical sensing of dopamine and serotonin neurotransmitters and biosensing of glucose.

In this work, we detail the progress of a novel electrochemical disposable device, which has a relatively low cost and easy production, with a novel conductive ink, that consists of graphite and automotive varnish mixture, deposited over a self-adhesive paper, granting an easy production with relatively low cost. The electrode surface was characterized by scanning electron microscopy, X-ray powder diffraction and Fourier transforms infrared and Raman, cyclic voltammetry and electrochemical impedance spectroscopies. In addition, the proposed electrode was applied for individual electrochemical determination of dopamine and serotonin. The device achieved a linear response between 30 and 800 µmol L-1 and a limit of detection (LOD) of 0.13 µmol L-1, by square wave voltammetry for dopamine and a linear range from 6.0 to 100 µmol L-1, with a LOD of 0.39 µmol L-1, by differential pulse voltammetry for serotonin. Later, the working electrode was modified with glucose oxidase and dihexadecyl phosphate film in order to obtain a biosensor. At this stage, CV was applied to detect glucose in the range of 1.0-10 µmol L-1 and LOD of 0.21 µmol L-1. By three different techniques and analytes, the sensoring and biosensoring processes presented high reproducibility. The proposed adhesive electrode is easy to prepare, disposable, within non-restrictive nature, which allows an approach of a new device for electrochemical sensing and biosensing.

Effect of different photoinitiators and reducing agents on cure efficiency and color stability of resin-based composites using different LED wavelengths.

OBJECTIVES: To evaluate the effect of photoinitiators and reducing agents on cure efficiency and color stability of resin-based composites using different LED wavelengths. METHODS: Model resin-based composites were associated with diphenyl(2,4,6-trimethylbenzoyl) phosphine oxide (TPO), phenylbis(2,4,6-trimethylbenzoyl) phosphine oxide (BAPO) or camphorquinone (CQ) associated with 2-(dimethylamino) ethyl methacrylate (DMAEMA), ethyl 4-(dimethyamino) benzoate (EDMAB) or 4-(N,N-dimethylamino) phenethyl alcohol (DMPOH). A narrow (Smartlite, Dentisply) and a broad spectrum (Bluephase G2, Ivoclar Vivadent) LEDs were used for photo-activation (20 J/cm(2)). Fourier transform infrared spectroscopy (FT-IR) was used to evaluate the cure efficiency for each composite, and CIELab parameters to evaluated color stability (ΔE00) after aging. The UV-vis absorption spectrophotometric analysis of each photoinitiator and reducing agent was determined. Data were analyzed using two-way ANOVA and Tukey's test for multiple comparisons (α=0.05). RESULTS: Higher cure efficiency was found for type-I photoinitiators photo-activated with a broad spectrum light, and for CQ-systems with a narrow band spectrum light, except when combined with an aliphatic amine (DMAEMA). Also, when combined with aromatic amines (EDMAB and DMPOH), similar cure efficiency with both wavelength LEDs was found. TPO had no cure efficiency when light-cured exclusively with a blue narrowband spectrum. CQ-systems presented higher color stability than type-I photoinitiators, especially when combined with DMPOH. CONCLUSIONS: After aging, CQ-based composites became more yellow and BAPO and TPO lighter and less yellow. However, CQ-systems presented higher color stability than type-I photoinitiators, as BAPO- and TPO-, despite their higher cure efficiency when photo-activated with corresponding wavelength range. CLINICAL SIGNIFICANCE: Color matching is initially important, but color change over time will be one of the major reasons for replacing esthetic restorations; despite the less yellowing of these alternative photoinitiators, camphorquinone presented higher color stability.

Cytotoxicity and degree of conversion of methacrylate and silorane

Composites have been proven to have a cytotoxic effect on a variety of tissues and cells. Aim: The aim of this study was to analyse the degree of conversion of resins and its correlation with the cell viability in primary gingival fibroblasts. Methods: Resin-based silorane (Filtek P90) and conventional methacrylate resins (Filtek Z100, Filtek Z250 and Filtek Z350XT) were used to evaluate cell viability and the degree of conversion. The resins were light-cured by a LED for 20 and 40 seconds. The degree of conversion was analysed by Fourier transform infrared spectroscopy. Cellular metabolism was evaluated after 24 hours by the MTT assay (n = 6) using the storage solution of composite resin for either 24 hours or 12 days. Variance analysis (ANOVA) with a Bonferroni correction (p < 0.05) was performed to compare the groups. Results: The composite Filtek P90 showed a higher degree of conversion when polymerised for 40 or 20 seconds, while the composites Filtek Z100, Filtek Z250 and Filtek Z350XT showed similar degree of conversion. Only the Filtek Z100 resin was cytotoxic. Conclusion: We found no statistically significant correlation between cell viability and the degree of conversion

Influence of Different Photoinitiators on Polymerization Kinetics and Marginal Microleakage in Restorations using Photopolymerizable Dental Composites

Objective: To evaluate the influence of four different photoinitiators on the polymerization kinetics and marginal microleakage in class V restorations using photopolymerizable dental composites. Material and Methods: Four photopolymerizable dental composites based on Bis-GMA (14.5 wt %), UDMA (6.5 wt %) and silanized filler particles (79 wt %) containing different photoinitiators were formulated. Camphorquinone (CQ)/amine, phenyl-propanedione (PPD), monoacylphosphine oxide (Lucirin® TPO) and bisacylphosphine oxide (Irgacure® 819) were used as photoinitiators. Sixteen intact human third molars were selected and divided into four groups. All teeth received class V cavity preparations in their buccal and lingual surfaces and were submitted to a dye leakage test. Data were independently analyzed for both enamel and dentin, and the results were assessed by a Kruskal-Walis test. The polymerization reactions of the four composites were evaluated by differential scanning calorimeter coupled with photocalorimeter accessory. Results: Lucirin® TPO presented the highest scores for microleakage in enamel, whereas the other photoinitiators have not demonstrated statistical differences. The lowest scores were obtained for PPD in dentin while the highest scores have been achieved by Irgacure® 819 and Lucirin® TPO. Photocalorimetric measurements demonstrated a correlation between polymerization reaction rate and marginal leakage, showing that faster reactions cause greater marginal leakage. Conclusion: Marginal microleakage scores in photopolymerizable dental composites can be greatly influenced by different types of photoinitiators through their distinct reaction rates.