Multi-Functional Electrospun AgNO3/PVB and Its Ag NP/PVB Nanofiber Membrane.

This study focuses on the fabrication of fiber membranes containing different concentrations of AgNO3 via the electrospinning technique. The AgNO3 present in the fibers is subsequently reduced to silver nanoparticles (Ag NPs) through UV irradiation. The resulting nanofiber film is characterized using scanning electron microscopy, X-ray diffraction, and evaluations of its anti-UV and anti-electromagnetic radiation properties. Experimental results demonstrate that increasing the AgNO3 content initially decreases and then increases the fiber diameter and fiber diameter deviation. Under UV light, the nanofibers fuse and bond, leading to an increase in the fiber diameter. AgNO3 is effectively reduced to Ag NPs after UV irradiation for more than 60 min, as confirmed by the characteristic diffraction peaks of Ag NPs in the XRD spectrum of the irradiated AgNO3/PVB fibers. The nanofiber film containing AgNO3 exhibits superior anti-UV performance compared to the film containing AgNO3-derived Ag NPs. The anti-electromagnetic radiation performances of the nanofiber films containing AgNO3 and AgNO3-derived Ag NPs are similar, but the nanofiber film containing AgNO3-derived Ag NPs exhibits higher performance at approximately 2.5 GHZ frequency. Additionally, at an AgNO3 concentration of less than 0.5 wt%, the anti-electromagnetic radiation performance is poor, and the shielding effect of the nanofiber film on medium- and low-frequency electromagnetic waves surpasses that on high-frequency waves. This study provides guidance for the preparation of polyvinyl butyral nanofibers, Ag NPs, and functional materials with anti-ultraviolet and anti-electromagnetic radiation properties.

3D Poly (L-lactic acid) fibrous sponge with interconnected porous structure for bone tissue scaffold.

Large bone defects, often resulting from trauma and disease, present significant clinical challenges. Electrospun fibrous scaffolds closely resembling the morphology and structure of natural ECM are highly interested in bone tissue engineering. However, the traditional electrospun fibrous scaffold has some limitations, including lacking interconnected macropores and behaving as a 2D scaffold. To address these challenges, a sponge-like electrospun poly(L-lactic acid) (PLLA)/polycaprolactone (PCL) fibrous scaffold has been developed by an innovative and convenient method (i.e., electrospinning, homogenization, progen leaching and shaping). The resulting scaffold exhibited a highly porous structure (overall porosity = 85.9 %) with interconnected, regular macropores, mimicking the natural extracellular matrix. Moreover, the incorporation of bioactive glass (BG) particles improved the hydrophilicity (water contact angle = 79.7°) and biocompatibility and promoted osteoblast cell growth. In-vitro 10-day experiment revealed that the scaffolds led to high cell viability. The increment of the proliferation rates was 195.4 % at day 7 and 281.6 % at day 10. More importantly, Saos-2 cells could grow, proliferate, and infiltrate into the scaffold. Therefore, this 3D PLLA/PCL with BG sponge holds great promise for bone defect repair in tissue engineering applications.

Stimuli-Responsive Codelivery System-Embedded Polymeric Nanofibers with Synergistic Effects of Growth Factors and Low-Intensity Pulsed Ultrasound to Enhance Osteogenesis Properties.

The present work aims to develop optimized scaffolds for bone repair by incorporating mesoporous nanoparticles into them, thereby combining bioactive factors for cell growth and preventing rapid release or loss of effectiveness. We synthesized biocompatible and biodegradable scaffolds designed for the controlled codelivery of curcumin (CUR) and recombinant human bone morphogenic protein-2 (rhBMP-2). Active agents in dendritic silica/titania mesoporous nanoparticles (DSTNs) were incorporated at different weight percentages (0, 2, 5, 7, 9, and 10 wt %) into a matrix of polycaprolactone (PCL) and polyethylene glycol (PEG) nanofibers, forming the CUR-BMP-2@DSTNs/PCL-PEG delivery system (S0, S2, S5, S7, S9, and S10, respectively, with the number showing the weight percentage). To enhance the formation process, the system was treated using low-intensity pulsed ultrasound (LIPUS). Different advanced methods were employed to assess the physical, chemical, and mechanical characteristics of the fabricated scaffolds, all confirming that incorporating the nanoparticles improves their mechanical and structural properties. Their hydrophilicity increased by approximately 25%, leading to ca. 53% enhancement in their water absorption capacity. Furthermore, we observed a sustained release of approximately 97% for CUR and 70% for BMP-2 for the S7 (scaffold with 7 wt % DSTNs) over 28 days, which was further enhanced using ultrasound. In vitro studies demonstrated accelerated scaffold biodegradation, with the highest level observed in S7 scaffolds, approximately three times higher than the control group. Moreover, the cell viability and proliferation on DSTNs-containing scaffolds increased when compared to the control group. Overall, our study presents a promising nanocomposite scaffold design with notable improvements in structural, mechanical, and biological properties compared to the control group, along with controlled and sustained drug release capabilities. This makes the scaffold a compelling candidate for advanced bone tissue engineering and regenerative therapies.

A Biodegradable Stereo-Complexed Poly (Lactic Acid) Drinking Straw of High Heat Resistance and Performance.

Current biodegradable drinking straws suffer from poor heat resistance and rigidity when wet, causing user dissatisfaction. Here, a fully biodegradable straw formed by stereocomplexation of poly (lactic acid) (SC-PLA) is reported. Because of the unique strong interaction and high density of link chains between stereocomplex crystallites (over 70% crystallinity), SC-PLA straws outperform their counterparts on the market. This coupled with the advantages of simple processing (solution casting and annealing) and relatively low cost (~2.06 cents per straw) makes SC-PLA drinking straws a superior substitute for plastic ones. Commercially available PLLA straws lose almost 60% of their flexural strength when wet compared to less than 5% of the SC-PLA straws proposed in this study.

Heterogeneous porous PLLA/PCL fibrous scaffold for bone tissue regeneration.

Bone tissue engineering has become one of the most promising therapeutic methods to treat bone defects. A suitable scaffolding material to regenerate new bone tissues should have a high specific surface area, high porosity and a suitable surface structure which benefit cell attachment, proliferation, and differentiation. In this study, an acetone post-treatment strategy was developed to generate heterogeneous structure. After PLLA/PCL nanofibrous membranes were electrospun and collected, they were treated with acetone to generate a highly porous structure. Meanwhile, part of PCL was extracted from the fibre and enriched on the fibre surface. The cell affinity of the nanofibrous membrane was verified by human osteoblast-like cells assay. The proliferation rate of heterogeneous samples increased 190.4 %, 265.5 % and 137.9 % at day 10 compared with pristine samples. These results demonstrated that the heterogeneous PLLA/PCL nanofibrous membranes could enhance osteoblast adhesion and proliferation. With high surface area (average surface area 36.302 m2/g) and good mechanical properties (average Young's modulus 1.65 GPa and average tensile strength 5.1 MPa), the heterogeneous PLLA/PCL membrane should have potential applications in the field of bone regeneration.

Tensile Strength and Dispersibility of Pulp/Danufil Wet-Laid Hydroentangled Nonwovens.

Wet-laid hydroentangled nonwovens are widely used for disposable products, but these products generally do not have good dispersibility and can block sewage systems after being discarded into toilets. In this study, both pulp fibers and Danufil fibers are selected as we hypothesize that the high wet strength and striated surface of Danufil fibers would allow us to produce nonwovens with better dispersibility while having enough mechanical properties. The wet strength and dispersibility of nonwovens are systematically studied by investigating the influence of the fiber blend ratio, fiber length, and water jet pressure. The results indicate that the percent dispersion could be as high as 81.3% when the wet strength is higher than 4.8 N, which has been improved greatly comparing the percent dispersion of 67.6% reported before.

EcoFlex Sponge with Ultrahigh Oil Absorption Capacity.

A paraffin microsphere-templated 3D porous EcoFlex sponge was prepared to selectively absorb oil or chemicals from water. The technology for producing this EcoFlex sponge does not need complicated synthesis processes or instruments, and the materials applied in this work are ecofriendly. Therefore, this sponge can be employed in the environmental field. EcoFlex sponges showed high hydrophobicity (contact angle = 140-143°) and oleophilicity. The developed sponge exhibits a porous three-dimensional framework inside with excellent internal connectivity, which contributes both better absorption capacity and faster absorption rate. For instance, the absorption capacity for chloroform can reach 3400 wt %. The absorption capacity of the sponge was optimized using different size of paraffin microspheres and these sponges exhibit relatively high absorption capacity in a short time (2 min). The volume of sponge expands in some oils and organic solvents: the increased volume capacity for hexane can reach 2200%. This sponge also has great recovery capability and durability; it keeps its original shape and absorption capacity after 15 cycles of oil absorption and compression.

Hierarchical Porous Poly(l-lactic acid) Nanofibrous Membrane for Ultrafine Particulate Aerosol Filtration.

Ultrafine particulate aerosols less than 100 nm diffuse randomly in the air and are hazardous to the environment and human health. However, no technical standards or commercial products are available for filtering particle sizes under 100 nm yet. Here, we report the development of a porous poly(l-lactic acid) (PLLA) nanofibrous membrane filter with an ultra-high specific surface area via electrospinning and a post-treatment process. After PLLA fibres were electrospun and collected, they were treated by acetone to generate a blossoming porous structure throughout each individual fibre. Characterizations of morphology, crystallinity, and mechanical and thermal properties demonstrated that the porous structure can be attributed to the nonsolvent-induced spinodal phase separation during electrospinning and solvent-induced recrystallization during post treatment. The blossoming porous structure with high specific surface area contributed to excellent filtration efficiency (99.99%) for sodium chloride (NaCl) ultrafine aerosol particles (30-100 nm) with a low pressure drop (110-230 Pa). Notably, under 7.8 cm/s air flow rate, the membrane samples performed better for filtering smaller-sized aerosol particles than the larger ones when evaluated by the quality factor (0.07). Finally, this finding demonstrates that the electrospun membrane with a hierarchical pore structure and high specific surface area hold great potential in applications as air-filtering materials.