RESUMEN
The geometric aberration of centered refracting double-plane symmetric optical systems (DPSOS) is investigated. For DPSOS with different defocus values in the tangential plane and the sagittal plane (astigmatic wavefront), a pair of curved reference surfaces which vanishes the quadratic terms of the optical path difference (OPD) between a general ray and a reference ray are deduced. With the curved reference surfaces, the primary (fourth-order) wave aberration function for DPSOS is calculated and analyzed, which can be used for beam shaping designs with astigmatic input wavefront, such as slab lasers and semiconductor lasers. Further, the proposed curved reference surfaces can be applied to analyze the aberrations of general DPSOS.
RESUMEN
An integrated aberration-compensating module (IACM), consisting mainly of an adjustable slab-aberration compensator, a one-dimensional Shack-Hartmann wavefront sensor, and a data processor, which meet the urgent requirements of correcting the specific wavefront aberrations of a slab laser based on an off-axis stable-unstable resonator, is designed and experimentally demonstrated. Benefits include compactness, robustness, simplicity, automation, and cost-effectiveness. The particular wavefront aberrations of the 9 kW level quasi-continuous-wave Nd:YAG slab laser, which have characteristics of asymmetry, large amplitude and gradient, high spatial frequency, and low temporal frequency, were measured and theoretically analyzed. In the experiment, the wavefront aberrations of the slab laser were corrected by the IACM. At the average output power of 9 kW, the diffraction-limited factor ß was improved from 20.3 times diffraction limit (DL) to 3.6 times DL. The peak-to-valley and root-mean-square values of aberrations were reduced from 9.6 to 0.85 µm and from 2.86 to 0.18 µm within five iterations of the IACM, respectively. Moreover, The IACM is capable of maintaining the compensating surface figure after power-off.
RESUMEN
We present a kilowatt-level quasi-continuous-wave (QCW) cryogenically cooled 946-nm slab laser oscillator for the first time, to the best of our knowledge. The laser system is based on a double-face-pumped large-size single-slab Nd:YAG design, delivering a record-high average power of 1.06 kW without additional amplification. This laser oscillator operates at repetition rate of 400 Hz with a pulse duration of 175 µs, resulting in a single pulse energy of 2.65 J. To the best of our knowledge, these results represent the highest output power and pulse energy for any all-solid-state 946-nm laser ever reported to date. Our scheme paves a new path for the development of the compact high-power solid-state 946-nm laser.
RESUMEN
For reshaping aperture size and correcting low-order aberration of laser beams with large aspect ratios, a simplified analytical method is proposed to design an anamorphic refractive shaping system, which is composed of double-plane symmetric lenses. The simplified method enables performing a global study of aberrations via calculating the analytical primary wave aberration function under paraxial approximation. The aberration balance is analyzed with a three-lens laser collimating system and a compact four-lens laser expanding system. Lens bending and conic surfaces are introduced to decrease ray errors. Through the simplified analytical method, anamorphic refractive shaping systems for laser beams with large aspect ratios can be adequately analyzed and conveniently designed.
RESUMEN
A void-free bonding technique was demonstrated for a large slab Nd: YAG crystal with a bonding surface dimension of â¼160mm×70mm. By using the novel fluxless oxide layer removal technology, the indium-oxide barrier problem was resolved. With the help of electrochemical-polished indium solder and a plasma-cleaned heat sink, the solderability of the indium was enhanced; in particular, the contact angle of the solder was improved from 51° to 31°. With the largest-bonding-size slab, a single-slab laser created a maximum output power of 7.3 kW under an absorbed pump power of 12.8 kW, corresponding to an optical to optical efficiency of 57% and a slope conversion of 67.8%. By detecting the wavefront of the interferometer before and after bonding, the RMS of wavefront was 0.192λ and 0.434λ (λ=633nm), respectively. To the best of our knowledge, this is the largest void-free bonding size for a laser slab and the highest output power achieved from a single-slab crystal laser oscillator.
RESUMEN
An 8 kW level quasi-continuous-wave (QCW) face-pumped 1064 nm slab laser with high beam quality was developed by a master oscillator power amplifier (MOPA) system. A single-mode fiber seed laser was amplified by two-stage single-pass Nd:YAG rod preamplifiers and four face-pumped Nd:YAG slab amplifiers. The slab amplifiers were well designed with uniform pumping and uniform cooling for well-distributed thermal and stress. A dynamically feedbacked optical aberration compensation device was employed to correct low-order optical aberration, and the residue high-order optical aberration was corrected by an adaptive optics system. The QCW MOPA delivered up to an average power of 8.2 kW with a pulse duration of 200 µs at a repetition rate of 400 Hz. The beam quality factor was measured to be ß=3.5.
RESUMEN
Continuous wave 808 nm pump laser-induced thermal damage of polycrystalline transparent ceramic and crystalline Nd:YAG materials was investigated both experimentally and theoretically. The measured temperature agrees well with the theoretical simulation, and the maximum hoop stresses occur on the incident facet of the end-pumped rod at about â2 times of the pump beam radius w0, where the temperature gradient is the highest and the damage occurs first at this location. The fracture-limited laser intensity of ceramics was experimentally measured to be 6.4±0.6 kW/cm2, nearly 64% higher than that of the crystals (3.9±0.3 kW/cm2). The deduced thermal fracture stress for ceramic was 386±50 MPa, which is 64% higher than that of the crystals (235±16 MPa).
RESUMEN
We present a compact high-efficiency and high-average-power diode-side-pumped Nd:YAG rod laser oscillator operated with a linearly polarized fundamental mode. The oscillator resonator is based on an L-shaped convex-convex cavity with an improved module and a dual-rod configuration for birefringence compensation. Under a pump power of 344 W, a linearly polarized average output power of 101.4 W at 1064 nm is obtained, which corresponds to an optical-to-optical conversion efficiency of 29.4%. The laser is operated at a repetition rate of 400 Hz with a beam quality factor of M(2)=1.14. To the best of our knowledge, this is the highest optical-to-optical efficiency for a side-pumped TEM(00) Nd:YAG rod laser oscillator with a 100-W-level output ever reported.