RESUMEN
A technique to improve the accuracy of complete arch implant intraoral digital scans and the accuracy of their virtual casts is described. Obtaining accurate complete arch implant intraoral digital scans with an intraoral scanner is challenging because of the smooth and movable tissues of edentulous areas. The described technique uses auxiliary clips attached to intraoral scan bodies to cover interimplant edentulous spans with immobile tooth-like geometric references that are more favorable for intraoral scanning. The technique is designed to be user friendly and compatible with any intraoral scanner.
RESUMEN
A technique to improve the accuracy of complete arch implant intraoral digital scans and to obtain more accurate virtual casts with them is described. First, 2 complete arch intraoral digital scans were obtained with an intraoral scanner: a multiunit abutment digital scan and an implant digital scan with reusable horizontal intraoral scan bodies (ISBs) placed on the implants. These were previously created by combining the conventional ISBs compatible with the patient's implants with extensional structures with occlusal geometry. Once the digital scans had been acquired, the position of the implants was obtained by superimposing a virtual design of the conventional ISB onto each horizontal ISB of the complete arch implant digital scan. Finally, the virtual cast was obtained by superimposing the complete arch multiunit abutment digital scan on the complete arch implant digital scan.
RESUMEN
A technique to obtain more accurate complete arch implant digital scans and virtual casts is described. In order to obtain complete arch implant digital scans with greater accuracy, short-span intraoral digital scans are superimposed with the aid of a geometric pattern. Therefore, the technique takes advantage of the accuracy of intraoral scanners to obtain digital scans of reduced spans. Two virtual designs of the geometric pattern have been made available online: one for maxillary arches and one for mandibular arches. From these virtual designs, new virtual designs of geometric patterns of different sizes and shapes can be created to better fit different arch forms and implant positions.
RESUMEN
A technique to improve the precision of recordings acquired with the 2 main digital occlusal analyzers on the market (T-Scan and OccluSense) is presented. This technique consists of using digital occlusal analyzers with a customizable centering tray. The virtual design of the centering tray is available online, together with that of the adapters required for both digital occlusal analyzers. The designs can be downloaded and additively manufactured for clinical use. These parts improve the positioning of the piezoelectric film sensors of the digital occlusal analyzers in the patient's mouth and thus the precision of their records. Improving the precision of the records of the digital occlusal analyzers is especially important for the comparison of records obtained at different stages of rehabilitation treatment.
RESUMEN
STATEMENT OF PROBLEM: Although different digital occlusal analyzers have been marketed, comparative studies are lacking. PURPOSE: The purpose of this in vitro study was to compare the repeatability and reproducibility of 2 different digital occlusal analyzers (T-Scan and OccluSense) for measuring the right- and left-side balance of occlusal contact forces. MATERIAL AND METHODS: The repeatability and reproducibility of the 2 digital occlusal analyzers for measuring the balance of occlusal contact forces were determined and compared by using the Gauge Repeatability and Reproducibility tests based on the International Organization for Standardization (ISO), ISO 5725-2 and ISO 5725-3 standards. Ten different dental casts were mounted in the maximum intercuspation position on a semi-adjustable articulator. Then, the balance of occlusal contact forces in each of the 10 articulated dental casts was measured 24 times with each of the 2 digital occlusal analyzers. In addition, as the OccluSense, unlike the T-Scan, does not have a centering support for the piezoelectric film sensor, measurements with it were performed without and with a custom-designed and manufactured centering support. Finally, the repeatability and reproducibility of both digital occlusal analyzers were determined and compared using the Gauge Repeatability and Reproducibility tests. RESULTS: The repeatability and reproducibility tests revealed that only 0.8% of the variance of the measurements obtained with the T-Scan was due to repeatability and reproducibility (0.4% repeatability, 0.4% reproducibility). In contrast, 12% of the variance of the measurements obtained with the OccluSense was due to repeatability and reproducibility (2.2% repeatability, 9.8% reproducibility). However, when using OccluSense with the centering support, the variance decreased to 6.4% (2.8% repeatability, 3.6% reproducibility). According to the Automotive Industry Action Group classification, the repeatability and reproducibility of the T-Scan were good, those of the OccluSense poor, and those of the OccluSense with the centering support medium. CONCLUSIONS: The repeatability and reproducibility of the T-Scan were significantly better than those of the OccluSense for measuring the balance of occlusal contact forces. Furthermore, the repeatability and reproducibility of the OccluSense were significantly improved when used with a device to center the piezoelectric film sensor between the incisors. Nevertheless, the repeatability and reproducibility of the T-Scan were better.
RESUMEN
STATEMENT OF PROBLEM: Digital occlusal analyzers allow the recording of dental contact forces. Some authors assume a unique location for the center of contact forces at the position of maximum intercuspation, while others indicate variations in dental contact forces when recorded at different times of the day. Which approach is more appropriate is unclear. PURPOSE: The purpose of this in vitro study was to analyze whether a change in the balance of masticatory forces influences the location of the center of contact forces and its magnitude. MATERIAL AND METHODS: Three different dental casts, selected under dental criteria, were mounted in maximum intercuspation on a semiadjustable articulator equipped with a pattern indicating 9 different force application points (intersection point between 3 longitudinal rows and 3 transverse columns). A force of constant magnitude (169 N) was applied 10 times at each of the application points, and occlusal forces were recorded with a digital occlusal analyzer. Then, two variables were studied: the location of the center of contact forces and its magnitude. Each force application position (9 positions × 3 dental casts=27 in total) was repeated 10 times, and measured data were statistically analyzed with 2-way repeated measures ANOVA (α=.05) test. RESULTS: The repeatability of the method indicated that the coefficient of variation mean was 0.37% in the location of the center of contact forces and that its magnitude was 3.70%. The 2-way repeated measures ANOVA test revealed statistically significant variations in the location of the center of contact forces and its magnitude, revealing that longitudinal changes of the application point of masticatory forces affected the magnitude of contact forces and that longitudinal and transverse changes of the application point of masticatory forces affected the location of the center of contact forces. CONCLUSIONS: The location of the center of contact force and its magnitude provided by a digital occlusal analyzer at the position of maximum intercuspation are not necessarily unique to each articulated dental cast. Even if the intensity of the masticatory force remains unchanged, changes in its lateral or longitudinal balance also influence the result of the occlusion forces.
Asunto(s)
Fuerza de la Mordida , Oclusión Dental , Articuladores DentalesRESUMEN
A technique for creating 3-dimensional virtual patients (3DVPs) by superimposing intraoral and facial digital scans guided with a novel aligner system is described. This aligner system supports design modifications to adapt to different facial scanning methods (FSMs) and reduce the impact of FSMs on the accuracy of 3DVPs. Two different designs of the aligner system are described: one for use with less-accurate FSMs and another for use with more-accurate FSMs. These virtual designs are available for download and use.