Investigation of the protective suitability of a dental fluorinated varnish by means of X Ray fluorescence and Raman spectroscopy.

BACKGROUND AND AIM: Evaluating the protective effect in human enamel of a fluorinated varnish after enduring a citric acid erosive challenge. METHODS: An in vitro model was developed considering the intraoral environment, human saliva and acid erosive procedures. The evaluation of the enamel specimens was undertaken through the direct analysis of enamel by means of Raman spectroscopy and Energy Dispersive X Ray Fluorescence (EDXRF). Ten tooth specimens per group were analysed during three stages: 1- before treatment; 2- After varnish (treatment group) or toothpaste (control) application; 3- After citric acid cycle. Additionally, Particle Induced Gamma Ray emission (PIGE) was used to gauge the fluorine uptake by enamel after the application of the varnish (stage 2). Results were presented as mean and standard deviation with ANOVA and Tukey post hoc performed considering a significance level of 0.05. RESULTS: A significant (p < 0.05) higher Ca levels were detected in treatment group at stage 2 (37.4 ± 0.4 w/w%) and 3 (37.1 ± 0.1) when compared to the control group. After varnish application in treatment group, depolarization ratios were significant lower (p < 0.05) and anisotropy were significant higher (p < 0.05), however no differences were detected in FWHM. CONCLUSIONS: The use of a fluorinated dental varnish suggests a protective effect for human enamel against dental erosion demineralization process which was detectable in an in vitro model.

Evaluation of the effect of fluorinated tooth bleaching products using polarized Raman microscopy and particle induced gamma-ray emission.

In this in vitro study, the effect of the application of tooth bleaching products in human enamel was evaluated using polarized Raman microscopy, particle induced gamma-ray emission (PIGE) and Vickers Hardness test. Due to their acidic nature, teeth whitening products are associated with changes in enamel mineralization. Consequently, products have appeared in the market that promote the incorporation of fluorine in order to decrease the solubility of the hydroxyapatite in enamel and prevent demineralization. This way, four commercial products with different active principle concentrations: 16% carbamide peroxide (Opalescence PF® and VivaStyle®) or 6% hydrogen peroxide (Opalescence Go PF® and VivaStyle Paint On®) and presence or not of fluorine were compared. The information on the crystalline state of the enamel was provided by the determination of the depolarization ratio of the symmetric stretching band of phosphate (at 959 cm-1). Furthermore, the content and uptake of F was evaluated using PIGE in the two fluorinated products as well as in one negative control group. In order to evaluate the microhardness of enamel by means of Vickers test, another group of polished samples was prepared (using Opalescence PF®) and evaluated. Conversely to what could be expected, the obtained results determined a statistically significant decrease of depolarization ratio, leading to an increase of mineralization after the application of the bleaching products, except for VivaStyle®. For this group, no significant variation was obtained before-after treatment, most likely due to the acidity of the product (pH = 5.8). Additionally, an increase of concentration of F in the dental tissues was determined for the fluorinated products. On the other hand, enamel polishing, required for the application of the Vickers test, led to increased susceptibility to erosion, resulting in decreased hardness and an increased enamel depolarization ratio.

Dosimetric effect by shallow air cavities in high energy electron beams.

This study evaluates the dosimetric impact caused by an air cavity located at 2 mm depth from the top surface in a PMMA phantom irradiated by electron beams produced by a Siemens Primus linear accelerator. A systematic evaluation of the effect related to the cavity area and thickness as well as to the electron beam energy was performed by using Monte Carlo simulations (EGSnrc code), Pencil Beam algorithm and Gafchromic EBT2 films. A home-PMMA phantom with the same geometry as the simulated one was specifically constructed for the measurements. Our results indicate that the presence of the cavity causes an increase (up to 70%) of the dose maximum value as well as a shift forward of the position of the depth-dose curve, compared to the homogeneous one. Pronounced dose discontinuities in the regions close to the lateral cavity edges are observed. The shape and magnitude of these discontinuities change with the dimension of the cavity. It is also found that the cavity effect is more pronounced (6%) for the 12 MeV electron beam and the presence of cavities with large thickness and small area introduces more significant variations (up to 70%) on the depth-dose curves. Overall, the Gafchromic EBT2 film measurements were found in agreement within 3% with Monte Carlo calculations and predict well the fine details of the dosimetric change near the cavity interface. The Pencil Beam calculations underestimate the dose up to 40% compared to Monte Carlo simulations; in particular for the largest cavity thickness (2.8 cm).

The use of non-standard CT conversion ramps for Monte Carlo verification of 6 MV prostate IMRT plans.

Monte Carlo (MC) dose calculation algorithms have been widely used to verify the accuracy of intensity-modulated radiotherapy (IMRT) dose distributions computed by conventional algorithms due to the ability to precisely account for the effects of tissue inhomogeneities and multileaf collimator characteristics. Both algorithms present, however, a particular difference in terms of dose calculation and report. Whereas dose from conventional methods is traditionally computed and reported as the water-equivalent dose (Dw), MC dose algorithms calculate and report dose to medium (Dm). In order to compare consistently both methods, the conversion of MC Dm into Dw is therefore necessary. This study aims to assess the effect of applying the conversion of MC-based Dm distributions to Dw for prostate IMRT plans generated for 6 MV photon beams. MC phantoms were created from the patient CT images using three different ramps to convert CT numbers into material and mass density: a conventional four material ramp (CTCREATE) and two simplified CT conversion ramps: (1) air and water with variable densities and (2) air and water with unit density. MC simulations were performed using the BEAMnrc code for the treatment head simulation and the DOSXYZnrc code for the patient dose calculation. The conversion of Dm to Dw by scaling with the stopping power ratios of water to medium was also performed in a post-MC calculation process. The comparison of MC dose distributions calculated in conventional and simplified (water with variable densities) phantoms showed that the effect of material composition on dose-volume histograms (DVH) was less than 1% for soft tissue and about 2.5% near and inside bone structures. The effect of material density on DVH was less than 1% for all tissues through the comparison of MC distributions performed in the two simplified phantoms considering water. Additionally, MC dose distributions were compared with the predictions from an Eclipse treatment planning system (TPS), which employed a pencil beam convolution (PBC) algorithm with Modified Batho Power Law heterogeneity correction. Eclipse PBC and MC calculations (conventional and simplified phantoms) agreed well (<1%) for soft tissues. For femoral heads, differences up to 3% were observed between the DVH for Eclipse PBC and MC calculated in conventional phantoms. The use of the CT conversion ramp of water with variable densities for MC simulations showed no dose discrepancies (0.5%) with the PBC algorithm. Moreover, converting Dm to Dw using mass stopping power ratios resulted in a significant shift (up to 6%) in the DVH for the femoral heads compared to the Eclipse PBC one. Our results show that, for prostate IMRT plans delivered with 6 MV photon beams, no conversion of MC dose from medium to water using stopping power ratio is needed. In contrast, MC dose calculations using water with variable density may be a simple way to solve the problem found using the dose conversion method based on the stopping power ratio.