A Na-Free Surface Enables "Three-In-One" Enhancement of Structural, Interfacial and Air Stability for Sodium-Ion Battery Cathodes.

O3-type layered oxides are regarded as one of the most promising cathode materials for sodium-ion batteries. However, the multistep phase transitions, severe electrode/electrolyte parasitic reactions, and moisture sensitivity are challenging for their practical application because of the highly active Na+. Here, a Na-free layer is built on the surface of NaNi1/3Mn1/3Fe1/3O2 (NMF111) via a leaching treatment and the subsequent surface reconstruction. Accordingly, both the structural degradation from bulk to surface and the overgrowth of the solid electrolyte interface (SEI) are greatly ameliorated, which results in the improved capacity retention of modified NMF111 from 58.3% to 89.6% after 400 cycles at 1 C. Besides, the Na-free surface with rock-salt structure prevents the H+/Na+ exchange and then enables good reversibility and low polarization of the optimal NMF111 when exposed to wet air (50% RH) for 4 days. This work opens a new avenue for the comprehensive cyclability improvement of layered oxides via surface reconstruction.

In Situ Fast Construction of Ni3S4/FeS Catalysts on 3D Foam Structure Achieving Stable Large-Current-Density Water Oxidation.

By increasing the content of Ni3+, the catalytic activity of nickel-based catalysts for the oxygen evolution reaction (OER), which is still problematic with current synthesis routes, can be increased. Herein, a Ni3+-rich of Ni3S4/FeS on FeNi Foam (Ni3S4/FeS@FNF) via anodic electrodeposition to direct obtain high valence metal ions for OER catalyst is presented. XPS showed that the introduction of Fe not only further increased the Ni3+ concentration in Ni3S4/FeS to 95.02%, but also inhibited the dissolution of NiOOH by up to seven times. Furthermore, the OER kinetics is enhanced by the combination of the inner Ni3S4/FeS heterostructures and the electrochemically induced surface layers of oxides/hydroxides. Ni3S4/FeS@FNF shows the most excellent OER activity with a low Tafel slope of 11.2 mV dec-1 and overpotentials of 196 and 445 mV at current densities of 10 and 1400 mA cm-2, respectively. Furthermore, the Ni3S4/FeS@FNF catalyst can be operated stably at 1500 mA cm-2 for 200 h without significant performance degradation. In conclusion, this work has significantly increased the high activity Ni3+ content in nickel-based OER electrocatalysts through an anodic electrodeposition strategy. The preparation process is time-saving and mature, which is expected to be applied in large-scale industrialization.

An Active Strategy to Reduce Residual Alkali for High-Performance Layered Oxide Cathode Materials of Sodium-Ion Batteries.

Residual alkali is one of the biggest challenges for the commercialization of sodium-based layered transition metal oxide cathode materials since it can even inevitably appear during the production process. Herein, taking O3-type Na0.9Ni0.25Mn0.4Fe0.2Mg0.1Ti0.05O2 as an example, an active strategy is proposed to reduce residual alkali by slowing the cooling rate, which can be achieved in one-step preparation method. It is suggested that slow cooling can significantly enhance the internal uniformity of the material, facilitating the reintegration of Na+ into the bulk material during the calcination cooling phase, therefore substantially reducing residual alkali. The strategy can remarkably suppress the slurry gelation and gas evolution and enhance the structural stability. Compared to naturally cooled cathode materials, the capacity retention of the slowly cooled electrode material increases from 76.2% to 85.7% after 300 cycles at 1 C. This work offers a versatile approach to the development of advanced cathode materials toward practical applications.

Se-p Orbitals Induced "Strong d-d Orbitals Interaction" Enable High Reversibility of Se-Rich ZnSe/MnSe@C Electrode as Excellent Host for Sodium-Ion Storage.

The heterostructure of transition-metal chalcogenides is a promising approach to boost alkali ion storage due to fast charge kinetics and reduction of activation energy. However, cycling performance is a paramount challenge that is suffering from poor reversibility. Herein, it is reported that Se-rich particles can chemically interact with local hexagonal ZnSe/MnSe@C heterostructure environment, leading to effective ions insertion/extraction, enabling high reversibility. Enlightened by theoretical understanding, Se-rich particles endow high intrinsic conductivities in term of low energy barriers (1.32 eV) compared with those without Se-rich particles (1.50 eV) toward the sodiation process. Moreover, p orbitals of Se-rich particles may actively participate and further increase the electronegativity that pushes the Mn d orbitals (dxy and dx2-y2) and donate their electrons to dxz and dyz orbitals, manifesting strong d-d orbitals interaction between ZnSe and MnSe. Such fundamental interaction will adopt a well-stable conducive electronic bridge, eventually, charges are easily transferred from ZnSe to MnSe in the heterostructure during sodiation/desodiation. Therefore, the optimized Se-rich ZnSe/MnSe@C electrode delivered high capacity of 576 mAh g-1 at 0.1 A g-1 after 100 cycles and 384 mAh g-1 at 1 A g-1 after 2500 cycles, respectively. In situ and ex situ measurements further indicate the integrity and reversibility of the electrode materials upon charging/discharging.

Cu-N Synergism Regulation to Enhance Anionic Redox Reversibility and Activity of Li- and Mn-Rich Layered Oxides Cathode.

Anionic redox chemistry enables extraordinary capacity for Li- and Mn-rich layered oxides (LMROs) cathodes. Unfortunately, irreversible surface oxygen evolution evokes the pernicious phase transition, structural deterioration, and severe electrode-electrolyte interface side reaction with element dissolution, resulting in fast capacity and voltage fading of LMROs during cycling and hindering its commercialization. Herein, a redox couple strategy is proposed by utilizing copper phthalocyanine (CuPc) to address the irreversibility of anionic redox. The Cu-N synergistic effect of CuPc could not only inhibit surface oxygen evolution by reducing the peroxide ion O2 2- back to lattice oxygen O2-, but also enhance the reaction activity and reversibility of anionic redox in bulk to achieve a higher capacity and cycling stability. Moreover, the CuPc strategy suppresses the interface side reaction and induces the forming of a uniform and robust LiF-rich cathode electrolyte, interphase (CEI) to significantly eliminate transition metal dissolution. As a result, the CuPc-enhanced LMRO cathode shows superb cycling performance with a capacity retention of 95.0% after 500 long-term cycles. This study sheds light on the great effect of N-based redox couple to regulate anionic redox behavior and promote the development of high energy density and high stability LMROs cathode.

Achieving High Initial Coulombic Efficiency and Capacity in a Surface Chemical Grafting Layer of Plateau-type Sodium Titanate.

The plateau-type sodium titanate with suitable sodiation potential is a promising anode candidate for high safe and high energy density of sodium-ion batteries (SIBs). However, the poor initial Coulombic efficiency (ICE) and cyclic instability of sodium titanate are attributed to the unstable interfacial structure along with the decomposition of electrolytes, resulting in the continuous formation of solid electrolyte interface (SEI) film. To address this issue, a chemical grafting method is developed to fabricate a highly stable interface layer of inert Al2O3 on the sodium titanate anode, rendering the high ICE and excellent cycling stability. Based on theoretical calculations, NaPF6 are more likely adsorption on the Al2O3 surface and produce sodium fluoride. The formation of a thin and dense SEI film with rich sodium fluoride achieves the low interfacial resistances and charge-transfer resistances. Benefitting from our design, the obtained sodium titanate exhibits a high ICE from 67.7 % to 79.4 % and an enhanced reversible capacity from 151 mAh g-1 to 181 mAh g-1 at 20 mA g-1, along with an increase in capacity retention from 56.5 % to 80.6 % after 500 cycles. This work heralds a promising paradigm for rational regulation of interfacial stability to achieve high-performance anodes for SIBs.

Tuning the Solvation Structure in Water-Based Solution Enables Surface Reconstruction of Layered Oxide Cathodes toward Long Lifespan Sodium-Ion Batteries.

Layered oxides of sodium-ion batteries suffer from severe side reactions on the electrode/electrolyte interface, leading to fast capacity degradation. Although surface reconstruction strategies are widely used to solve the above issues, the utilization of the low-cost wet chemical method is extremely challenging for moisture-sensitive Na-based oxide materials. Here, the solvation tuning strategy is proposed to overcome the deterioration of NaNi1/3Mn1/3Fe1/3O2 in water-based solution and conduct the surface reconstruction. When capturing the water molecules by the solvation structure of cations, here is Li+, the structural collapse and degradation of layered oxides in water-based solvents are greatly mitigated. Furthermore, Li(H2O)3EA+ promotes the profitable Li+/Na+ exchange to build a robust surface, which hampers the decomposition of electrolytes and the structural evolution upon cycling. Accordingly, the lifespan of Li-reinforced materials is prolonged to three times that of the pristine one. This work represents a step forward in understanding the surface reconstruction operated in a water-based solution for high-performance sodium layered oxide cathodes.

Ordered planar plating/stripping enables deep cycling zinc metal batteries.

Metal anodes are emerging as culminating solutions for the development of energy-dense batteries in either aprotic, aqueous, or solid battery configurations. However, unlike traditional intercalation electrodes, the low utilization of "hostless" metal anodes due to the intrinsically disordered plating/stripping impedes their practical applications. Herein, we report ordered planar plating/stripping in a bulk zinc (Zn) anode to achieve an extremely high depth of discharge exceeding 90% with negligible thickness fluctuation and long-term stable cycling. The Zn can be plated/stripped with (0001)Zn preferential orientation throughout the consecutive charge/discharge process, assisted by a self-assembled supramolecular bilayer at the Zn anode-electrolyte interface. Through real-time tracking of the Zn atoms migration, we reveal that the ordered planar plating/stripping is driven by the construction of in-plane Zn─N bindings and the gradient energy landscape at the reaction fronts. The breakthrough results provide alternative insights into the ordered plating/stripping of metal anodes toward rechargeable energy-dense batteries.

Polymeric Electronic Shielding Layer Enabling Superior Dendrite Suppression for All-Solid-State Lithium Batteries.

LiBH4 is one of the most promising candidates for use in all-solid-state lithium batteries. However, the main challenges of LiBH4 are the poor Li-ion conductivity at room temperature, excessive dendrite formation, and the narrow voltage window, which hamper practical application. Herein, we fabricate a flexible polymeric electronic shielding layer on the particle surfaces of LiBH4. The electronic conductivity of the primary LiBH4 is reduced by 2 orders of magnitude, to 1.15 × 10-9 S cm-1 at 25 °C, due to the high electron affinity of the electronic shielding layer; this localizes the electrons around the BH4- anions, which eliminates electronic leakage from the anionic framework and leads to a 68-fold higher critical electrical bias for dendrite growth on the particle surfaces. Contrary to the previously reported work, the shielding layer also ensures fast Li-ion conduction due to the fast-rotational dynamics of the BH4- species and the high Li-ion (carrier) concentration on the particle surfaces. In addition, the flexibility of the layer guarantees its structural integrity during Li plating and stripping. Therefore, our LiBH4-based solid-state electrolyte exhibits a high critical current density (11.43 mA cm-2) and long cycling stability of 5000 h (5.70 mA cm-2) at 25 °C. More importantly, the electrolyte had a wide operational temperature window (-30-150 °C). We believe that our findings provide a perspective with which to avoid dendrite formation in hydride solid-state electrolytes and provide high-performance all-solid-state lithium batteries.