Higher sea surface temperature in the Indian Ocean during the Last Interglacial weakened the South Asian monsoon.

SignificanceUnderstanding the drivers of South Asian monsoon intensity is pivotal for improving climate forecasting under global warming scenarios. Solar insolation is assumed to be the dominant driver of monsoon variability in warm climate regimes, but this has not been verified by proxy data. We report a South Asian monsoon rainfall record spanning the last ∼130 kyr in the Ganges-Brahmaputra-Meghna river catchment. Our multiproxy data reveal that the South Asian monsoon was weaker during the Last Interglacial (130 to 115 ka)-despite higher insolation-than during the Holocene (11.6 ka to present), thus questioning the widely accepted model assumption. Our work implies that Indian Ocean warming may increase the occurrence of severe monsoon failures in South Asia.

Sol-Gel-Derived Ordered Mesoporous High Entropy Spinel Ferrites and Assessment of Their Photoelectrochemical and Electrocatalytic Water Splitting Performance.

The novel material class of high entropy oxides with their unique and unexpected physicochemical properties is a candidate for energy applications. Herein, it is reported for the first time about the physico- and (photo-) electrochemical properties of ordered mesoporous (CoNiCuZnMg)Fe2 O4 thin films synthesized by a soft-templating and dip-coating approach. The A-site high entropy ferrites (HEF) are composed of periodically ordered mesopores building a highly accessible inorganic nanoarchitecture with large specific surface areas. The mesoporous spinel HEF thin films are found to be phase-pure and crack-free on the meso- and macroscale. The formation of the spinel structure hosting six distinct cations is verified by X-ray-based characterization techniques. Photoelectron spectroscopy gives insight into the chemical state of the implemented transition metals supporting the structural characterization data. Applied as photoanode for photoelectrochemical water splitting, the HEFs are photostable over several hours but show only low photoconductivity owing to fast surface recombination, as evidenced by intensity-modulated photocurrent spectroscopy. When applied as oxygen evolution reaction electrocatalyst, the HEF thin films possess overpotentials of 420 mV at 10 mA cm-2 in 1 m KOH. The results imply that the increase of the compositional disorder enhances the electronic transport properties, which are beneficial for both energy applications.

Mesoporous CuFe2 O4 Photoanodes for Solar Water Oxidation: Impact of Surface Morphology on the Photoelectrochemical Properties.

Metal oxide-based photoelectrodes for solar water splitting often utilize nanostructures to increase the solid-liquid interface area. This reduces charge transport distances and increases the photocurrent for materials with short minority charge carrier diffusion lengths. While the merits of nanostructuring are well established, the effect of surface order on the photocurrent and carrier recombination has not yet received much attention in the literature. To evaluate the impact of pore ordering on the photoelectrochemical properties, mesoporous CuFe2 O4 (CFO) thin film photoanodes were prepared by dip-coating and soft-templating. Here, the pore order and geometry can be controlled by addition of copolymer surfactants poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic® F-127), polyisobutylene-block-poly(ethylene oxide) (PIB-PEO) and poly(ethylene-co-butylene)-block-poly(ethylene oxide) (Kraton liquid™-PEO, KLE). The non-ordered CFO showed the highest photocurrent density of 0.2 mA/cm2 at 1.3 V vs. RHE for sulfite oxidation, but the least photocurrent density for water oxidation. Conversely, the ordered CFO presented the best photoelectrochemical water oxidation performance. These differences can be understood on the basis of the high surface area, which promotes hole transfer to sulfite (a fast hole acceptor), but retards oxidation of water (a slow hole acceptor) due to electron-hole recombination at the defective surface. This interpretation is confirmed by intensity-modulated photocurrent (IMPS) and vibrating Kelvin probe surface photovoltage spectroscopy (VKP-SPS). The lowest surface recombination rate was observed for the ordered KLE-based mesoporous CFO, which retains spherical pore shapes at the surface resulting in fewer surface defects. Overall, this work shows that the photoelectrochemical energy conversion efficiency of copper ferrite thin films is not just controlled by the surface area, but also by surface order.

On the structural evolution of nanoporous optically transparent CuO photocathodes upon calcination for photoelectrochemical applications.

Copper oxides are promising photocathode materials for solar hydrogen production due to their narrow optical band gap energy allowing broad visible light absorption. However, they suffer from severe photocorrosion upon illumination, mainly due to copper reduction. Nanostructuring has been proven to enhance the photoresponse of CuO photocathodes; however, there is a lack of precise structural control on the nanoscale upon sol-gel synthesis and calcination for achieving optically transparent CuO thin film photoabsorbers. In this study, nanoporous and nanocrystalline CuO networks were prepared by a soft-templating and dip-coating method utilizing poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic® F-127) as a structure-directing agent, resulting for the first-time in uniformly structured, crack-free, and optically transparent CuO thin films. The photoelectrochemical properties of the nanoporous CuO frameworks were investigated as a function of the calcination temperature and film thickness, revealing important information about the photocurrent, photostability, and photovoltage. Based on surface photovoltage spectroscopy (SPV), the films are p-type and generate up to 60 mV photovoltage at 2.0 eV (0.050 mW cm-2) irradiation for the film annealed at 750 °C. For these high annealing temperatures, the nanocrystalline domains in the thin film structure are more developed, resulting in improved electronic quality. In aqueous electrolytes with or without methyl viologen (as a fast electron acceptor), CuO films show cathodic photocurrents of up to -2.4 mA cm-2 at 0.32 V vs. RHE (air mass (AM) 1.5). However, the photocurrents were found to be entirely due to photocorrosion of the films and decay to near zero over the course of 20 min under AM 1.5 illumination. These fundamental results on the structural and morphological development upon calcination provide a direction and show the necessity for further (surface) treatment of sol-gel derived CuO photocathodes for photoelectrochemical applications. The study demonstrates how to control the size of nanopores starting from mesopore formation at 400 °C to the evolution of macroporous frameworks at 750 °C.

Rational Design of Mesoporous CuO-CeO2 Catalysts for NH3-SCR Applications Guided by Multiple In Situ Spectroscopies.

Efficient nontoxic catalysts for low-temperature NH3 selective catalytic reduction (NH3-SCR) applications are of great interest. Owing to their promising redox and low-temperature activity, we prepared CuO-CeO2 catalysts on a mesoporous SBA-15 support using targeted solid-state impregnation (SSI), guided by multiple in situ spectroscopy. The use of template P123 allowed dedicated modification of the surface properties of the SBA-15 matrix, resulting in a changed reactivity behavior of the metal precursors during the calcination process. To unravel the details of the transformation of the precursors to the final catalyst material, we applied in situ diffuse reflectance infrared Fourier transform (DRIFT), UV-visible (UV-vis), and Raman spectroscopies as well as online Fourier transform infrared (FTIR) monitoring of the gas-phase composition, in addition to ex situ surface, porosity, and structural analysis. The in situ analysis reveals two types of nitrate decomposition mechanisms: a nitrate-bridging route leading to the formation of a CuO-CeO2 solid solution with increased low-temperature NH3-SCR activity, and a hydrolysis route, which facilitates the formation of binary oxides CuO + CeO2 showing activity over a broader temperature window peaking at higher temperatures. Our findings demonstrate that a detailed understanding of catalytic performance requires a profound knowledge of the calcination step and that the use of in situ analysis facilitates the rational design of catalytic properties.

4-(Dimethylamino)pyridine as a powerful auxiliary reagent in the electroless synthesis of gold nanotubes.

Gold nanotubes of small particle sizes down to 5 nm and high aspect ratios were synthesized in ion track etched polycarbonate following a rational reaction design. 4-(Dimethylamino)pyridine (DMAP) was employed to adjust the electroless deposition by interfering with the autocatalytically active gold surface. Modification of the pH value and DMAP concentration led to a wide range of products which were characterized by SEM, TEM, and EDS. Filigree nanotubes of 10-15 nm wall thickness and 5.0 ± 2.1 nm grain size were obtained as well as robust and free-standing structures proving homogeneous deposition along the whole template length of 30 µm. Template-supported gold nanotubes were applied in the UV-vis monitored reduction of 4-nitrophenol by sodium borohydride under pseudo-first-order conditions. They proved to be a reliable microfluidic system of excellent catalytic activity coming up with an apparent rate constant of 1.3 × 10(-2) s(-1). Despite a high flow rate, the reaction showed 99% conversion after a distance of just 60 µm.

Ligand-optimized electroless synthesis of silver nanotubes and their activity in the reduction of 4-nitrophenol.

A facile electroless plating procedure for the controlled synthesis of nanoscale silver thin films and derived structures such as silver nanotubes was developed and the products were characterized by SEM, TEM and EDS. The highly stable plating baths consist of AgNO(3) as the metal source, a suitable ligand and tartrate as an environmentally benign reducing agent. Next to the variation of the coordinative environment of the oxidizing component, the influence of the pH value was evaluated. These two governing factors strongly affect the plating rate and the morphology of the developing silver nanoparticle films and can be used to adapt the reaction to synthetic demands. The refined electroless deposition allows the fabrication of homogeneous high aspect-ratio nanotubes in ion track etched polycarbonate. Template-embedded metal nanotubes can be interpreted as parallelled microreactors. Following this concept, both the silver nanotubes and spongy gold nanotubes obtained by the use of the silver structures as sacrificial templates were applied in the reduction of 4-nitrophenol by sodium borohydride, proving to be extraordinarily effective catalysts.

Structure and Thermodynamics of Silicon Oxycarbide Polymer-Derived Ceramics with and without Mixed-Bonding.

Silicon oxycarbides synthesized through a conventional polymeric route show characteristic nanodomains that consist of sp2 hybridized carbon, tetrahedrally coordinated SiO4, and tetrahedrally coordinated silicon with carbon substitution for oxygen, called "mixed bonds." Here we synthesize two preceramic polymers possessing both phenyl substituents as unique organic groups. In one precursor, the phenyl group is directly bonded to silicon, resulting in a SiOC polymer-derived ceramic (PDC) with mixed bonding. In the other precursor, the phenyl group is bonded to the silicon through Si-O-C bridges, which results in a SiOC PDC without mixed bonding. Radial breathing-like mode bands in the Raman spectra reveal that SiOC PDCs contain carbon nanoscrolls with spiral-like rolled-up geometry and open edges at the ends of their structure. Calorimetric measurements of the heat of dissolution in a molten salt solvent show that the SiOC PDCs with mixed bonding have negative enthalpies of formation with respect to crystalline components (silicon carbide, cristobalite, and graphite) and are more thermodynamically stable than those without. The heats of formation from crystalline SiO2, SiC, and C of SiOC PDCs without mixed bonding are close to zero and depend on the pyrolysis temperature. Solid state MAS NMR confirms the presence or absence of mixed bonding and further shows that, without mixed bonding, terminal hydroxyls are bound to some of the Si-O tetrahedra. This study indicates that mixed bonding, along with additional factors, such as the presence of terminal hydroxyl groups, contributes to the thermodynamic stability of SiOC PDCs.

Pressure-induced decomposition of indium hydroxide.

A static pressure-induced decomposition of indium hydroxide into metallic indium that takes place at ambient temperature is reported. The lattice parameter of c-In(OH)(3) decreased upon compression from 7.977(2) to approximately 7.45 A at 34 GPa, corresponding to a decrease in specific volume of approximately 18%. Fitting the second-order Birch-Murnaghan equation of state to the obtained compression data gave a bulk modulus of 99 +/- 3 GPa for c-In(OH)(3). The c-In(OH)(3) crystals with a size of approximately 100 nm are comminuted upon compression, as indicated by the grain-size reduction reflected in broadening of the diffraction reflections and the appearance of smaller (approximately 5 nm) incoherently oriented domains in TEM. The rapid decompression of compressed c-In(OH)(3) leads to partial decomposition of indium hydroxide into metallic indium, mainly as a result of localized stress gradients caused by relaxation of the highly disordered indium sublattice in indium hydroxide. This partial decomposition of indium hydroxide into metallic indium is irreversible, as confirmed by angle-dispersive X-ray diffraction, transmission electron microscopy imaging, Raman scattering, and FTIR spectroscopy. Recovered c-In(OH)(3) samples become completely black and nontransparent and show typical features of metals, i.e., a falling absorption in the 100-250 cm(-1) region accompanied by a featureless spectrum in the 250-2500 cm(-1) region in the Raman spectrum and Drude-like absorption of free electrons in the region of 4000-8000 cm(-1) in the FTIR spectrum. These features were not observed in the initial c-In(OH)(3), which is a typical white wide-band-gap semiconductor.

Novel 0D-nanocarbon-silica ceramic composites: sol-gel synthesis and high-temperature evolution.

Herein we report the synthesis of novel 0D-nanocarbon-based silicon-containing ceramic composites by a facile salt-free synthesis method followed by polymer-to-ceramic transformation. 0D-nanocarbon-silica composites were synthesized via a one-pot sol-gel process using tetramethyl orthosilicate (TMOS) and functionalized nanodiamonds and converted subsequently via pyrolysis under an argon atmosphere into nanodiamond/silica nanocomposites. The thermal conversion of the nanodiamond phase to a multilayer fullerene phase was carefully investigated by integral and local characterization methods such as vibrational spectroscopy, X-ray diffraction, BET, SEM and HRTEM. The incorporation of nanodiamonds in a silica matrix enhances the crystallization temperature of the silica phase, as α-cristobalite, to 1500 °C, while their full graphitization is shifted to T > 1700 °C under an argon atmosphere. The thermal decomposition of the nanodiamond/silica composites leads to the formation of materials with a high specific surface area (up to 562 m2 g-1) and a mesoporous structure. No carbothermal reaction of composing phases was identified. The results obtained in the present study allow for designing advanced and highly-defined mesoporous 0D-nanocarbon-containing composites with tailored structural features and multifunctional property profiles.

Synthesis of Silver Modified Bioactive Glassy Materials with Antibacterial Properties via Facile and Low-Temperature Route.

There is an increasing clinical need to develop novel biomaterials that combine regenerative and biocidal properties. In this work, we present the preparation of silver/silica-based glassy bioactive (ABG) compositions via a facile, fast (20 h), and low temperature (80 °C) approach and their characterization. The fabrication process included the synthesis of the bioactive glass (BG) particles followed by the surface modification of the bioactive glass with silver nanoparticles. The microstructural features of ABG samples before and after exposure to simulated body fluid (SBF), as well as their ion release behavior during SBF test were evaluated using infrared spectrometry (FTIR), ultraviolet-visible (UV-Vis) spectroscopy, X-ray diffraction (XRD), electron microscopies (TEM and SEM) and optical emission spectroscopy (OES). The antibacterial properties of the experimental compositions were tested against Escherichia coli (E. coli). The results indicated that the prepared ABG materials possess antibacterial activity against E. coli, which is directly correlated with the glass surface modification.

Response of Gallium Nitride Chemiresistors to Carbon Monoxide is Due to Oxygen Contamination.

We report on the influence of oxygen impurities on the gas sensing properties of gallium nitride (GaN) chemiresistors. As shown by XRD, elemental analysis, and TEM characterization, surface oxidation of GaN-for example, upon contact to ambient air atmosphere-creates an oxidative amorphous layer which provides the sites for the sensing toward CO. Treating this powder under dry ammonia at 800 °C converts the oxide layer in nitride, and consequently the sensing performance toward CO is dramatically reduced for ammonia treated GaN gas sensors. Hence the response of GaN sensors to CO is caused by oxygen in the form of amorphous surface oxide or oxynitride.

Elucidating the Origin of Hydrogen Evolution Reaction Activity in Mono- and Bimetallic Metal- and Nitrogen-Doped Carbon Catalysts (Me-N-C).

In this work, we present a comprehensive study on the role of metal species in MOF-based Me-N-C (mono- and bimetallic) catalysts for the hydrogen evolution reaction (HER). The catalysts are investigated with respect to HER activity and stability in alkaline electrolyte. On the basis of the structural analysis by X-ray diffraction, X-ray-induced photoelectron spectroscopy, and transmission electron microscopy, it is concluded that MeN4 sites seem to dominate the HER activity of these catalysts. There is a strong relation between the amount of MeN4 sites that are formed and the energy of formation related to these sites integrated at the edge of a graphene layer, as obtained from density functional theory (DFT) calculations. Our results show, for the first time, that the combination of two metals (Co and Mo) in a bimetallic (Co,Mo)-N-C catalyst allows hydrogen production with a significantly improved overpotential in comparison to its monometallic counterparts and other Me-N-C catalysts. By the combination of experimental results with DFT calculations, we show that the origin of the enhanced performance of our (Co,Mo)-N-C catalyst seems to be provided by an improved hydrogen binding energy on one MeN4 site because of the presence of a second MeN4 site in its close vicinity, as investigated in detail for our most active (Co,Mo)-N-C catalyst. The outstanding stability and good activity make especially the bimetallic Me-N-C catalysts interesting candidates for solar fuel applications.

Synthesis of nanoparticle/ligand composite thin films by sequential ligand self assembly and surface complex reduction.

Nanocomposite thin films consisting of ligand-connected metal nanoparticles were deposited by iteration of ligand assembly, surface complex formation and reduction. This novel and convenient approach combines characteristics of the layer-by-layer (LbL) and the successive ion layer adsorption and reaction (SILAR) techniques. In contrast to classical LbL assembly, the nanoparticle formation is performed in situ, avoiding separate reduction, protection and attachment steps. To demonstrate the versatility of the approach, different metal precursors (Pd, Ag and Au salts) and linkers (1,2-ethanedithiol, 1,4-benzenedithiol and polythiol) were applied. The formation of dithiol-linked nanoparticle films was confirmed by TEM and XPS. By combining the deposition protocol with ion track etched polycarbonate templates, nanotubes and nanowires with high aspect ratios of up to 300 could be fabricated.