RESUMEN
Our society largely relies on inorganic semiconductor devices which are, so far, fabricated using expensive and complex processes requiring ultra-high vacuum equipment. Here we report on the possibility of growing a p-n junction taking advantage of electrochemical processes based on the use of aqueous solutions. The growth of the junction has been carried out using the Electrochemical Atomic Layer Deposition (E-ALD) technique, which allowed to sequentially deposit two different semiconductors, CdS and Cu2S, on an Ag(111) substrate, in a single procedure. The growth process was monitored inâ situ by Surface X-Ray Diffraction (SXRD) and resulted in the fabrication of a thin double-layer structure with a high degree of crystallographic order and a well-defined interface. The high-performance electrical characteristics of the device were analysed ex-situ and show the characteristic feature of a diode.
RESUMEN
The ethanol electro-oxidation catalyzed by Pd in an alkaline environment involves several intermediate reaction steps promoted by the hydroxyl radical, OH. In this work, we report on the dynamical paths of the first step of this oxidation reaction, namely the hydrogen atom abstraction CH3CH2OH + OH â CH3CHOH + H2O, occurring at the Pd(111) surface and address the thermodynamic stability of the adsorbed reactants by means of quantum and molecular mechanics calculations, with special focus on the effect of the solvent. We have found that the impact of the solvent is significant for both ethanol and OH, contributing to a decrease in their adsorption free energies by a few dozen kcal mol-1 with respect to the adsorption energy under vacuum. Furthermore, we observe that hydrogen atom abstraction is enhanced for those simulation paths featuring large surface-reactant distances, namely, when the reactants weakly interact with the catalyst. The picture emerging from our study is therefore that of a catalyst whose coverage in an aqueous environment is largely dominated by OH with respect to ethanol. Nevertheless, only a small amount of them, specifically those weakly bound to the catalyst, is really active in the ethanol electro-oxidation reaction. These results open the idea of a rational design of co-catalysts based on the tuning of surface chemical properties to eventually enhance exchange current density.
RESUMEN
Gallium arsenide (GaAs) provides a suitable bandgap (1.43 eV) for solar spectrum absorption and allows a larger photovoltage compared to silicon, suggesting great potential as a photoanode toward water splitting. Photocorrosion under water oxidation condition, however, leads to decomposition or the formation of an insulating oxide layer, which limits the photoelectrochemical performance and stability of GaAs. In this work, a self-limiting electrodeposition method of Ni on GaAs is reported to either generate ultra-thin continuous film or nanoislands with high particle density by controlling deposition time. The self-limiting growth mechanism is validated by potential transients, X-ray photoelectron spectroscopy composition and depth profile measurements. This deposition method exhibits a rapid nucleation, forms an initial metallic layer followed by a hydroxide/oxyhydroxide nanofilm on the GaAs surface and is independent of layer thickness versus deposition time when coalescence is reached. A photocurrent up to 8.9 mA cm-2 with a photovoltage of 0.11 V is obtained for continuous ultrathin films, while a photocurrent density of 9.2 mA cm-2 with a photovoltage of 0.50 V is reached for the discontinuous nanoislands layers in an aqueous solution containing the reversible redox couple K3 Fe(CN)6 /K4 Fe(CN)6 .
RESUMEN
We report here the remarkable catalytic efficiency observed for two Pd(II) azamacrocyclic complexes supported on multiwalled carbon nanotubes (MWCNTs) toward oxygen reduction reactions. Beyond a main (>90%) 4e- process and an onset potential close to or better than those of commercial Pt electrodes, the MWCNTs functionalization strategy, aimed at chemically defined Pd(II)-based catalytic centers, allowed the half-cell to exceed the proton-exchange-membrane fuel-cell reference/target mass activity efficiency set by the U.S. Department of Energy for 2020 (440 mA/mgPGM at 0.9 V vs reversible hydrogen electrode).
RESUMEN
In this work, we report the analysis of the electrochemical detection of electroactive species with band microelectrodes that operate under controlled convection. The study focuses on the determination of the collection efficiency of the analyte as a function of inlet flow velocity and microband geometry (inlaid, bumped and recessed), also providing a straightforward method for the theoretical determination of the lower detection limit. The analysis has been carried out by simulating the dimensionless mass transport with the finite element method, delivering the stationary limiting current density. Simulations have been performed on systems consisting of single and double band electrodes to investigate the trail effect on the electrochemical detection. We show that the obtained dimensionless results can be easily turned into dimensional data, providing a tool for the design of devices. The proposed method is general and can easily be extended to systems with different geometry.
RESUMEN
Understanding overfishing and regulating fishing quotas is a major global challenge for the 21st Century both in terms of providing food for humankind and to preserve the oceans' ecosystems. However, fishing is a complex economic activity, affected not just by overfishing but also by such factors as pollution, technology, financial factors and more. For this reason, it is often difficult to state with complete certainty that overfishing is the cause of the decline of a fishery. In this study, we developed a simple dynamic model specifically designed to isolate and to study the role of depletion on production. The model is based on the well-known Lotka-Volterra model, or Prey-Predator mechanism, assuming that the fish stock and the fishing industry are coupled variables that dynamically affect each other. In the model, the fishing industry acts as the "predator" and the fish stock as the "prey". If the model can fit historical data, in particular relative to the productive decline of specific fisheries, then we have a strong indication that the decline of the fish stock is driving the decline of the fishery production. The model doesn't pretend to be a general description of the fishing industry in all its varied forms; however, the data reported here show that the model can describe several historical cases of fisheries whose production decreased and collapsed, indicating that the overexploitation of the fish stocks is an important factor in the decline of fisheries.
RESUMEN
One of the biggest obstacles to the dissemination of fuel cells is their cost, a large part of which is due to platinum (Pt) electrocatalysts. Complete removal of Pt is a difficult if not impossible task for proton exchange membrane fuel cells (PEM-FCs). The anion exchange membrane fuel cell (AEM-FC) has long been proposed as a solution as non-Pt metals may be employed. Despite this, few examples of Pt-free AEM-FCs have been demonstrated with modest power output. The main obstacle preventing the realization of a high power density Pt-free AEM-FC is sluggish hydrogen oxidation (HOR) kinetics of the anode catalyst. Here we describe a Pt-free AEM-FC that employs a mixed carbon-CeO2 supported palladium (Pd) anode catalyst that exhibits enhanced kinetics for the HOR. AEM-FC tests run on dry H2 and pure air show peak power densities of more than 500â mW cm(-2) .
RESUMEN
The combination of two different metals, each of them acting on different steps of the oxygen reduction reaction (ORR), yields synergic catalytic effects. In this respect, the electrocatalytic effect of silver is enhanced by the addition of cobalt, which is able to break the O-O bond of molecular oxygen, thus accelerating the first step of the reduction mechanism. At the same time, research is to further reduce the catalyst's cost, reducing the amount of Ag, which, even though being much less expensive than Pt, is still a noble metal. From this point of view, using a small amount of Ag together with an inexpensive material, such as graphite, represents a good compromise. The aim of this work was to verify if the synergic effects are still operating when very small amounts of cobalt (2-10 µg·cm(-2)) are added to the microparticles of silver electrodeposited on glassy carbon, described in a preceding paper from us. To better stress the different behaviour observed when cobalt and silver are contemporarily present in the deposit, the catalytic properties of cobalt alone were investigated. The analysis was completed by the Levich plots to evaluate the number of electrons involved and by Tafel plots to show the effects on the reaction mechanism.
Asunto(s)
Carbono/química , Cobalto/química , Técnicas Electroquímicas/métodos , Galvanoplastia/métodos , Vidrio/química , Oxígeno/química , Plata/química , Catálisis , Electrodos , Cinética , Oxidación-ReducciónRESUMEN
In this manuscript, a comprehensive study is presented on Fe-based electrocatalysts with mono, bi, and tri-metallic compositions, emphasizing the influence of processing-structure correlations on the electrocatalytic activity for the oxygen reduction reaction (ORR) in the alkaline medium. These electrocatalysts were synthesized through the mixing of transition metal phthalocyanines (TM-Pc) with conductive carbon support, followed by controlled thermal treatment at specific temperatures (600 °C and 900 °C). An extensive analysis was conducted, employing various techniques, including X-ray Absorption Spectroscopy (XAS), Transmission Electron Microscopy (TEM), and X-ray Diffraction (XRD), providing valuable insights into the structural characteristics of the synthesized nanoparticles. Importantly, an increase in the Fe-Pc weight percentage from 10% to 30% enhanced the ORR activity, although not proportionally. Furthermore, a comparative analysis between mono, bi, and tri-metallic samples subjected to different functionalization temperatures highlighted the superior electrocatalytic activity of electrocatalysts functionalized at 600 °C, particularly Fe 600 and Fe-Ni-Cu 600. These electrocatalysts featured Eon values of 0.96 V vs. RHE and E1/2 values of 0.9 V vs. RHE, with the added benefit of reduced anionic peroxide production. The potential of these Fe-based electrocatalysts to enhance ORR efficiency is underscored by this research, contributing to the development of more effective and sustainable electrocatalysts for energy conversion technologies.
RESUMEN
Ionic liquids (ILs) represent promising working fluids to be used in thermal energy storage (TES) technologies thanks to their peculiar properties, such as low volatility, high chemical stability, and high heat capacity. Here, we studied the thermal stability of the IL N-butyl-N-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate ([BmPyrr]FAP), a potential working fluid for TES applications. The IL was heated at 200 °C for up to 168 h either in the absence or in contact with steel, copper, and brass plates to simulate the conditions used in TES plants. High-resolution magic angle spinning nuclear magnetic resonance spectroscopy was found to be useful for the identification of the degradation products of both the cation and the anion, thanks to the acquisition of 1H, 13C, 31P, and 19F-based experiments. In addition, elemental analysis was performed on the thermally degraded samples by inductively coupled plasma optical emission spectroscopy and energy dispersive X-ray spectroscopy. Our analysis shows a significant degradation of the FAP anion upon heating for more than 4 h, even in the absence of the metal/alloy plates; on the other hand, the [BmPyrr] cation displays a remarkable stability also when heated in contact with steel and brass.
RESUMEN
Improved performance through milling: A method for enhancing the catalytic activity of supported metal nanoparticles is reported. This method enhances the activity for the ethanol electro-oxidation of a supported palladium catalyst. The much higher catalytic performance is ascribed to the increased electrochemically active surface area as well as the generation of high-index facets at the milled nanoparticle surface.
RESUMEN
As highlighted by the recent roadmaps from the European Union and the United States, water electrolysis is the most valuable high-intensity technology for producing green hydrogen. Currently, two commercial low-temperature water electrolyzer technologies exist: alkaline water electrolyzer (A-WE) and proton-exchange membrane water electrolyzer (PEM-WE). However, both have major drawbacks. A-WE shows low productivity and efficiency, while PEM-WE uses a significant amount of critical raw materials. Lately, the use of anion-exchange membrane water electrolyzers (AEM-WE) has been proposed to overcome the limitations of the current commercial systems. AEM-WE could become the cornerstone to achieve an intense, safe, and resilient green hydrogen production to fulfill the hydrogen targets to achieve the 2050 decarbonization goals. Here, the status of AEM-WE development is discussed, with a focus on the most critical aspects for research and highlighting the potential routes for overcoming the remaining issues. The Review closes with the future perspective on the AEM-WE research indicating the targets to be achieved.
Asunto(s)
Membranas Artificiales , Agua , Aniones , Electrólisis , HidrógenoRESUMEN
A novel route for the valorization of waste into valuable products was developed. Surgical masks commonly used for COVID 19 protection by stopping aerosol and droplets have been widely used, and their disposal is critical and often not properly pursued. This work intended to transform surgical masks into platinum group metal-free electrocatalysts for oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) as well as into crude oil. Surgical masks were subjected to controlled-temperature and -atmosphere pyrolysis, and the produced char was then converted into electrocatalysts by functionalizing it with metal phthalocyanine of interest. The electrocatalytic performance characterization towards ORR and HER was carried out highlighting promising activity. At different temperatures, condensable oil fractions were acquired and thoroughly analyzed. Transformation of waste surgical masks into electrocatalysts and crude oil can open new routes for the conversion of waste into valuable products within the core of the circular economy.
Asunto(s)
COVID-19 , Petróleo , Humanos , Máscaras , Pirólisis , SARS-CoV-2RESUMEN
The dinuclear Ru diazadiene olefin complex, [Ru2(OTf)(µ-H)(Me2dad)(dbcot)2], is an active catalyst for hydrogen evolution in a Polymer Exchange Membrane (PEM) water electrolyser. When supported on high surface area carbon black and at 80 °C, [Ru2(OTf)(µ-H)(Me2dad)(dbcot)2]@C evolves hydrogen at the cathode of a PEM electrolysis cell (400 mA cm-2, 1.9 V). A remarkable turn over frequency (TOF) of 7800 molH2 molcatalyst -1 h-1 is maintained over 7 days of operation. A series of model reactions in homogeneous media and in electrochemical half cells, combined with DFT calculations, are used to rationalize the hydrogen evolution mechanism promoted by [Ru2(OTf)(µ-H)(Me2dad)(dbcot)2].
RESUMEN
Here, we synthesize a Au@Fe3O4 core@shell system with a highly uniform unprecedented star-like shell morphology with combined plasmonic and magnetic properties. An advanced electron microscopy characterization allows assessing the multifaceted nature of the Au core and its role in the growth of the peculiar epitaxial star-like shell with excellent crystallinity and homogeneity. Magnetometry and magneto-optical spectroscopy revealed a pure magnetite shell, with a superior saturation magnetization compared to similar Au@Fe3O4 heterostructures reported in the literature, which is ascribed to the star-like morphology, as well as to the large thickness of the shell. Of note, Au@Fe3O4 nanostar-loaded cancer cells displayed magneto-mechanical stress under a low frequency external alternating magnetic field (few tens of Hz). On the other hand, such a uniform, homogeneous, and thick magnetite shell enables the shift of the plasmonic resonance of the Au core to 640 nm, which is the largest red shift achievable in Au@Fe3O4 homogeneous core@shell systems, prompting application in photothermal therapy and optical imaging in the first biologically transparent window. Preliminary experiments performing irradiation of a stable water suspension of the nanostar and Au@Fe3O4-loaded cancer cell culture suspension at 658 nm confirmed their optical response and their suitability for photothermal therapy. The outstanding features of the prepared system can be thus potentially exploited as a multifunctional platform for magnetic-plasmonic applications.
Asunto(s)
Óxido Ferrosoférrico , Terapia Fototérmica , Óxido Ferrosoférrico/química , Oro/química , Campos Magnéticos , MagnetismoRESUMEN
Two-dimensional (2D) anatase titanium dioxide (TiO2) is expected to exhibit different properties as compared to anatase nanocrystallites, due to its highly reactive exposed facets. However, access to 2D anatase TiO2 is limited by the non-layered nature of the bulk crystal, which does not allow use of top-down chemical exfoliation. Large efforts have been dedicated to the growth of 2D anatase TiO2 with high reactive facets by bottom-up approaches, which relies on the use of harmful chemical reagents. Here, we demonstrate a novel fluorine-free strategy based on topochemical conversion of 2D 1T-TiS2 for the production of single crystalline 2D anatase TiO2, exposing the {001} facet on the top and bottom and {100} at the sides of the nanosheet. The exposure of these faces, with no additional defects or doping, gives rise to a significant activity enhancement in the hydrogen evolution reaction, as compared to commercially available Degussa P25 TiO2 nanoparticles. Because of the strong potential of TiO2 in many energy-based applications, our topochemical approach offers a low cost, green and mass scalable route for production of highly crystalline anatase TiO2 with well controlled and highly reactive exposed facets.
RESUMEN
We present the thickness measurement of multilayer samples by X-ray fluorescence (XRF) using calibration curves obtained from simulated spectra through Monte Carlo (MC) algorithm. The XRF is a widespread technique for the analysis of single and multilayer films but the accuracy of quantitative analysis must be increased. Moreover, the use certified standards is not easy to implement due to the high variability of combination and/or concentration in layered samples. The results of this work were compared with fundamental parameter (FP) method and focussed ion beam scanning electron microscopy (FIB-SEM) analysis. The results show good quantitative values even without the use of any standard with known thickness. In addition to having built the calibration curves with a simple univariate approach, also multivariate data analysis was performed to consider multiple variables simultaneously. From the comparison of the obtained results, it can be inferred that the univariate analysis worked well in the case of single layer samples and in the determination of the upper layer in multilayer samples but only multivariate analysis, taking into account the matrix effect of each layer, provided maximum accuracy on each layer of multilayer samples.
RESUMEN
Ionic Liquids are a promising alternative to water electrolytes for the electrodeposition of metals. These solvents have a much larger electrochemical window than water that expands the potential of electrodeposition. However, mass transport in Ionic Liquids is slow. The slow mass transport dramatically affects the rate of reactions at the solid-liquid interface, hampering the exploitation of Ionic Liquids in high-throughput electrodeposition processes. In this paper, we clarify the origin of such poor mass transport in the diffusion-advection (convection) regime. To determine the extent and the dynamics of the convection boundary layers, we performed Rotating Disk Electrode (RDE) experiments on model reactions along with the finite element simulation. Both the experiments and the finite element modelling showed the occurrence of peaks in the RDE curves even at relatively high rotation rates (up to 2000 rpm). The peak in the RDE is the fingerprint of partial diffusion control that happens for the relative extent of the diffusion and convection boundary layers. In looking for a close match between the experiments and the simulations, we found that the ohmic drop plays a critical role and must be considered in the calculation to find the best match with the experimental data. In the end, we have shown that the combined approach consisting of RDE experiments and finite elements modelling providing a tool to unravel of the structure of the diffusion and convection boundary layers both in dynamic and stationary conditions.
RESUMEN
Spin crossover complexes are among the most studied classes of molecular switches and have attracted considerable attention for their potential technological use as active units in multifunctional devices. A fundamental step toward their practical implementation is the integration in macroscopic devices adopting hybrid vertical architectures. First, the physical properties of technological interest shown by these materials in the bulk phase have to be retained once they are deposited on a solid surface. Herein, we describe the study of a hybrid molecular inorganic junction embedding the spin crossover complex [Fe(qnal)2] (qnal = quinoline-naphthaldehyde) as an active switchable thin film sandwiched within energy-optimized metallic electrodes. In these junctions, developed and characterized with the support of state of the art techniques including synchrotron Mössbauer source (SMS) spectroscopy and focused-ion beam scanning transmission electron microscopy, we observed that the spin state conversion of the Fe(II)-based spin crossover film is associated with a transition from a space charge-limited current (SCLC) transport mechanism with shallow traps to a SCLC mechanism characterized by the presence of an exponential distribution of traps concomitant with the spin transition temperature.
RESUMEN
CdSe electrodeposition on n-Si (100) substrate was investigated in sulfuric acid solution. The behaviour and the deposition of the precursors (Cd and Se) were studied separately at first. Then, we explored both the alternated deposition, one layer by one, as well as the simultaneous co-deposition of the two elements to form the CdSe semiconductor. Varying the deposition conditions, we were able to obtain nanoparticles, or a thin film, on the surface of the electrode. The samples were then characterised microscopically and spectroscopically with SEM, XRD and XPS. Finally, we evaluated the induced photoemission of the deposit for the application in optoelectronics.