RESUMEN
Incorporating a third component into binary organic solar cells (b-OSCs) has provided a potential platform to boost power conversion efficiency (PCEs). However, gaining control over the non-equilibrium blend morphology via the molecular design of the perylene diimide (PDI)-based third component toward efficient ternary organic solar cells (t-OSCs) still remains challenging. Herein, two novel PDI derivatives are developed with tailored molecular planarity, namely ufBTz-2PDI and fBTz-2PDI, as the third component for t-OSCs. Notably, after performing a cyclization reaction, the twisted ufBTz-2PDI with an amorphous character transferred to the highly planar fBTz-2PDI followed by a semi-crystalline character. When incorporating the semi-crystalline fBTz-2PDI into the D18:L8-BO system, the resultant t-OSC achieved an impressive PCE of 18.56%, surpassing the 17.88% attained in b-OSCs. In comparison, the addition of amorphous ufBTz-2PDI into the binary system facilitates additional charge trap sites and results in a deteriorative PCE of 14.37%. Additionally, The third component fBTz-2PDI possesses a good generality in optimizing the PCEs of several b-OSCs systems are demonstrated. The results not only provided a novel A-DA'D-A motif for further designing efficient third component but also demonstrated the crucial role of modulated crystallinity of the PDI-based third component in optimizing PCEs of t-OSCs.
RESUMEN
Achieving both high power conversion efficiency (PCE) and device stability is a major challenge for the practical development of organic solar cells (OSCs). Herein, three non-fully conjugated dimerized giant acceptors (named 2Y-sites, including wing-site-linked 2Y-wing, core-site-linked 2Y-core, and end-site-linked 2Y-end) are developed. They share the similar monomer precursors but have different alkyl-linked sites, offering the fine-tuned molecular absorption, packing, glass transition temperature, and carrier mobility. Among their binary active layers, D18/2Y-wing has better miscibility, leading to optimized morphology and more efficient charge transfer compared to D18/2Y-core and D18/2Y-end. Therefore, the D18/2Y-wing-based OSCs achieve a superior PCE of 17.73 %, attributed to enhanced photocurrent and fill factor. Furthermore, the D18/2Y-wing-based OSCs exhibit a balance of high PCE and improved stability, distinguishing them within the 2Y-sites. Building on the success of 2Y-wing in binary systems, we extend its application to ternary OSCs by pairing it with the near-infrared absorbing D18/BS3TSe-4F host. Thanks to the complementary absorption within 300-970â nm and further optimized morphology, ternary OSCs obtain a higher PCE of 19.13 %, setting a new efficiency benchmark for the dimer-derived OSCs. This approach of alkyl-linked site engineering for constructing dimerized giant acceptors presents a promising pathway to improve both PCE and stability of OSCs.
RESUMEN
With the rapid development of small-molecule electron acceptors, polymer electron donors are becoming more important than ever in organic photovoltaics, and there is still room for the currently available high-performance polymer donors. To further develop polymer donors with finely tunable structures to achieve better photovoltaic performances, random ternary copolymerization is a useful technique. Herein, by incorporating a new electron-withdrawing segment 2,3-bis(3-octyloxyphenyl)dithieno[3,2-f:2',3'-h]quinoxaline derivative (C12T-TQ) to PM6, a series of terpolymers were synthesized. It is worth noting that the introduction of the C12T-TQ unit can deepen the highest occupied molecular orbital energy levels of the resultant polymers. In addition, the polymer Z6 with a 10% C12T-TQ ratio possesses the highest film absorption coefficient (9.86 × 104 cm-1) among the four polymers. When blended with Y6, it exhibited superior miscibility and mutual crystallinity enhancement between Z6 and Y6, suppressed recombination, better exciton separation and charge collection characteristics, and faster hole transfer in the D-A interface. Consequently, the device of Z6:Y6 successfully achieved enhanced photovoltaic parameters and yielded an efficiency of 17.01%, higher than the 16.18% of the PM6:Y6 device, demonstrating the effectiveness of the meta-octyloxy-phenyl-modified dithieno[3,2-f:2',3'-h]quinoxaline moiety to build promising terpolymer donors for high-performance organic solar cells.
RESUMEN
Great progress has been made in organic solar cells (OSCs) in recent years, especially after the report of the highly efficient small-molecule electron acceptor Y6. However, the relatively low open circuit voltage (VOC) and unbalanced charge mobilities remain two issues that need to be resolved for further improvement in the performance of OSCs. Herein, a wide-band-gap amorphous acceptor IO-4Cl, which possessed a shallower lowest unoccupied molecular orbital (LUMO) energy level than Y6, was introduced into the PM6:Y6 binary system to construct a ternary device. The mechanism study revealed that the introduced IO-4Cl was alloyed with Y6 to prevent the overaggregation of Y6 and offer dual channels for effective hole transportation, resulting in balanced hole and electron mobilities. Taking these advantages, an enhanced VOC of 0.894 V and an improved fill factor of 75.58% were achieved in the optimized PM6:Y6:IO-4Cl-based ternary device, yielding a promising power conversion efficiency (PCE) of 17.49%, which surpassed the 16.72% efficiency of the PM6:Y6 binary device. This work provides an alternative solution to balance the charge mobilities of PM6:Y6-based devices by incorporating an amorphous high-performance LUMO A-D-A small molecule as the third compound.
RESUMEN
Halogenation of Y-series small-molecule acceptors (Y-SMAs) is identified as an effective strategy to optimize photoelectric properties for achieving improved power-conversion-efficiencies (PCEs) in binary organic solar cells (OSCs). However, the effect of different halogenation in the 2D-structured large π-fused core of guest Y-SMAs on ternary OSCs has not yet been systematically studied. Herein, four 2D-conjugated Y-SMAs (X-QTP-4F, including halogen-free H-QTP-4F, chlorinated Cl-QTP-4F, brominated Br-QTP-4F, and iodinated I-QTP-4F) by attaching different halogens into 2D-conjugation extended dibenzo[f,h]quinoxaline core are developed. Among these X-QTP-4F, Cl-QTP-4F has a higher absorption coefficient, optimized molecular crystallinity and packing, suitable cascade energy levels, and complementary absorption with PM6:L8-BO host. Moreover, among ternary PM6:L8-BO:X-QTP-4F blends, PM6:L8-BO:Cl-QTP-4F obtains a more uniform and size-suitable fibrillary network morphology, improved molecular crystallinity and packing, as well as optimized vertical phase distribution, thus boosting charge generation, transport, extraction, and suppressing energy loss of OSCs. Consequently, the PM6:L8-BO:Cl-QTP-4F-based OSCs achieve a 19.0% efficiency, which is among the state-of-the-art OSCs based on 2D-conjugated Y-SMAs and superior to these devices based on PM6:L8-BO host (17.70%) and with guests of H-QTP-4F (18.23%), Br-QTP-4F (18.39%), and I-QTP-4F (17.62%). The work indicates that halogenation in 2D-structured dibenzo[f,h]quinoxaline core of Y-SMAs guests is a promising strategy to gain efficient ternary OSCs.