Magnetic-field-assisted optical fiber quantum temperature sensor with enhanced sensitivity.

In recent years, utilizing nitrogen-vacancy color centers in diamond for temperature sensing has drawn great attention. However, increasing the sensitivity has encountered challenges due to the intrinsic temperature-dependent energy level shift, i.e., temperature responsivity, being limited to -74 kHz/K. In this Letter, we take advantage of the magnetic field to regulate the energy level to enhance temperature sensitivity. The sensor is formed by adhering a micron-sized diamond on the end face of an optical fiber, and a small magnet is mounted at a certain distance with the diamond exploiting a cured polydimethylsiloxane block as the bridge. The temperature change leads to the variation of the distance between the diamond and the magnet, thus affecting the magnetic strength felt by the diamond. This finally contributes an additional temperature-induced energy level shift, giving rise to an enhanced sensitivity. Experimental results demonstrated the proposed scheme and achieved a 4.2-fold improvement in the temperature responsivity and a 2.1-fold enhancement in sensitivity. Moreover, the diamond and the fiber-optic integrated structure improve the portability of the sensor.

High-sensitivity optical-fiber magnetic sensor based on diamond and magnetic flux concentrators.

Magnetic field detection exploiting nitrogen-vacancy (NV) centers in diamond has gained increasing attention and development in recent years. Combining diamond NV centers to optical fibers provides a way for achieving magnetic sensors with high integration and portability. Meanwhile, new methods or techniques are urgently desired to improve the detection sensitivity of such sensors. In this paper, we present an optical-fiber magnetic sensor based on the NV ensemble in diamond, and employ the well-designed magnetic flux concentrators to enhance the sensitivity up to 12 pT/Hz1/2, an outstanding level among the diamond-integrated optical-fiber magnetic sensors. The dependence of sensitivity on the key parameters including the size and gap width of the concentrators are investigated by simulations and experiments, based on which the predictions on the further enhancement of sensitivity to fT level are presented.

Ultrahigh-sensitive and compact temperature sensor based on no-core fiber with PMMA coating.

A new mechanism between the temperature sensitivity and the length ratio of PMMA coating to no-core fiber (NCF) is reported to realize an optical fiber temperature sensor with ultra-high sensitivity and compact size by PMMA-coated no-core fiber. By both theory and experiment, it is found that the sensitivity has a linear response to the length ratio of PMMA coating to NCF rather than the conventional viewpoint that it depends on the length of PMMA. Based on this conclusion and the high thermo-optic coefficient of PMMA, the temperature sensitivity is significantly enhanced as high as -9.582 nm/℃ through a simple, compact, and inexpensive sensor with 5 mm NCF and 3 mm PMMA coating. Our work opens a new avenue of a significant increase in the detection sensitivity of miniaturized fiber temperature sensors.

Exploiting black phosphorus based-Tamm plasmons in the terahertz region.

Polarization-sensitive Tamm plasmons are investigated in a multi-layer photonic configuration where a monolayer black phosphorus (BP) is coated on a Bragg mirror separated by a dielectric. Owing to the in-plane anisotropy of BP, the Tamm plasmon can be excited selectively by tuning the BP carrier density. Cross-polarization conversion occurs when the armchair direction of BP makes an angle with the incident plan, i.e., ϕ≠0 or 90°. The BP-based Tamm device can be used as an intensity modulator with a modulation depth up to ∼100% and an insertion loss smaller than -0.55 dB. By analyzing the polarization evolution carefully, a multichannel polarization division multiplexing scheme is proposed and discussed. These findings open a new avenue for exploiting versatile tunable THz devices based on the monolayer of BP.

Ultrafast freestanding microfiber humidity sensor based on three-dimensional graphene network cladding.

An all-fiber humidity sensor is proposed and fabricated by depositing three-dimensional graphene network (3DGN) around the surface of a freestanding microfiber (MF). The high specific surface area and porosity of 3DGN enhances its interaction with water molecules, allowing high performance of the humidity sensor. The sensor can operate in a wide relative humidity (RH) range of 11.6%RH-90.9%RH with a high sensitivity of -2.841 dB/%RH in the RH range (80.3%RH - 90.9%RH). The response and recovery times of this type of microfiber sensor are measured respectively to be 57 ms and 55 ms, which are one order magnitude faster than those of other fiber RH sensors activated by two-dimensional materials coating. Such an all-fiber RH sensor with high sensitivity and fast response property possesses great potential of application in widespread fields, such as biology, chemical processing and food processing.

High-performance fiber plasmonic sensor by engineering the dispersion of hyperbolic metamaterials composed of Ag/TiO2.

Hyperbolic metamaterials (HMMs) have attracted increasing attentions because of their unique dispersion properties and the flexibility to control the dispersion by changing the components and fractions of the composed materials. In this work, for the first time, we demonstrate a plasmonic sensor based on a side-polished few-mode-fiber coated with a layered of HMM, which is composed of alternating layers of Ag and TiO2. To optimize the sensor performance, the effects of the metal filling fraction (ρ) and the number of bilayers (Nbi) on the HMM dispersion are thoroughly engineered with the effective medium theory and the finite element method. It is found that the HMM with ρ=0.7 and Nbi = 3 can provide the average sensitivity of 5114.3 nm/RIU (RIU: refractive index unit), and the highest sensitivity 9000 nm/RIU in the surrounding refractive index (SRI) ranging from 1.33 to 1.40 RIU. The corresponding figure of merit (FOM) reaches a maximum of 230.8 RIU-1 which is much higher than that of the conventional silver film based SPR sensor. The influence of ρ and Nbi on the sensitivity are well explained from the aspects of the electrical field distribution and the dispersion relationship. This work opens a gate to significantly improve fiber plasmonic sensors performance by engineering the HMM dispersion, which is expected to meet the emergent demand in the biological, medical and clinical applications.

Residual thickness enhanced core-removed D-shaped single-mode fiber and its application for VOC evaporation monitoring.

A core-removed D-shaped structure with different residual thickness (RT) was manufactured on a single mode silica fiber (SMF) to enhance the sensitivity by using of ultra-precise polishing technology. With six different RTs ranging from ∼55 µm to ∼28 µm, the RT enhancement effect in a D-shaped SMF was researched in detail. The influence of the RT on its transmission spectra was investigated both theoretically and experimentally. Considering a compromise between the multimode interference efficiency and optical power loss, an optimum RT value of 34.09 µm was achieved. The obtained refractive index (RI) sensitivity was 10243 nm/RIU in the RI range of 1.430-1.444, corresponding to a RI resolution of 1.9×10-6 RIU. A high-performance all-fiber sensor was developed to monitor the evaporation process volatile organic compounds (VOCs) based on the RT-enhanced D-shaped SMF. As proof of concept, a 2-hour continuous monitoring was carried to monitor the chloroform and alcohol mixture. As a result, the evaporation of alcohol and chloroform were clearly identified and monitored. The developed RT-enhanced D-shaped fiber sensor provides an alternative way for chemical process monitoring and industrial applications.

Half-side gold-coated hetero-core fiber for highly sensitive measurement of a vector magnetic field.

A highly sensitive surface plasmon resonance fiber sensor for a vector magnetic field is proposed. The sensor is composed of a half-side gold-coated multimode-single-mode-multimode hetero-core fiber structure encapsulated with ferrofluids. The half-side gold film on the fiber not only produces the surface plasmon resonance, but also breaks the centrosymmetry of the light field in the fiber. Moreover, the magnetic-field-dependent anisotropy of the surrounding ferrofluids makes the sensor sensitive to both the intensity and direction of the magnetic field. Owing to the unique half-side coating configuration and the resulting enhancement of the evanescent field, the sensor can achieve a sensitivity as high as 1008 pm/Oe to the magnetic field intensity. The proposed sensor, possessing advantages such as high sensitivity, ease of fabrication, and low cost, has potential in the detection of a weak vector magnetic field.

A portable optical fiber SPR temperature sensor based on a smart-phone.

In this paper, a fiber-optic temperature sensing system, based on surface plasmon resonance (SPR) and integrated with a smart-phone platform, is proposed and demonstrated. The sensing system is composed of a side-polished-fiber-based SPR sensor, which is illuminated by the LED flash from one end, and the output signals are recorded and processed by the camera and a designed application in the smart-phone. The sensing performance is evaluated by immersing the sensor in distilled water under different temperatures. Experimental results show that the measurement resolution of the proposed temperature sensor can reach 0.83°C in the range from 30 to 70°C, corresponding to a linear correlation coefficient of 0.9798. The low-cost and portable fiber optic SPR sensor based on a smart-phone platform has wide application potentials in the fields of health-care, environmental monitoring, etc.

Electron-plasmon interaction on lithium niobate with gold nanolayer and its field distribution dependent modulation.

Surface plasmon resonance (SPR) enables strong field confinement, opening thereby new avenues for device miniaturization and reducing energy consumption. Plasmonic devices with electrical tunability attract tremendous interest for various applications. Most of the current researches achieved SPR modulation with relatively large driving voltages, or by other relatively low-speed tuning approaches, such as thermo-optic, magneto-optic, acousto-optic etc. In this paper, we propose and demonstrate an efficiently electrical SPR modulation based on lithium niobate (LN) with gold nanolayer (~81 nm) via electron-plasmon interaction. Efficient intensity modulation and wavelength shift (in visible band) of ~5.7 dB/V and ~36.3 nm/V are respectively obtained with low DC current. More importantly, modulation phenomenon of field distribution dependent is also observed and experimentally unveiled. Further performance is analyzed in terms of AC modulation and polarization characteristics. This key achievement opens up opportunities for applications such as optical interconnection, electric field sensing, electrically plasmonic modulation, etc.

Side-polished few-mode fiber based surface plasmon resonance biosensor.

The fiber geometry, fiber parameters and mode-guiding properties are crucial for realizing high-performance fiber-based sensors. In this work, we propose and demonstrate a few-mode fiber (FMF)-based surface plasmon resonance (SPR) biosensor. The FMF-SPR sensor was fabricated via side-polishing a few-mode fiber and coating a thin layer of gold film, on the basis of the optimization of fiber geometry, thickness of the gold film and mode selection, which were performed with the finite element method. The refractive index (RI) sensing performance of three such sensors with different residual fiber thicknesses were investigated. In the RI range from 1.333 to 1.404, the highest sensitivity up to 4903 nm/RIU and a figure of merit of 46.1 RIU-1 are achieved. For testing the bovine serum albumin (BSA) solution, an averaged BSA RI sensitivity of 6328 nm/RIU and an averaged BSA concentration sensitivity of 1.17 nm/(mg/ml) are realized. Benefiting from only a few modes supported in the FMF, a smaller line-width of the SPR spectrum is obtained, which further results in a higher figure of merit (FOM). Moreover, when combined with the superiority of the mode-multiplexing technology brought by the FMF, the FMF-SPR sensors may find applications in biochemical analysis with high performance and high throughputs.

Tunable asymmetric spin splitting by black phosphorus sandwiched epsilon-near-zero-metamaterial in the terahertz region.

In-plane photonic spin splitting effect is investigated in tunneling terahertz waves through an epsilon-near-zero metamaterial sandwiched between monolayer black phosphorus (BP). The strong in-plane anisotropy of BP layers will induce in-plane asymmetric spin splitting. The asymmetric spin splitting can be flexibly tuned by the angles between the incident plane and the armchair crystalline directions of the top and bottom BP layers, i.e., ϕ1 and ϕ2. Based on this, an angle-resolved barcode-encryption scheme is discussed. For the special case of ϕ1 = ϕ2 = 0 or 90°, the transmitted beam undergoes Goos-Hänchen shift, which varies with the carrier density of BP. We believe these findings can facilitate the development of novel optoelectronic devices in the Terahertz region.

Broadband all-light-control with WS2 coated microfibers.

All-optical light amplitude tuning functionality is demonstrated in a layered tungsten disulfide (WS2) nanosheets coated microfiber (MF) structure. Due to the strong light-matter interactions between WS2 nanosheets and the evanescent field around the MF, a large variation in the transmitted power can be observed under both external and internal pump light excitations over a broadband spectrum (~100 nm). A power variation rate of ~0.3744 dB/mW is obtained under external violet pump light excitation, whereas the power variation rate of similar devices in the state of the art are usually less than 0.3 dB/mW. In terms of the response time, a moderate rise/fall time of ∼20.5/19.6 ms is achieved, which is mainly limited by the employed structure fabrication methods. These results indicate that the optical transmitted power of the WS2 coated MF can be modulated by different pump light with the power in the order of mW, thus the proposed device might have potential applications in all optical controllable devices and sensors, etc.

Electro-optic deflection in a lithium niobate quasi-single mode waveguide with microstructured electrodes.

We propose an electro-optic mode deflection device based on an annealed proton exchange (APE) waveguide in lithium niobate, associated with isosceles-triangle-shaped array electrodes and a horn-shaped input waveguide. The input waveguide is tapered down to ensure that the output of the device has a good beam quality, i.e., a quasi-single mode in this case. This new device allows beam deflection at a relative low voltage and large deflection angle. At an APE-waveguide width of 80 µm, mode deflections of 0.265 and 0.240 µm/V are obtained for 1064 and 980 nm, respectively. This beam deflection device can be applied in high-speed optical switch, and beam smoothing of a high-power laser, etc.

Theoretical investigation of optical modulators based on graphene-coated side- polished fiber.

The effective mode index (EMI) of a graphene-coated side-polished fiber (GSPF) is calculated numerically. Whereby, the influences of graphene atom layer number, residual radius of SPF, light frequency, scattering rate of graphene, and temperature on the EMI are investigated comprehensively. Two types of mechanisms for the electro-optical absorption modulation are found for such GSPF-based modulator. One mechanism is Pauli blocking effect (PBE) and the other is plasmonic attenuation effect (PAE). With the optimal design parameters, a PBE-based modulator is theoretically predicted to have a 0.0072 dB/µm modulation depth, 2.92 V driving voltage swing, 6.35 nJ/bit power consumption, and 56.2 THz optical modulation bandwidth. It is also predicted that a PAE-based modulator could have a 0.0056 dB/µm modulation depth, 0.6 V driving voltage swing, 0.27 nJ/bit power consumption, and 2.5 THz optical modulation bandwidth. By further optimization, the modulator performance such as the relatively high power consumption and the narrow operation bandwidth can be improved. Owing to their seamless connection to optical fiber networks, the GSPF-based modulators have great potential to be used in fast and high-capacity optical communication systems.

Highly sensitive all-optical control of light in WS2 coated microfiber knot resonator.

All-optical light-control-light functionality is realized in a layered tungsten disulfide (WS2) nanosheet coated microfiber knot resonator (MKR) structure. Mainly due to the photon generated excitons induced refractive index variation in WS2 nanosheets, a large variation in the transmitted power (∆T) can be observed under external violet/red laser excitation. The ∆T variation rates can reach up to ~0.4 dB/mW under violet pump light excitation whereas the state of the art light-control-light structures usually has a variation rate of less than 0.25 dB/mW. In terms of the response time, the averaged rise/fall time is ~0.12/0.1 s. The demonstrated structure has the advantages of easy fabrication, low cost and high sensitivity, therefore, it might be a promising candidate for building future all-fiber-optics based functional devices and all-optical circuitry.

Sensitivity-enhanced surface plasmon sensor modified with MoSe2 overlayer.

In this work, a sensitivity-enhanced surface plasmon resonance (SPR) sensor, which is integrated with MoSe2 as modification overlayer, is proposed and investigated. The sensor is constructed by physically depositing MoSe2 onto the surface of a conventional SPR sensor based on Krestchman configuration. Thanks to the commendable properties of MoSe2 including high carrier mobility, high refractive index (RI), large surface area, and so forth, adding an overlayer within a certain thickness can effectively improve the RI sensitivity. Experimental results show that, with the increased number of deposition cycles-which positively correlates with the duty ratio and the MoSe2 overlayer's thickness-the sensitivity at first increases, and then declines. The highest sensitivity of 2524.8 nm/RIU is achieved experimentally, which corresponds to the 2 deposition cycles. This shows an improvement of 36.3%, compared with the case without the MoSe2 modification. The ease of fabrication, efficiency of performance enhancement, and great potentials (such as the large surface area of MoSe2 for linking abundant functional groups) allow the method presented in this paper to contribute to the development of performance-enhanced SPR sensors for the biological, chemical, and medical fields.

Titanium dioxide nanoparticle modified plasmonic interface for enhanced refractometric and biomolecular sensing.

A surface plasmon resonance (SPR) biosensor, which contains an overlayer of titanium dioxide nanoparticles (TDNPs) to modify the plasmonic interface, has been developed and investigated. Owing to its large surface area and high refractive index, the TDNP overlayer significantly enhances the probing electric field intensity and detection sensitivity. This sensitivity is related to the TDNP overlayer thickness, which can be engineered by changing the TiO2-ethanol dispersion's spin-coating concentration. The highest refractive index sensitivity for ethylene glycol measurement is 2567.3 nm/RIU, which is 38% higher than that of a conventional SPR sensor with an uncoated gold film. The proposed TDNP-SPR sensor also exhibits a 1.59-fold sensitivity enhancement in fetal bovine serum detection. Moreover, the proposed interface modification approach that is applied without additional biochemical amplification steps is chemical-free and contamination-free; therefore this TDNP-SPR sensor could be integrated into a sensitive, cost-effective, and biocompatible platform for rapid and label-free biochemical detection.

High-sensitivity vector magnetic field sensor based on side-polished fiber plasmon and ferrofluid.

A high-sensitivity vector magnetic field is proposed and demonstrated. The sensor consists of a side-polished-fiber (SPF)-based surface plasmon resonance (SPR) structure integrated with ferrofluid. Because of the high refractive index sensitivity of the SPR scheme and the outstanding magneto optical properties of ferrofluid, the sensor shows a high sensitivity (up to 598.7 pm/Oe) to magnetic field intensity. Moreover, owing to the non-circular-symmetric geometry of the SPF and non-uniform distribution of the ferrofluid around the SPF, the sensor exhibits a sensitivity of -5.63 nm/deg to the orientation of the magnetic field. The proposed vector magnetic field sensor, integrating over magnetic, plasmonic, and fiber-optic schemes, is highly sensitive to both the intensity and orientation of the magnetic field simultaneously, and holds potential in applications in many fields, such as medicine, industry, and the military.

Ultrasensitive Mach-Zehnder Interferometric Temperature Sensor Based on Liquid-Filled D-Shaped Fiber Cavity.

A liquid-filled D-shaped fiber (DF) cavity serving as an in-fiber Mach–Zehnder interferometer (MZI) has been proposed and experimentally demonstrated for temperature sensing with ultrahigh sensitivity. The miniature MZI is constructed by splicing a segment of DF between two single-mode fibers (SMFs) to form a microcavity (MC) for filling and replacement of various refractive index (RI) liquids. By adjusting the effective RI difference between the DF and MC (the two interference arms), experimental and calculated results indicate that the interference spectra show different degrees of temperature dependence. As the effective RI of the liquid-filled MC approaches that of the DF, temperature sensitivity up to −84.72 nm/°C with a linear correlation coefficient of 0.9953 has been experimentally achieved for a device with the MC length of 456 μm, filled with liquid RI of 1.482. Apart from ultrahigh sensitivity, the proposed MCMZI device possesses additional advantages of its miniature size and simple configuration; these features make it promising and competitive in various temperature sensing applications, such as consumer electronics, biological treatments, and medical diagnosis.