Tough and Fatigue Resistant Cellulose Nanocrystal Stitched Ti3 C2 Tx MXene Films.

Ti3 C2 Tx MXene (or "MXene" for simplicity) has gained noteworthy attention for its metal-like electrical conductivity and high electrochemical capacitance-a unique blend of properties attractive toward a wide range of applications such as energy storage, healthcare monitoring, and electromagnetic interference shielding. However, processing MXene architectures using conventional methods often deals with the presence of defects, voids, and isotropic flake arrangements, resulting in a trade-off in properties. Here, a sequential bridging (SB) strategy is reported to fabricate dense, freestanding MXene films of interconnected flakes with minimal defects, significantly enhancing its mechanical properties, specifically tensile strength (≈285 MPa) and breaking energy (≈16.1 MJ m-3 ), while retaining substantial values of electrical conductivity (≈3050 S cm-1 ) and electrochemical capacitance (≈920 F cm-3 ). This SB method first involves forming a cellulose nanocrystal-stitched MXene framework, followed by infiltration with structure-densifying calcium cations (Ca2+ ), resulting in tough and fatigue resistant films with anisotropic, evenly spaced, and strongly interconnected flakes - properties essential for developing high-performance energy-storage devices. It is anticipated that the knowledge gained in this work will be extended toward improving the robustness and retaining the electronic properties of 2D nanomaterial-based macroarchitectures.

Highly Conductive Ti3 C2 Tx MXene Hybrid Fibers for Flexible and Elastic Fiber-Shaped Supercapacitors.

Fiber-shaped supercapacitors (FSCs) are promising energy storage solutions for powering miniaturized or wearable electronics. However, the scalable fabrication of fiber electrodes with high electrical conductivity and excellent energy storage performance for use in FSCs remains a challenge. Here, an easily scalable one-step wet-spinning approach is reported to fabricate highly conductive fibers using hybrid formulations of Ti3 C2 Tx MXene nanosheets and poly(3,4-ethylenedioxythiophene):polystyrene sulfonate. This approach produces fibers with a record conductivity of ≈1489 S cm-1 , which is about five times higher than other reported Ti3 C2 Tx MXene-based fibers (up to ≈290 S cm-1 ). The hybrid fiber at ≈70 wt% MXene shows a high volumetric capacitance (≈614.5 F cm-3 at 5 mV s-1 ) and an excellent rate performance (≈375.2 F cm-3 at 1000 mV s-1 ). When assembled into a free-standing FSC, the energy and power densities of the device reach ≈7.13 Wh cm-3 and ≈8249 mW cm-3 , respectively. The excellent strength and flexibility of the hybrid fibers allow them to be wrapped on a silicone elastomer fiber to achieve an elastic FSC with 96% capacitance retention when cyclically stretched to 100% strain. This work demonstrates the potential of MXene-based fiber electrodes and their scalable production for fiber-based energy storage applications.

Knitting Elastic Conductive Fibers of MXene/Natural Rubber for Multifunctional Wearable Sensors.

Wearable electronic sensors have recently attracted tremendous attention in applications such as personal health monitoring, human movement detection, and sensory skins as they offer a promising alternative to counterparts made from traditional metallic conductors and bulky metallic conductors. However, the real-world use of most wearable sensors is often hindered by their limited stretchability and sensitivity, and ultimately, their difficulty to integrate into textiles. To overcome these limitations, wearable sensors can incorporate flexible conductive fibers as electrically active components. In this study, we adopt a scalable wet-spinning approach to directly produce flexible and conductive fibers from aqueous mixtures of Ti3C2Tx MXene and natural rubber (NR). The electrical conductivity and stretchability of these fibers were tuned by varying their MXene loading, enabling knittability into textiles for wearable sensors. As individual filaments, these MXene/NR fibers exhibit suitable conductivity dependence on strain variations, making them ideal for motivating sensors. Meanwhile, textiles from knitted MXene/NR fibers demonstrate great stability as capacitive touch sensors. Collectively, we believe that these elastic and conductive MXene/NR-based fibers and textiles are promising candidates for wearable sensors and smart textiles.

Applications of X-Ray-Based Characterization in MXene Research.

X-rays are a penetrating form of high-energy electromagnetic radiation with wavelengths ranging from 10 pm to 10 nm. Similar to visible light, X-rays provide a powerful tool to study the atoms and elemental information of objects. Different characterization methods based on X-rays are established, such as X-ray diffraction, small- and wide-angle X-ray scattering, and X-ray-based spectroscopies, to explore the structural and elemental information of varied materials including low-dimensional nanomaterials. This review summarizes the recent progress of using X-ray related characterization methods in MXenes, a new family of 2D nanomaterials. These methods provide key information on the nanomaterials, covering synthesis, elemental composition, and the assembly of MXene sheets and their composites. Additionally, new characterization methods are proposed as future research directions in the outlook section to enhance understanding of MXene surface and chemical properties. This review is expected to provide a guideline for characterization method selection and aid in precise interpretation of the experimental data in MXene research.

Environmentally stable MXene ink for direct writing flexible electronics.

MXene inks are promising candidates for fabricating conductive circuits and flexible devices. Here, MXene inks prepared from solvent mixtures demonstrate long-term stability and can be employed in commercial rollerball pens to write electronic circuits on flexible substrates. Such circuits exhibit a fast and accurate capacitive response for touch-boards and water level measurement, indicating the excellent potential of these MXene inks in electrical device fabrication.

Scalable Manufacturing of Free-Standing, Strong Ti3 C2 Tx MXene Films with Outstanding Conductivity.

Free-standing films that display high strength and high electrical conductivity are critical for flexible electronics, such as electromagnetic interference (EMI) shielding coatings and current collectors for batteries and supercapacitors. 2D Ti3 C2 Tx flakes are ideal candidates for making conductive films due to their high strength and metallic conductivity. It is, however, challenging to transfer those outstanding properties of single MXene flakes to macroscale films as a result of the small flake size and relatively poor flake alignment that occurs during solution-based processing. Here, a scalable method is shown for the fabrication of strong and highly conducting pure MXene films containing highly aligned large MXene flakes. These films demonstrate record tensile strength up to ≈570 MPa for a 940 nm thick film and electrical conductivity of ≈15 100 S cm-1 for a 214 nm thick film, which are both the highest values compared to previously reported pure Ti3 C2 Tx films. These films also exhibit outstanding EMI shielding performance (≈50 dB for a 940 nm thick film) that exceeds other synthetic materials with comparable thickness. MXene films with aligned flakes provide an effective route for producing large-area, high-strength, and high-electrical-conductivity MXene-based films for future electronic applications.

Additive-Free MXene Liquid Crystals and Fibers.

The discovery of liquid crystalline (LC) phases in dispersions of two-dimensional (2D) materials has enabled the development of macroscopically aligned three-dimensional (3D) macrostructures. Here, we report the first experimental observation of self-assembled LC phases in aqueous Ti3C2T x MXene inks without using LC additives, binders, or stabilizing agents. We show that the transition concentration from the isotropic to nematic phase is influenced by the aspect ratio of MXene flakes. The formation of the nematic LC phase makes it possible to produce fibers from MXenes using a wet-spinning method. By changing the Ti3C2T x flake size in the ink formulation, coagulation bath, and spinning parameters, we control the morphology of the MXene fibers. The wet-spun Ti3C2T x fibers show a high electrical conductivity of ∼7750 S cm-1, surpassing existing nanomaterial-based fibers. A high volumetric capacitance of ∼1265 F cm-3 makes Ti3C2T x fibers promising for fiber-shaped supercapacitor devices. We also show that Ti3C2T x fibers can be used as heaters. Notably, the nematic LC phase can be achieved in other MXenes (Mo2Ti2C3T x and Ti2CT x ) and in various organic solvents, suggesting the widespread LC behavior of MXene inks.