Characterization of aerosol plumes from singing and playing wind instruments associated with the risk of airborne virus transmission.

The exhalation of aerosols during musical performances or rehearsals posed a risk of airborne virus transmission in the COVID-19 pandemic. Previous research studied aerosol plumes by only focusing on one risk factor, either the source strength or convective transport capability. Furthermore, the source strength was characterized by the aerosol concentration and ignored the airflow rate needed for risk analysis in actual musical performances. This study characterizes aerosol plumes that account for both the source strength and convective transport capability by conducting experiments with 18 human subjects. The source strength was characterized by the source aerosol emission rate, defined as the source aerosol concentration multiplied by the source airflow rate (brass 383 particle/s, singing 408 particle/s, and woodwind 480 particle/s). The convective transport capability was characterized by the plume influence distance, defined as the sum of the horizontal jet length and horizontal instrument length (brass 0.6 m, singing 0.6 m and woodwind 0.8 m). Results indicate that woodwind instruments produced the highest risk with approximately 20% higher source aerosol emission rates and 30% higher plume influence distances compared with the average of the same risk indicators for singing and brass instruments. Interestingly, the clarinet performance produced moderate source aerosol concentrations at the instrument's bell, but had the highest source aerosol emission rates due to high source airflow rates. Flute performance generated plumes with the lowest source aerosol emission rates but the highest plume influence distances due to the highest source airflow rate. Notably, these comprehensive results show that the source airflow is a critical component of the risk of airborne disease transmission. The effectiveness of masking and bell covering in reducing aerosol transmission is due to the mitigation of both source aerosol concentrations and plume influence distances. This study also found a musician who generated approximately five times more source aerosol concentrations than those of the other musicians who played the same instrument. Despite voice and brass instruments producing measurably lower average risk, it is possible to have an individual musician produce aerosol plumes with high source strength, resulting in enhanced transmission risk; however, our sample size was too small to make generalizable conclusions regarding the broad musician population.

Evaluating SARS-CoV-2 airborne quanta transmission and exposure risk in a mechanically ventilated multizone office building.

The world has faced tremendous challenges during the COVID-19 pandemic since 2020, and effective clean air strategies that mitigate infectious risks indoors have become more essential. In this study, a novel approach based on the Wells-Riley model applied to a multizone building was proposed to simulate exposure to infectious doses in terms of "quanta". This modeling approach quantifies the relative benefits of different risk mitigation strategies so that their effectiveness could be compared. A case study for the US Department of Energy large office prototype building was conducted to illustrate the approach. The infectious risk propagation from the infection source throughout the building was evaluated. Different mitigation strategies were implemented, including increasing outdoor air ventilation rates and adding air-cleaning devices such as Minimum Efficiency Reporting Value (MERV) filters and portable air cleaners (PACs) with HEPA filters in-room/in-duct germicidal ultraviolet (GUV) lights, layering with wearing masks. Results showed that to keep the risk of the infection propagating low the best strategy without universal masking was the operation of in-room GUV or a large industrial-sized PAC; whereas with masking all strategies were acceptable. This study contributes to a better understanding of the airborne transmission risks in multizone, mechanically ventilated buildings and how to reduce infection risk from a public health perspective of different mitigation strategies.

Transmission of SARS-CoV-2 by inhalation of respiratory aerosol in the Skagit Valley Chorale superspreading event.

During the 2020 COVID-19 pandemic, an outbreak occurred following attendance of a symptomatic index case at a weekly rehearsal on 10 March of the Skagit Valley Chorale (SVC). After that rehearsal, 53 members of the SVC among 61 in attendance were confirmed or strongly suspected to have contracted COVID-19 and two died. Transmission by the aerosol route is likely; it appears unlikely that either fomite or ballistic droplet transmission could explain a substantial fraction of the cases. It is vital to identify features of cases such as this to better understand the factors that promote superspreading events. Based on a conditional assumption that transmission during this outbreak was dominated by inhalation of respiratory aerosol generated by one index case, we use the available evidence to infer the emission rate of aerosol infectious quanta. We explore how the risk of infection would vary with several influential factors: ventilation rate, duration of event, and deposition onto surfaces. The results indicate a best-estimate emission rate of 970 ± 390 quanta/h. Infection risk would be reduced by a factor of two by increasing the aerosol loss rate to 5 h-1 and shortening the event duration from 2.5 to 1 h.

Review and comparison of HVAC operation guidelines in different countries during the COVID-19 pandemic.

Various organizations and societies around the globe have issued guidelines in response to the coronavirus disease (COVID-19) and virus (SARS-CoV-2). In this paper, heating, ventilating, and air-conditioning-related guidelines or documents in several major countries and regions have been reviewed and compared, including those issued by the American Society of Heating Refrigerating and Air-Conditioning Engineers, the Federation of European Heating, Ventilation, and Air Conditioning Associations, the Society of Heating, Air-Conditioning and Sanitary Engineers of Japan, Architectural Society of China, and the Chinese Institute of Refrigeration. Most terms and suggestions in these guidelines are consistent with each other, although there are some conflicting details, reflecting the underlying uncertainty surrounding the transmission mechanism and characteristics of COVID-19 in buildings. All guidelines emphasize the importance of ventilation, but the specific ventilation rate that can eliminate the risk of transmission of airborne particulate matter has not been established. The most important countermeasure, commonly agreed countermeasures, the conflicting content from different guidelines, and further work have been summarized in this paper.

Time-Resolved Measurements of Indoor Chemical Emissions, Deposition, and Reactions in a University Art Museum.

A 6-week study was conducted at the University of Colorado Art Museum, during which volatile organic compounds (VOCs), carbon dioxide (CO2), ozone (O3), nitric oxide (NO), nitrogen dioxide (NO2), other trace gases, and submicron aerosol were measured continuously. These measurements were then analyzed using a box model to quantify the rates of major processes that transformed the composition of the air. VOC emission factors were quantified for museum occupants and their activities. The deposition of VOCs to surfaces was quantified across a range of VOC saturation vapor concentrations ( C*) and Henry's Law constants ( H) and determined to be a major sink for VOCs with C* < 108 µg m-3 and H > 102 M atm-1. The reaction rates of VOCs with O3, OH radicals, and nitrate (NO3) radicals were quantified, with unsaturated and saturated VOCs having oxidation lifetimes of >5 and >15 h, making deposition to surfaces and ventilation the dominant VOC sinks in the museum. O3 loss rates were quantified inside a museum gallery, where reactions with surfaces, NO, occupants, and NO2 accounted for 62%, 31%, 5%, and 2% of the O3 sink. The measured concentrations of acetic acid, formic acid, NO2, O3, particulate matter, sulfur dioxide, and total VOCs were below the guidelines for museums.

Budgets of Organic Carbon Composition and Oxidation in Indoor Air.

The chemical composition of indoor air at the University of Colorado, Boulder art museum was measured by a suite of gas- and particle-phase instruments. Over 80% of the total observed organic carbon (TOOC) mass (100 µg m-3) consisted of reduced compounds (carbon oxidation state, OSC < -0.5) with high volatility (log10 C* > 7) and low carbon number (nC < 6). The museum TOOC was compared to other indoor and outdoor locations, which increased according to the following trend: remote < rural ≤ urban < indoor ≤ megacity. The museum TOOC was comparable to a university classroom and 3× less than residential environments. Trends in the total reactive flux were remote < indoor < rural < urban < megacity. High volatile organic compound (VOC) concentrations compensated low oxidant concentrations indoors to result in an appreciable reactive flux. Total hydroxyl radical (OH), ozone (O3), nitrate radical (NO3), and chlorine atom (Cl) reactivities for each location followed a similar trend to TOOC. High human occupancy events increased all oxidant reactivities in the museum by 65-125%. The lifetimes of O3, NO3, OH, and Cl reactivities were 13 h, 15 h, 23 days, and 189 days, respectively, corresponding to over 88% of indoor VOC oxidant reactivity being consumed outdoors after ventilation.

Potential airborne pathogen transmission in a hospital with and without surge control ventilation system modifications.

To better understand the transport of airborne particulate matter (PM) in hospital environments when surge control strategies are implemented, tests were conducted in a recently decommissioned hospital during a one-week period. An aerosol was released within a patient room and concentrations measured in the room and hallway with and without surge control ventilation system modifications. The average hallway protection efficiencies were high (>98%) both for the baseline ventilation configuration and when the ventilation system was modified for whole floor negative pressure, indicating very little PM reached the hallway. During entry/exit events through the patient room door into the hallway, the average minimum hallway protection efficiencies were lower during the modified ventilation operation (93-94%) than for the baseline operation (98-99%). These lower hallway protection efficiencies may be explained by the 52% reduction in the outdoor air ventilation being supplied to the hallway during the modified operation mode. This suggests that patient room doors should remain closed to control PM movement into the hallway. In addition, if there is concern about airborne infection transmission, an anteroom may be used to further reduce the transport of particles from the patient rooms to the hallways of the ward.

The ecology of microscopic life in household dust.

We spend the majority of our lives indoors; yet, we currently lack a comprehensive understanding of how the microbial communities found in homes vary across broad geographical regions and what factors are most important in shaping the types of microorganisms found inside homes. Here, we investigated the fungal and bacterial communities found in settled dust collected from inside and outside approximately 1200 homes located across the continental US, homes that represent a broad range of home designs and span many climatic zones. Indoor and outdoor dust samples harboured distinct microbial communities, but these differences were larger for bacteria than for fungi with most indoor fungi originating outside the home. Indoor fungal communities and the distribution of potential allergens varied predictably across climate and geographical regions; where you live determines what fungi live with you inside your home. By contrast, bacterial communities in indoor dust were more strongly influenced by the number and types of occupants living in the homes. In particular, the female : male ratio and whether a house had pets had a significant influence on the types of bacteria found inside our homes highlighting that who you live with determines what bacteria are found inside your home.

Impacts of flood damage on airborne bacteria and fungi in homes after the 2013 Colorado Front Range flood.

Flood-damaged homes typically have elevated microbial loads, and their occupants have an increased incidence of allergies, asthma, and other respiratory ailments, yet the microbial communities in these homes remain under-studied. Using culture-independent approaches, we characterized bacterial and fungal communities in homes in Boulder, CO, USA 2-3 months after the historic September, 2013 flooding event. We collected passive air samples from basements in 50 homes (36 flood-damaged, 14 non-flooded), and we sequenced the bacterial 16S rRNA gene (V4-V5 region) and the fungal ITS1 region from these samples for community analyses. Quantitative PCR was used to estimate the abundances of bacteria and fungi in the passive air samples. Results indicate significant differences in bacterial and fungal community composition between flooded and non-flooded homes. Fungal abundances were estimated to be three times higher in flooded, relative to non-flooded homes, but there were no significant differences in bacterial abundances. Penicillium (fungi) and Pseudomonadaceae and Enterobacteriaceae (bacteria) were among the most abundant taxa in flooded homes. Our results suggest that bacterial and fungal communities continue to be affected by flooding, even after relative humidity has returned to baseline levels and remediation has removed any visible evidence of flood damage.

The short-term association of selected components of fine particulate matter and mortality in the Denver Aerosol Sources and Health (DASH) study.

BACKGROUND: Associations of short-term exposure to fine particulate matter (PM2.5) with daily mortality may be due to specific PM2.5 chemical components. Daily concentrations of PM2.5 components were measured over five years in Denver to investigate whether specific PM2.5 components are associated with daily mortality. METHODS: Daily counts of total and cause-specific deaths were obtained for the 5-county Denver metropolitan region from 2003 through 2007. Daily 24-hour concentrations of PM2.5, elemental carbon (EC), organic carbon (OC), sulfate and nitrate were measured at a central residential monitoring site. Using generalized additive models, we estimated relative risks (RRs) of daily death counts for daily PM2.5 and four PM2.5 component concentrations at single and distributed lags between the current and three previous days, while controlling for longer-term time trend and meteorology. RESULTS: RR of total non-accidental mortality for an inter-quartile increase of 4.55 µg/m(3) in PM2.5 distributed over 4 days was 1.012 (95 % confidence interval: 0.999, 1.025); RRs for EC and OC were larger (1.024 [1.005, 1.043] and 1.020 [1.000, 1.040] for 0.33 and 1.67 µg/m(3) increases, respectively) than those for sulfate and nitrate. We generally did not observe associations with cardiovascular and respiratory mortality except for associations with ischemic heart disease mortality at lags 3 and 0-3 depending on the component. In addition, there were associations with cancer mortality, particularly for EC and OC, possibly reflecting advanced deaths of a frail population. CONCLUSIONS: PM2.5 components possibly from combustion-related sources are more strongly associated with daily mortality than are secondary inorganic aerosols.

Industrial odor sources and air pollutant concentrations in Globeville, a Denver, Colorado neighborhood.

UNLABELLED: An odor of unknown origin described as a "tar" or "asphalt" smell has become unbearable for many of Globeville, CO, residents over the past few years. Residents report during odor events burning eyes and throat, headaches, skin irritation, and problems sleeping. This study was undertaken to identify the potential sources of the odor and the concentrations of air pollutants making up the odor by conducting meteorological correlations and sampling for a panel of volatile organic compounds (VOCs), sulfur gases, and polycyclic aromatic hydrocarbons (PAHs) in the neighborhood and near suspected sources. Wind speed and direction data collected every 1 min in the neighborhood indicate that when the odor is noticed, the community is directly downwind of a wood preservation facility and an asphalt roofing facility. Air samples collected during high-intensity odor events have shown concentrations of methylene chloride, hexane, toluene, naphthalene, dibenz[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3-cd]pyrene, each at least two times higher than background concentrations. Naphthalene and the other PAHs are known pollutants emitted from wood treatment processes, and are known to have a coal tar odor. Naphthalene was present in a sample collected directly adjacent to the Koppers facility and was not present in any background samples. Single-compound odor and health thresholds, however, were never surpassed. Given the technical and regulatory challenges of sampling odors and controlling emissions, it is recommended that Globeville residents and neighboring industry pursue a "good neighbor policy" to solve the odor issue. Specific offending industrial processes could be identified for which there exist cost-effective control technologies that would reduce exposure to odors and air toxics in Globeville. IMPLICATIONS: Meteorological correlations and samples of volatile organic compounds (VOCs), sulfur gases, and polycyclic aromatic hydrocarbons (PAHs) in the Globeville, CO, neighborhood and near suspected sources during odor events indicate potential industrial sources of a transient and noxious odor. Legislative approaches have proven unfruitful and no health or odor thresholds were typically violated. New approaches are warranted to address odor mixture effects in neighborhoods near industrial facilities.

Mandating indoor air quality for public buildings.

If some countries lead by example, standards may increasingly become normalized.

Positive matrix factorization of a 32-month series of daily PM2.5 speciation data with incorporation of temperature stratification.

This study presents source apportionment results for PM2.5 from applying positive matrix factorization (PMF) to a 32-month series of daily PM2.5 compositional data from Denver, CO, including concentrations of sulfate, nitrate, bulk elemental carbon (EC) and organic carbon (OC), and 51 organic molecular markers (OMMs). An optimum 8-factor solution was determined primarily based on the interpretability of the PMF results and rate of matching factors from bootstrapped PMF solutions with those from the base case solution. These eight factors were identified as inorganic ion, n-alkane, EC/sterane, light n-alkane/polycyclic aromatic hydrocarbon (PAH), medium alkane/alkanoic acid, PAH, winter/methoxyphenol and summer/odd n-alkane. The inorganic ion factor dominated the reconstructed PM2.5 mass (sulfate + nitrate + EC + OC) in cold periods (daily average temperature < 10 °C; 43.7% of reconstructed PM2.5 mass) whereas the summer/odd n-alkane factor dominated in hot periods (> 20 °C; 53.1%). The two factors had comparable relative contributions of 26.5% and 27.1% in warm periods with temperatures between 10 °C and 20 °C. Each of the seven factors resolved in a previous study (Dutton et al., 2010b) using a 1-year data set from the same location matches one factor from the current work based on comparing factor profiles. Six out of the seven matched pairs of factors are linked to similar source classes as suggested by the strong correlations between factor contributions (r = 0.89 - 0.98). Temperature-stratified source apportionment was conducted for three subsets of the data in the current study, corresponding to the cold, warm and hot periods mentioned above. The cold period (7-factor) solution exhibited a similar distribution of reconstructed PM2.5 mass as the full data set solution. The factor contributions of the warm period (7-factor) solution were well correlated with those from the full data set solution (r = 0.76 - 0.99). However, the reconstructed PM2.5 mass was distributed more to inorganic ion, n-alkane and medium alkane/alkanoic acid factors in the warm period solution than in the full data set solution. For the hot period (6-factor) solution, PM2.5 mass distribution was quite different from that of the full data set solution, as illustrated by regression slopes as low as 0.2 and as high as 4.8 of each matched pair of factors across the two solutions.

Errors in coarse particulate matter mass concentrations and spatiotemporal characteristics when using subtraction estimation methods.

In studies of coarse particulate matter (PM10-2.5), mass concentrations are often estimated through the subtraction of PM2.5 from collocated PM10 tapered element oscillating microbalance (TEOM) measurements. Though all field instruments have yet to be updated, the Filter Dynamic Measurement System (FDMS) was introduced to account for the loss of semivolatile material from heated TEOM filters. To assess errors in PM10-2.5 estimation when using the possible combinations of PM10 and PM2.5 TEOM units with and without FDMS, data from three monitoring sites of the Colorado Coarse Rural-Urban Sources and Health (CCRUSH) study were used to simulate four possible subtraction methods for estimating PM10-2.5 mass concentrations. Assuming all mass is accounted for using collocated TEOMs with FDMS, the three other subtraction methods were assessed for biases in absolute mass concentration, temporal variability, spatial correlation, and homogeneity. Results show collocated units without FDMS closely estimate actual PM10-2.5 mass and spatial characteristics due to the very low semivolatile PM10-2.5 concentrations in Colorado. Estimation using either a PM2.5 or PM10 monitor without FDMS introduced absolute biases of 2.4 microg/m3 (25%) to -2.3 microg/m3 (-24%), respectively. Such errors are directly related to the unmeasured semivolatile mass and alter measures of spatiotemporal variability and homogeneity, all of which have implications for the regulatory and epidemiology communities concerned about PM10-2.5. Two monitoring sites operated by the state of Colorado were considered for inclusion in the CCRUSH acute health effects study, but concentrations were biased due to sampling with an FDMS-equipped PM2.5 TEOM and PM10 TEOM not corrected for semivolatile mass loss. A regression-based model was developed for removing the error in these measurements by estimating the semivolatile concentration of PM2.5 from total PM2.5 concentrations. By estimating nonvolatile PM2.5 concentrations from this relationship, PM10-2.5 was calculated as the difference between nonvolatile PM10 and PM2.5 concentrations.

Correction to "Model Evaluation of Secondary Chemistry due to Disinfection of Indoor Air with Germicidal Ultraviolet Lamps".

[This corrects the article DOI: 10.1021/acs.estlett.2c00599.].

Positive matrix factorization of PM(2.5): comparison and implications of using different speciation data sets.

To evaluate the utility and consistency of different speciation data sets in source apportionment of PM(2.5), positive matrix factorization (PMF) coupled with a bootstrap technique for uncertainty assessment was applied to four different 1-year data sets composed of bulk species, bulk species and water-soluble elements (WSE), bulk species and organic molecular markers (OMM), and all species. The five factors resolved by using only the bulk species best reproduced the observed concentrations of PM(2.5) components. Combining WSE with bulk species as PMF inputs also produced five factors. Three of them were linked to soil, road dust, and processed dust, and together contributed 26.0% of reconstructed PM(2.5) mass. A 7-factor PMF solution was identified using speciated OMM and bulk species. The EC/sterane and summertime/selective aliphatic factors had the highest contributions to EC (39.0%) and OC (53.8%), respectively. The nine factors resolved by including all species as input data are consistent with those from the previous two solutions (WSE and bulk species, OMM and bulk species) in both factor profiles and contributions (r = 0.88-1.00). The comparisons across different solutions indicate that the selection of input data set may depend on the PM components or sources of interest for specific source-oriented health study.