RESUMEN
The aim of this in vivo study was to validate the DIAGNOdent laser fluorescence method and the International Caries Detection and Assessment System (ICDAS) for caries classification against the gold standard, histological examination, for detecting occlusal caries on permanent molars; the thresholds used were the outer enamel (D1), the inner enamel and outer third of the dentine (D2), and the inner two-thirds of the dentine (D3). Patients with non-impacted third molars (n = 43) were recruited from a university clinic. A trained examiner performed the examinations. After the teeth were extracted, the histological criterion was used to determine the severity of the lesions. Intra-examiner agreement (weighted kappa) for ICDAS was 0.60 and reliability (intraclass correlation coefficient) for DIAGNOdent was 0.968. The correlations with the histological reference were weak for DIAGNOdent (rs = 0.369) and moderate for ICDAS (rs = 0.515). The areas under the receiver-operating characteristics (ROC) curve at D1, D2, and D3 were 0.60, 0.69, and 0.91, respectively, for ICDAS and 0.55, 0.65, and 0.92, respectively, for DIAGNOdent. ICDAS and DIAGNOdent proved to be reproducible methods with similar performance in the detection of occlusal carious lesions in dentine. The ability of DIAGNOdent to detect initial enamel lesions was higher than that of ICDAS, but with low specificity. The usefulness of DIAGNOdent as an adjunct method for assessment of initial occlusal caries in permanent molars is questionable.
Asunto(s)
Caries Dental/diagnóstico , Esmalte Dental , Dentina , Fluorescencia , Humanos , Diente Molar , Reproducibilidad de los Resultados , Sensibilidad y EspecificidadRESUMEN
STATEMENT OF PROBLEM: Decementation is one of the most frequent causes of failure in the post-cement system. The bond strength in different parts of the canal may be influenced by technical and anatomic factors. PURPOSE: The purpose of this in vitro study was to assess the effects of anatomic root levels to reach the canal and different resin cements on the bond strength of fiberglass posts along the canal. MATERIAL AND METHODS: One hundred thirty-five roots of bovine teeth were endodontically treated, prepared with 15-mm-long post spaces and divided according to the anatomic root level: coronal (with 15-mm post space), middle (with 10-mm post space), and apical (with 5-mm post space). Fiberglass posts were luted with the cements (n=15): conventional resin cement with 3-step etch-and-rinse adhesive system (RelyX ARC/SBMP); self-adhesive resin cement (RelyX U200) and autopolymerizing resin cement with etch-and-rinse adhesive system (C&B/All-Bond 2). After 24 hours, specimens were sectioned and subjected to the push-out test. The maximum extrusion load was recorded (0.5 mm/minute, 200 N). Data were analyzed with analysis of variance (ANOVA) and the Tukey test (α=.05). Failure mode was analyzed by using multinomial logistic regression. RESULTS: There were no significant effects of resin cements (P>.05). The bond strength at apical third was higher when the canal was reached at the apical level than at the coronal level (P=.022). When each root level was directly reached, the coronal bond strength was lower than apical (P=.001) and middle (P=.021) for all cements. CONCLUSIONS: When the canal was reached at the coronal, medium, and apical levels, the bond strength of conventional, self-adhesive and autopolymerizing resin cements was lower in the coronal root third.
Asunto(s)
Recubrimiento Dental Adhesivo/métodos , Cavidad Pulpar/cirugía , Cementos de Resina/uso terapéutico , Cavidad Pulpar/anatomía & histología , Análisis del Estrés Dental , Humanos , Técnicas In Vitro , Técnica de Perno MuñónRESUMEN
BACKGROUND: Dental caries is the most prevalent oral disease in several Asian and Latin American countries. It is an infectious disease and different types of bacteria are involved in the process. Synthetic antimicrobials are used against this disease; however, many of these substances cause unwarranted undesirable effects like vomiting, diarrhea and tooth staining. Propolis, a resinous substance collected by honeybees, has been used to control the oral microbiota. So, the objective of this study was to develop and characterize sustained-release propolis-based chitosan varnish useful on dental cariogenic biofilm prevention, besides the in vitro antimicrobial activity. METHODS: Three formulations of propolis - based chitosan varnish (PCV) containing different concentrations (5%, 10% and 15%) were produced by dissolution of propolis with chitosan on hydro-alcoholic vehicle. Bovine teeth were used for testing adhesion of coatings and to observe the controlled release of propolis associated with varnish. It was characterized by infrared spectroscopy, scanning electron microscopy, casting time, diffusion test in vitro antimicrobial activity and controlled release. Minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) were tested for the main microorganisms involved in the cariogenic biofilm through the microdilution test in 96-well plates. RESULTS: The formulations presented a tooth surface adherence and were able to form films very fast on bovine tooth surface. Also, propolis-based chitosan varnishes have shown antimicrobial activity similar to or better than chlorhexidine varnish against all oral pathogen bacteria. All microorganisms were sensitive to propolis varnish and chitosan. MIC and MBC for microorganisms of cariogenic biofilme showed better results than chlorhexidine. Propolis active components were released for more than one week. CONCLUSION: All developed formulations turn them, 5%, 10% and 15% propolis content varnish, into products suitable for clinical application on dental caries prevention field, deserving clinical studies to confirm its in vivo activity.
Asunto(s)
Apiterapia , Bacterias/efectos de los fármacos , Biopelículas/efectos de los fármacos , Caries Dental/microbiología , Boca/microbiología , Própolis/farmacología , Diente , Adsorción , Animales , Antiinfecciosos/administración & dosificación , Antiinfecciosos/química , Antiinfecciosos/farmacología , Bacterias/crecimiento & desarrollo , Abejas , Bovinos , Quitosano/administración & dosificación , Quitosano/química , Quitosano/farmacología , Clorhexidina/farmacología , Preparaciones de Acción Retardada , Caries Dental/prevención & control , Humanos , Pruebas de Sensibilidad Microbiana , Pintura , Própolis/administración & dosificaciónRESUMEN
Sample preparation and imaging techniques for scanning electron microscopy (SEM) of dehydrated dental samples can hinder the structural analyses. This study qualitatively evaluated images obtained with two different protocols of SEM preparation and analysis to assess the dentine adhesive interface. The crown and root dentine of 12 bovine incisors were subjected to cementation with the resin cement RelyX U100 or RelyX ARC/SBMP (n = 6). After storage for 7 days in a moist environment at 37 ± 1°C, the dentine samples were dehydrated in an ascending alcohol series, and three specimens from each group were coated with gold or carbon and examined in a high-vacuum (JEOL JSM-6360LV, 10 kV) or low-vacuum (FEI Quanta 200F, 15-30 kV) microscope. Images were obtained at magnifications between 50 and 2,000×, but with different working distances. The use of high vacuum for carbon and gold coating and SEM visualization led to cracks in the samples. A small number of cracks can be described in the specimens subjected to the low-vacuum technique. The protocol for SEM imaging in low vacuum was considered more appropriate for preservation of the integrity of the evaluated structures.
Asunto(s)
Recubrimientos Dentinarios/química , Dentina/química , Microscopía Electrónica de Rastreo/métodos , Cementos de Resina/química , Animales , Bovinos , Dentina/metabolismo , Recubrimientos Dentinarios/metabolismo , Ensayo de Materiales , Cementos de Resina/metabolismoRESUMEN
The objective of this study was to evaluate the microtensile bond strength (µTBS) to dentin of two universal adhesive systems: Single Bond Universal (SBU) and Ambar Universal (AU), used in different adhesion strategies. MATERIALS AND METHOD: Thirty-six human teeth were prepared (n=6) and treated following different adhesive strategies: G1: SBU-etch-and-rinse, applied on dry dentin; G2: SBUetch- and-rinse, applied on moist dentin; G3: SBU-self-etching; G4: AU-etch-and-rinse, applied on dry dentin; G5: AU-etch-and-rinse, applied on moist dentin; G6: AU-self-etching. The specimens were submitted to µTBS test, failure analysis, and scanning electron microscopy (SEM). Data were analyzed with ANOVA and Tukey's tests (p<0.05). RESULTS: Microtensile bond strength was significantly lower in G1 than G2 and G3. AU adhesive performed worse than the SBU system, except in G5. Cohesive and mixed failures predominated in G1 and G2, while adhesive failures predominated in G3 and G5. CONCLUSIONS: Universal adhesives are an interesting innovation, but there are still doubts about their performance, mainly regarding the different protocols provided by the manufacturers. The conventional adhesive strategy on moist dentin demonstrated higher µTBS for both adhesives. The use of the selfetching strategy with the SBU showed promising results.
O objetivo deste estudo foi avaliar a resistência de união à microtração (µTBS) de dois sistemas adesivos universais: Single Bond Universal (SBU) e Ambar Universal (AU), utilizados em diferentes estratégias de adesão. Materiais e método: 36 dentes humanos foram preparados (n=6) e tratados seguindo diferentes estratégias adesivas: G1: SBU-condicionamento e enxágue, aplicado sobre dentina seca; G2: SBU-condicionamento e enxágue, aplicado sobre dentina úmida; G3: SBU-autocondicionante; G4: AU-condicionamento e enxágue, aplicado em dentina seca; G5: AU-condicionamento e enxágue, aplicado sobre dentina úmida; G6: AU-autocondicionante. Os espécimes foram submetidos ao teste de µTBS, análise de falhas e microscopia eletrônica de varredura (SEM). Os dados foram analisados com os testes ANOVA e Tukey (p<0,05). Resultados: A resistência de união à microtração de G1 foi significativamente menor que G2 e G3. O adesivo AU teve um desempenho pior que o sistema SBU, com exceção do G5. Falhas coesivas e mistas predominaram em G1 e G2 enquanto G3 e G5 apresentaram predominância de falhas adesivas. Conclusões: Os adesivos universais representam uma inovação interessante, mas ainda há dúvidas sobre seu desempenho, principalmente em relação aos diferentes protocolos fornecidos pelos fabricantes. A estratégia adesiva convencional em dentina úmida demonstrou maior µTBS para ambos os adesivos. O uso da estratégia autocondicionante com a SBU apresentou resultados promissores.
Asunto(s)
Recubrimiento Dental Adhesivo , Cementos Dentales , Humanos , Recubrimientos Dentinarios/química , Cementos de Resina/química , Recubrimiento Dental Adhesivo/métodos , Dentina , Resistencia a la Tracción , Ensayo de Materiales , Resinas Compuestas/químicaRESUMEN
ABSTRACT The objective of this study was to evaluate the microtensile bond strength (μTBS) to dentin of two universal adhesive systems: Single Bond Universal (SBU) and Ambar Universal , used in different adhesion strategies. Materials and Method: Thirty-six human teeth were prepared (n=6) and treated following different adhesive strategies: G1: SBU-etch-and-rinse, applied on dry dentin; G2: SBUetch- and-rinse, applied on moist dentin; G3: SBU-self-etching; G4: AU-etch-and-rinse, applied on dry dentin; G5: AU-etch-and-rinse, applied on moist dentin; G6: AU-self-etching. The specimens were submitted to μTBS test, failure analysis, and scanning electron microscopy (SEM). Data were analyzed with ANOVA and Tukey's tests (p<0.05). Results: Microtensile bond strength was significantly lower in G1 than G2 and G3. AU adhesive performed worse than the SBU system, except in G5. Cohesive and mixed failures predominated in G1 and G2, while adhesive failures predominated in G3 and G5. Conclusions: Universal adhesives are an interesting innovation, but there are still doubts about their performance, mainly regarding the different protocols provided by the manufacturers. The conventional adhesive strategy on moist dentin demonstrated higher μTBS for both adhesives. The use of the selfetching strategy with the SBU showed promising results.
RESUMO O objetivo deste estudo foi avaliar a resistência de união à microtração (μTBS) de dois sistemas adesivos universais: Single Bond Universal (SBU) e Ambar Universal , utilizados em diferentes estratégias de adesão. Materiais e método: 36 dentes humanos foram preparados (n=6) e tratados seguindo diferentes estratégias adesivas: G1: SBU-condicionamento e enxágue, aplicado sobre dentina seca; G2: SBU-condicionamento e enxágue, aplicado sobre dentina úmida; G3: SBU-autocondicionante; G4: AU-condicionamento e enxágue, aplicado em dentina seca; G5: AU-condicionamento e enxágue, aplicado sobre dentina úmida; G6: AU-autocondicionante. Os espécimes foram submetidos ao teste de μTBS, análise de falhas e microscopia eletrônica de varredura (SEM). Os dados foram analisados com os testes ANOVA e Tukey (p<0,05). Resultados: A resistência de união à microtração de G1 foi significativamente menor que G2 e G3. O adesivo AU teve um desempenho pior que o sistema SBU, com exceção do G5. Falhas coesivas e mistas predominaram em G1 e G2 enquanto G3 e G5 apresentaram predominância de falhas adesivas. Conclusões: Os adesivos universais representam uma inovação interessante, mas ainda há dúvidas sobre seu desempenho, principalmente em relação aos diferentes protocolos fornecidos pelos fabricantes. A estratégia adesiva convencional em dentina úmida demonstrou maior μTBS para ambos os adesivos. O uso da estratégia autocondicionante com a SBU apresentou resultados promissores.
RESUMEN
The aim of this study was to compare the areas of stress concentration in a three-dimensional (3D) premolar tooth model with anisotropic or isotropic enamel using the finite element method. A computed tomography was imported to an image processing program to create the tooth model which was exported to a 3D modeling program. The mechanical properties and loading conditions were prescribed in Abaqus. In order to evaluate stresses, axial and oblique loads were applied simulating realistic conditions. Compression stress was observed on the side of load application, and tensile stress was observed on the opposite side. Tensile stress was concentrated mainly in the cervical region and in the alveolar insertion bone. Although stress concentration analyses of the isotropic 3D models produced similar stress distribution results when compared to the anisotropic models, tensile stress values shown by anisotropic models were smaller than the isotropic models. Oblique loads resulted in higher values of tensile stresses, which concentrate mainly in the cervical area of the tooth and in the alveolar bone insertion. Anisotropic properties must be utilized in enamel stress evaluation in non-carious cervical lesions.
Asunto(s)
Diente Premolar/fisiología , Esmalte Dental/fisiología , Modelos Dentales , Anisotropía , Diente Premolar/diagnóstico por imagen , Fenómenos Biomecánicos , Esmalte Dental/diagnóstico por imagen , Análisis del Estrés Dental , Análisis de Elementos Finitos , Humanos , Imagenología Tridimensional , Estrés Mecánico , Tomografía Computarizada por Rayos XRESUMEN
BACKGROUND: Adhesive cementation is essential for the longevity of indirect esthetic restorations. However, polymerization shrinkage of resin cement generates stress, which may cause failures in the tooth-restoration interface. So, understanding of the biomechanics of resin cement is important for predicting the clinical behavior of an esthetic indirect restoration. AIMS: To analyze the stresses generated during polymerization shrinkage of self-curing resin cement in ceramic and in indirect resin (IR) restorations, using the finite-element method (FEM). SETTINGS AND DESIGN: Numerical study using the finite-element analysis. MATERIALS AND METHODS: A three-dimensional (3D) model of a second molar restored with ceramic or IR onlay restoration was designed. The polymerization shrinkage of self-curing resin cement was simulated in FEM software using an analogy between the thermal stress and the resulting contraction of the resin cement. The localization and values of tensile stresses in the dental structure, cement, and adhesive layer were identified. RESULTS: The location and value of the tensile stresses were similar for the two restorative materials. High tensile stresses were identified in the axiopulpal wall and angles of the tooth preparation, with the major stresses found in the cement located in the axiopulpal wall. CONCLUSIONS: The high stresses values and their concentration in the angles of the prepared tooth emphasize the importance of round angles and the use of cements with lower rates of shrinkage.
Asunto(s)
Restauración Dental Permanente/métodos , Análisis del Estrés Dental/métodos , Cementos de Resina/química , Óxido de Aluminio , Fenómenos Biomecánicos , Compuestos de Boro , Resinas Compuestas , Fracaso de la Restauración Dental , Análisis de Elementos Finitos , Ensayo de Materiales , Metacrilatos , Metilmetacrilatos , Modelos Dentales , PolimerizacionRESUMEN
Varnishes are preparations that differ in the polymeric matrix and therapeutical agents. In dentistry they are used to prevent caries. In this study we developed a propolis varnish, considering propolis properties against cariogenic bacteria. To a chitosan polymeric base (CHV) was added ethanolic propolis extract in different concentrations: PV1 (5%), PV2 (10%), and PV3 (15%). Antimicrobial activity was carried out against Streptococcus mutans (SM), Streptococcus sanguinis (SG), Streptococcus salivarius (SS), and Lactobacillus casei (LC) through agar diffusion method. The three propolis concentrations incorporated were effective in inhibiting the growth of all microorganisms, but without significant difference between the zones of inhibition observed. Cytotoxicity assay was done by MTT method. Data were analyzed by one-way ANOVA and Bonferroni test. None of the varnishes were cytotoxic, keeping 80% of viable cells, while CHV allowed cellular proliferation (120%). Sustained-release test was carried out by applying 40 µ L of each varnish in the buccal surface of bovine teeth and kept in an ethanol/water solution removed in regular times. According to the "independent model approach," the release profiles were distinct from each varnish and the most prolonged was PV3 (8 weeks). Varnish formulations had satisfactory antimicrobial activity against cariogenic bacteria and have a low cytotoxicity (<50%).
Asunto(s)
Cariogénicos/administración & dosificación , Caries Dental/tratamiento farmacológico , Própolis/administración & dosificación , Cariogénicos/química , Quitosano/administración & dosificación , Quitosano/química , Caries Dental/microbiología , Humanos , Lacticaseibacillus casei/efectos de los fármacos , Lacticaseibacillus casei/crecimiento & desarrollo , Própolis/química , Streptococcus mutans/efectos de los fármacos , Streptococcus mutans/crecimiento & desarrollo , Streptococcus sanguis/efectos de los fármacos , Streptococcus sanguis/crecimiento & desarrolloRESUMEN
OBJECTIVES: This study aimed to systematically review the scientific evidence for the association between noncarious cervical lesions (NCCL) and occlusal risk factors (ORF) [occlusal interferences in excursive movements; occlusal force; premature contacts; type of guidance; skid of centric occlusion to maximum intercuspidation] in adults. SOURCES: Pubmed, Web of Science, Cochrane, Lilacs, Clinical Trials, National Research Register and National Institute for Health were searched. STUDY SELECTION: From 1082 potentially eligible studies, 106 were selected for full text analysis. Two independent reviewers (Kappa=0.8; p<0.001) selected the studies, abstracted information and assessed quality based on standardised scales. Six cross-sectional, two case-controls and one clinical trial were included. Several occlusal variables were analysed among the studies, but there was no standardisation of the units used in the analysis of occlusal factors. The majority of studies did not find significant associations between NCCL and ORF. Three studies found associations between NCCL and some variables (occlusal contact area, right canine guidance, premature contacts in centric relation and working side) (p<0.05). The methodological quality varied across studies, and there was high heterogeneity among them. CONCLUSION: Current scientific evidence does not support an association between ORF and NCCL. Further prospective studies with standardised methods are vital to strengthen the evidence. CLINICAL SIGNIFICANCE: Understanding the risk factors for NCCL is important to control the causes and to help the dentist choose the best approach for the patient. The evidence does not support intervention to alter some occlusal factors for the prevention or control of the progression of NCCL.
Asunto(s)
Oclusión Dental , Cuello del Diente/patología , Desgaste de los Dientes/etiología , Fuerza de la Mordida , Relación Céntrica , Oclusión Dental Céntrica , Oclusión Dental Traumática/complicaciones , Humanos , Maloclusión/complicaciones , Factores de RiesgoRESUMEN
Active implant periapical lesion (IPL) is a rare lesion which has been reported as one of the causes of dental implant failures. Usually, an affected implant shows radiolucency in the apical area, while remaining clinically stable. IPL is often accompanied by symptoms of pain, swelling, tenderness, and fistulation. In this paper, we describe two cases of IPL with very unusual findings which led to implant failure. A large IPL associated with an inflammatory cyst in the anterior maxilla, and a mandibular IPL resulting in an extra-oral fistula are presented. The etiology and treatment approaches for IPL are discussed.