Micro-cone arrays enhance outcoupling efficiency in horticulture luminescent solar concentrators.

Luminescent solar concentrators (LSCs) have shown the ability to realize spectral conversion, which could tailor the solar spectrum to better match photosynthesis requirements. However, conventional LSCs are designed to trap, rather than extract, spectrally converted light. Here, we propose an effective method for improving outcoupling efficiency based on protruded and extruded micro-cone arrays patterned on the bottom surface of LSCs. Using Monte Carlo ray tracing, we estimate a maximum external quantum efficiency (EQE) of 37.73% for our horticulture LSC (HLSC), corresponding to 53.78% improvement relative to conventional, planar LSCs. Additionally, structured HLSCs provide diffuse light, which is beneficial for plant growth. Our micro-patterned surfaces provide a solution to light trapping in LSCs and a foundation for the practical application of HLSCs.

Fiber-optic hydrophone for detection of high-intensity ultrasound waves.

Fiber-optic hydrophones (FOHs) are widely used to detect high-intensity focused ultrasound (HIFU) fields. The most common type consists of an uncoated single-mode fiber with a perpendicularly cleaved end face. The main disadvantage of these hydrophones is their low signal-to-noise ratio (SNR). To increase the SNR, signal averaging is performed, but the associated increased acquisition times hinder ultrasound field scans. In this study, with a view to increasing SNR while withstanding HIFU pressures, the bare FOH paradigm is extended to include a partially reflective coating on the fiber end face. Here, a numerical model based on the general transfer-matrix method was implemented. Based on the simulation results, a single-layer, 172 nm TiO2-coated FOH was fabricated. The frequency range of the hydrophone was verified from 1 to 30 MHz. The SNR of the acoustic measurement with the coated sensor was 21 dB higher than that of the uncoated one. The coated sensor successfully withstood a peak positive pressure of 35 MPa for 6000 pulses.

Self-assembled porous polymer films for improved oxygen sensing.

Absolute oxygen sensors based on quenching of phosphorescence have been the subject of numerous studies for the monitoring of biological environments. Here, we used simple fabrication techniques with readily available polymers to obtain high performance phosphorescent films. Specifically, evaporation-based phase separation and the breath figure technique were used to induce porosity. The pore sizes ranged from ∼37 nm to ∼141 µm while the maximum average porosity achieved was ∼74%. The oxygen sensing properties were evaluated via a standarised calibration procedure with an optoelectronic setup in both transmission and reflection based configurations. When comparing non-porous and porous films, the highest improvements achieved were a factor of ∼7.9 in dynamic range and ∼7.3 in maximum sensitivity, followed by an improved linearity with a half-sensitivity point at 43% O2 V/V. Also, the recovery time was reduced by an order of magnitude in the high porosity film and all samples prepared were not affected by variations in the humidity of the surrounding environment. Despite the use of common polymers, the fabrication techniques employed led to the significant enhancement of oxygen sensing properties and elucidated the relation between porous film morphologies and sensing performance.

Spectroscopic Identification of Active Sites of Oxygen-Doped Carbon for Selective Oxygen Reduction to Hydrogen Peroxide.

The electrochemical synthesis of hydrogen peroxide (H2 O2 ) via a two-electron (2 e- ) oxygen reduction reaction (ORR) process provides a promising alternative to replace the energy-intensive anthraquinone process. Herein, we develop a facile template-protected strategy to synthesize a highly active quinone-rich porous carbon catalyst for H2 O2 electrochemical production. The optimized PCC900 material exhibits remarkable activity and selectivity, of which the onset potential reaches 0.83 V vs. reversible hydrogen electrode in 0.1 M KOH and the H2 O2 selectivity is over 95 % in a wide potential range. Comprehensive synchrotron-based near-edge X-ray absorption fine structure (NEXAFS) spectroscopy combined with electrocatalytic characterizations reveals the positive correlation between quinone content and 2 e- ORR performance. The effectiveness of chair-form quinone groups as the most efficient active sites is highlighted by the molecule-mimic strategy and theoretical analysis.

Delayed Lubricant Depletion of Slippery Liquid Infused Porous Surfaces Using Precision Nanostructures.

Slippery liquid infused porous surfaces (SLIPS) are an important class of repellent materials, comprising micro/nanotextures infused with a lubricating liquid. Unlike superhydrophobic surfaces, SLIPS do not rely on a stable air-liquid interface and thus can better manage low surface tension fluids, are less susceptible to damage under physical stress, and are able to self-heal. However, these collective properties are only efficient as long as the lubricant remains infused, which has proved challenging. We hypothesized that, in comparison to a nanohole and nanopillar morphology, the "hybrid" morphology of a hole within a nanopillar, namely a nanotube, would be able to retain and redistribute lubricant more effectively, owing to capillary forces trapping a reservoir of lubricant within the tube, while lubricant between tubes can facilitate redistribution to depleted areas. By virtue of recent fabrication advances in spacer defined intrinsic multiple patterning (SDIMP), we fabricated an array of silicon nanotubes and equivalent arrays of nanoholes and nanopillars (pitch, 560 nm; height, 2 µm). After infusing the nanostructures (prerendered hydrophobic) with lubricant Krytox 1525, we probed the lubricant stability under dynamic conditions and correlated the degree of the lubricant film discontinuity to changes in the contact angle hysteresis. As a proof of concept, the durability test, which involved consecutive deposition of droplets onto the surface amounting to 0.5 L, revealed 2-fold and 1.5-fold enhancements of lubricant retention in nanotubes in comparison to nanopillars and nanoholes, respectively, showing a clear trajectory for prolonging the lifetime of a slippery surface.

Precision-Microfabricated Fiber-Optic Probe for Intravascular Pressure and Temperature Sensing.

Small form-factor sensors are widely used in minimally invasive intravascular diagnostic procedures. Manufacturing complexities associated with miniaturizing current fiber-optic probes, particularly for multi-parameter sensing, severely constrain their adoption outside of niche fields. It is especially challenging to rapidly prototype and iterate upon sensor designs to optimize performance for medical devices. In this work, a novel technique to construct a microscale extrinsic fiber-optic sensor with a confined air cavity and sub-micron geometric resolution is presented. The confined air cavity is enclosed between a 3 µm thick pressure-sensitive distal diaphragm and a proximal temperature-sensitive plano-convex microlens segment unresponsive to changes in external pressure. Simultaneous pressure and temperature measurements are possible through optical interrogation via phase-resolved low-coherence interferometry (LCI). Upon characterization in a simulated intravascular environment, we find these sensors capable of detecting pressure changes down to 0.11 mmHg (in the range of 760 to 1060 mmHg) and temperature changes of 0.036 °C (in the range 34 to 50 °C). By virtue of these sensitivity values suited to intravascular physiological monitoring, and the scope of design flexibility enabled by the precision-fabricated photoresist microstructure, it is envisaged that this technique will enable construction of a wide range of fiber-optic sensors for guiding minimally invasive medical procedures.

Fluorine-Free Transparent Superhydrophobic Nanocomposite Coatings from Mesoporous Silica.

In recent decades, there has been a growing interest in the development of functional, fluorine-free superhydrophobic surfaces with improved adhesion for better applicability into real-world problems. Here, we compare two different methods, spin coating and aerosol-assisted chemical vapor deposition (AACVD), for the synthesis of transparent fluorine-free superhydrophobic coatings. The material was made from a nanocomposite of (3-aminopropyl)triethoxysilane (APTES) functional mesoporous silica nanoparticles and titanium cross-linked polydimethylsiloxane with particle concentrations between 9 to 50 wt %. The silane that was used to lower the surface energy consisted of a long hydrocarbon chain without fluorine groups to reduce the environmental impact of the composite coating. Both spin coating and AACVD resulted in the formation of superhydrophobic surfaces with advancing contact angles up to 168°, a hysteresis of 3°, and a transparency of 90% at 550 nm. AACVD has proven to produce more uniform coatings with concentrations as low as 9 wt %, reaching superhydrophobicity. The metal oxide cross-linking improves the adhesion of the coating to the glass. Overall, AACVD was the more optimal method to prepare superhydrophobic coatings compared to spin coating due to higher contact angles, adhesion, and scalability of the fabrication process.

Dynamically configurable, successively switchable multispectral plasmon-induced transparency.

Plasmon-induced transparency (PIT) in nanostructures has been intensively investigated; however, there are no known metasurface nanostructures that exhibit all optically tunable properties, where the number of transparency windows can be tuned successively and switched to off-state. In this Letter, we theoretically investigate and demonstrate a dynamically tunable, multichannel PIT at optical frequencies. The in-plane destructive interference between bright and dark dipolar resonances in coupled plasmonic nanobar topologies is exploited to produce a tunable PIT with unique characteristics. In particular, we demonstrate a sequential polarization-selective multispectral operation whereby the number of PIT channels can be varied successively from 3 to 0. The results provide a promising route for an active manipulation of PIT and show potential applications for multifunctional dynamic nanophotonics devices.

Impact of curvature on the optimal configuration of flexible luminescent solar concentrators.

Flexible luminescent solar concentrators (LSCs) could deliver integrated photovoltaics in all aspects of our lives, from architecture to wearable electronics. We present and experimentally verify a model for the optimization of the external optical efficiency of LSCs under varying degrees of curvature. We demonstrate differences between the optimization of flat and bent LSCs, showing that optimal fluorophore concentrations can differ by a factor of two.

Flexible and fluorophore-doped luminescent solar concentrators based on polydimethylsiloxane.

We demonstrate a simple and inexpensive method to fabricate flexible and fluorophore-doped luminescent solar concentrators (LSCs). Polydimethylsiloxane (PDMS) serves as a host material which additionally offers the potential to cast LSCs in arbitrary shapes. The laser dye Pyrromethene 567 is used as a prototype fluorophore, and it is shown that it has a high quantum yield of 93% over the concentration range investigated. The optical efficiency and loss channels of the flexible LSCs are investigated; it is also demonstrated that the efficiency remains high while bending the LSC which is essential for flexible LSCs to make an impact on solar energy.

Visible light communications: real time 10 Mb/s link with a low bandwidth polymer light-emitting diode.

This paper presents new experimental results on a polymer light-emitting diode based visible light communications system. For the first time we demonstrate a 10 Mb/s link based on the on-off keying data format with real time equalization on a field programmable gate array. The 10 Mb/s transmission speed is available at a bit error rate less than 4.6 × 10(-3), which is the limit for forward error correction. At a BER of 10(-6) a transmission speed of 7 Mb/s is readily achievable.

Optimizing Horticulture Luminescent Solar Concentrators via Enhanced Diffuse Emission Enabled by Micro-Cone Arrays.

Optimizing the photon spectrum for photosynthesis concurrently with improving crop yields presents an efficient and sustainable pathway to alleviate global food shortages. Luminescent solar concentrators (LSCs), consisting of transparent host matrices doped with fluorophores, show excellent promise to achieve the desired spectral tailoring. However, conventional LSCs are predominantly engineered for photon concentration, which results in a limited outcoupling efficiency of converted photons. Here, we introduce a scheme to implement LSCs into horticulture (HLSC) by enhancing light extraction. The symmetry of the device is disrupted by incorporating microcone arrays on the bottom surface to mitigate total internal reflection. Both Monte Carlo ray tracing simulations and experimental results have verified that the greatest enhancements in converted light extraction, relative to planar LSCs, are achieved using microcone arrays (base width 50 µm, aspect ratio 1.2) with extruded and protruded profiles (85.15 and 66.55% improvement, respectively). Angularly resolved transmission measurements show that the HLSC device exhibits a broad angular radiation distribution. This characteristic indicates that the HLSC device emits diffuse light, which is conducive to optimal plant growth.

Antimicrobial mechanisms of nanopatterned surfaces-a developing story.

Whilst it is now well recognized that some natural surfaces such as seemingly fragile insect wings possess extraordinary antimicrobial properties, a quest to engineer similar nanopatterned surfaces (NPSs) is ongoing. The stake is high as biofouling impacts critical infrastructure leading to massive social and economic burden with an antimicrobial resistance (AMR) issue at the forefront. AMR is one of the most imminent health challenges the world is facing today. Here, in the effort to find more sustainable solutions, the NPSs are proposed as highly promising technology as their antimicrobial activity arises from the topographical features, which could be realized on multiple material surfaces. To fully exploit these potentials however, it is crucial to mechanistically understand the underlying killing pathways. Thus far, several mechanisms have been proposed, yet they all have one thing in common. The antimicrobial process is initiated with bacteria contacting nanopatterns, which then imposes mechanical stress onto bacterial cell wall. Hence, the activity is called "mechano-bactericidal". From this point on, however, the suggested mechanisms start to diverge partly due to our limited understanding of force interactions at the interface. The aim of this mini review is to analyze the state-of-the-art in proposed killing mechanisms by categorizing them based on the characteristics of their driving force. We also highlight the current gaps and possible future directions in investigating the mechanisms, particularly by shifting towards quantification of forces at play and more elaborated biochemical assays, which can aid validating the current hypotheses.

Anal defecatory function in ulcerative colitis patients after total proctocolectomy and ileal pouch-anal anastomosis: a prospective cohort study.

BACKGROUND: Total proctocolectomy (TPC) followed by ileal pouch-anal anastomosis (IPAA) remains the only viable option whenever different treatment modalities fail in patients with ulcerative colitis (UC). OBJECTIVE: Prospective cohort pre/post study examining the anal defecatory function and competence in UC patients undergoing TPC plus IPAA using high-resolution anorectal manometry (HR-ARM). PATIENTS: Patients undergoing TPC and IPAA were enrolled in the study and subjected to HR-ARM prior to and 6 months after surgery. The anal resting, squeeze and push pressures were recorded, together with the rectal sensation and the rectal balloon expulsion test. The number of bowel movements, symptoms/signs related to fecal incontinence, as well as the IBDQ-32 quality of life questionnaires were documented during both HR-ARM visits. RESULTS: A total of 20 consecutive UC patients were recruited in our study. The mean (SD) number of bowel movements before the TPC plus IPAA was 10.1 (2.8), while the same number after the pouch surgery was 7.7 (3.1) [ P  = 0.01]. Symptoms or signs of fecal incontinence were noted in one of our patients prior to the operation; however, none of our patients reported any such symptoms after the pouch surgery. The median (IQR) IBDQ-32 questionnaire scores before and after surgery were 121.5 (13.5) and 142.5 (16.0) respectively. At the same time, the anorectal function remained intact since both the anal resting and squeeze pressures were not significantly changed. CONCLUSION: UC patients subjected to TPC-IPAA exhibit improved bowel movements and a normal anal defecatory function and competence post-surgery.

Nonwoven fiber meshes for oxygen sensing.

Accurate oxygen sensing and cost-effective fabrication are crucial for the adoption of wearable devices inside and outside the clinical setting. Here we introduce a simple strategy to create nonwoven polymeric fibrous mats for a notable contribution towards addressing this need. Although morphological manipulation of polymers for cell culture proliferation is commonplace, especially in the field of regenerative medicine, non-woven structures have not been used for oxygen sensing. We used an airbrush spraying, i.e. solution blowing, to obtain nonwoven fiber meshes embedded with a phosphorescent dye. The fibers serve as a polymer host for the phosphorescent dye and are shown to be non-cytotoxic. Different composite fibrous meshes were prepared and favorable mechanical and oxygen-sensing properties were demonstrated. A Young's modulus of 9.8 MPa was achieved and the maximum oxygen sensitivity improved by a factor of ∼2.9 compared to simple drop cast film. The fibers were also coated with silicone rubbers to produce mechanically robust sensing films. This reduced the sensing performance but improved flexibility and mechanical properties. Lastly, we are able to capture oxygen concentration maps via colorimetry using a smartphone camera, which should offer unique advantages in wider usage. Overall, the introduced composite fiber meshes show a potential to significantly improve cell cultures and healthcare monitoring via absolute oxygen sensing.

Efficiency and loss mechanisms of plasmonic Luminescent Solar Concentrators.

Using a hybrid nanoscale/macroscale model, we simulate the efficiency of a luminescent solar concentrator (LSC) which employs silver nanoparticles to enhance the dye absorption and scatter the incoming light. We show that the normalized optical efficiency can be increased from 10.4% for a single dye LSC to 32.6% for a plasmonic LSC with silver spheres immersed inside a thin dye layer. Most of the efficiency enhancement is due to scattering of the particles and not due to dye absorption/re-emission.

A bioinspired solution for spectrally selective thermochromic VO2 coated intelligent glazing.

We present a novel approach towards achieving high visible transmittance for vanadium dioxide (VO(2)) coated surfaces whilst maintaining the solar energy transmittance modulation required for smart-window applications. Our method deviates from conventional approaches and utilizes subwavelength surface structures, based upon those present on the eyeballs of moths, that are engineered to exhibit broadband, polarization insensitive and wide-angle antireflection properties. The moth-eye functionalised surface is expected to benefit from simultaneous super-hydrophobic properties that enable the window to self-clean. We develop a set of design rules for the moth-eye surface nanostructures and, following this, numerically optimize their dimensions using parameter search algorithms implemented through a series of Finite Difference Time Domain (FDTD) simulations. We select six high-performing cases for presentation, all of which have a periodicity of 130 nm and aspect ratios between 1.9 and 8.8. Based upon our calculations the selected cases modulate the solar energy transmittance by as much as 23.1% whilst maintaining high visible transmittance of up to 70.3%. The performance metrics of the windows presented in this paper are the highest calculated for VO(2) based smart-windows.

Glucose Oxidase Loading in Ordered Porous Aluminosilicates: Exploring the Potential of Surface Modification for Electrochemical Glucose Sensing.

Enzymatic electrochemical sensors have become the leading glucose detection technology due to their rapid response, affordability, portability, selectivity, and sensitivity. However, the performance of these sensors is highly dependent on the surface properties of the electrode material used to store glucose oxidase and its ability to retain enzymatic activity under variable environmental conditions. Mesoporous thin films have recently attracted considerable attention as promising candidates for enzyme storage and activity preservation due to their well-defined nanoarchitecture and tunable surface properties. Herein, we systematically compare pathways for the immobilization of glucose oxidase (GOx) and their effectiveness in electrochemical glucose sensing, following modification protocols that lead to the electrostatic attraction (amino functionalization), covalent bonding (aldehyde functionalization), and electrostatic repulsion (oxygen plasma treatment) of the ordered porous aluminosilicate-coated electrodes. By direct comparison using a quartz crystal microbalance, we demonstrate that glucose oxidase can be loaded in a nanoarchitecture with a pore size of ∼50 nm and pore interconnections of ∼35 nm using the native aluminosilicate surface, as well as after amino or aldehyde surface modification, while oxygen plasma exposure of the native surface inhibits glucose oxidase loading. Despite a variety of routes for enzyme loading, quantitative electrochemical glucose sensing between 0 and 20 mM was only possible when the porous surface was functionalized with amino groups, which we relate to the role of surface chemistry in accessing the underlying substrate. Our results highlight the impact of rational surface modification on electrochemical biosensing performance and demonstrate the potential of tailoring porous nanoarchitecture surfaces for biosensing applications.

A route to engineered high aspect-ratio silicon nanostructures through regenerative secondary mask lithography.

Silicon nanostructuring imparts unique material properties including antireflectivity, antifogging, anti-icing, self-cleaning, and/or antimicrobial activity. To tune these properties however, a good control over features' size and shape is essential. Here, a versatile fabrication process is presented to achieve tailored silicon nanostructures (thin/thick pillars, sharp/truncated/re-entrant cones), of pitch down to ∼50 nm, and high-aspect ratio (>10). The approach relies on pre-assembled block copolymer (BCP) micelles and their direct transfer into a glass hard mask of an arbitrary thickness, now enabled by our recently reported regenerative secondary mask lithography. During this pattern transfer, not only can the mask diameter be decreased but also uniquely increased, constituting the first method to achieve such tunability without necessitating a different molecular weight BCP. Consequently, the hard mask modulation (height, diameter) advances the flexibility in attainable inter-pillar spacing, aspect ratios, and re-entrant profiles (= glass on silicon). Combined with adjusted silicon etch conditions, the morphology of nanopatterns can be highly customized. The process control and scalability enable uniform patterning of a 6-inch wafer which is verified through cross-wafer excellent antireflectivity (<5%) and water-repellency (advancing contact angle 158°; hysteresis 1°). The implementation of this approach to silicon nanostructuring is envisioned to be far-reaching, facilitating fundamental studies and targeting applications spanning solar panels, antifogging/antibacterial surfaces, sensing, amongst many others.

Unique and universal dew-repellency of nanocones.

Surface structuring provides a broad range of water-repellent materials known for their ability to reflect millimetre-sized raindrops. Dispelling water at the considerably reduced scale of fog or dew, however, constitutes a significant challenge, owing to the comparable size of droplets and structures. Nonetheless, a surface comprising nanocones was recently reported to exhibit strong anti-fogging behaviour, unlike pillars of the same size. To elucidate the origin of these differences, we systematically compare families of nanotexture that transition from pillars to sharp cones. Through environmental electron microscopy and modelling, we show that microdroplets condensing on sharp cones adopt a highly non-adhesive state, even at radii as low as 1.5 µm, contrasting with the behaviour on pillars where pinning results in impedance of droplet ejection. We establish the antifogging abilities to be universal over the range of our cone geometries, which speaks to the unique character of the nanocone geometry to repel dew. Truncated cones are finally shown to provide both pinning and a high degree of hydrophobicity, opposing characteristics that lead to a different, yet efficient, mechanism of dew ejection that relies on multiple coalescences.