Multimodal Capturing of Polysulfides by Phosphorus-Doped Carbon Composites for Flexible High-Energy-Density Lithium-Sulfur Batteries.

The widespread adoption of Li-ion batteries is currently limited by their unstable electrochemical performance and high flammability under mechanical deformation conditions and a relatively low energy density. Herein, high-energy-density lithium-sulfur (Li-S) batteries are developed for applications in next-generation flexible electronics and electric vehicles with long cruising distances. Freestanding high-S-loading carbon nanotubes cathodes are assembled with a phosphorus (P)-doped carbon interlayer coated on commercial separators. Strategies for the active materials and structural design of both the electrodes and separators are highly efficient for immobilizing the lithium polysulfides via multimodal capturing effects; they significantly improve the electrochemical performance in terms of the redox kinetics and cycling stability. The foldable Li-S cells show stable specific capacities of 850 mAh g-1 over 100 cycles, achieving high gravimetric and volumetric energy densities of 387 Wh kgcell -1 and 395 Wh Lcell -1 , respectively. The Li-S cells show highly durable mechanical flexibilities under severe deformation conditions without short circuit or failure. Finally, the Li-S battery is explored as a light-weight and flexible energy storage device aboard airplane drones to ensure at least fivefold longer flight times than traditional Li-ion batteries. Nanocarbon-based S cathodes and P-doped carbon interlayers offer a promising solution for commercializing rechargeable Li-S batteries.

Rectification in Molecular Tunneling Junctions Based on Alkanethiolates with Bipyridine-Metal Complexes.

This paper addresses the mechanism for rectification in molecular tunneling junctions based on alkanethiolates terminated by a bipyridine group complexed with a metal ion, that is, having the structure AuTS-S(CH2)11BIPY-MCl2 (where M = Co or Cu) with a eutectic indium-gallium alloy top contact (EGaIn, 75.5% Ga 24.5% In). Here, AuTS-S(CH2)11BIPY is a self-assembled monolayer (SAM) of an alkanethiolate with 4-methyl-2,2'-bipyridine (BIPY) head groups, on template-stripped gold (AuTS). When the SAM is exposed to cobalt(II) chloride, SAMs of the form AuTS-S(CH2)11BIPY-CoCl2 rectify current with a rectification ratio of r+ = 82.0 at ±1.0 V. The rectification, however, disappears (r+ = 1.0) when the SAM is exposed to copper(II) chloride instead of cobalt. We draw the following conclusions from our experimental results: (i) AuTS-S(CH2)11BIPY-CoCl2 junctions rectify current because only at positive bias (+1.0 V) is there an accessible molecular orbital (the LUMO) on the BIPY-CoCl2 moiety, while at negative bias (-1.0 V), neither the energy level of the HOMO or the LUMO lies between the Fermi levels of the electrodes. (ii) AuTS-S(CH2)11BIPY-CuCl2 junctions do not rectify current because there is an accessible molecular orbital on the BIPY-CuCl2 moiety at both negative and positive bias (the HOMO is accessible at negative bias, and the LUMO is accessible at positive bias). The difference in accessibility of the HOMO levels at -1.0 V causes charge transfer-at negative bias-to take place via Fowler-Nordheim tunneling in BIPY-CoCl2 junctions, and via direct tunneling in BIPY-CuCl2 junctions. This difference in tunneling mechanism at negative bias is the origin of the difference in rectification ratio between BIPY-CoCl2 and BIPY-CuCl2 junctions.

Conformation, and Charge Tunneling through Molecules in SAMs.

This paper demonstrates that the molecular conformation (in addition to the composition and structure) of molecules making up self-assembled monolayers (SAMs) influences the rates of charge tunneling (CT) through them, in molecular junctions of the form AuTS/S(CH2)2CONR1R2//Ga2O3/EGaIn, where R1 and R2 are alkyl chains of different length. The lengths of chains R1 and R2 were selected to influence the conformations and conformational homogeneity of the molecules in the monolayer. The conformations of the molecules influence the thickness of the monolayer (i.e. tunneling barrier width) and their rectification ratios at ±1.0 V. When R1 = H, the molecules are well ordered and exist predominantly in trans-extended conformations. When R1 is an alkyl group (e.g., R1 ≠ H), however, their conformations can no longer be all-trans-extended, and the molecules adopt more gauche dihedral angles. This change in the type of conformation decreases the conformational order and influences the rates of tunneling. When R1 = R2, the rates of CT decrease (up to 6.3×), relative to rates of CT observed through SAMs having the same total chain lengths, or thicknesses, when R1 = H. When R1 ≠ H ≠ R2, there is a weaker correlation (relative to that when R1 = H or R1 = R2) between current density and chain length or monolayer thickness, and in some cases the rates of CT through SAMs made from molecules with different R2 groups are different, even when the thicknesses of the SAMs (as determined by XPS) are the same. These results indicate that the thickness of a monolayer composed of insulating, amide-containing alkanethiols does not solely determine the rate of CT, and rates of charge tunneling are influenced by the conformation of the molecules making up the junction.

Characterizing Chelation at Surfaces by Charge Tunneling.

This paper describes a surface analysis technique that uses the "EGaIn junction" to measure tunneling current densities (J(V), amps/cm2) through self-assembled monolayers (SAMs) terminated in a chelating group and incorporating different transition metal ions. Comparisons of J(V) measurements between bare chelating groups and chelates are used to characterize the composition of the SAM and infer the dissociation constant (Kd, mol/L), as well as kinetic rate constants (koff, L/mol·s; kon, 1/s) of the reversible chelate-metal reaction. To demonstrate the concept, SAMs of 11-(4-methyl-2,2'-bipyrid-4'-yl (bpy))undecanethiol (HS(CH2)11bpy) were incubated within ethanol solutions of metal salts. After rinsing and drying the surface, measurements of current as a function of incubation time and concentration in solution are used to infer koff, kon, and Kd. X-ray photoelectron spectroscopy (XPS) provides an independent measure of surface composition to confirm inferences from J(V) measurements. Our experiments establish that (i) bound metal ions are stable to the rinsing step as long as the rinsing time, τrinse ≪ 1koff; (ii) the bound metal ions increase the current density at the negative bias and reduce the rectification observed with free bpy terminal groups; (iii) the current density as a function of the concentration of metal ions in solution follows a sigmoidal curve; and (iv) the values of Kd measured using J(V) are comparable to those measured using XPS, but larger than those measured in solution. The EGaIn junction, thus, provides a new tool for the analysis of the composition of the surfaces that undergo reversible chemical reactions with species in solution.

Verification of Carrier Concentration-Dependent Behavior in Water-Infiltration-Induced Electricity Generation by Ionovoltaic Effect.

Water-infiltration-induced power generation has the renewable characteristic of generating electrical energy from ambient water. Importantly, it is found that the carrier concentration in semiconductor constituting the energy generator seriously affect the electricity generation. Nevertheless, few studies are conducted on the influence of semiconductor carrier concentration, a crucial factor on electricity generation. Due to this, understanding of the energy harvesting mechanism is still insufficient. Herein, the semiconductor carrier concentration-dependent behavior in water-infiltration-induced electricity generation and the energy harvesting mechanism by ionovoltaic effect are comprehensively verified. A clue to enhance the electric power generation efficiency is also proposed. When 20 µL of water (NaCl, 0.1 m) infiltrates into a porous CuO nanowires film (PCNF), electric power of ≈0.5 V and ≈1 µA are produced for 25 min. Moreover, the PCNF shows good practicability by generating electricity using various ambient water, turning on LEDs, and being fabricated as a curved one.

The effect of surface energy characterized functional groups of self-assembled monolayers for enhancing the electrical stability of oxide semiconductor thin film transistors.

The exact direction of the surface energy characterized functional groups of self-assembled monolayers (SAMs) is proposed for achieving enhanced electrical stability of indium gallium zinc oxide (IGZO) semiconductor thin film transistors (TFTs). The SAM treatment, particularly with the SAM functional group having lower surface energy, makes it difficult to adsorb oxygen molecules difficult onto IGZO. Such an effect greatly improves the positive bias stability (PBS) and clockwise hysteresis stability. For NH2 and CF3 functional groups, SAMs with surface energies of 49.4 mJ m-2 and 23.5 mJ m-2, respectively, improved the IGZO TFT PBS from 2.47 V to 0.32 V after the SAM treatment and the IGZO TFT clockwise hysteresis was also enhanced from 0.23 V to 0.11 V without any deterioration of TFT characteristics. Employing lower surface energy functional groups to the SAM, of the same head and body groups, passivates and protects the IGZO backchannel region from oxygen molecules in the atmosphere. Consequently, the enhanced electrical stability of IGZO TFTs can be achieved by the simple and economic SAM treatment.

The effect of Surface energy characterized functional group of self-assembled monolayer for enhancing electrical stability of oxide semiconductor thin film transistor.

The exact direction, of the surface energy characterized functional group of self-assembled monolayer (SAM), is proposed for achieving the enhanced electrical stability of indium gallium zinc oxide (IGZO) semiconductor thin film transistor (TFT). The SAM treatment, particularly at the SAM functional group having lower surface energy, makes oxygen molecules difficult to be adsorbed onto IGZO. And such an effect much improves positive bias stability (PBS) and clockwise hysteresis stability to the same tendency. For NH2 and CF3 functional group SAMs with surface energies of 49.4 mJ/m2 and 23.5 mJ/m2, respectively, the IGZO TFT PBS was improved from 2.47 V to 0.32 V after the SAM treatment and the IGZO TFT clockwise hysteresis was also enhanced from 0.23 V to 0.11 V without any deterioration of TFT characteristics. Employing lower surface energy functional group to the SAM, of same head group and body group, does passivate and protect the IGZO backchannel region from oxygen molecules in the atmosphere. Consequently, the enhanced electrical stability of IGZO TFT can be achieved by the simple and economic SAM treatment.

Dipole-Induced Rectification Across AgTS/SAM//Ga2O3/EGaIn Junctions.

This Article describes the relationship between molecular structure, and the rectification of tunneling current, in tunneling junctions based on self-assembled monolayers (SAMs). Molecular dipoles from simple organic functional groups (amide, urea, and thiourea) were introduced into junctions with the structure AgTS/S(CH2) nR(CH2) mCH3//Ga2O3/EGaIn. Here, R is an n-alkyl fragment (-CH2-)2 or 3, an amide group (either -CONH- or -NHCO-), a urea group (-NHCONH-), or a thiourea group (-NHCSNH-). The amide, urea, or thiourea groups introduce a localized electric dipole moment into the SAM and change the polarizability of that section of the SAM, but do not produce large, electronically delocalized groups or change other aspects of the tunneling barrier. This local change in electronic properties correlates with a statistically significant, but not large, rectification of current ( r+) at ±1.0 V (up to r+ ≈ 20). The results of this work demonstrate that the simplest form of rectification of current at ±1.0 V, in EGaIn junctions, is an interfacial effect, and is caused by a change in the work function of the SAM-modified silver electrode due to the proximity of the dipole associated with the amide (or related) group, and not to a change in the width or mean height of the tunneling barrier.

Graphitic Hollow Nanocarbon as a Promising Conducting Agent for Solid-State Lithium Batteries.

All-solid-state batteries (ASSBs) have lately received enormous attention for electric vehicle applications because of their exceptional stability by engaging all-solidified cell components. However, there are many formidable hurdles such as low ionic conductivity, interface instability, and difficulty in the manufacturing process, for its practical use. Recently, carbon, one of the representative conducting agents, turns out to largely participate in side reactions with the solid electrolyte, which finally leads to the formation of insulating side products at the interface. Although the battery community mentioned that parasitic reactions are presumably attributed to carbon itself or the generation of electronic conducting paths lowering the kinetic barrier for reactions, the underlying origin for such reactions as well as appropriate solutions have not been provided yet. In this study, for the first time, it is verified that the functional group on carbon is an origin for causing negative effects on interfacial stability and a graphitized hollow nanocarbon as a promising solution for improving-electrochemical performance is introduced. This work offers an invaluable lesson that a relatively minor part, such as a conducting agent, in ASSBs sometimes gives more positive impact on improving electrochemical performance than huge efforts for resolving other parts.

Ion Specificity on Electric Energy Generated by Flowing Water Droplets.

The development of energy-conversion devices using water movement has actively progressed. Ionovoltaic devices, which are driven by ion dynamics, show ion specificity by which different ions with identical charges show different output performance. However, the ion specificity remains poorly understood because the influence of the ion species on generated electric signals is not elucidated. The ion specificity in electric signals induced by flowing water droplet was investigated in terms of its relationship with the potential profile across the solid-liquid interface.

Identification of Droplet-Flow-Induced Electric Energy on Electrolyte-Insulator-Semiconductor Structure.

Recently, various energy transducers driven by the relative motion of solids and liquids have been demonstrated. However, in relation to the energy transducer, a proper understanding of the dynamic behavior of ions remains unclear. Moreover, the energy density is low for practical usage mainly due to structural limitations, a lack of material development stemming from the currently poor understanding of the mechanisms, and the intermittently generated electricity given the characteristics of the water motion (pulsed signals). Here, we verify a hypothesis pertaining to the ion dynamics which govern the operation mechanism of the transducer. In addition, we demonstrate enhanced energy transducer to convert the mechanical energy of flowing water droplets into continuous electrical energy using an electrolyte-insulator-semiconductor structure as a device structure. The output power per droplet mass and the ratio of generated electric energy to the kinetic energy of water drops are 0.149v2 mW·g-1·m-2·s2 and 29.8%, respectively, where v is the speed of the water droplet.

User-interactive electronic skin for instantaneous pressure visualization.

Electronic skin (e-skin) presents a network of mechanically flexible sensors that can conformally wrap irregular surfaces and spatially map and quantify various stimuli. Previous works on e-skin have focused on the optimization of pressure sensors interfaced with an electronic readout, whereas user interfaces based on a human-readable output were not explored. Here, we report the first user-interactive e-skin that not only spatially maps the applied pressure but also provides an instantaneous visual response through a built-in active-matrix organic light-emitting diode display with red, green and blue pixels. In this system, organic light-emitting diodes (OLEDs) are turned on locally where the surface is touched, and the intensity of the emitted light quantifies the magnitude of the applied pressure. This work represents a system-on-plastic demonstration where three distinct electronic components--thin-film transistor, pressure sensor and OLED arrays--are monolithically integrated over large areas on a single plastic substrate. The reported e-skin may find a wide range of applications in interactive input/control devices, smart wallpapers, robotics and medical/health monitoring devices.

Change of joint line convergence angle and other coronal alignments after total hip arthroplasty.

BACKGROUND: The purpose of this study was to determine the unloading effect of total hip arthroplasty (THA) on the ipsilateral knee joint through the joint line convergence angle (JLCA) change and determine the changes in other coronal radiographic parameters after THA, and evaluate the sensitivity of JLCA. PATIENTS AND METHODS: We retrospectively assessed 70 patients who underwent unilateral THA. Hip parameters such as neck shaft angle (NSA), neck length, and femoral offset and coronal alignment parameters of the lower extremity such as hip-knee-ankle angle (HKA), femur length, mechanical lateral distal femoral angle (mLDFA), JLCA, medial proximal tibial angle (MPTA), lateral distal tibial angle (LDTA), and plafond talus angle (PTA) were measured in the operative and non-operative sides. We compared all hip and coronal alignment parameters between before and 1 year after THA, and the amount of standardized changes (Δ) between all hip and coronal alignment parameters on the operative side, respectively. RESULTS: All mean hip and coronal alignment parameters on the operative side changed significantly 1-year after THA; however, those on the non-operative side did not. On the operative side, mean JLCA and PTA changed in the direction of closing the joint lateral space, from 1.81° and 0.47° to 1.22° and 0.11°, respectively (p<0.001 and 0.046, respectively). Mean NSA, HKA, and mLDFA changed in the valgus direction, from 129.39°, 2.62°, and 86.69° to 133.54°, 1.53°, and 85.91°, respectively (p<0.001). Mean femoral offset, neck length, and femur length increased from 36.45mm, 47.83mm, and 429.20mm to 39.85mm, 55.06mm, and 436.33mm, respectively (p<0.001). Mean MPTA and LDTA increased from 85.43° and 87.50° to 86.73° and 90.38, respectively (p<0.001). JLCA was more vulnerable to change than HKA, femur length, mLDFA, MPTA, and PTA (p<0.05). DISCUSSION: JLCA change on the operative side was more sensitive than changes of other coronal alignments after THA. According to the cohort, THA might have an unloading effect on the medial compartment of the knee joint. LEVEL OF EVIDENCE: IV; retrospective case-control and cohort studies.

Data and videos for the comparison of thermal propagation and cycle performance of multiple lithium-ion batteries in air and insulating oil.

The propagation test of lithium-ion battery pack was conducted in an environment of air and insulating oil. The test results showed the difference in the phenomenon in which fire propagation to surrounding cells, when a cell composing a battery pack is thermal runaway in two environments. The temperature of the cells in the battery pack was measured during propagation test. A cycle test was also conducted to check whether there was an abnormality in cell performance immersed in insulating oil. The residual capacity and internal resistance, insulation resistance data of the cell are presented in the two environments.

Postoperative stability after setback of sagittal split ramus osteotomy: a comparison of three techniques.

PURPOSE: The aim of the present study was to evaluate the postoperative stability after bilateral sagittal split ramus osteotomy (BSSRO) for the treatment of mandibular prognathism, in addition to a posterior ostectomy of the distal segment and mandibular angle resection. PATIENTS AND METHODS: The present retrospective study included patients with mandibular prognathism who were treated with BSSRO at Kangdong Sacred Heart Hospital from July 2007 to July 2011. We assessed the linear changes in the chin position in 17 patients with BSSRO only (control group), 10 with BSSRO and posterior ostectomy of the distal segment (experimental group 1), and 13 with BSSRO and mandibular angle resection (experimental group 2). A cephalogram was taken 2 weeks before surgery and 1 day and 2 months postoperatively. Differences among the groups were determined using 1-way analysis of variance. RESULTS: The demographic and surgical variables were similar among the groups. With regard to the changes observed 1 day to 2 months postoperatively, no statistically significant differences were found; however, the proportion of patients who had highly significant changes (>4 mm) was different. Point B moved forward and upward more than 4 mm in approximately 18% and 12% of patients, respectively, in the control group. However, such movement was not observed in any patient in the experimental group. CONCLUSIONS: Less postoperative instability was present in the experimental groups than in the control group. This might have resulted from the reduced tension in the pterygomasseteric sling and the minimized interference between the bony segments. Therefore, improved stability can be obtained regardless of the type of additional procedures.

Facile one-pot synthesis of biomass-derived activated carbon as an interlayer material for a BAC/PE/Al2O3 dual coated separator in Li-S batteries.

Lithium-sulfur batteries (LSB) are an attractive alternative electrochemical energy storage device compared to conventional lithium-ion batteries due to their higher theoretical capacity and energy density. Despite these advantages, it is still difficult to commercialize LSB because of poor electrochemical performance caused by the dissolution of soluble lithium polysulfides (LiPS). To solve these critical issues, a multi-functional separator was prepared using biomass-derived activated carbon (BAC) and a ceramic layer on the polyethylene (PE) separator. For this purpose, BAC was synthesized by a facile one-pot synthesis method by a specifically designed furnace using various forms of milk waste. The multi-functional separator suppresses the effect of LiPS dissolution and increases the Li+ diffusion kinetics. BAC was able to absorb the LiPS shuttle, as confirmed by UV-vis measurements and X-ray photoelectron spectroscopy (XPS). LSB cells assembled using this multi-functional separator show a higher discharge capacity of 1092.5 mA h g-1 at 0.1 C-rate, while commercial PE separators deliver a specific capacity of 811.8 mA h g-1. These novel separators were also able to suppress lithium dendrites during cycling. This work offers a novel and simple approach for streamlining the synthesis process of BAC and applying it to LSB, aiding in the development of sustainable energy sources.

Comparative Features of Calretinin, Calbindin and Parvalbumin Expressing Interneurons in Mouse and Monkey Primary Visual and Frontal Cortices.

Much is known about differences in pyramidal cells across cortical areas and species, but studies of interneurons have focused on comparisons within single cortical areas and/or species. Here we quantified the distribution and somato-dendritic morphology of interneurons expressing one or more of the calcium binding proteins (CaBPs) calretinin (CR), calbindin (CB) and/or parvalbumin (PV) in mouse ( Mus musculus ) versus rhesus monkey ( Macaca mulatta ) in two functionally and cytoarchitectonically distinct regions- the primary visual and frontal cortical areas. The density, laminar distribution and morphology of interneurons were assessed in serial brain sections using immunofluorescent multi-labeling, stereological counting and 3D reconstructions. There were significantly higher densities of CB+ and PV+ neurons in visual compared to frontal areas in both species. The main species difference was the significantly greater density and proportion of CR+ interneurons and lower extent of CaBP co-expression in monkey compared to mouse cortices. Cluster analyses revealed that the somato-dendritic morphology of layer 2-3 inhibitory interneurons is more dependent on CaBP expression than on species and area. Only modest effects of species were observed for CB+ and PV+ interneuron morphologies, while CR+ neurons showed no difference. By contrast to pyramidal cells which show highly distinctive area- and species-specific features, here we found more subtle differences in the distribution and features of interneurons across areas and species. These data yield insight into how nuanced differences in the population organization and properties of neurons may underlie specializations in cortical regions to confer species and area-specific functional capacities. Key Points: Somato-dendritic morphology of distinct interneurons did not substantially scale and vary across areas and species- differences were mainly dependent on CaBP expression.Cortical diversity in inhibitory function across areas and species is thus likely to be derived from differential laminar distribution and densities of distinct interneuron subclasses.In contrast to pyramidal cells which differ widely in distribution and morphology across areas and species, the features of interneurons appears to be relatively more conserved across areas and species.

Comparative features of calretinin, calbindin, and parvalbumin expressing interneurons in mouse and monkey primary visual and frontal cortices.

Fundamental differences in excitatory pyramidal cells across cortical areas and species highlight the implausibility of extrapolation from mouse to primate neurons and cortical networks. Far less is known about comparative regional and species-specific features of neurochemically distinct cortical inhibitory interneurons. Here, we quantified the density, laminar distribution, and somatodendritic morphology of inhibitory interneurons expressing one or more of the calcium-binding proteins (CaBPs) (calretinin [CR], calbindin [CB], and/or parvalbumin [PV]) in mouse (Mus musculus) versus rhesus monkey (Macaca mulatta) in two functionally and cytoarchitectonically distinct regions-the primary visual and frontal cortical areas-using immunofluorescent multilabeling, stereological counting, and 3D reconstructions. There were significantly higher densities of CB+ and PV+ neurons in visual compared to frontal areas in both species. The main species difference was the significantly greater density and proportion of CR+ interneurons and lower extent of CaBP coexpression in monkey compared to mouse cortices. Cluster analyses revealed that the somatodendritic morphology of layer 2-3 inhibitory interneurons is more dependent on CaBP expression than on species and area. Only modest effects of species were observed for CB+ and PV+ interneuron morphologies, while CR+ neurons showed no difference. By contrast to pyramidal cells that show highly distinctive area- and species-specific features, here we found more subtle differences in the distribution and features of interneurons across areas and species. These data yield insight into how nuanced differences in the population organization and properties of neurons may underlie specializations in cortical regions to confer species- and area-specific functional capacities.

Charge Transport Measured Using the EGaIn Junction through Self-Assembled Monolayers Immersed in Organic Liquids.

This paper describes measurements of charge transport by tunneling through molecular junctions comprising a self-assembled monolayer (SAM) supported by a template-stripped metal bottom electrode (MTS), which has been immersed in an organic liquid and contacted by a conical Ga2O3/EGaIn top electrode. These junctions formed in organic liquids are robust; they show stabilities and yields similar to those formed in air. We formed junctions under seven external environments: (I) air, (II) perfluorocarbons, (III) linear hydrocarbons, (IV) cyclic hydrocarbons, (V) aromatic compounds, (VI) large, irregularly shaped hydrocarbons, and (VII) dimethyl siloxanes. Several different lengths of SAMs of n-alkanethiolates, S(CH2)n-1CH3 with n = 4-18, and two different kinds of bottom electrodes (AgTS or AuTS) are employed to assess the mechanism underlying the observed changes in tunneling currents. Measurements of current density through junctions immersed in perfluorocarbons (II) are comparable to junctions measured in air. Junctions immersed in other organic liquids show reductions in the values of current density, compared to the values in air, ranging from 1 (III) to 5 orders of magnitude (IV). We interpret the most plausible mechanism for these reductions in current densities to be an increase in the length of the tunneling pathway, reflecting the formation of thin (0.5-1.5 nm) liquid films at the interface between the SAM and the Ga2O3/EGaIn electrode. Remarkably, the thickness of the liquid film─estimated by the simplified Simmons model, measurements of electrical breakdown of the junction, and simulations of molecular dynamics─is consistent with the existing observations of structured liquid layers that form between two flat interfaces from measurements obtained by the surface force apparatus. These results suggest the use of the EGaIn junction and measurements of charge transport by tunneling as a new form of surface analysis, with the applications in the study of near-surface, weak, molecular interactions and the behavior of liquid films adjacent to non-polar interfaces.

Prefrontal EEG slowing, synchronization, and ERP peak latency in association with predementia stages of Alzheimer's disease.

Background: Early screening of elderly individuals who are at risk of dementia allows timely medical interventions to prevent disease progression. The portable and low-cost electroencephalography (EEG) technique has the potential to serve it. Objective: We examined prefrontal EEG and event-related potential (ERP) variables in association with the predementia stages of Alzheimer's disease (AD). Methods: One hundred elderly individuals were recruited from the GARD cohort. The participants were classified into four groups according to their amyloid beta deposition (A+ or A-) and neurodegeneration status (N+ or N-): cognitively normal (CN; A-N-, n = 27), asymptomatic AD (aAD; A + N-, n = 15), mild cognitive impairment (MCI) with AD pathology (pAD; A+N+, n = 16), and MCI with non-AD pathology (MCI(-); A-N+, n = 42). Prefrontal resting-state eyes-closed EEG measurements were recorded for five minutes and auditory ERP measurements were recorded for 8 min. Three variables of median frequency (MDF), spectrum triangular index (STI), and positive-peak latency (PPL) were employed to reflect EEG slowing, temporal synchrony, and ERP latency, respectively. Results: Decreasing prefrontal MDF and increasing PPL were observed in the MCI with AD pathology. Interestingly, after controlling for age, sex, and education, we found a significant negative association between MDF and the aAD and pAD stages with an odds ratio (OR) of 0.58. Similarly, PPL exhibited a significant positive association with these AD stages with an OR of 2.36. Additionally, compared with the MCI(-) group, significant negative associations were demonstrated by the aAD group with STI and those in the pAD group with MDF with ORs of 0.30 and 0.42, respectively. Conclusion: Slow intrinsic EEG oscillation is associated with MCI due to AD, and a delayed ERP peak latency is likely associated with general cognitive impairment. MCI individuals without AD pathology exhibited better cortical temporal synchronization and faster EEG oscillations than those with aAD or pAD. Significance: The EEG/ERP variables obtained from prefrontal EEG techniques are associated with early cognitive impairment due to AD and non-AD pathology. This result suggests that prefrontal EEG/ERP metrics may serve as useful indicators to screen elderly individuals' early stages on the AD continuum as well as overall cognitive impairment.