Repair of monolithic zirconia restorations with different direct resin composites: effect on the fatigue bonding and mechanical performance.

OBJECTIVE: The study aims to evaluate the shear bond and flexural strength fatigue behavior of yttrium-stabilized zirconia (4YSZ) repaired using different resin composites. MATERIALS AND METHODS: Cylindric specimens of 4YSZ were obtained for the bond strength (Ø = 6 mm, 1.5 mm of thickness) and biaxial flexural strength (Ø = 15 mm, 1 mm of thickness) fatigue tests and divided into 3 groups according to the repair resin composite: EVO (nanohybrid), BULK (bulk-fill), and FLOW (flowable). The zirconia surface was air-abraded with alumina particles, a 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) primer was applied, and the resin composite was build-up over the zirconia. Fatigue shear bond strength and flexural fatigue strength tests were performed (n = 15). One-way ANOVA and Tukey post hoc tests were carried out for both outcomes, besides scanning electron microscopy and finite element analysis. RESULTS: The repair material affected the fatigue shear bond strength of zirconia ceramic. The BULK group (18.9 MPa) depicted higher bond strength values than FLOW (14.8 MPa) (p = 0.04), while EVO (18.0 MPa) showed similar results to both groups. No effect was observed for the mechanical behavior (p = 0.53). The stress distribution was similar for all groups. CONCLUSION: The repair of yttrium-stabilized zirconia (4YSZ) ceramics with bulk-fill resin composites was the best option for high fatigue bond strength. However, the fatigue mechanical performance was similar regardless of the applied repair material. CLINICAL RELEVANCE: The repair of yttrium-stabilized zirconia (4YSZ) monolithic restorations may be performed with nanohybrid and bulk-fill resin composites in order to promote longevity in the treatment.

Effect of radiotherapy, immediate dentin sealing and irrigation simulating single- or two-visits endodontic treatment on the bond strength to pulp chamber dentin: an in vitro study.

This study aimed to evaluate the influence of radiotherapy and different endodontic treatment protocols on the bond strength to pulp chamber dentin. Eighty mandibular molars were randomly divided into two groups (n = 40): non-irradiated and irradiated (60 Gy). The pulp chambers were sectioned, and each group was subdivided (n = 8), according to the endodontic treatment protocol: no treatment (Control); Single-visit; Two-visits; Immediate dentin sealing (IDS) + single-visit; and IDS + two-visits. Each endodontic treatment visit was simulated through irrigation with 2.5% NaOCl, 17% EDTA and distilled water. IDS was performed by actively applying two coats of a universal adhesive to the lateral walls of the pulp chamber. After, the pulp chambers were restored with resin composite and four sticks were obtained for microtensile test. In addition, the dentin of the pulp chamber roof was assessed for surface roughness, chemical composition, and topography after each treatment protocol. Two-way ANOVA, Tukey's post hoc, Mann-Whitney, Kruskal-Wallis and Dunn's post hoc were performed (α = 5%). The treatment protocol affected bond strength (p < 0.05), while the irradiation did not (p > 0.05). The control group presented the highest values (p < 0.05). The single-visit group demonstrated better performance compared to the other groups (p < 0.05), which did not differ from each other (p > 0.05) The use of IDS changed the surface roughness (p < 0.05), chemical composition (p < 0.05) and topography of the dentin. In conclusion, the treatment protocol influenced dentin adhesion, while irradiation did not.

Influence of CAD-CAM milling strategies on the outcome of indirect restorations: A scoping review.

STATEMENT OF PROBLEM: The influence of computer-aided manufacturing (CAM) parameters and settings on the outcomes of milled indirect restorations is poorly understood. PURPOSE: The purpose of this scoping review was to summarize the current CAM systems, parameters, and setting changes, and their effects on different outcomes of milled indirect restorations and aspects related to their manufacture. MATERIAL AND METHODS: The protocol of this review is available online (https://osf.io/x28ps/). Studies that used at least 2 different parameters (CAM units, number of axes, digital spacers, or protocols with different rotatory instruments, grit-sizes, milling speed, or others) for milling indirect restorations were included. A structured search up to July 2023 was performed by 2 independent reviewers for articles written in English in LILACS, MEDLINE via PubMed, EMBASE, Web of Science, and Scopus. RESULTS: Of 1546 studies identified, 22 were included in the review. Discrepancies were found between the planned and actual measured cement space, with a decreasing linear relationship impacting restoration adaptation at different points. The CEREC MC XL milling machine was the most used system in the included studies, with variations in bur types, milling modes, and number of burs uses affecting internal fit and surface trueness. The results demonstrated the better adaptation of restorations made with 5-axis over 3-axis milling machines. Lithium disilicate and zirconia were the most commonly used materials, and crowns and inlays were popular designs. Marginal and internal adaptation were the primary outcomes assessed using the various techniques. CONCLUSIONS: The study presented a comprehensive exploration of CAM systems and parameters, and their influence on indirect restorations. The planned cement space was not properly reproduced by the milling. Bur characteristics can affect restoration fit and trueness. The 5-axis units seem to result in better-adapted restorations compared with 3- and 4-axis units.

Effect of calcium hypochlorite and sodium thiosulfate on the bond strength to pulp chamber dentin: A laboratory investigation.

This study aimed to compare the effect of sodium hypochlorite (NaOCl) and calcium hypochlorite [Ca(OCl)2 ] on the bond strength to pulp chamber dentin when followed or not by the use of sodium thiosulfate (Na2 S2 O3 ). The pulp chamber of fifty human molars were divided into five groups (n = 10) according to the immersion protocol: 2.5% NaOCl; 2.5% NaOCl + 5% Na2 S2 O3 ; 2.5% Ca(OCl)2 ; 2.5% Ca(OCl)2 + 5% Na2 S2 O3 ; and 0.9% sodium chloride (NaCl; control). Subsequently, the samples were restored with resin composite. Three sticks each were obtained and subjected to microtensile testing. SEM/EDS analyses of the pulp chamber roof (n = 8) were carried out for mineral quantification. Elemental analysis data were investigated via one-way ANOVA and Tukey's post hoc, and bond strength data by post hoc pairwise comparisons using the Kruskal-Wallis test. Use of 2.5% NaOCl was associated with the lowest value of bond strength, while 2.5% Ca(OCl)2 had similar bond strength to that of the 0.9% NaCl control. Using 5% Na2 S2 O3 was able to increase the bond strength after 2.5% NaOCl, but not after 2.5% Ca(OCl)2 . The group treated only with 2.5% Ca(OCl)2 had a higher Ca/P ratio on the dentin surface. Dentin treated with Ca(OCl)2 was not affected by Na2 S2 O3 and showed bond strength similar to the 0.9% NaCl.

Longevity of metal-ceramic single crowns cemented onto resin composite prosthetic cores with self-adhesive resin cement: an update of a prospective analysis with up to 106 months of follow-up.

OBJECTIVES: To evaluate the longevity of metal-ceramic single crowns cemented onto resin composite prosthetic cores using a self-adhesive resin cement in a prospective clinical descriptive study. METHODS: A total of 152 teeth were endodontically treated and received resin composite prosthetic cores and metal-ceramic crowns cemented with a self-adhesive resin cement. The patients included in the sample were recalled for clinical and radiography evaluation in an up-to-106-month period after the final cementation procedures, with an average of 62 months of follow-up. 91.5% of the sample (142 teeth) were evaluated regarding the treatment survival rate, analyzed considering the loss of crown retention (crown debonding) and tooth loss as the primary outcome. In addition, post debonding, and root fracture occurrences were also recorded as secondary outcomes to evaluate the success rate of the prosthetic treatment. The aesthetic parameters were also evaluated according to the FDI criteria. The Kaplan-Meier method and Cox regression with 95% confidence interval were applied for the statistical analysis. RESULTS: Regarding the primary outcome, the metal-ceramic crowns cemented with self-adhesive resin cement presented a high survival rate (91.5%), with 8 crown debondings and 3 tooth losses (1 due to caries and 2 due to periodontal disease) occurring after the evaluation period. For secondary outcomes, 9 root fractures and 4 post debondings occurred, generating a success rate of 72%. All crowns had a score 1 on the FDI criteria, indicating that they were clinically excellent or very good regarding the aesthetic parameters. CONCLUSION: The metal-ceramic crowns luted with a self-adhesive resin cement presented a survival rate of 91.5% after an average of 62 months of follow-up. Furthermore, the restorations remained aesthetically satisfactory over time, without changes that would indicate prosthetic retreatment. A success rate of 72% was obtained considering the secondary outcome, mainly related to intraradicular retainer failures (root fractures or post debonding). CLINICAL SIGNIFICANCE: The self-adhesive resin cement is clinically indicated for cementation of metal-ceramic crowns onto resin composite prosthetic cores.

Survival rate and treatment success of glass fiber posts cemented with two adhesive cementation strategies after up to 106 months: a randomized clinical trial.

OBJECTIVES: The objective of this study is to evaluate the longevity of two fiber post cementation strategies in a prospective, multicenter, non-inferiority, double-blind randomized controlled trial. METHODS: A total of 152 teeth, with adequate endodontic treatment and loss of coronal structure and bilateral simultaneous posterior occlusal contacts, were randomly allocated to receive glass fiber posts cemented with a conventional cementation strategy (CRC group: adhesive system + resin cement) (Adper Single Bond + RelyX ARC; 3 M-ESPE) or a self-adhesive cementation strategy (SRC group: self-adhesive resin cement; RelyX U100/U200; 3 M-ESPE). The patients were recalled annually for clinical and radiographical evaluation with a 93% recall rate (142 teeth, with 74 at CR groups and 68 at SRC group). The primary outcome was survival rate, considering the fiber post debonding (loss of retention). The secondary outcome included the success rate of the prosthetic treatment with crown debonding, post fracture, and tooth loss (not related to post failure). Both outcomes were evaluated annually. The Kaplan-Meier method and Cox regression with 95% confidence interval were used for the statistical analysis. RESULTS: For the primary outcome (failures directly related to fiber posts cementation strategy), there were 4 fiber post debondings (2 per group), 8 root fractures (3 for SRC group and 5 for CRC group), and one mixed failure (debonding combined with root fracture for CRC), with both strategies presenting similar survival rates (p = 0.331), with 88.9% for the CRC group and 90.9% for the SRC group. For the secondary outcome (failures not related to fiber post cementation strategies), there were 8 crown debondings, 3 post fractures, and 3 tooth losses, with no statistically difference between groups (p = 0.701), with 77% for SRC and 82% for CRC. CONCLUSION: Fiber post cementation strategies with conventional or self-adhesive resin cement presents similar tooth survival and success rates. TRIAL REGISTRATION: NCT01461239 CLINICAL RELEVANCE: Both adhesive cementation strategies led to high survival and success rates and are indicated for fiber post cementation, even after a long follow-up period (up to 106 months).

Fatigue behavior, failure mode, and stress distribution of occlusal veneers: influence of the prosthetic preparation cusp inclinations and the type of restorative material.

OBJECTIVE: To evaluate the effects of cusp inclination of the prosthetic preparation's occlusal surface and type of restorative material on the fatigue behavior, failure mode, and stress distribution of occlusal veneers. MATERIALS AND METHODS: Glass fiber-reinforced epoxy resin prosthetic preparations for occlusal veneers with three different occlusal surface cusp inclination degrees (0°, 15°, and 30°) were produced and assigned into six testing groups (n = 11) according to the cusp inclination (0°, 15°, or 30°) and type of restorative material (lithium disilicate-LD or resin composite-RC). Despite different substrate preparation cusp inclination degrees, the restorations were designed maintaining 30° inclination between the cusps at the occlusal surface and a thickness of 0.7 mm at the central groove region of the restorations to be machined in a CAD/CAM system. After cementation, the specimens were stored for about 7 days (under water at 37 °C), and subsequently submitted to a load to failure test (n = 2) and an intermittent cyclic fatigue test (n = 9) (initial load: 100 N; step size: 50 N; cycles/step: 10,000; loading frequency: 20 Hz; loading piston: 6-mm-diameter stainless steel) until observing cracks. The data were analyzed by two-way ANOVA, Kaplan-Meier, and Mantel-Cox post hoc tests. Finite element analysis (FEA) and fractographic analyses were performed. RESULTS: The fatigue performance of LD and RC occlusal veneers was evaluated based on different prosthetic preparation cusp inclinations. The 0° inclination showed the best fatigue performance for both materials (LD: 944N, RC: 861N), while the 15° and 30° inclinations had lower values (LD: 800N and 533N, RC: 739N and 717N, respectively). The study also found that for a 0° inclination, LD occlusal veneers performed better than RC ones (LD: 944 N > RC: 861N), while for a 30° inclination, RC occlusal veneers had better fatigue performance than LD ones (LD: 533N < RC: 717N). No significant difference was observed between the materials for a 15° inclination (LD: 800N = RC: 739N). The FEA results showed a higher tensile stress concentration on lithium disilicate than on resin composite occlusal veneers. All lithium disilicate occlusal veneers showed radial crack failures, while resin composite occlusal veneers showed Hertzian cone cracks and radial cracks combined. CONCLUSION: Considering mechanical perspective only, RC occlusal veneers should be indicated when prosthetic preparation cusps inclinations are 30°. When 0° prosthetic preparation cusps inclinations are observed, LD occlusal veneers will behave mechanically better. When a 15° cusp inclination is preserved, both restorative materials behave similarly.

Resin composite layering on discolored substrates ensures masking ability for monolithic ceramics.

OBJECTIVE: the aim of this study was to evaluate the effect of resin composite layering on discolored substrates to obtain masking ability with monolithic ceramics. MATERIALS AND METHODS: Four groups (n = 8) of computer-aided design/computer aided manufacturing (CAD/CAM) monolithic ceramics, shade A1, with thicknesses of 1.0 and 1.5 mm, were tested: feldspathic (FC), leucite-reinforced (LC), lithium disilicate-reinforced (LD), and translucent zirconia (5YSZ). Five substrates were used: A1 (used as reference), A3.5, C4, and coppery and silvery metals. The substrates were separated as non-layered or layered (with flowable opaque resin composite (FL), white opaque restorative resin composite (WD), and A1-shaded opaque restorative resin composite (A1D)). Resin composite layers of 0.5 and 1.0 mm were tested. The try-in paste, shade A1, was used as a luting agent. Translucency parameter (TP00 ) was assessed for the ceramics. Color differences (∆E00 ) were assessed for the restorative ceramics and resin composite layers over discolored substrates with the CIEDE2000 formula. The results were compared statistically, and descriptively with acceptability (AT, 1.77) and perceptibility (PT, 0.81) thresholds. RESULTS: Feldspathic showed the highest TP00 (for both ceramic thicknesses) and LD the lowest (for 1.5 mm of ceramic thickness) (P < 0.001). For substrate A3.5, layering with 1.0 mm of A1D or WD ensured ∆E00 below PT for all ceramics tested (P < 0.001). The use of 0.5 mm of FL or 1.0 mm of A1D associated with ceramics LC, LD, and 5YSZ ensured ∆E00 below AT for substrates C4 and coppery metal (P < 0.001). Silvery background layered with 0.5 mm of FL presented ∆E00 below AT for all ceramics and ∆E00 below PT for lithium disilicate of 1.0 mm of thickness (∆E00 = 0.72). CONCLUSIONS: Layering severely discolored substrates with selected opaque resin composites ensures masking ability for restoration with CAD/CAM monolithic ceramics. CLINICAL SIGNIFICANCE: Severely discolored substrates are predictably restored with monolithic CAD/CAM ceramics by performing a previous layering of the substrate with opaque resin composite.

Masking ability of resin composites: A scoping review.

OBJECTIVE: To map the existing evidence regarding the masking ability of resin composites. OVERVIEW: The literature search was conducted electronically, based on the PRISMA Extension for Scoping Reviews-online protocol at https://osf.io/m2h67/ with no language or time restrictions. Two independent reviewers conducted the screening, and a third reviewer was consulted in case of disagreement. Studies that evaluated resin composite masking ability regardless of background, application technique, thickness, or number of layers were selected. The search found 2995 potentially eligible studies. After removal of duplicates (657), irrelevant articles (2323), 15 citations met the eligibility criteria based on title and abstract, and eight studies were included based on full text analysis (seven in vitro, and one case report). Acceptable masking ability is obtained by one layer of opaque shade resin composite or by the layering technique. A black background is masked with 1.0- to 2.0 mm-thick layers of opaque shade resin composites. Masking of the C4 background is achieved with one layer of 0.5- to 1.5 mm-thick opaque shade resin composite or by the layering technique using different combinations of enamel body and dentin shades with a final thickness of 1.5 mm. CONCLUSIONS: Acceptable masking of C4 shade background is achieved with one layer of opaque shade composite at least 0.5 mm-thick or by different combinations of the layering technique, with a final thickness of 1.5 mm. Acceptable masking of the black background of the oral cavity is achieved with a resin composite of at least 1.0 mm opaque shade. CLINICAL SIGNIFICANCE: The thickness of the resin composite layer required to achieve adequate masking is variable and depends on the translucency/opacity of the tested resin composites and the background shade.

Evaluation paste removal method and bond strength between resin cement and lithium disilicate ceramic: An in vitro study.

STATEMENT OF PROBLEM: After the use of evaluation paste, residue can remain on the bonding surface. However, how adhesion to lithium disilicate ceramic is affected is unclear. PURPOSE: The purpose of this in vitro study was to determine the effectiveness of lithium disilicate cleaning after contamination with an evaluation paste and before the application of a resin cement. MATERIAL AND METHODS: Rectangular lithium disilicate (IPS e.max CAD) specimens were obtained with a simulated milled surface, crystallized, etched with 5% hydrofluoric (HF) acid, and contaminated with an evaluation paste. The cleaning methods tested were air-water spray (SPRAY), 37% phosphoric acid (HPO), ultrasonic bath (ULT), cleaning paste (IVOC), and a conventional surface treatment (HF + silane-HF+SIL). The control (CTRL) group was not contaminated. After silane had been applied, resin cement cylinders were fabricated and light polymerized. Half of the cylinders (n=56) were tested for microshear bond strength at baseline (24 hours), and the other half after 210 days of water storage and 25 000 thermal cycles. Surface roughness, failure analysis, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were performed. Statistical analysis was performed with the Kruskal-Wallis and Mann-Whitney tests for surface roughness and the 2-way ANOVA and Bonferroni post hoc tests for bond strength (α=.05). RESULTS: At baseline, only SPRAY did not restore the bond strength compared with CTRL. After aging, the bond strengths of SPRAY and IVOC were lower than of CTRL (P<.05); no significant difference was found between CTRL, HPO, ULT, and HF+SIL (P>.05). EDS demonstrated the presence of carbon in the SPRAY and ULT groups, probably remnants of the evaluation paste. SEM analysis identified such remnants in the SPRAY group only. CONCLUSIONS: For optimal bond strength between lithium disilicate and resin cement after evaluation paste use, cleaning the ceramic surface with 37% phosphoric acid, ultrasonic bath, or with hydrofluoric acid worked best.

Influence of coloring techniques on the surface characteristics and color stability of a monolithic zirconia ceramic.

STATEMENT OF PROBLEM: The color of monolithic zirconia restorations is obtained by presintering or postsintering coloring techniques. However, studies on the differences in surface characteristics and their influence on color stability are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the influence of shading and staining techniques for a zirconia ceramic on the surface characteristics and colorimetric parameters (color difference, translucency, and whiteness index) after exposure to coffee or red wine and then polishing. MATERIAL AND METHODS: Ceramic disks (N=30; Ø10×1mm) were allocated into 3 groups: preshaded-shaded by the manufacturer (IPS e.max ZirCAD MT, shade A2); manually shaded-unshaded zirconia (IPS e.max ZirCAD MT, bleaching shade-BL) colored by the brushing technique, before sintering; stained-unshaded zirconia (IPS e.max ZirCAD MT BL) colored by the staining technique, after sintering. Spectrophotometric color assessments ensured the same initial perceived color (Vita Classical A2) for specimens included in the study (∆E00<1.77 acceptability threshold). Surface characteristics were assessed by scanning electron microscopy and atomic force microscopy. The specimens were immersed in coffee (n=5) or red wine (n=5) for 12 and 24 days and subsequently polished. The data were statistically and descriptively analyzed for color differences (∆E00), translucency parameters (TP00), and whiteness indexes for dentistry (WID), considering acceptability and perceptibility thresholds. RESULTS: The shaded groups found an irregular ceramic surface with uniformly sized zirconia crystals. The stained group found a glass-covered smoother surface. Significant alterations in color parameters (∆E00, TP00, WID) were observed with immersion in pigmenting beverages (P<.001) both after 12 days, and after 24 days. The shaded specimens had greater color alterations after immersion but benefited from the polishing procedure, which reduced color differences below an acceptable threshold in comparison with the baseline. Stained specimens had lower color alterations after immersion, but the polishing protocol was detrimental as it whitened the ceramic by subsurface exposure. CONCLUSIONS: The coloring technique influences the surface characteristics of zirconia ceramic and also the color parameters after exposure to colored beverages and polishing.

Fit and fatigue behavior of CAD-CAM lithium disilicate crowns.

STATEMENT OF PROBLEM: New computer-aided design and computer-aided manufacturing (CAD-CAM) lithium disilicate glass-ceramics have been marketed. However, information concerning their biomechanical behavior is lacking. PURPOSE: The purpose of this in vitro study was to compare the fit and fatigue behavior of two recently introduced CAD-CAM lithium disilicate materials with the standard IPS e.max CAD ceramic and to investigate the effect of the thermal treatment for crystallization on crown fit. MATERIAL AND METHODS: Monolithic crowns (n=15) were milled from 3 CAD-CAM lithium disilicates: IPS e.max CAD (Ivoclar AG), Rosetta SM (Hass), and T-lithium (Shenzhen Upcera Dental Technology). Marginal and internal fit were evaluated using the replica technique before and after crystallization, and the fatigue behavior of the luted crowns was evaluated by the step-stress method. One-way ANOVA and the Tukey test were used to compare fit among the materials. Fatigue failure load was evaluated by the Kaplan-Meier and Mantel-Cox tests. The effect of crystallization on fit was evaluated with the paired t test (α=.05). RESULTS: Marginal fit was different between IPS e.max CAD (74 µm) and Rosetta SM (63 µm) (P=.02). T-lithium was similar to the other ceramics (68 µm) (P>.05). Occlusal internal space was similar among all materials (P=.69). Fatigue failure loads of Rosetta SM (1160 N) and T-lithium (1063 N) were similar to IPS e.max CAD (1082 N) (P>.05). The fatigue failure load of Rosetta SM was higher than that of T-lithium (P=.04). Crystallization reduced the axial internal space of all materials (P<.05) without significantly affecting marginal fit (P>.05). CONCLUSIONS: The fit and fatigue behavior of Rosetta SM and T-lithium were similar to that of IPS e.max CAD. Crystallization reduced the internal space of the crowns.

Fatigue survival of endodontically treated teeth restored with different fiber-reinforced composite resin post strategies versus universal 2-piece fiber post system: An in vitro study.

STATEMENT OF PROBLEM: Various strategies have been proposed to reduce the cement space of foundation restorations for endodontically treated teeth. However, they may add more operative steps, or the dentist must keep different sizes of drills and posts in stock. A 2-piece universal adjustable post system has been developed to overcome this problem, but whether the system has acceptable fatigue survival performance is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the fatigue survival and stress distribution of endodontically treated teeth without a ferrule and restored with different glass fiber post strategies versus a recently introduced universal 2-piece fiber post system. MATERIAL AND METHODS: Bovine incisor roots were randomly assigned to 3 groups as per the post used (n=13): adapted glass fiber post with post space preparation of the same size, composite resin-custom glass fiber post (CTM), and universal 2-piece glass fiber-reinforced composite resin post (UNI). The posts were adhesively luted, the composite resin core was added, and a composite resin crown was produced with computer-aided design and computer-aided manufacturing (CAD-CAM), and then adhesively luted to each core. A fatigue test was performed with the stepwise stress method (10 000 cycles/step; 20 Hz; load=100 N to 750 N; step=50 N) until fracture, and the failure mode analyzed. The stress distribution was evaluated by finite element analysis with the maximum principal stress criteria by following the parameters of the in vitro test. The solids were considered homogeneous, linear, and isotropic, except for the glass fiber post (orthotropic), and a load of 450 N at 30 degrees was applied. The fatigue failure load and the number of cycles for failure were analyzed with Kaplan-Meier and Mantel-Cox (log rank test) (α=.05). The finite element analysis results were analyzed with colorimetric graphs. RESULTS: The highest fatigue failure load and the number of cycles for failure were found in the UNI system, whereas the lowest results were found in the CTM group. All groups exhibited repairable failures. The finite element analysis showed the lowest stress in root dentin in the UNI system. The CTM system had the largest stress regions at the dentin and dentin-core interface. CONCLUSIONS: The use of a 2-piece universal glass fiber post system resulted in more fatigue behavior compared with composite resin-custom glass fiber posts.

Novel cinnamon-laden nanofibers as a potential antifungal coating for poly(methyl methacrylate) denture base materials.

OBJECTIVES: To modify the surface of denture base material by coating it with cinnamon-laden nanofibers to reduce Candida albicans (C. albicans) adhesion and/or proliferation. MATERIALS AND METHODS: Heat-cured poly(methyl methacrylate) (PMMA) specimens were processed and coated, or not, with cinnamon-laden polymeric nanofibers (20 or 40 wt.% of cinnamon relative to the total polymer weight). Scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR) analyses of the nanofibers were performed. Antifungal activity was assessed through agar diffusion and colony-forming unit (CFU/mL) assays. Representative SEM morphological analysis was carried out to observe the presence/absence of C. albicans on the fibers. Alamar blue assay was used to determine cell toxicity. Analysis of variance and the Tukey's test were used to analyze the data (α = 0.05). RESULTS: SEM imaging revealed nanofibers with adequate (i.e., bead-free) morphological characteristics and uniform microstructure. FTIR confirmed cinnamon incorporation. The cinnamon-laden nanofibers led to growth inhibition of C. albicans. Viable fungal counts support a significant reduction on CFU/mL also directly related to cinnamon concentration (40 wt.%: mean log 6.17 CFU/mL < 20 wt.%: mean log 7.12 CFU/mL), which agrees with the SEM images. Cinnamon-laden nanofibers at 40 wt.% led to increased cell death. CONCLUSIONS: The deposition of 20 wt.% cinnamon-laden nanofibers onto PMMA surfaces led to a significant reduction of the adhesive and/or proliferative ability of C. albicans, while maintaining epithelial cells' viability. CLINICAL RELEVANCE: The high recurrence rates of denture stomatitis are associated with patient non-adherence to treatments and contaminated prostheses use. Here, we provide the non-patients' cooperation sensible method, which possesses antifungal action, hence improving treatment effectiveness.

Sintering mode of a translucent Y-TZP: Effects on its biaxial flexure fatigue strength, surface morphology and translucency.

OBJECTIVE: This investigation evaluated the effect of two sintering modes of a translucent zirconia (Y-TZP) on its surface roughness, topography, phase-transformation (t → m), translucency and biaxial flexure fatigue strength. MATERIALS AND METHODS: To do so, 50 Y-TZP discs (Ø = 15 mm; thickness = 1.2 mm; IPS e.max ZirCAD LT) were prepared and divided into two groups: Standard mode (SM) and Fast mode (FM). Staircase fatigue testing was performed (piston-on-three balls set-up, ISO 6872:2015), as well as surface roughness, profilometry, scanning electron microscopy (SEM-FEG), energy dispersive X-ray spectroscopy (EDX), phase transformation (t → m) using X-ray diffraction analysis (XRD), translucency parameter analysis (TP and TP00 ) and fractography. RESULTS: The results showed no statistical significant differences for roughness parameters (p > 0.05, SM: Ra = 0.13 ± 0.02, Rz = 1.21 ± 0.26 and RSm = 24.91 ± 2.19; FM: Ra = 0.14 ± 0.03, Rz = 1.32 ± 0.25 and RSm = 24.68 ± 2.16) or flexural fatigue strength (SM: 512 (464-560) MPa; FM: 542 (472-611) MPa) between the groups. In addition, similarity in surface morphological features (SEM and profilometry), composition and phases (EDX and XRD) was observed between the firing protocols. Fractography showed that the failure origin occurred on the tensile side. Sintering mode did not affect the TP (F = 0.001, p = 0.97) and TP00 (F = 0.12, p = 0.72). CONCLUSIONS: Therefore, the fast-sintering mode is suggested as a viable alternative to the standard mode since it does not influence the evaluated surface morphology, microstructure, fatigue strength and translucency of a translucent monolithic zirconia. CLINICAL SIGNIFICANCE: The fast sintering mode is a viable alternative for zirconia without compromising its topography, microstructure, mechanical performance or translucency.

Maintenance protocols for implant-supported dental prostheses: A scoping review.

STATEMENT OF THE PROBLEM: Biological complications of implant-supported prostheses remain a concern. Therefore, standardizing hygiene protocols to promote their maintenance is important. PURPOSE: The purpose of this scoping review was to identify available hygiene guidance for home care procedures, as well as periodicity and protocols for the professional maintenance of implant-supported prostheses. MATERIAL AND METHODS: This study was based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines, and the study protocol was made available at: https://osf.io/5jdeh/. The search was last performed in the PubMed database on March 15, 2022 and was undertaken by 2 independent researchers. Clinical studies and reviews that evaluated home care and maintenance protocols for dental implant-supported prostheses (fixed or removable), without language restriction or year of publication, were included. A descriptive analysis was performed considering study characteristics (study design, restorative assembly, maintenance strategies, eligibility criteria, number of included studies, quality/level of evidence, and main findings). RESULTS: The initial search yielded 3138 studies, of which 18 were included for descriptive analysis (6 critical reviews, 4 clinical trials, 3 systematic reviews, 2 guideline reports, 2 retrospective studies, and 1 transversal study). The main instrument recommended for home care was the use of a conventional toothbrush associated with triclosan-containing toothpaste in addition to interproximal aids (brushes or floss) for all types of restorations. The use of irrigation instruments was also frequently considered. For professional maintenance, almost all studies reported a positive effect of regular recalls every 3 months during the first year, followed by less regular recalls according to the motivation of the patient and home care efficacy. At each recall, the professional should evaluate the patient history, oral tissues, implant, abutments, and restorations, as well as perform professional cleaning of the prostheses with appropriate instruments so that the implants and abutments may be preserved. CONCLUSIONS: Establishing an adequate hygiene protocol is indispensable for implant-supported restorations. To do so, the professional must guide and support the patient's home care by taking into account the patient's motivation and efficacy during the hygiene procedures. Also, for professional maintenance, the periodicity of recalls should be constant and include an evaluation of the condition of the restoration and adjacent tissues, followed by professional cleaning of prostheses, implants, and abutments, in addition to new instructions to improve patient home care.

Factors influencing the clinical performance of the restoration of endodontically treated teeth: An assessment of systematic reviews of clinical studies.

STATEMENT OF PROBLEM: How best to restore endodontically treated teeth is still unclear because many types of material and techniques are involved. PURPOSE: The purpose of this overview of systematic reviews of clinical studies was to assess the available evidence-based literature on the influence of associated clinical factors on the clinical performance (survival, failure rate, or success) of restored endodontically treated teeth. MATERIAL AND METHODS: PubMed, Scopus, and Web of Science were searched from inception until September 27, 2021, to identify systematic reviews. Two reviewers independently screened titles, abstracts, and full-text articles, and each reviewer extracted the data of half of the included studies. A single reviewer with an independent verifier completed the quality appraisal. A descriptive analysis of the collected data was made. RESULTS: A total of 36 systematic reviews fulfilled the inclusion criteria. The factors most assessed were the type of coronal restorative technique (n=22) and type of post (n=22). The results indicated that metal and fiber posts seem to present similar clinical performance, endocrowns could be a suitable restorative option, there is no evidence to confirm whether single crowns are better or worse than direct restoration, the maintenance of the coronal structure is a fundamental factor, and the ferrule effect is still a controversial topic. Most of the studies (n=30, 81%) presented a final Grading of Recommendations, Assessment, Development and Evaluations (GRADE) rating of "critically low." CONCLUSIONS: The post type does not appear to influence the clinical performance of restored endodontically treated teeth. However, conclusive evidence to suggest how different materials or techniques for restoring coronal tooth structure affect the clinical performance of such restorations, as well as the impact of the ferrule effect, is still lacking.

Masking ability of implant abutment substrates by using different ceramic restorative systems.

STATEMENT OF PROBLEM: Information regarding the masking ability of ceramic crowns over different implant abutment materials is scarce. PURPOSE: The purpose of this in vitro study was to evaluate the masking ability of different monolithic or bilayer ceramic materials with different thicknesses over substrates indicated for implant restorations by using opaque and translucent evaluation pastes. MATERIAL AND METHODS: Disk-shaped specimens, shade A1 (VITA Classic; Ø10×1.5 to 2.5 mm), of different ceramics (a bilayer system [yttria-stabilized zirconia infrastructure+porcelain veneer: Zir+Pc] and monolithic systems [lithium disilicate under low, medium, or high translucency: LtLD, MtLD, or HtLD, respectively, and a high-translucent yttria-stabilized zirconia: HtZir]) were made (n=4). The color difference (ΔE00) was assessed by using the CIEDE2000 formula and considering the different ceramic systems over 5 implant abutment materials (A1 shade Zir [Zir A1]; white Zir [White Zir]; A1 low-translucency lithium disilicate [LD]; polyetheretherketone [PEEK]; and titanium [Ti]) when using 2 different evaluation pastes (translucent or opaque). The control comparison was the restorative material positioned over the Zir A1 substrate with a translucent evaluation paste. Statistical analysis was made by using a 2-way ANOVA and Tukey post hoc tests (α=.05) for ΔE00 data considering the restorative material and luting agent factors as their association. Additionally, ΔE00 data were qualitatively analyzed considering the acceptability and perceptibility thresholds. The translucency parameter (TP00) of each restorative material was evaluated, and data were submitted to 1-way ANOVA and Tukey post hoc tests (α=.05). RESULTS: The most predictable masking ability was seen with Zir+Pc regardless of the evaluation paste used. Nevertheless, under 1.5-mm thickness, Zir+Pc did not adequately mask Ti (ΔE00>1.77). Most monolithic ceramics did not mask discolored substrates (PEEK or Ti, ΔE00>1.77). The exception was HtZir, which presented acceptable masking ability over PEEK at 2.5-mm thickness with both evaluation pastes (ΔE00<1.77). Regardless of the restorative material thickness, Zir+Pc showed the lowest (P<.05) TP00 values (TP00=3.45 at 1.5-mm thickness; TP00=2.00 at 2.5-mm thickness), and HtLD presented the highest (P<.05, TP00=23.50 at 1.5-mm thickness; TP00=13.36 at 2.5-mm thickness). HtZir showed similar TP00 to MtLD at 1.5-mm thickness and similar TP00 to Zir+Pc when used at 2.5-mm thickness (P>.05). CONCLUSIONS: Monolithic ceramics should be used with caution over discolored implant abutments. Bilayer systems (Zir+Pc) were the most predictable approach to adequately masking discolored substrates such as PEEK or Ti. An increased restoration thickness provided higher masking ability for all restorative materials tested.

Influence of connector cross-sectional geometry on the load-bearing capacity under fatigue of implant-supported zirconia fixed partial prosthesis.

STATEMENT OF PROBLEM: Zirconia has been reported to be suitable for multiunit monolithic restorations. However, as the connector region is the weakest part of the system, studies are needed to determine the optimal connector geometry. PURPOSE: The purpose of this in vitro study was to evaluate the load-bearing capacity under fatigue of implant-supported fixed partial prostheses made of monolithic zirconia with different connector cross-sectional geometries. MATERIAL AND METHODS: Three-unit monolithic fixed partial prostheses (from mandibular second premolar to the second molar) were fabricated in zirconia (Zenostar T) by computer-aided design and computer-aided manufacture (CAD-CAM). Different connector cross-sectional geometries, with an area of 9 mm2, were tested (n=10): round, square with rounded angles, or trapezoid with rounded angles. The prostheses were screwed over 2 implants and inserted into acrylic resin bases. The specimens were submitted to a mechanical fatigue test until failure, with load applied to the pontic using the stepwise stress methodology (initial load of 100 N for 5000 cycles, followed by an increase to 200 N for 20 000 cycles, with a subsequent increase of 50 N each step). For data analysis, fatigue failure load (FFL) and cycles for fatigue failure (CFF) were recorded. Failed structures were analyzed by fractography. The Kaplan-Meier test followed by a log-rank Mantel-Cox post hoc test was used to analyze FFL and CFF (α=.05). Weibull analysis was also performed. RESULTS: The round (1065 N) and trapezoid (1010 N) groups presented higher FFL values than the square one (870 N) (P≤.05). For CFF, the round connector (358 777) was better than the square (280 310) (P=.006), and the trapezoid (337 773) was statistically similar to both (P>.05). No difference among groups was observed in Weibull modulus either for CFF or FFL data. All failures were catastrophic, originating at the base of the connector and propagating toward the occlusal surface of the pontic (region under loading). CONCLUSIONS: The connector cross-sectional geometry significantly influenced the mechanical fatigue performance of implant-supported fixed partial prostheses made of monolithic zirconia.

Could different direct restoration techniques affect interfacial gap and fracture resistance of endodontically treated anterior teeth?

OBJECTIVES: To evaluate different direct restoration techniques on various cavity designs in anterior endodontically treated teeth (ETT). MATERIALS AND METHODS: Ninety upper central incisors (n = 90) were selected, endodontically treated, and divided into three groups (n = 30) accordingly to the cavity design: minimal endodontic cavity access (group A), endodontic access + mesial class III cavity (group B), and endodontic access + two class III cavities (group C). Three subgroups (n = 10) were then created accordingly to the restoration technique: nano hybrid composite restoration (subgroup a), glass fiber post + dual-cure luting cement (subgroup b), and bundled glass fiber + dual-cure luting cement (subgroup c). Samples underwent micro-CT scan, chewing simulation, and a second micro-CT scan. 3D quantification (mm3) of interfacial gap progression was performed; then, samples underwent fracture resistance test. Data were statistically analyzed setting significance at p < 0.05. RESULTS: Groups A and B showed significantly lower interfacial gap progression compared with group C. Subgroup b performed significantly better compared with subgroups a and c. Improved fracture strength was reported for group C compared with group A, while both subgroups b and c performed better than subgroup a. CONCLUSIONS: Cavity design significantly influenced interfacial gap progression and fracture resistance. Fiber posts significantly lowered gap progression and improved fracture resistance while bundled fibers only increased fracture resistance. A significant reduction of non-repairable fractures was recorded when fibers were applied. CLINICAL RELEVANCE: A minimally invasive approach, conserving marginal crests, should be applied whenever possible. Inserting a fiber post is indicated when restoring anterior ETT, in order to reduce gap progression, improve fracture resistance, and avoid catastrophic failures.