Optimization Conditions of Malachite Green Adsorption onto Almond Shell Carbon Waste Using Process Design.

Almond shell-based biocarbon is a cheap adsorbent for the removal of malachite green, which has been investigated in this work. FT-IR, DRX, and BET were used to characterize almond shell-based biocarbon. The nitrogen adsorption-desorption isotherms analysis results showed a surface area of 120.21 m2/g and a type H4 adsorption isotherm. The parameters of initial dye concentration (5-600 mg.L-1), adsorbent mass (0.1-0.6 mg), and temperature (298-373 K) of adsorption were investigated. The experiments showed that the almond shell could be used in a wide concentration and temperature range. The adsorption study was fitted to the Langmuir isotherm and the pseudo-second-order kinetic model. The results of the FT-IR analysis demonstrated strong agreement with the pseudo-second-order chemisorption process description. The maximum adsorption capacity was calculated from the Langmuir isotherm and evaluated to be 166.66 mg.g-1. The positive ∆H (12.19 J.mol-1) indicates that the adsorption process is endothermic. Almond shell was found to be a stable adsorbent. Three different statistical design sets of experiments were taken out to determine the best conditions for the batch adsorption process. The optimal conditions for MG uptake were found to be adsorbent mass (m = 0.1 g), initial dye concentration (C0 = 600 mg.L-1), and temperature (T = 25 °C). The analysis using the D-optimal design showed that the model obtained was important and significant, with an R2 of 0.998.

Magnetic Carbon Nanofiber Mats for Prospective Single Photon Avalanche Diode (SPAD) Sensing Applications.

Electrospinning enables simple and cost-effective production of magnetic nanofibers by adding nanoparticles to a polymer solution. In order to increase the electrical conductivity of such nanofibers, the carbonization process is crucial. In this study, the chemical and morphological properties of magnetic nanofiber mats prepared from polyacrylonitrile (PAN)/magnetite were investigated. In our previous studies, PAN/magnetite nanofiber mats were carbonized at 500 °C, 600 °C, and 800 °C. Here, PAN/magnetite nanofiber mats were carbonized at 1000 °C. The surface morphology of these PAN/magnetite nanofiber mats is not significantly different from nanofiber mats thermally treated at 800 °C and have remained relatively flexible at 1000 °C, which can be advantageous for various application fields. The addition of nanoparticles increased the average fiber diameter compared to pure PAN nanofiber mats and improved the dimensional stability during thermal processes. The high conductivity, the high magnetization properties, as well as shielding against electromagnetic interference of such carbonized nanofibers can be proposed for use in single photon avalanche diode (SPAD), where these properties are advantageous.

Nonclassical Attack on a Quantum Key Distribution System.

The article is focused on research of an attack on the quantum key distribution system and proposes a countermeasure method. Particularly noteworthy is that this is not a classic attack on a quantum protocol. We describe an attack on the process of calibration. Results of the research show that quantum key distribution systems have vulnerabilities not only in the protocols, but also in other vital system components. The described type of attack does not affect the cryptographic strength of the received keys and does not point to the vulnerability of the quantum key distribution protocol. We also propose a method for autocompensating optical communication system development, which protects synchronization from unauthorized access. The proposed method is based on the use of sync pulses attenuated to a photon level in the process of detecting a time interval with a signal. The paper presents the results of experimental studies that show the discrepancies between the theoretical and real parameters of the system. The obtained data allow the length of the quantum channel to be calculated with high accuracy.

Investigation of Hybrid Electrodes of Polyaniline and Reduced Graphene Oxide with Bio-Waste-Derived Activated Carbon for Supercapacitor Applications.

Graphene-based materials have been widely studied in the field of supercapacitors. However, their electrochemical properties and applications are still restricted by the susceptibility of graphene-based materials to curling and agglomeration during production. This study introduces a facile method for synthesizing reduced graphene oxide (rGO) nanosheets and activated carbon based on olive stones (OS) with polyaniline (PAni) surface decoration for the development of supercapacitors. Several advanced techniques were used to examine the structural properties of the samples. The obtained PAni@OS-rGO (1:1) electrode exhibits a high electrochemical capacity of 582.6 F·g-1 at a current density of 0.1 A·g-1, and an energy density of 26.82 Wh·kg-1; thus, it demonstrates potential for efficacious energy storage. In addition, this electrode material exhibits remarkable cycling stability, retaining over 90.07% capacitance loss after 3000 cycles, indicating a promising long cycle life. Overall, this research highlights the potential of biomass-derived OS in the presence of PAni and rGO to advance the development of high-performance supercapacitors.

Algae-Based Biopolymers for Batteries and Biofuel Applications in Comparison with Bacterial Biopolymers-A Review.

Algae-based biopolymers can be used in diverse energy-related applications, such as separators and polymer electrolytes in batteries and fuel cells and also as microalgal biofuel, which is regarded as a highly renewable energy source. For these purposes, different physical, thermochemical, and biochemical properties are necessary, which are discussed within this review, such as porosity, high temperature resistance, or good mechanical properties for batteries and high energy density and abundance of the base materials in case of biofuel, along with the environmental aspects of using algae-based biopolymers in these applications. On the other hand, bacterial biopolymers are also often used in batteries as bacterial cellulose separators or as biopolymer network binders, besides their potential use as polymer electrolytes. In addition, they are also regarded as potential sustainable biofuel producers and converters. This review aims at comparing biopolymers from both aforementioned sources for energy conversion and storage. Challenges regarding the production of algal biopolymers include low scalability and low cost-effectiveness, and for bacterial polymers, slow growth rates and non-optimal fermentation processes often cause challenges. On the other hand, environmental benefits in comparison with conventional polymers and the better biodegradability are large advantages of these biopolymers, which suggest further research to make their production more economical.

Electrospun Magnetic Nanofiber Mats for Magnetic Hyperthermia in Cancer Treatment Applications-Technology, Mechanism, and Materials.

The number of cancer patients is rapidly increasing worldwide. Among the leading causes of human death, cancer can be regarded as one of the major threats to humans. Although many new cancer treatment procedures such as chemotherapy, radiotherapy, and surgical methods are nowadays being developed and used for testing purposes, results show limited efficiency and high toxicity, even if they have the potential to damage cancer cells in the process. In contrast, magnetic hyperthermia is a field that originated from the use of magnetic nanomaterials, which, due to their magnetic properties and other characteristics, are used in many clinical trials as one of the solutions for cancer treatment. Magnetic nanomaterials can increase the temperature of nanoparticles located in tumor tissue by applying an alternating magnetic field. A very simple, inexpensive, and environmentally friendly method is the fabrication of various types of functional nanostructures by adding magnetic additives to the spinning solution in the electrospinning process, which can overcome the limitations of this challenging treatment process. Here, we review recently developed electrospun magnetic nanofiber mats and magnetic nanomaterials that support magnetic hyperthermia therapy, targeted drug delivery, diagnostic and therapeutic tools, and techniques for cancer treatment.

A Recent Review of Electrospun Porous Carbon Nanofiber Mats for Energy Storage and Generation Applications.

Electrospun porous carbon nanofiber mats have excellent properties, such as a large surface area, tunable porosity, and excellent electrical conductivity, and have attracted great attention in energy storage and power generation applications. Moreover, due to their exceptional properties, they can be used in dye-sensitized solar cells (DSSCs), membrane electrodes for fuel cells, catalytic applications such as oxygen reduction reactions (ORRs), hydrogen evolution reactions (HERs), and oxygen evolution reactions (OERs), and sensing applications such as biosensors, electrochemical sensors, and chemical sensors, providing a comprehensive insight into energy storage development and applications. This study focuses on the role of electrospun porous carbon nanofiber mats in improving energy storage and generation and contributes to a better understanding of the fabrication process of electrospun porous carbon nanofiber mats. In addition, a comprehensive review of various alternative preparation methods covering a wide range from natural polymers to synthetic carbon-rich materials is provided, along with insights into the current literature.

Measuring Physical Properties of Electrospun Nanofiber Mats for Different Biomedical Applications.

Electrospun nanofiber mats are nowadays often used for biotechnological and biomedical applications, such as wound healing or tissue engineering. While most studies concentrate on their chemical and biochemical properties, the physical properties are often measured without long explanations regarding the chosen methods. Here, we give an overview of typical measurements of topological features such as porosity, pore size, fiber diameter and orientation, hydrophobic/hydrophilic properties and water uptake, mechanical and electrical properties as well as water vapor and air permeability. Besides describing typically used methods with potential modifications, we suggest some low-cost methods as alternatives in cases where special equipment is not available.

Suitability of Mycelium-Reinforced Nanofiber Mats for Filtration of Different Dyes.

Electrospun nanofiber mats have a high specific surface area and very small pores which can be tailored by the spinning process. They are thus highly suitable as filters for small particles and molecules, such as organic dyes. On the other hand, they are usually very thin and thus have low mechanical properties. As a potential reinforcement, mycelium of Pleurotus ostreatus was grown on poly(acrylonitrile) nanofiber mats and thermally solidified after fully covering the nanofiber mats. This study investigates whether the filtration efficiency of the nanofiber mats is altered by the mycelium growing through it and whether the mechanical properties of the nanofibrous filters can be improved in this way. The study shows fast and reliable growth of the mycelium on the nanofiber mats and high filtration efficiency for astra blue and chlorophyll, while indigo carmine showed only very low filtration efficiency of up to 20%. For chlorophyll and safranin, membranes with mycelium showed higher filtration than pure nanofiber mats. In diffusion cell tests, especially astra blue was strongly adsorbed on the membranes with mycelium.

New Hybrid Adsorbents Based on Polyaniline and Polypyrrole with Silicon Dioxide: Synthesis, Characterization, Kinetics, Equilibrium, and Thermodynamic Studies for the Removal of 2,4-Dichlorophenol.

In the current study, polyaniline and polypyrrole with silicon dioxide (PAni:PPy@SiO2) were combined to formulate a new adsorbent, which was examined using XRD, TEM, SEM, FTIR, TGA, and BET, and the adsorption kinetics were investigated by UV-vis spectroscopy. The optical band gap was also evaluated. The electrochemical behavior was investigated using cyclic voltammograms. Moreover, experimental conditions were used to evaluate the 2,4-dichlorophenol (2,4-DCP) adsorption based on the pH, temperature, reaction time, and initial concentration. The analytical isotherm data were determined by Langmuir, Freundlich, Temkin, Sips, and Redlich-Peterson models. For the analysis of the kinetic data, the pseudo-first- and -second-order models and the intraparticle diffusion model were investigated. It was found that this new adsorbent possessed the highest adsorption efficiency after several regeneration cycles. Furthermore, the thermodynamic parameters of adsorption, such as entropy (ΔS), enthalpy (ΔH), and standard Gibbs were measured. These results suggest that the PAni:PPy backbone can generally be better applied for the elimination of 2,4-dichlorophenol by appropriately dispersing it over the surface of suitable SiO2. This search provides a novel way to develop separable, high-performance adsorbents for adsorbing organic contamination from wastewater.

Adsorption of Methylene Blue Dye by Cetyltrimethylammonium Bromide Intercalated Polyaniline-Functionalized Montmorillonite Clay Nanocomposite: Kinetics, Isotherms, and Mechanism Study.

In this study, new adsorbents were prepared by modifying a montmorillonite clay (Mt) with cethyltrimethyl ammonium bromide (CTAB) to form CTAB-Mt, followed by a second modification process with polyaniline (PAni) to form PAni@CTAB-Mt by in situ polymerization of aniline. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), transmission electron microscopy (TEM), cyclic voltammetry (CV) and the Brunauer-Emmett-Teller (BET) technique were used to characterize the samples. These adsorbents were used in a batch process to remove methylene blue (MB) from aqueous solution. Factors investigated included initial pH of the solution, contact time and temperature. The adsorption data fit the Freundlich isotherm better than the Langmuir and Temkin isotherms. The maximum adsorption capacities (qeq) obtained were 108.82 mg·g-1, 71.20 mg·g-1 and 57.36 mg·g-1 for PAni@CTAB-Mt, CTAB-Mt and Mt, respectively. The enhanced adsorption capability of the hybrid material is due to increase in surface area and pore volume of the PAni@CTAB-Mt adsorbent. The adsorption results were found to fit well with the pseudo-second-order kinetics model, with highest correlation coefficient (R2) values of 0.954, 0.942 and 0.958 for Mt, CTAB-Mt and PAni@CTAB-Mt adsorbents, respectively. The pH and temperature had a significant effect on the adsorption process, and the negative values of ΔG suggest that the adsorption process was spontaneous and feasible. The desorption and reusability experiment indicated that PAni@CTAB-Mt has the potential to be a reusable adsorbent for MB removal.

Electrospinning of Magnetite-Polyacrylonitrile Composites for the Production of Oxygen Reduction Reaction Catalysts.

In this study, electrospun carbon fiber electrodes were prepared by the carbonization of PAN-Fe3O4 electrospun fibers at 800 °C for their use as catalysts in the oxygen reduction reaction in an alkaline electrolyte. Magnetic nanofiber mats were fabricated using a needle-free electrospinning method by incorporating magnetic nanoparticles into a polymer solution. Electrochemical tests revealed that the oxygen reduction reaction (ORR) activity is optimized at an intermediate magnetite loading of 30% wt. These catalysts not only show better performance compared to their counterparts but also achieve high selectivity to water at low potentials. The onset and half-wave potentials of 0.92 and 0.76 V shown by these samples are only slightly behind those of the commercial Pt 20%-carbon black ORR catalyst. The obtained results point out that the electrospinning of PAN-Fe3O4 solutions allows the preparation of advanced N-Fe ORR catalysts in fibrillar morphology.

Electrospinning Nanofiber Mats with Magnetite Nanoparticles Using Various Needle-Based Techniques.

Electrospinning can be used to produce nanofiber mats containing diverse nanoparticles for various purposes. Magnetic nanoparticles, such as magnetite (Fe3O4), can be introduced to produce magnetic nanofiber mats, e.g., for hyperthermia applications, but also for basic research of diluted magnetic systems. As the number of nanoparticles increases, however, the morphology and the mechanical properties of the nanofiber mats decrease, so that freestanding composite nanofiber mats with a high content of nanoparticles are hard to produce. Here we report on poly (acrylonitrile) (PAN) composite nanofiber mats, electrospun by a needle-based system, containing 50 wt% magnetite nanoparticles overall or in the shell of core-shell fibers, collected on a flat or a rotating collector. While the first nanofiber mats show an irregular morphology, the latter are quite regular and contain straight fibers without many beads or agglomerations. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) reveal agglomerations around the pure composite nanofibers and even, round core-shell fibers, the latter showing slightly increased fiber diameters. Energy dispersive X-ray spectroscopy (EDS) shows a regular distribution of the embedded magnetic nanoparticles. Dynamic mechanical analysis (DMA) reveals that mechanical properties are reduced as compared to nanofiber mats with smaller amounts of magnetic nanoparticles, but mats with 50 wt% magnetite are still freestanding.

Facile Synthesis and Electrochemical Characterization of Polyaniline@TiO2-CuO Ternary Composite as Electrodes for Supercapacitor Applications.

This research reports the facile, controlled, low-cost fabrication, and evaluation of properties of polyaniline matrix deposited on titanium dioxide and copper(II) oxide ternary-composite (PANI@TiO2-CuO)-based electrode material for supercapacitor application. The process involves the preparation of CuO in the presence of TiO2 to form TiO2-CuO by a facile method, followed by in-situ oxidative polymerization of aniline monomer. The structural and physical properties were evaluated based on the results of FTIR spectroscopy, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), transmission electron (TEM) and scanning electron (SEM) microscopy, thermogravimetric analysis (TGA), and BET surface areas analysis. The results indicated that TiO2-CuO was dispersed uniformly in the PANI matrix. Owing to such dispersion of TiO2-CuO, the PANI@TiO2-CuO material exhibits dramatic improvements on thermal stability in comparison with the pure PANI. The cyclic voltammetry (CV) confirms the reversibility of PANI redox transitions for this optimized electrode material. Moreover, the results reveal that the specific capacitance of PANI@TiO2-CuO reaches 87.5% retention after 1500 cycles under 1.0 A g-1, with a better charge storage performance as compared to pure PANI and PANI@TiO2 electrodes. The preparation of PANI@TiO2-CuO with enhanced electrochemical properties provides a feasible route for promoting its applications in supercapacitors.

Development, Investigation, and Comparative Study of the Effects of Various Metal Oxides on Optical Electrochemical Properties Using a Doped PANI Matrix.

A comparative study was performed in order to analyze the effect of metal oxide (MO) on the properties of a polymeric matrix. In this study, polyaniline (PANI)@Al2O3, PANI@TiC, and PANI@TiO2 nanocomposites were synthesized using in situ polymerization with ammonium persulfate as an oxidant. The prepared materials were characterized by various analytical methods such as X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), thermogravimetric analysis (TGA), UV/visible (UV/Vis) spectroscopy, Fourier-transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM). Furthermore, the conductive properties of the materials were tested using the four-point probe method. The presence of MO in the final product was confirmed by XPS, XRD, FTIR, and TEM, while spectroscopic characterization revealed interactions between the MOs and PANI. The results showed that the thermal stability was improved when the MO was incorporated into the polymeric matrix. Moreover, the results revealed that incorporating TiO2 into the PANI matrix improves the optical bandgap of the nanocomposite and decreases electrical conductivity compared to other conducting materials. Furthermore, the electrochemical properties of the hybrid nanocomposites were tested by cyclic voltammetry (CV) and galvanostatic charge/discharge (GCD). The obtained results suggest that the PANI@TiO2 nanocomposite could be a promising electrode material candidate for high-performance supercapacitor applications.

Electrospun Carbon Nanofibers from Biomass and Biomass Blends-Current Trends.

In recent years, ecological issues have led to the search for new green materials from biomass as precursors for producing carbon materials (CNFs). Such green materials are more attractive than traditional petroleum-based materials, which are environmentally harmful and non-biodegradable. Biomass could be ideal precursors for nanofibers since they stem from renewable sources and are low-cost. Recently, many authors have focused intensively on nanofibers' production from biomass using microwave-assisted pyrolysis, hydrothermal treatment, ultrasonication method, but only a few on electrospinning methods. Moreover, still few studies deal with the production of electrospun carbon nanofibers from biomass. This review focuses on the new developments and trends of electrospun carbon nanofibers from biomass and aims to fill this research gap. The review is focusing on recollecting the most recent investigations about the preparation of carbon nanofiber from biomass and biopolymers as precursors using electrospinning as the manufacturing method, and the most important applications, such as energy storage that include fuel cells, electrochemical batteries and supercapacitors, as well as wastewater treatment, CO2 capture, and medicine.

Electrospun Nanofiber Mats for Filtering Applications-Technology, Structure and Materials.

Air pollution is one of the biggest health and environmental problems in the world and a huge threat to human health on a global scale. Due to the great impact of respiratory viral infections, chronic obstructive pulmonary disease, lung cancer, asthma, bronchitis, emphysema, lung disease, and heart disease, respiratory allergies are increasing significantly every year. Because of the special properties of electrospun nanofiber mats, e.g., large surface-to-volume ratio and low basis weight, uniform size, and nanoporous structure, nanofiber mats are the preferred choice for use in large-scale air filtration applications. In this review, we summarize the significant studies on electrospun nanofiber mats for filtration applications, present the electrospinning technology, show the structure and mechanism of air filtration. In addition, an overview of current air filtration materials derived from bio- and synthetic polymers and blends is provided. Apart from this, the use of biopolymers in filtration applications is still relatively new and this field is still under-researched. The application areas of air filtration materials are discussed here and future prospects are summarized in conclusion. In order to develop new effective filtration materials, it is necessary to understand the interaction between technology, materials, and filtration mechanisms, and this study was intended to contribute to this effort.

The Possibility of Reuse of Nanofiber Mats by Machine Washing at Different Temperatures.

The worldwide spread of coronavirus COVID-19 infections demonstrates the great need for personal protective equipment and, in particular, hygiene masks. These masks are essential for the primary protection of the respiratory tract against pathogens such as viruses and bacteria that are infectious and transmitted through the air as large droplets or via small airborne particles. The use of protective masks will continue to accompany humans for an indefinite period of time, and therefore there is an urgent need for a safe method to extend their usability by reusing them under perspective with minimal loss of protective properties. Nanofiber mats are widely used in masks and in this study the reusability of nanofiber mats is investigated by washing them at different temperatures. This paper shows the first measurements of the washability of nanofiber mats. Furthermore, the air permeability is measured, and the evaporation resistance is evaluated. According to the results of this study, the air permeability performance of nanofiber mats does not change significantly after washing, confirming the possibility of reuse.

Magnetic Properties of Electrospun Magnetic Nanofiber Mats after Stabilization and Carbonization.

Magnetic nanofibers are of great interest in basic research, as well as for possible applications in spintronics and neuromorphic computing. Here we report on the preparation of magnetic nanofiber mats by electrospinning polyacrylonitrile (PAN)/nanoparticle solutions, creating a network of arbitrarily oriented nanofibers with a high aspect ratio. Since PAN is a typical precursor for carbon, the magnetic nanofiber mats were stabilized and carbonized after electrospinning. The magnetic properties of nanofiber mats containing magnetite or nickel ferrite nanoparticles were found to depend on the nanoparticle diameters and the potential after-treatment, as compared with raw nanofiber mats. Micromagnetic simulations underlined the different properties of both magnetic materials. Atomic force microscopy and scanning electron microscopy images revealed nearly unchanged morphologies after stabilization without mechanical fixation, which is in strong contrast to pure PAN nanofiber mats. While carbonization at 500 °C left the morphology unaltered, as compared with the stabilized samples, stronger connections between adjacent fibers were formed during carbonization at 800 °C, which may be supportive of magnetic data transmission.

Chemical and Morphological Transition of Poly(acrylonitrile)/Poly(vinylidene Fluoride) Blend Nanofibers during Oxidative Stabilization and Incipient Carbonization.

Thermally stabilized and subsequently carbonized nanofibers are a promising material for many technical applications in fields such as tissue engineering or energy storage. They can be obtained from a variety of different polymer precursors via electrospinning. While some methods have been tested for post-carbonization doping of nanofibers with the desired ingredients, very little is known about carbonization of blend nanofibers from two or more polymeric precursors. In this paper, we report on the preparation, thermal treatment and resulting properties of poly(acrylonitrile) (PAN)/poly(vinylidene fluoride) (PVDF) blend nanofibers produced by wire-based electrospinning of binary polymer solutions. Using a wide variety of spectroscopic, microscopic and thermal characterization methods, the chemical and morphological transition during oxidative stabilization (280 °C) and incipient carbonization (500 °C) was thoroughly investigated. Both PAN and PVDF precursor polymers were detected and analyzed qualitatively and quantitatively during all stages of thermal treatment. Compared to pure PAN nanofibers, the blend nanofibers showed increased fiber diameters, strong reduction of undesired morphological changes during oxidative stabilization and increased conductivity after carbonization.