A universal interface for plug-and-play assembly of stretchable devices.

Stretchable hybrid devices have enabled high-fidelity implantable1-3 and on-skin4-6 monitoring of physiological signals. These devices typically contain soft modules that match the mechanical requirements in humans7,8 and soft robots9,10, rigid modules containing Si-based microelectronics11,12 and protective encapsulation modules13,14. To make such a system mechanically compliant, the interconnects between the modules need to tolerate stress concentration that may limit their stretching and ultimately cause debonding failure15-17. Here, we report a universal interface that can reliably connect soft, rigid and encapsulation modules together to form robust and highly stretchable devices in a plug-and-play manner. The interface, consisting of interpenetrating polymer and metal nanostructures, connects modules by simply pressing without using pastes. Its formation is depicted by a biphasic network growth model. Soft-soft modules joined by this interface achieved 600% and 180% mechanical and electrical stretchability, respectively. Soft and rigid modules can also be electrically connected using the above interface. Encapsulation on soft modules with this interface is strongly adhesive with an interfacial toughness of 0.24 N mm-1. As a proof of concept, we use this interface to assemble stretchable devices for in vivo neuromodulation and on-skin electromyography, with high signal quality and mechanical resistance. We expect such a plug-and-play interface to simplify and accelerate the development of on-skin and implantable stretchable devices.

Understanding the Mechanisms of Methylammonium-Induced Thermal Instability in Mixed-FAMA Perovskites.

Despite a recent shift toward methylammonium (MA)-free lead-halide perovskites for perovskite solar cells, high-efficiency formamidinium lead iodide (FAPbI3) devices still often require methylammonium chloride (MACl) as an additive, which evaporates away during the annealing process. In this article, it is shown that the residual MA+, however, triggers thermal instability. To investigate the possibility of an optimal concentration of MA+ that may improve thermal stability, the intrinsic thermal stability of pure FA, FA-rich, MA-rich, and pure MA perovskite films (FA1-xMAxPbI3, FAMA) is studied. The results show that the thermal stability of FAMA perovskites decreases with more MA+, under degradation conditions that isolate the intrinsic thermal stability of the material (i.e., without moisture and oxygen effects). X-ray diffraction (XRD), proton-transfer-reaction time-of-flight mass spectrometry (PTR-ToF-MS), photoluminescence (PL) and UV-visible spectroscopy, and depth-profiling X-ray Photoelectron Spectroscopy (XPS) are employed to show that the observed trend is mainly due to the decomposition of the MA+ cation, as opposed to other effects such as the precursor solvent and film morphologies. It is also found that the surfaces of these FAMA films are MA+ rich, although this phenomenon does not appear to affect thermal stability. Finally, it is demonstrated that this trend is unaffected by the presence of Spiro-OMeTAD atop the film, and thus solar cell devices should preserve this trend.

Elucidation of the synergistic effects of 3d metal (M = Cu, Co, and Ni) dopants and terminations (T = -O- and -OH) of Ti3C2Tx MXenes for urea adsorption ability via DFT calculations and experiments.

Dialysis is an artificial process to remove excess urea toxins from the body through adsorption or conversion. Urea adsorption by emergent 2D materials such as MXenes is one probable approach. Based on density functional theory (DFT) studies, the surface of Ti3C2Tx (T = -O- and -OH) MXenes is not optimum for urea adsorption. Therefore, functionalization with 3d metal dopants (Cu, Co, and Ni) is proposed to improve their urea adsorption ability. DFT calculations indicate that oxygen-terminated Ti3C2O2 has a much better urea adsorption ability when doped with Cu, Co, and Ni, with adsorption energy (Eads) values of -2.11 eV, -1.90 eV and -1.72 eV, respectively. These adsorption energies are much more favourable than that of the undoped one (Eads = -0.52 eV). To verify the calculation results, MILD Ti3C2Tx, or MXenes synthesized via the safer and easier minimally intensive layer delamination (MILD) method, were utilized to simulate Ti3C2O2 since they have -O- termination as the dominant species. Experimentally, the adsorption studies found that low concentration of Cu, Co, and Ni on MILD Ti3C2Tx showed a urea removal efficiency of 21.9%, 6.0% and 0.2%, respectively, much better than 0% removal efficiency of unfunctionalized Ti3C2Tx. Therefore, both DFT calculations and experiments showed that various metal functionalized MXenes have a similar trend for urea adsorption, highlighting the feasibility of using the computational approach to predict urea adsorption and further opening a new promising direction for the urea adsorption. Finally, this study is also the first to examine synergistic effects of metal dopants and surface terminations on MXenes for urea adsorption.

Tuning Electronic Structure and Composition of FeNi Nanoalloys for Enhanced Oxygen Evolution Electrocatalysis via a General Synthesis Strategy.

Developing low-cost and efficient oxygen evolution electrocatalysts is key to decarbonization. A facile, surfactant-free, and gram-level biomass-assisted fast heating and cooling synthesis method is reported for synthesizing a series of carbon-encapsulated dense and uniform FeNi nanoalloys with a single-phase face-centered-cubic solid-solution crystalline structure and an average particle size of sub-5 nm. This method also enables precise control of both size and composition. Electrochemical measurements show that among Fex Ni(1- x ) nanoalloys, Fe0.5 Ni0.5 has the best performance. Density functional theory calculations support the experimental findings and reveal that the optimally positioned d-band center of O-covered Fe0.5 Ni0.5 renders a half-filled antibonding state, resulting in moderate binding energies of key reaction intermediates. By increasing the total metal content from 25 to 60 wt%, the 60% Fe0.5 Ni0.5 /40% C shows an extraordinarily low overpotential of 219 mV at 10 mA cm-2 with a small Tafel slope of 23.2 mV dec-1 for the oxygen evolution reaction, which are much lower than most other FeNi-based electrocatalysts and even the state-of-the-art RuO2 . It also shows robust durability in an alkaline environment for at least 50 h. The gram-level fast heating and cooling synthesis method is extendable to a wide range of binary, ternary, quaternary nanoalloys, as well as quinary and denary high-entropy-alloy nanoparticles.

Correlation between blend morphology and recombination dynamics in additive-added P3HT:PCBM solar cells.

The addition of a small amount of high boiling point solvent in organic donor/acceptor blends to control their morphology is a viable approach to enhance the power conversion efficiency of bulk heterojunction (BHJ) organic solar cells. Herein, through transient absorption spectroscopy (TAS) correlated with physical characterizations and device studies, we investigate the effects of a family of thiol-based additives (i.e., 1,5-pentanedithiol (PDT), 1,6-hexanedithiol (HDT) and 1,8-octanedithiol (ODT)) in P3HT:PCBM blend films in a bid to establish a morphology-function-charge dynamics relationship with their photovoltaic performances. The performance of solar cell devices (ηHDT = 2.8%, ηODT = 2.8%, ηPDT = 1.7%) is related to the additive-induced phase separation and the degree of ordering of P3HT. TAS uncovers a more efficient initial exciton and polaron generation in the additive-treated blend samples compared to the non-additive treated control sample. HDT and ODT-added blends exhibit decay dynamics and performances similar to those of the thermally annealed samples. However, the PDT-added blend exhibits a strong trap-assisted recombination in the subsequent nanosecond-microsecond timescales. We attribute this to the loss of charge carriers in the larger isolated P3HT domains due to the lack of percolation paths to the electrode. Our findings illustrate that understanding the complex interplay of the crystalline order, intermixed phases and percolation pathways is key to optimizing the performance of thermal-annealing free, additive-treated organic solar cells.

Polymer nanofibers: preserving nanomorphology in ternary blend organic photovoltaics.

The morphology of donor-acceptor blends holds the key to good performance through the balancing of good exciton dissociation efficiency and interconnectivity for good charge collection. In this work, the good morphology is preserved in ternary blend systems through the use of poly(3-hexylthiophene) (P3HT) nanofibers. The iridium(III)-based metal complex is incorporated in P3HT-PCBM blends as a triplet exciton sensitizer in the bulk heterojunction (BHJ) organic photovoltaics (OPV). The devices using triplet-sensitized ternary blends of P3HT experience a significant degradation in performance, a tendency further aggravated by thermal treatment. This is due to disruption in the morphology thus affecting charge generation and collection. In order to overcome these morphological issues and to circumvent the restriction due to the crystallization of the polymers, here we demonstrate the use of pre-assembled nanofibers in these ternary blends. The concept of stabilizing the nanomorphology of the blend material through the use of nanofibers can also be applied to other ternary systems.

Functionalized sp2 Carbon-Conjugated Covalent Organic Frameworks for Interfacial Modulation of Inverted Perovskite Solar Cells.

Interfacial modulation utilizing functional materials is proven to be crucial for obtaining high photovoltaic performance in lead halide perovskite solar cells (PSCs). This study investigates, for the first time, the utilization of a pyrene-based sp2 carbon-conjugated covalent organic framework (sp2c-COF) as an interfacial layer in inverted PSCs. Functionalized with cyano (-CN) Lewis base groups, the sp2c-COF exhibits a dual effect, simultaneously passivating both the NiOx and the perovskite layers. Detailed characterization results highlight the role of sp2c-COF in reducing the Ni3+ defect density in NiOx films and forming Lewis acid-base adducts with undercoordinated Pb2+ on the perovskite surfaces, thereby inhibiting interfacial redox reactions and suppressing non-radiative recombination. Moreover, sp2c-COF leads to improved crystallinity of perovskite films. Benefiting from the synergistic effects, sp2c-COF-modified devices delivered a champion efficiency of 17.64%. These findings underscore the potential of sp2c-COF as a functional interface material for PSCs, offering enhanced efficiency and stability. The study contributes to advancing the understanding and application of covalent organic frameworks in photovoltaic technologies.

Operando Electrodeposition of Nonprecious Metal Copper Nanocatalysts on Low-Dimensional Support Materials for Nitrate Reduction Reactions.

Supported nonprecious metal catalysts such as copper (Cu) are promising replacements for Pt-based catalysts for a wide range of energy-related electrochemical reactions. Direct electrochemical deposition is one of the most straightforward and versatile methods to synthesize supported nonprecious metal catalysts. However, further advancement in the design of supported nonprecious metal catalysts requires a detailed mechanistic understanding of the interplay between kinetics and thermodynamics of the deposition phenomena under realistic reaction conditions. Here, we study the electrodeposition of Cu on carbon nanotubes and graphene derivatives under electrochemical conditions using in situ liquid cell transmission electron microscopy (TEM). By combining real-time imaging, electrochemical measurements, X-ray photoelectron spectroscopy (XPS), and finite-element analysis (FEA), we show that low-dimensional support materials, especially carbon nanotubes, are excellent for generating uniform and finely dispersed platinum group metal-(PGM)-free catalysts under mild electrochemical conditions. The electrodeposited Cu on graphene and carbon nanotubes is also observed to show good electrochemical activity toward nitrate reduction reactions (NO3RRs), further supported by density functional theory (DFT) calculations. Nitrogen doping plays an important role in guiding nonprecious metal deposition, but its low electrical conductivity may give rise to lower NO3RR activity compared to its nondoped analogue. The development of supported nonprecious metals through interfacial and surface engineering for the design of supported catalysts will substantially reduce the demand for precious metals and generate robust catalysts with better durability, thereby presenting opportunities for solving the critical problems in energy storage and electrocatalysis.

Flexible Wet-Spun PEDOT:PSS Microfibers Integrating Thermal-Sensing and Joule Heating Functions for Smart Textiles.

Multifunctional fiber materials play a key role in the field of smart textiles. Temperature sensing and active thermal management are two important functions of smart fabrics, but few studies have combined both functions in a single fiber material. In this work, we demonstrate a temperature-sensing and in situ heating functionalized conductive polymer microfiber by exploiting its high electrical conductivity and thermoelectric properties. The conductive polymer microfibers were prepared by wet-spinning the PEDOT:PSS aqueous dispersion with ionic liquid additives, which was used to enhance the electrical and mechanical properties of the final microfibers. The thermoelectric properties of these microfibers were further studied. Due to their excellent flexibility and mechanical properties, these fibers can be easily integrated into commercial fabrics for the manufacture of smart textiles through knitting. We further demonstrated a smart glove with integrated temperature-sensing and in situ heating functions, and further explored thermoelectric fiber-based temperature-sensing array fabric. These works combine the thermoelectric properties and heating function of conductive polymer fibers, providing new insights that enable further development of high-performance, multifunctional wearable smart textiles.

Effect of Air Exposure on Electron-Beam-Induced Degradation of Perovskite Films.

Organic-inorganic halide perovskites are interesting candidates for solar cell and optoelectronic applications owing to their advantageous properties such as a tunable band gap, low material cost, and high charge carrier mobilities. Despite making significant progress, concerns about material stability continue to impede the commercialization of perovskite-based technology. In this article, we investigate the impact of environmental parameters on the alteration of structural properties of MAPbI3 (CH3NH3PbI3) thin films using microscopy techniques. These characterizations are performed on MAPbI3 thin films exposed to air, nitrogen, and vacuum environments, the latter being possible by using dedicated air-free transfer setups, after their fabrication into a nitrogen-filled glovebox. We observed that even less than 3 min of air exposure increases the sensitivity to electron beam deterioration and modifies the structural transformation pathway as compared to MAPbI3 thin films which are not exposed to air. Similarly, the time evolution of the optical responses and the defect formation of both air-exposed and non-air-exposed MAPbI3 thin films are measured by time-resolved photoluminescence. The formation of defects in the air-exposed MAPbI3 thin films is first observed by optical techniques at longer timescales, while structural modifications are observed by transmission electron microscopy (TEM) measurements and supported by X-ray photoelectron spectroscopy (XPS) measurements. Based on the complementarity of TEM, XPS, and time-resolved optical measurements, we propose two different degradation mechanism pathways for air-exposed and non-air-exposed MAPbI3 thin films. We find that when exposed to air, the crystalline structure of MAPbI3 shows gradual evolution from its initial tetragonal MAPbI3 structure to PbI2 through three different stages. No significant structural changes over time from the initial structure are observed for the MAPbI3 thin films which are not exposed to air.

Unveiling Charge-Transfer Dynamics at Singlet Fission Layer/Hybrid Perovskite Interface.

Singlet fission (SF) materials have been applied in various types of solar cells to pursue higher power conversion efficiency (PCE) beyond the Shockley-Queisser (SQ) limit. SF implementation in perovskite solar cells has not been successfully realized yet due to the insufficient understanding of the SF/perovskite heterojunctions. In this work, we attempt to elucidate the charge dynamics of an SF/perovskite system by incorporating a well-known SF molecule, TIPS-pentacene, and a triple-cation perovskite Cs0.05(FA0.85MA0.15)0.95PbI2.55Br0.45, owing to their well-matched energy structures. The transient absorption spectra and kinetic fitting plots suggest an electron-transfer process from the triplet state of TIPS-pentacene to perovskite in the picosecond regime, which increases the carrier density by 20% in the perovskite layer. This work confirms the existence of an electron-transfer process between the SF material and perovskite, providing a pathway to SF-enhanced perovskite solar cells.

High-Performance Semi-Transparent Perovskite Solar Cells with over 22% Visible Transparency: Pushing the Limit through MXene Interface Engineering.

Semi-transparent perovskite solar cells (ST-PSCs) have attracted enormous attention recently due to their potential in building-integrated photovoltaic. To obtain adequate average visible transmittance (AVT), a thin perovskite is commonly employed in ST-PSCs. While the thinner perovskite layer has higher transparency, its light absorption efficiency is reduced, and the device shows lower power conversion efficiency (PCE). In this work, a combination of high-quality transparent conducting layers and surface engineering using 2D-MXene results in a superior PCE. In situ high-temperature X-ray diffraction provides direct evidence that the MXene interlayer retards the perovskite crystallization process and leads to larger perovskite grains with fewer grain boundaries, which are favorable for carrier transport. The interfacial carrier recombination is decreased due to fewer defects in the perovskite. Consequently, the current density of the devices with MXene increased significantly. Also, optimized indium tin oxide provides appreciable transparency and conductivity as the top electrode. The semi-transparent device with a PCE of 14.78% and AVT of over 26.7% (400-800 nm) was successfully obtained, outperforming most reported ST-PSCs. The unencapsulated device maintained 85.58% of its original efficiency after over 1000 h under ambient conditions. This work provides a new strategy to prepare high-efficiency ST-PSCs with remarkable AVT and extended stability.

Inorganic frameworks of low-dimensional perovskites dictate the performance and stability of mixed-dimensional perovskite solar cells.

Mixed-dimensional perovskites containing mixtures of organic cations hold great promise to deliver highly stable and efficient solar cells. However, although a plethora of relatively bulky organic cations have been reported for such purposes, a fundamental understanding of the materials' structure, composition, and phase, along with their correlated effects on the corresponding optoelectronic properties and degradation mechanism remains elusive. Herein, we systematically engineer the structures of bulky organic cations to template low-dimensional perovskites with contrasting inorganic framework dimensionality, connectivity, and coordination deformation. By combining X-ray single-crystal structural analysis with depth-profiling XPS, solid-state NMR, and femtosecond transient absorption, it is revealed that not all low-dimensional species work equally well as dopants. Instead, it was found that inorganic architectures with lesser structural distortion tend to yield less disordered energetic and defect landscapes in the resulting mixed-dimensional perovskites, augmented in materials with a longer photoluminescence (PL) lifetime, higher PL quantum yield (up to 11%), improved solar cell performance and enhanced thermal stability (T80 up to 1000 h, unencapsulated). Our study highlights the importance of designing templating organic cations that yield low-dimensional materials with much less structural distortion profiles to be used as additives in stable and efficient perovskite solar cells.

Molecular Locking with All-Organic Surface Modifiers Enables Stable and Efficient Slot-Die-Coated Methyl-Ammonium-Free Perovskite Solar Modules.

The power conversion efficiency (PCE) of the state-of-the-art large-area slot-die-coated perovskite solar cells (PSCs) is now over 19%, but issues with their stability persist owing to significant intrinsic point defects and a mass of surface imperfections introduced during the fabrication process. Herein, the utilization of a hydrophobic all-organic salt is reported to modify the top surface of large-area slot-die-coated methylammonium (MA)-free halide perovskite layers. Bearing two molecules, each of which is endowed with anchoring groups capable of exhibiting secondary interactions with the perovskite surfaces, the organic salt acts as a molecular lock by effectively binding to both anion and cation vacancies, substantially enhancing the materials' intrinsic stability against different stimuli. It not only reduces the ingression of external species such as oxygen and moisture, but also suppresses the egress of volatile organic components during the thermal stability testing. The treated PSCs demonstrate efficiency of 19.28% (active area of 58.5 cm2 ) and 17.62% (aperture area of 64 cm2 ) for the corresponding mini-module. More importantly, unencapsulated slot-die-coated mini-modules incorporating the all-organic surface modifier show ≈80% efficiency retention after 7500 h (313 days) of storage under 30% relative humidity (RH). They also remarkably retain more than 90% of the initial efficiency for over 850 h while being measured continuously.

Transparent electronic and photoelectric synaptic transistors based on the combination of an InGaZnO channel and a TaOx gate dielectric.

A transparent thin film transistor (TFT) based on the combination of an InGaZnO channel and a high-κ (the dielectric constant is about 42.6) TaOx gate dielectric layer is fabricated. The TFT shows robust anticlockwise hysteresis under DC voltage sweep and synaptic behaviors (i.e., excitatory postsynaptic current, short-term memory plasticity, short-term memory to long-term memory transition, and potentiation and depression) under voltage pulse stimulus. In addition, the TFT shows high responsivity to illumination of light with various wavelengths (ultraviolet and visible light). Synaptic behaviors in response to light pulse stimuli, which could be employed in vision-based neuromorphic applications, are demonstrated. Large conductance change (Gmax/Gmin > 10) and ultra-low non-linearity (α < 0.5) of the potentiation and depression can be inspired by either gate bias pulses or photoelectric pulses with short pulse widths and small amplitudes.

Crown ether enabled enhancement of ionic-electronic properties of PEDOT:PSS.

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) based organic electrochemical transistors (OECTs) have proven to be one of the most versatile platforms for various applications including bioelectronics, neuromorphic computing and soft robotics. The use of PEDOT:PSS for OECTs originates from its ample mixed ionic-electronic conductivity, which in turn depends on the microscale phase separation and morphology of the polymer. Thus, modulation of the microstructure of PEDOT:PSS film enables us to tune the operation and device characteristics of the resulting OECT. Herein we report enhanced transconductance (20 mS), fast switching (32 µs) and stable operation (10 000 cycles) of modified PEDOT:PSS based OECTs using 15-crown-5 as an additive. Four probe measurements reveal an increased electronic conductivity of the modified PEDOT:PSS film (∼450 S cm-1) while tapping mode atomic force microscopy shows an increased phase separation. Further detailed characterization using spectroelectrochemistry, X-ray photoelectron spectroscopy (XPS) and grazing incidence wide-angle X-ray diffraction (GIWAXS) provides insight into the microstructural changes brought about by the crown ether additive that result in the desirable characteristics of the modified PEDOT:PSS film.

All-Polymer Bulk-Heterojunction Organic Electrochemical Transistors with Balanced Ionic and Electronic Transport.

The rapid development of organic electrochemical transistor (OECTs)-based circuits brings new opportunities for next-generation integrated bioelectronics. The all-polymer bulk-heterojunction (BHJ) offers an attractive, inexpensive alternative to achieve efficient ambipolar OECTs, and building blocks of logic circuits constructed from them, but have not been investigated to date. Here, the first all-polymer BHJ-based OECTs are reported, consisting of a blend of new p-type ladder conjugated polymer and a state-of-the-art n-type ladder polymer. The whole ladder-type polymer BHJ also proves that side chains are not necessary for good ion transport. Instead, the polymer nanostructures play a critical role in the ion penetration and transportation and thus in the device performance. It also provides a facile strategy and simplifies the fabrication process, forgoing the need to pattern multiple active layers. In addition, the development of complementary metal-oxide-semiconductor (CMOS)-like OECTs allows the pursuit of advanced functional logic circuitry, including inverters and NAND gates, as well as for amplifying electrophysiology signals. This work opens a new approach to the design of new materials for OECTs and will contribute to the development of organic heterojunctions for ambipolar OECTs toward high-performing logic circuits.

Temperature-Dependent Coherent Tunneling across Graphene-Ferritin Biomolecular Junctions.

Understanding the mechanisms of charge transport (CT) across biomolecules in solid-state devices is imperative to realize biomolecular electronic devices in a predictive manner. Although it is well-accepted that biomolecule-electrode interactions play an essential role, it is often overlooked. This paper reveals the prominent role of graphene interfaces with Fe-storing proteins in the net CT across their tunnel junctions. Here, ferritin (AfFtn-AA) is adsorbed on the graphene by noncovalent amine-graphene interactions confirmed with Raman spectroscopy. In contrast to junctions with metal electrodes, graphene has a vanishing density of states toward its intrinsic Fermi level ("Dirac point"), which increases away from the Fermi level. Therefore, the amount of charge carriers is highly sensitive to temperature and electrostatic charging (induced doping), as deduced from a detailed analysis of CT as a function of temperature and iron loading. Remarkably, the temperature dependence can be fully explained within the coherent tunneling regime due to excitation of hot carriers. Graphene is not only demonstrated as an alternative platform to study CT across biomolecular tunnel junctions, but it also opens rich possibilities in employing interface electrostatics in tuning CT behavior.

Defect Passivation Using a Phosphonic Acid Surface Modifier for Efficient RP Perovskite Blue-Light-Emitting Diodes.

Defect management strategies are vital for enhancing the performance of perovskite-based optoelectronic devices, such as perovskite-based light-emitting diodes (PeLEDs). As additives can fucntion both as acrystallization modifier and/or defect passivator, a thorough study on the roles of additives is essential, especially for blue emissive Pe-LEDs, where the emission is strictly controlled by the n-domain distribution of the Ruddlesden-Popper (RP, L2An-1PbnX3n+1, where L refers to a bulky cation, while A and X are monovalent cation, and halide anion, respectively) perovskite films. Of the various additives that are available, octyl phosphonic acid (OPA) is of immense interest because of its ability to bind with uncoordinated Pb2+ ( notorious for nonradiative recombination) and therefore passivates them. Here, with the help of various spectroscopic techniques, such as X-ray photon-spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), and photoluminescence quantum yield (PLQY) measurements, we demonstrate the capability of OPA to bind and passivate unpaired Pb2+ defect sites. Modification to crystallization promoting higher n-domain formation is also observed from steady-state and transient absorption (TA) measurements. With OPA treatment, both the PLQY and EQE of the corresponding PeLED showed improvements up to 53% and 3.7% at peak emission wavelength of 485 nm, respectively.

Solid-Ionic Memory in a van der Waals Heterostructure.

Defect states dominate the performance of low-dimensional nanoelectronics, which deteriorate the serviceability of devices in most cases. But in recent years, some intriguing functionalities are discovered by defect engineering. In this work, we demonstrate a bifunctional memory device of a MoS2/BiFeO3/SrTiO3 van der Waals heterostructure, which can be programmed and erased by solely one kind of external stimuli (light or electrical-gate pulse) via engineering of oxygen-vacancy-based solid-ionic gating. The device shows multibit electrical memory capability (>22 bits) with a large linearly tunable dynamic range of 7.1 × 106 (137 dB). Furthermore, the device can be programmed by green- and red-light illuminations and then erased by UV light pulses. Besides, the photoresponse under red-light illumination reaches a high photoresponsivity (6.7 × 104 A/W) and photodetectivity (2.12 × 1013 Jones). These results highlighted solid-ionic memory for building up multifunctional electronic and optoelectronic devices.