Highly reusable Bi2O3/electron-Cu-shuttle in-situ immobilized polyacrylonitrile fibrous mat for efficient photocatalytic degradation of methylene blue and rhodamine B dyes.

Organic semiconductor-based photocatalysts have been alluring due to their edge over inorganic photocatalysts. In this study, a reusable copper-bismuth oxide/polyacrylonitrile (Cu-Bi2O3/PAN) fibrous mat was prepared by fast-process flame spray pyrolysis and electrospinning for photocatalytic degradation of methylene blue (MB) and rhodamine B (RhB) dyes. The results confirmed a well-defined morphology of Cu-Bi2O3/PAN fibers and good coordination of flame-made Cu-Bi2O3 particles with the functional groups of PAN. The Cu-Bi2O3/PAN fibrous mat exhibits remarkable photocatalytic performance of 96.2% MB and 98.6% RhB degradation, with a reaction rate as high as about 4.5- and 10.2-times than that of flame-made Cu-Bi2O3 particles and PAN under neutral condition, even after 10 cycles. The Cu-Bi2O3/PAN exhibits complete degradation of MB and RhB in 90 and 150 min under alkaline and slightly acidic conditions, respectively. The synergistic effect of Cu-Bi2O3 and coordination bond between particles and functional groups of PAN promoted carrier migration, suppressed recombination of carriers and provided abundant radicals on the surface of the mat. Superoxide and hydroxyl radicals were the major active species involved in the degradation of RhB and MB, respectively. This work provides an insight into designing the Cu-metal-shuttle based photocatalysts to optimize fibrous mat application in water remediation.

Close-Contact Oxygen Vacancies Synthesized by FSP Promote the Supplement of Active Oxygen Species To Improve the Catalytic Combustion Performance of Toluene.

Catalytic combustion is an important means to reduce toluene pollution, and improving the performance of catalytic combustion catalysts is of great significance for practical applications. The study of oxygen vacancies is one of the key steps to improve catalyst performance. Here, two different oxygen vacancy structures were well-defined and controllably synthesized by flame spray pyrolysis (FSP) to evaluate their effect on the catalytic combustion performance of toluene. The closely contacted oxygen vacancies (c-Vo) enhance the oxygen activation capacity of the catalyst, and the temperature of the first oxygen desorption peak and hydrogen reduction peak is 56 and 37 °C lower than the separated oxygen vacancy (s-Vo) sample, respectively. The oxygen activation energy barrier on the c-Vo is calculated to be negligible of only 0.04 eV. Both in situ DRIFT and DFT calculations indicate that the c-Vo structure accelerates the catalytic oxidation of p-toluene molecules. Moreover, due to the unique characteristics of high-temperature synthesis and rapid quenching, FSP brings excellent water resistance and high-temperature stability to the catalyst. In conclusion, utilizing the FSP in situ reduction strategy can create more c-Vo to improve the catalytic combustion performance of toluene.

Photocatalytic degradation of dyes by novel electrospun nanofibers: A review.

Textile industry is a significant contributor of wastewater, which contains pollutants including dye and other chemical substances. The release of thousands of tons of dye used in textile processing and finishing into natural streams and aquatic bodies present dire harm to the environment. In response to environmental concerns, a number of research have been done using low-cost technology to produce absorbents that can remove dyes from water bodies. Distinct techniques such as adsorption, enzymatic and photocatalytic degradation, etc. have been employed to remove dyes. In the last few decades, photocatalysis, a simple and green strategy, has emerged as the most valuable and recent principle that deals with wastewater treatment, using uniquely fabricated nanomaterials. Among them, rapid and versatile electrospinning methods have been used for the construction of a large surface area, hierarchical and reusable nanofibers for environmental remediation. As a flexible and fast fabrication method, reviewing the use of electrospun photocatalytic nanofibers, influential parameters in electrospinning and their effectiveness in the generation of oxidizing agents are a promising platform for the fabrication of novel nanomaterials in photocatalytic degradation of dyes. This review discusses techniques for dye removal, electrospun nanofibers, their fabrication and application in photocatalysis; mechanism of photocatalytic degradation, and challenges and suggested remedies for electrospun nanofibers in photocatalysis.

Highly efficient Au/Fe2O3 for CO oxidation: The vital role of spongy Fe2O3 toward high catalytic activity and stability.

Supported gold catalysts have drawn great attention for many decades due to their outstanding performance in remedying the environment from carbon monoxide (CO) pollution. In this study, due to the large surface area of spongy Fe2O3, fabricated by salt-assisted ultrasonic spray pyrolysis, a considerable amount of Au was loaded on spongy Fe2O3 compared to low-surface-area non-spongy Fe2O3. It is seen that the spongy Fe2O3 catalyst loaded with Au has an interface that can be extremely active for CO desorption and O2 activation. That means it has high catalytic activity in CO oxidation than non-spongy and low surface area Fe2O3 loaded with Au. Also, the incorporation of Au in low alkaline condition further enhances the interaction between Au and Fe2O3, providing more active sites. This made the catalyst to have better activity, good stability over 60 hrs, and there was no carbonate on its surface. It had full conversion at 30 °C on 120 L g-1h-1 with high TOF (2.2 s-1).