A LaCl3-based lithium superionic conductor compatible with lithium metal.

Inorganic superionic conductors possess high ionic conductivity and excellent thermal stability but their poor interfacial compatibility with lithium metal electrodes precludes application in all-solid-state lithium metal batteries1,2. Here we report a LaCl3-based lithium superionic conductor possessing excellent interfacial compatibility with lithium metal electrodes. In contrast to a Li3MCl6 (M = Y, In, Sc and Ho) electrolyte lattice3-6, the UCl3-type LaCl3 lattice has large, one-dimensional channels for rapid Li+ conduction, interconnected by La vacancies via Ta doping and resulting in a three-dimensional Li+ migration network. The optimized Li0.388Ta0.238La0.475Cl3 electrolyte exhibits Li+ conductivity of 3.02 mS cm-1 at 30 °C and a low activation energy of 0.197 eV. It also generates a gradient interfacial passivation layer to stabilize the Li metal electrode for long-term cycling of a Li-Li symmetric cell (1 mAh cm-2) for more than 5,000 h. When directly coupled with an uncoated LiNi0.5Co0.2Mn0.3O2 cathode and bare Li metal anode, the Li0.388Ta0.238La0.475Cl3 electrolyte enables a solid battery to run for more than 100 cycles with a cutoff voltage of 4.35 V and areal capacity of more than 1 mAh cm-2. We also demonstrate rapid Li+ conduction in lanthanide metal chlorides (LnCl3; Ln = La, Ce, Nd, Sm and Gd), suggesting that the LnCl3 solid electrolyte system could provide further developments in conductivity and utility.

Dimensional and Doping Engineering of Chiral Perovskites with Enhanced Spin Selectivity for Green Emissive Spin Light-Emitting Diodes.

Chiral perovskites play a pivotal role in spintronics and optoelectronic systems attributed to their chiral-induced spin selectivity (CISS) effect. Specifically, they allow for spin-polarized charge transport in spin light-emitting diodes (LEDs), yielding circularly polarized electroluminescence at room temperature without external magnetic fields. However, chiral lead bromide-based perovskites have yet to achieve high-performance green emissive spin-LEDs, owing to limited CISS effects and charge transport. Herein, we employ dimensional regulation and Sn2+-doping to optimize chiral bromide-based perovskite architecture for green emissive spin-LEDs. The optimized (PEA)x(S/R-PRDA)2-xSn0.1Pb0.9Br4 chiral perovskite film exhibits an enhanced CISS effect, higher hole mobility, and better energy level alignment with the emissive layer. These improvements allow us to fabricate green emissive spin-LEDs with an external quantum efficiency (EQE) of 5.7% and an asymmetry factor |gCP-EL| of 1.1 × 10-3. This work highlights the importance of tailored perovskite architectures and doping strategies in advancing spintronics for optoelectronic applications.

Fabrication of the flower-like Z-scheme heterojunction photocatalyst Bi-BiOI/UiO 66 for enhanced photodegradation of acetaminophen in simulated wastewater.

Acetaminophen is a representative contaminant of emerging persistent organic pollutants that can cause environmental problems when it enters municipal wastewater. An innovative flower-like Z-scheme photocatalyst Bi-BiOI/UiO 66 heterojunction composite was designed and constructed via a one-step solvothermal method. Investigations demonstrated that the Z-scheme structure strongly contributes to increasing the degradation efficiency of micropollutants. The results indicate that the bandgap energy (Eg) of the Bi-BiOI/UiO 66 composite decreases significantly from 3.22 eV to 2.43 eV, in comparison with that of pure copper-based UiO 66. Under suitable conditions (5 mg/L Ace, pH 3, 0.05 g/L), the organic pollutants in the water can be removed completely. A k value of 5.67 × 10-2 min-1 for the Bi-BiOI/UiO 66 heterojunction composite was found to effectively represent the acetaminophen photodegradation process. The reaction mechanism of acetamide in aqueous solution is also discussed. The Bi in Bi-BiOI can use surface plasmon resonance to form an electric field and accelerate the separation of photogenerated electrons and holes. This study highlights the potential of a novel photocatalyst for practical application.

Impacts of dibutyl phthalate on bacterial community composition and carbon and nitrogen metabolic pathways in a municipal wastewater treatment system.

Dibutyl phthalate (DBP) is a typical toxic and hazardous pollutant in pharmaceutical wastewater, affecting the metabolism of microbial flora, leading to decreased treatment efficiency, and deteriorated effluent quality in municipal wastewater treatment plants (WWTPs). This study conducted a long-term experiment with 6 operational stages in a pilot-scale A2O-MBR system, analyzing the effect of DBP on the bacterial community and their carbon and nitrogen metabolic pathways. 16S rRNA gene amplicon sequencing analysis and principal components analysis (PCA) showed that DBP at 8 mg/L significantly influenced the structure of bacterial community (P < 0.05), resulting in reduced bacterial community diversity. Metagenomic analysis was used to explore the embedded carbon and nitrogen metabolic pathways. At the presence of DBP, the metabolism of saccharides, lipids, and aromatic compounds were blocked owing to the vanishment of key enzyme (such as acetylaminohexosyltransferase (EC 2.4.1.92) and UDP-sugar pyro phosphorylase (EC 2.7.7.64)) encoding genes, resulting in weakened carbon metabolism, and thus reduced COD removal performance. The resultant deficiency of the genes such as those encoding hydroxyproline dehydrogenase (EC 1.5.5.3) gave rise to interrupted metabolic pathways of amino acid (arginine, proline, tyrosine, and tryptophan), resulting in declined function of nitrogen metabolism and thus reduced TN removal efficiency. The uncovery of the mechanisms by which DBP affects wastewater treatment system efficiency and microbial metabolism is of theoretical importance for the efficient operation of municipal and pharmaceutical wastewater treatment systems.

Insight into the microbial nitrogen cycle in riparian soils in an agricultural region.

Riparian zones are considered as an effective measure on preventing agricultural non-point source nitrogen (N) pollution. However, the mechanism underlying microbial N removal and the characteristics of N-cycle in riparian soils remain elusive. In this study, we systematically monitored the soil potential nitrification rate (PNR), denitrification potential (DP), as well as net N2O production rate, and further used metagenomic sequencing to elucidate the mechanism underlying microbial N removal. As a whole, the riparian soil had a very strong denitrification, with the DP 3.17 times higher than the PNR and 13.82 times higher than the net N2O production rate. This was closely related to the high soil NO3--N content. In different profiles, due to the influence of extensive agricultural activities, the soil DP, PNR, and net N2O production rate near the farmland edge were relatively low. In terms of N-cycling microbial community composition, the taxa of denitrification, dissimilatory nitrate reduction, and assimilatory nitrate reduction accounted for a large proportion, all related to NO3--N reduction. The N-cycling microbial community in waterside zone showed obvious differences to the landside zone. The abundances of N-fixation and anammox genes were significantly higher in the waterside zone, while the abundances of nitrification (amoA&B&C) and urease genes were significantly higher in the landside zone. Furthermore, the groundwater table was an important biogeochemical hotspot in the waterside zone, the abundance of N-cycle genes near the groundwater table was at a relative higher level. In addition, compared to different soil depths, greater variation in N-cycling microbial community composition was observed between different profiles. These results reveal some characteristics of the soil microbial N-cycle in the riparian zone in an agricultural region and are helpful for restoration and management of the riparian zone.

Activated carbon enhanced traditional activated sludge process for chemical explosion accident wastewater treatment.

With the development of industries, explosion accidents occur frequently during production, transportation, usage and storage of hazard chemicals. It remained challenging to efficiently treat the resultant wastewater. As an enhancement of traditional process, the activated carbon-activated sludge (AC-AS) process has a promising potential in treating wastewater with high concentrations of toxic compounds, chemical oxygen demand (COD) and ammonia nitrogen (NH4+-N), etc. In this paper, activated carbon (AC), activated sludge (AS) and AC-AS were used to treat the wastewater produced from an explosion accident in the Xiangshui Chemical Industrial Park. The removal efficiency was assessed by the removal performances of COD, dissolved organic carbon (DOC), NH4+-N, aniline and nitrobenzene. Increased removal efficiency and shortened treatment time were achieved in the AC-AS system. To achieve the same COD, DOC and aniline removal (90%), the AC-AS system saved 30, 38 and 58 h compared with the AS system, respectively. The enhancement mechanism of AC on the AS was explored by metagenomic analysis and three-dimensional excitation-emission-matrix spectra (3DEEMs). More organics, especially aromatic substances were removed in the AC-AS system. These results showed that the addition of AC promoted the microbial activity in pollutant degradation. Bacteria, such as Pyrinomonas, Acidobacteria and Nitrospira and genes, such as hao, pmoA-amoA, pmoB-amoB and pmoC-amoC, were found in the AC-AS reactor, which might have played important roles in the degradation of pollutants. To sum up, AC might have enhanced the growth of aerobic bacteria which further improved the removal efficiency via the combined effects of adsorption and biodegradation. The successful treatment of Xiangshui accident wastewater using the AC-AS demonstrated the potential universal characteristics of the process for the treatment of wastewater with high concentration of organic matter and toxicity. This study is expected to provide reference and guidance for the treatment of similar accident wastewaters.

Optimization and trade-off framework for coupled green-grey infrastructure considering environmental performance.

Implementing runoff control infrastructure has been regarded as an efficacious measure in stormwater management. The issue of its cost-effectiveness is a primary concern for decision makers since it is an exorbitant investment. However, most of existed studies only concentrated on the cost-effectiveness optimization of runoff control infrastructure, especially green infrastructure, between hydrological and economic aspects, and therefore, the potential layout scenarios with high extra environmental benefits could be neglected in the traditional two-dimensional frameworks. In this study, a novel carbon dioxide equivalent-based index was quantified to represent the extra environmental benefits of runoff control infrastructure besides stormwater management and was further integrated into the assessment framework. The effectiveness of green and grey infrastructure was comprehensively evaluated and traded off between hydrological, environmental and economic aspects. The results demonstrated that grey infrastructure is a better measure than green infrastructure when only hydrological (HF index) and economic (CI index) performances were considered. Nevertheless, the environmental performance (EROI index) of green infrastructure prevails over grey infrastructure, and when optimizing green and grey infrastructure simultaneously in the three-dimensional framework considering environmental effectiveness, green infrastructure is comparable with grey infrastructure. Furthermore, an appropriate composition of coupled green-grey infrastructure is requisite, which could achieve an optimal trade-off between hydrological and environmental effectiveness. The sources of environmental benefits were also identified and analyzed from three representative preference scenarios. The findings of the study could serve as a trade-off basis between green and grey infrastructure, as well as between EROI and HF.

Fabrication, characterization, and application of BiOI@ZIF-8 nanocomposite for enhanced photocatalytic degradation of acetaminophen from aqueous solutions under UV-vis irradiation.

This work investigates the use of novel BiOI@ZIF-8 nanocomposite for the removal of acetaminophen (Ace) from synthetic wastewater. The samples were analyzed using FTIR, XRD, XPS, DRS, PL, FESEM-EDS, and ESR techniques. The effects of the loading capacity of ZIF-8 on the photocatalytic oxidation performance of bismuth oxyiodide (BiOI) were studied. The photocatalytic degradation of Ace was maximized by optimizing pH, reaction time and the amount of photocatalyst. On this basis, the removal mechanisms of the target pollutant by the nanocomposite and its photodegradation pathways were elucidated. Under optimized conditions of 1 g/L of composite, pH 6.8, and 4 h of reaction time, it was found that the BiOI@ZIF-8 (w/w = 1:0.01) nanocomposite exhibited the highest Ace removal (94%), as compared to that of other loading ratios at the same Ace concentration of 25 mg/L. Although this result was encouraging, the treated wastewater still did not satisfy the required statutory of 0.2 mg/L. It is suggested that the further biological processes need to be adopted to complement Ace removal in the samples. To sustain its economic viability for wastewater treatment, the spent composite still could be reused for consecutive five cycles with 82% of regeneration efficiency. Overall, this series of work shows that the nanocomposite was a promising photocatalyst for Ace removal from wastewater samples.

α-BaF2 Nanoparticle Substrate-Enabled γ-CsPbI3 Heteroepitaxial Growth for Efficient and Bright Deep-Red Light-Emitting Diodes.

All-inorganic CsPbI3 perovskite is attractive for deep-red light-emitting diodes (LEDs) because of its excellent carrier mobility, high color purity, and solution processability. However, the high phase transition energy barrier of optically active CsPbI3 black phase hinders the fabrication of efficient and bright LEDs. Here, we report a novel α-BaF2 nanoparticle substrate-promoted solution-processable heteroepitaxial growth to overcome this hindrance and obtain high-quality optically active γ-CsPbI3 thin films, achieving efficient and bright deep-red LEDs. We unravel that the highly exposed planes on the α-BaF2 nanoparticle-based heteroepitaxial growth substrate have a 99.5% lattice matching degree with the (110) planes of γ-CsPbI3. This ultrahigh lattice matching degree initiates solution-processed interfacial strain-free epitaxial growth of low-defect and highly oriented γ-CsPbI3 thin films on the substrate. The obtained γ-CsPbI3 thin films are uniform, smooth, and highly luminescent, based on which we fabricate efficient and bright deep-red LEDs with a high peak external quantum efficiency of 14.1% and a record luminance of 1325 cd m-2.

Spectrally Stable and Efficient Pure Red CsPbI3 Quantum Dot Light-Emitting Diodes Enabled by Sequential Ligand Post-Treatment Strategy.

Metal halide perovskites are promising semiconductors for next-generation light-emitting diodes (LEDs) due to their high luminance, excellent color purity, and handily tunable band gap. However, it remains a great challenge to develop perovskite LEDs (PeLEDs) with pure red emission at the wavelength of 630 nm. Herein, we report a spectrally stable and efficient pure red PeLED by employing sequential ligand post-treated CsPbI3 quantum dots (QDs). The synthesized CsPbI3 QDs with a size of ∼5 nm are treated in sequential steps using the ligands of 1-hydroxy-3-phenylpropan-2-aminium iodide (HPAI) and tributylsulfonium iodide (TBSI), respectively. The CsPbI3 QD films exhibit improved optoelectronic properties, which enables the fabrication of a pure red PeLED with a peak external quantum efficiency (EQE) of 6.4% and a stable EL emission centered at the wavelength of 630 nm. Our reported sequential ligand post-treatment strategy opens a new route to improve the stability and efficiency of PeLEDs based on QDs.

Thermochromic Phosphors Based on One-Dimensional Ionic Copper-Iodine Chains Showing Solid-State Photoluminescence Efficiency Exceeding 99 .

Thermochromic phosphors are intriguing materials for realizing thermochromic behaviors of light-emitting diodes. Here a highly luminescent and stable thermochromic phosphor based on one-dimensional Cu4 I6 (4-dimethylamino-1-ethylpyridinium)2 is reported. This unique ionic copper-iodine chain-based hybrid exhibits near-unity photoluminescence efficiency owing to the through-space charge-transfer character of relevant electronic transitions. More importantly, an alternative mechanism of thermochromic phosphorescence was unraveled, supported by a first principles simulation of concerted copper atom migration in the copper-iodine chain. Furthermore, we successfully fabricate a bright thermochromic light-emitting diode using this Cu4 I6 (4-dimethylamino-1-ethylpyridinium)2 thermochromic phosphor. Our reported flexible ionic copper-iodine chain-based thermochromic luminescent material represents a new type of cost-effective functional phosphor.

Overexpression of let-7d explains down-regulated KDM3A and ENO2 in the pathogenesis of preeclampsia.

Pre-eclampsia (PE) is the leading cause of maternal death; however, the causative molecular basis remains largely unknown. Recent studies have revealed the important role microRNAs (miRNAs) play in PE. We aimed to explore the effects of let-7d on trophoblast proliferation, migration, invasion and apoptosis in PE and its underlying mechanism. Placental tissues were collected from PE patients and healthy pregnant women, and it was found that let-7d expression was increased, while KDM3A and ENO2 expression was decreased in PE tissues and cells. Bioinformatics analysis indicated the interaction among let-7d, KDM3A and ENO2, confirmed by dual luciferase reporter gene assay; ChIP experiment identified methylated modification to ENO2 by KDM3A. With gain- and loss-function method, silencing of let-7d increased KDM3A expression and enhanced the binding between KDM3A and ENO2. Furthermore, overexpression of let-7d suppressed cell proliferation, migration and invasion of trophoblasts, and induced apoptosis of trophoblasts, while these capacities were restored upon additional treatment of overexpressed ENO2. PE rat models were established to explore the effects of let-7d and ENO2 on PE in vivo. The results established that the silencing of let-7d alleviated the tissue injury and PE-related symptoms when reducing urine protein, TUNEL-positive cells and increasing ENO2, and KDM3A expression in rats. Cumulatively, let-7d suppressed cell progression of trophoblasts, and induced apoptosis through the down-regulation of KDM3A to promote ENO2 methylation, thereby promoting progression of PE. Such an epigenetic network of let-7d, KDM3A and ENO2 in the pathogenesis of PE might provide novel insight into targeted therapy against this disorder.

Elevated MST1 leads to apoptosis via depletion of YAP1 in cardiomyocytes exposed to high glucose.

BACKGROUND: Gestational diabetes mellitus is a risk factor for congenital heart defects. The article aimed to investigate the expression and roles of MST1, YAP1, Last1/2 and Survivin in modulating HG-induced cardiomyocyte apoptosis and maternal diabetes-induced heart abnormality. METHODS: Diabetes mellitus was induced in rats using streptozotocin. The protein expression and phosphorylation analysis in fetal heart tissue was assessed by western blot and immunohistochemical staining. Hoechst 33342 staining assay was performed to explore H9C2 apoptosis. The gene and protein expression in H9C2 cells was assessed by quantitative PCR and western blot. Knockdown of gene expression was assessed by RNA interference. RESULTS: Our results revealed that increased MST1 protein levels in the heart tissues of the offspring of diabetic rats in vivo and in H9C2 cardiomyocytes under HG treatment in vitro, respectively. Knockdown and overexpression experiments showed that MST1 played a key role in mediating HG-induced apoptosis in cardiomyocytes. Downregulation of YAP1 was associated with HG-induced, MST1-mediated cardiomyocyte apoptosis. Further study showed that MST1 downregulated the protein level of YAP1 through mediation of YAP1 phosphorylation on Ser127 and Ser397; this process also required LATS1/2 participation. MST1 overexpression increased the phosphorylation levels of LATS1/2, which were also shown to be increased in the heart tissues of diabetic offspring. We also found that YAP1 mediated the expression of Survivin during HG-induced apoptosis, and the Survivin-inhibitor YM155 partially inhibited the role of YAP1 in suppressing apoptosis induced by HG in cardiomyocytes. CONCLUSION: These findings reveal a regulatory mechanism of MST1/YAP1/Survivin signaling in modulating cardiomyocyte apoptosis in vitro and maternal diabetes-induced congenital heart defects in vivo.

Blow-Spinning Enabled Precise Doping and Coating for Improving High-Voltage Lithium Cobalt Oxide Cathode Performance.

Lithium cobalt oxide (LiCoO2) possesses an attractive theoretical specific capacity (274 mAh g-1) and high discharge voltage (∼4.2 V vs Li+/Li). However, only a half of the theoretical capacity of LiCoO2 is available in commercialized lithium ion batteries because of the intrinsic structural instability and detrimental interface of LiCoO2 at the charging voltage over 4.2 V. Here, a facile blow-spinning synthetic method is developed to realize precise doping and simultaneous self-assembly coating of LiCoO2 particles, achieving a record performance among present LiCoO2 cathodes. Owing to the spatial confinement effect of microfibers fabricated by blow-spinning, homogeneously Mn and La doped in the LiCoO2 host and uniformly Li-Ti-O segregated at the LiCoO2 surface can be realized in every batch of samples. It is demonstrated that the Mn and La codoping can suspend the intrinsic instability and increase the Li+ diffusivity of the LiCoO2 host, and the Ti-based coating can stabilize the interface of LiCoO2 particles at the charging voltage up to 4.5 V. As a result, the obtained comodified LiCoO2 cathode shows the best rate performance (1.85 mAh cm-2 at 2C) and longest cycling stability under an areal capacity of 2.04 mAh cm-2 (83% capacity retention over 300 cycles at 0.3C), in comparison to previously reported LiCoO2 cathodes.

Degradation of dissolved organic matter in effluent of municipal wastewater plant by a combined tidal and subsurface flow constructed wetland.

Dissolved organic matter (DOM) is an important constituent of wastewater treatment plant (WWTP) effluent. A novel combined tidal and subsurface flow constructed wetland (TF-SSF-CW) of 90 L was constructed for a ten-month trial of advanced treatment of the WWTP effluent. Excitation emission matrix (EEM) fluorescence spectroscopy, parallel factor (PARAFAC) analysis and a two end-member mixing model were employed to characterize the composition and removal process of the effluent DOM (EfOM) from the WWTP. The results showed that the TF-SSF-CW performed an efficient EfOM removal with dissolved organic carbon (DOC) removal rate of 88% and dissolved organic nitrogen (DON) removal rate of 91%. Further analysis demonstrated that the EfOM consisted mainly of two protein moieties and two humic-like groups; protein moieties (76%) constituted the main content of EfOM in raw water and humic-like groups (57%) became the dominating contributor after treatment. The EfOM from the WWTP was mainly of aquatic bacterial origin and evolved to a higher proportion of terrigenous origin with higher humification in the TF-SSF-CW effluent. A common controlling treatment-related factor for determining the concentrations of the same kind of substances (protein groups or humic-like groups) was revealed to exist, and the ratio of removal rates between the same substances in treatment was calculated. Our study demonstrates that the TF-SSF-CW can be a novel and effective treatment method for the EfOM from WWTPs, and is helpful for understanding of the character of EfOM in wetland treatment.

Lead removal from water using organic acrylic amine fiber (AAF) and inorganic-organic P-AAF, fixed bed filtration and surface-induced precipitation.

Granular porous sorbents were normally used for heavy metals removal from water. To search for the new commercial sorbent and treatment strategy, an organic acrylic amine fiber (AAF) and phosphorus loading inorganic-organic AAF (P-AAF) were prepared and used for lead (Pb) removal from water. A new strategy of inorganic-organic coupling technology was proposed for Pb removal, based on the hypothesis of surface-induced precipitation mechanism. The AAF showed a Pb adsorption capacity of 417 mg/g from the Langmuir fitting, while the column filtration technology was further applied to measure the adsorption edge and applications. Effects of different initial Pb concentrations, hydraulic retention time, and co-existing P were considered in the filtration experiments. The presence of 0.8 mg/L P in water significantly improved the Pb breakthrough point from 15,000 to 41,000 bed volumes of water spiked with 85 µg/L Pb, while the P-AAF fixed bed showed better removal of Pb than AAF SEM/EDX and XRD spectra were employed for determining the surface functional groups and the formation of surface-induced precipitation of pyromorphite (Pb5(PO4)3OH) on AAF. This study verified the application of AAF sorbent for Pb removal and the enhanced effect of coating P on AAF, thus improved our fundamental understanding and application of the surface chemistry process of Pb with P.

Insights into the key components of bacterial assemblages in typical process units of oily wastewater treatment plants.

To compare the structure of microbial community in the oily wastewater treatment plants (OWWTPs) located in China, and to discern the impacts of environment variables on the variance of microbial community, activated sludge samples from six typical OWWTPs were taken and the structure of microbial community of these six samples were analyzed via Illumina high-throughput sequencing. 18 core genera including Comamonas, Bacillus, Pseudomonas, Thauera, Paenibacillus, etc. were shared by all OWWTPs. Canonical correspondence analysis (CCA) suggested that temperature, oil concentration, DO and pH exhibited significant impacts in shaping the structure of microbial community. Variance partitioning analyses (VPA) illuminated that the most variation in microbial community was contributed to geographic location, explaining 36.4% of the total variations obtained, followed by wastewater characteristics (18.7%) and operational parameters (8.6%). This work offered insights into the structure of microbial community in OWWTPs at different geographic locations and illustrated the correlations between environment variables and microbial community in OWWTPs.

Adsorption and recovery of phosphate from water by amine fiber, effects of co-existing ions and column filtration.

A weak-base adsorption fiber, acrylic amine fiber (AAF), was prepared for removal and recovery of phosphate from water. The adsorption properties of the AAF for phosphate and effects of co-existing ions were investigated using batch and column filtration experiments, scanning electron microscope, and Fourier transform infrared techniques. Experimental results showed that AAF had a high phosphate adsorption capacity of 119 mg/g at pH 7.0. The effects of calcium, sulfate, carbonate, nitrate, and fluoride showed that sulfate and calcium inhibited phosphate adsorption. However, AAF showed higher binding affinity toward phosphate than sulfate. Column filtration results showed that AAF could filter 1420 bed volumes of tap water containing 1.0 mg-P/L of phosphate. The saturated AAF could be regenerated using 0.5 mol/L hydrochloric acid solution and reused. After desorption, phosphate was recovered through precipitation of hydroxyapatite (Ca5(PO4)3OH). The easy of regeneration, good adsorption performance, and the fiber morphology of AAF make it an attractive alternative for phosphate recovery from multiple water sources.

Enhanced Capture Ability of Sludge-Derived Mesoporous Biochar with a Template-like Method.

Sewage sludge-derived mesoporous biochars (SS-MBCs) were prepared by using cationic polyacrylamide (PAM+) as a template agent through a template-like method under high temperature and employed for getting rid of methylene blue (MB) from water. Textural evolution, mesostructured morphology, thermodynamic properties, and surface chemical groups of SS-MBCs were analyzed. It showed that PAM+ not only played an important role in good nucleation that brought well-developed texture and novel pore size distribution to SS-MBCs but also improved the MB adsorption capacities of SS-MBCs by increasing the specific surface area and the content of oxygen functional groups, especially the lactone. Preparation factor analysis indicated that PAM+ concentration, dosage of additive sludge, and carbonization temperature had distinct effects on material structure and adsorption performance especially above the pyrolytic temperature of 800 °C. The adsorption kinetics and isotherms were analyzed in detail, and it revealed that the kinetics and equilibrium adsorptions of SS-MBCs could be well-described by the Langmuir isotherm model and pseudo-second-order kinetics, respectively. Remarkably, the SS-MBCs showed higher removal efficiency and adsorption capacity than commercial activated carbon and most reported sludge-based adsorbents.

Effect of phosphate releasing in activated sludge on phosphorus removal from municipal wastewater.

Aluminum and ferric salts are commonly used in municipal wastewater treatment plants (WWPTs) for phosphorus (P) removal. In this study, on-site jar tests were conducted to determine the removal of different P species from the fresh samples in the presence and absence of activated sludge (AS) with different doses of alum, poly-aluminum chloride, and ferric chloride at different pH. The soluble P (SP) concentration in the samples was about 0.63mg/L. When the mixed liquor containing AS was treated with 8mg/L of Al, SP could be reduced to 0.13mg/L, while it was reduced to 0.16mg/L with only 1mg/L of Al after sedimentation removal of AS from sample. Chemical analysis determined that AS contained 59.8mg-P/g-TSS and 43.8mg-Al/g-TSS and most of the P was associated with the aluminum hydroxide. We discovered that the phosphate in the AS could readily be released from it, which was mainly responsible for ineffective removal of P to low levels in mixed liquor even with very high alum dose. This study provides new insight into the behavior and fate of P in the wastewater treatment plants that use alum to enhance P removal in the final effluent.