Ultrafast THz spectroscopy of carbon nanotube-graphene composites.

Mixed nanomaterial composites can combine the excellent properties of well-known low-dimensional nanomaterials. Here we highlight the potential of one-dimensional single-walled carbon nanotubes interfaced with two-dimensional graphene by exploring the composite's ac conductivity and photoconductivity, and the influence of HAuCl4doping. In the composite, the equilibrium terahertz conductivity from free carrier motion was boosted, while the localised plasmon peak shifted towards higher frequencies, which we attribute to shorter conductivity pathways in the composite. A negative terahertz photoconductivity was observed for all samples under 410 nm optical excitation and was reproduced by a simple model, where the Drude spectral weight and the momentum scattering rate were both lowered under photoexcitation. The composite had an enhanced modulation depth in comparison to reference carbon nanotube films, while retaining their characteristically fast (picosecond) response time. The results show that carbon nanotube-graphene composites offer new opportunities in devices by controlling charge carrier transport and tuning their optoelectronic properties.

Transparent and flexible high-performance supercapacitors based on single-walled carbon nanotube films.

Transparent and flexible energy storage devices have garnered great interest due to their suitability for display, sensor and photovoltaic applications. In this paper, we report the application of aerosol synthesized and dry deposited single-walled carbon nanotube (SWCNT) thin films as electrodes for an electrochemical double-layer capacitor (EDLC). SWCNT films exhibit extremely large specific capacitance (178 F g(-1) or 552 µF cm(-2)), high optical transparency (92%) and stability for 10 000 charge/discharge cycles. A transparent and flexible EDLC prototype is constructed with a polyethylene casing and a gel electrolyte.

Carbon nanotube-amorphous silicon hybrid solar cell with improved conversion efficiency.

We report a hybrid solar cell based on single walled carbon nanotubes (SWNTs) interfaced with amorphous silicon (a-Si). The high quality carbon nanotube network was dry transferred onto intrinsic a-Si forming Schottky junction for metallic SWNT bundles and heterojunctions for semiconducting SWNT bundles. The nanotube chemical doping and a-Si surface treatment minimized the hysteresis effect in current-voltage characteristics allowing an increase in the conversion efficiency to 1.5% under an air mass 1.5 solar spectrum simulator. We demonstrated that the thin SWNT film is able to replace a simultaneously p-doped a-Si layer and transparent conductive electrode in conventional amorphous silicon thin film photovoltaics.

High-permittivity Solvents Increase MXene Stability and Stacking Order Enabling Ultraefficient Terahertz Shielding.

2D transition metal carbides and nitrides (MXenes) suggest an uncommonly broad combination of important functionalities amongst 2D materials. Nevertheless, MXene suffers from facile oxidation and colloidal instability upon conventional water-based processing, thus limiting applicability. By experiments and theory, It is suggested that for stability and dispersibility, it is critical to select uncommonly high permittivity solvents such as N-methylformamide (NMF) and formamide (FA) (εr  = 171, 109), unlike the classical solvents characterized by high dipole moment and polarity index. They also allow high MXene stacking order within thin films on carbon nanotube (CNT) substrates, showing very high Terahertz (THz) shielding effectiveness (SE) of 40-60 dB at 0.3-1.6 THz in spite of the film thinness < 2 µm. The stacking order and mesoscopic porosity turn relevant for THz-shielding as characterized by small-angle X-ray scattering (SAXS). The mechanistic understanding of stability and structural order allows guidance for generic MXene applications, in particular in telecommunication, and more generally processing of 2D materials.

Machine Learning for Tailoring Optoelectronic Properties of Single-Walled Carbon Nanotube Films.

A machine learning technique, namely, support vector regression, is implemented to enhance single-walled carbon nanotube (SWCNT) thin-film performance for transparent and conducting applications. We collected a comprehensive data set describing the influence of synthesis parameters (temperature and CO2 concentration) on the equivalent sheet resistance (at 90% transmittance in the visible light range) for SWCNT films obtained by a semi-industrial aerosol (floating-catalyst) CVD with CO as a carbon source and ferrocene as a catalyst precursor. The predictive model trained on the data set shows principal applicability of the method for refining synthesis conditions toward the advanced optoelectronic performance of multiparameter processes such as nanotube growth. Further doping of the improved carbon nanotube films with HAuCl4 results in the equivalent sheet resistance of 39 Ω/□-one of the lowest values achieved so far for SWCNT films.

Aerosol-Assisted Fine-Tuning of Optoelectrical Properties of SWCNT Films.

We propose a novel, scalable, and simple method for aerosol doping of single-walled carbon nanotube (SWCNT) films. This method is based on aerosolization of a dopant solution (HAuCl4 in ethanol) and time-controlled deposition of uniform aerosol particles on the nanotube film surface. The approach developed allows fine-tuning of the SWCNT work function in the range of 4.45 (for pristine nanotubes) to 5.46 eV, controllably varying the sheet resistance of the films from 79 to 3.2 Ω/□ for the SWCNT films with 50% transmittance (at 550 nm). This opens a new avenue for traditional and flexible optoelectronics, both to replace existing indium-tin oxide electrodes and to develop novel applications of the highly conductive transparent films.

A One-Step Method of Hydrogel Modification by Single-Walled Carbon Nanotubes for Highly Stretchable and Transparent Electronics.

Electrically conductive hydrogels (ECHs) are attracting much interest in the field of biomaterials science because of their unique properties. However, effective incorporation and dispersion of conductive materials in the matrices of polymeric hydrogels for improved conductivity remains a great challenge. Here, we demonstrate highly transparent, electrically conductive, stretchable tough hydrogels modified by single-walled carbon nanotubes (SWCNTs). Two different approaches for the fabrication of SWCNT/hydrogel structures are examined: a simple SWCNT film transfer onto the as-prepared hydrogel and the film deposition onto the pre-stretched hydrogel. Functionality of our method is confirmed by scanning electron microscopy along with optical and electrical measurements of our structures while subjecting them to different strains. Since the hydrogel-based structures are intrinsically soft, stretchable, wet, and sticky, they conform well to a human skin. We demonstrate applications of our material as skin-like passive electrodes and active finger-mounted joint motion sensors. Our technique shows promise to accelerate the development of biointegrated wearable electronics.

Holey single-walled carbon nanotubes for ultra-fast broadband bolometers.

Although carbon nanotubes have already been demonstrated to be a promising material for bolometric photodetectors, enhancing sensitivity while maintaining the speed of operation remains a great challenge. Here, we present a holey carbon nanotube network, designed to improve the temperature coefficient of resistance for highly sensitive ultra-fast broadband bolometers. Treatment of carbon nanotube films with low-frequency oxygen plasma allows fine tuning of the electronic properties of the material. The temperature coefficient of resistance of our films is much greater than the reported values for pristine carbon nanotubes, up to -2.8% K-1 at liquid nitrogen temperature. The bolometer prototypes made from the treated films demonstrate high sensitivity over a wide IR range, a short response time, smooth spectral characteristics and a low noise level.