Fast-Disintegrating Nanofibrous Web of Pullulan/Griseofulvin-Cyclodextrin Inclusion Complexes.

Griseofulvin (GSF) is one of the most widely used antifungal suffering from low water solubility and limited bioavailability. Here, cyclodextrin (CD) derivatives of hydroxypropyl-beta-CD (HPßCD) known for its high-water solubility were used to form inclusion complexes (ICs) with GSF. Here, the molecular modeling study revealed the more efficient complex formation with 1:2 (guest:CD) stoichiometry, so ICs of GSF-HPßCD were prepared using a 1:2 molar ratio (GSF:HPßCD) and then mixed with pullulan (PULL) to generate nanofibers (NFs) using the electrospinning technique. PULL is a nontoxic water-soluble biopolymer and the ultimate PULL/GSF-HPßCD-IC NF was obtained with a defect-free fiber morphology having 805 ± 180 nm average diameter. The self-standing and flexible PULL/GSF-HPßCD-IC NF was achieved to be produced with a loading efficiency of ∼98% corresponding to ∼6.4% (w/w) of drug content. In comparison, the control sample of PULL/GSF NF was formed with a lower loading efficiency value of ∼72% which equals to ∼4.7% (w/w) of GSF content. Additionally, PULL/GSF-HPßCD-IC NF provided an enhanced aqueous solubility for GSF compared to PULL/GSF NF so a faster release profile with ∼2.5 times higher released amount was obtained due to inclusion complexation between GSF and HPßCD within the nanofibrous web. On the other hand, both nanofibrous webs rapidly disintegrated (∼2 s) in the artificial saliva medium that mimics the oral cavity environment. Briefly, PULL/GSF-HPßCD-IC NF can be a promising dosage formulation as a fast-disintegrating delivery system for antifungal oral administration owing to the improved physicochemical properties of GSF.

Orally Fast Disintegrating Cyclodextrin/Prednisolone Inclusion-Complex Nanofibrous Webs for Potential Steroid Medications.

Prednisolone is a widely used immunosuppressive and anti-inflammatory drug type that suffers from low aqueous solubility and bioavailability. Due to the inclusion complexation with cyclodextrins (CDs), prednisolone's drawbacks that hinder its potential during the administration can be eliminated effectively. Here, we have early shown the electrospinning of free-standing nanofibrous webs of CD/prednisolone inclusion complexes (ICs) in the absence of a polymer matrix. In this study, hydroxypropyl-beta-CD (HPßCD) has been used to form ICs with prednisolone and generate nanofibrous webs with a drug loading capacity of ∼10% (w/w). Pullulan/prednisolone nanofibrous webs have been also fabricated as a control sample having the same drug loading (∼10%, w/w). It has been demonstrated that prednisolone has been found in an amorphous state in the HPßCD/prednisolone nanofibrous web due to inclusion complexation, while it has retained its crystal structure in the pullulan/prednisolone nanofibrous web. Therefore, the HPßCD/prednisolone IC nanofibrous web has shown a faster and enhanced release profile and superior disintegration feature in artificial saliva than the pullulan/prednisolone nanofibrous web. The complexation energy calculated using ab initio modeling displayed a more favorable interaction between HPßCD and prednisolone in the case of a molar ratio of 2:1 than 1:1 (CD: drug). Here, the HPßCD/prednisolone IC nanofibrous web has been developed without using a toxic component or solvent to dissolve drug molecules and boost drug loading in amorphous nature. The investigation of IC nanofibrous webs has been conducted to formulate a promising alternative to the orally disintegrating tablet formulation of prednisolone in the market. The nanofibrous structure and the improved physicochemical properties of prednisolone arising with the complexation might ensure a faster disintegration and onset of action against commercially available and orally disintegrating delivery systems during the desired treatment.

Fast Dissolving Oral Drug Delivery System Based on Electrospun Nanofibrous Webs of Cyclodextrin/Ibuprofen Inclusion Complex Nanofibers.

In this study, the polymer-free electrospinning was performed in order to produce cyclodextrin/ibuprofen inclusion complex nanofibers, which could have potential as the fast dissolving oral drug delivery system. Ibuprofen is a poorly water-soluble nonsteroidal anti-inflammatory drug; however, the water solubility of ibuprofen can be significantly enhanced by inclusion complexation with cyclodextrins. Here, hydroxypropyl-beta-cyclodextrin (HPßCyD) was chosen both as a nanofiber matrix and host molecule for inclusion complexation in order to enhance water solubility and fast dissolution of ibuprofen. Ibuprofen was inclusion-complexed with HPßCyD in highly concentrated aqueous solutions of HPßCyD (200%, w/v) having two different molar ratios: 1:1 and 2:1 (HPßCyD/ibuprofen). The HPßCyD/ibuprofen-IC (1:1) aqueous solution was turbid having some undissolved/uncomplexed ibuprofen, whereas HPßCyD/ibuprofen-IC (2:1) aqueous solution was homogeneous and clear, indicating that ibuprofen was totally complexed with HPßCyD and becomes water soluble. Then, both HPßCyD/ibuprofen-IC solutions (1:1 and 2:1) were electrospun into bead-free and uniform nanofibers having ∼200 nm fiber diameter. The electrospun HPßCyD/ibuprofen-IC nanofibers were obtained as nanofibrous webs having self-standing and flexible character, which is appropriate for fast dissolving oral drug delivery systems. Ibuprofen was completely preserved during the electrospinning process, and the resulting electrospun HPßCyD/ibuprofen-IC nanofibers were produced without any loss of ibuprofen by preserving the initial molar ratio of 1:1 and 2:1 (HPßCyD/ibuprofen). X-ray diffraction and differential scanning calorimetry measurements indicated the presence of some crystalline ibuprofen in HPßCyD/ibuprofen-IC (1:1) nanofibers, whereas ibuprofen was totally in the amorphous state in HPßCyD/ibuprofen-IC (2:1) nanofibers. Nonetheless, both HPßCyD/ibuprofen-IC (1:1 and 2:1) nanofibrous webs have shown very fast dissolving character when contacted with water or when wetted with artificial saliva. In brief, our results revealed that electrospun HPßCyD/ibuprofen-IC nanofibrous webs have potential as fast dissolving oral drug delivery systems.

Functionalized Electrospun Nanofibers as Colorimetric Sensory Probe for Mercury Detection: A Review.

Mercury is considered the most hazardous pollutant of aquatic resources; it exerts numerous adverse effects on environmental and human health. To date, significant progress has been made in employing a variety of nanomaterials for the colorimetric detection of mercury ions. Electrospun nanofibers exhibit several beneficial features, including a large surface area, porous nature, and easy functionalization; thus, providing several opportunities to encapsulate a variety of functional materials for sensing applications with enhanced sensitivity and selectivity, and a fast response. In this review, several examples of electrospun nanofiber-based sensing platforms devised by utilizing the two foremost approaches, namely, direct incorporation and surface decoration envisioned for detection of mercury ions are provided. We believe these examples provide sufficient evidence for the potential use and progress of electrospun nanofibers toward colorimetric sensing of mercury ions. Furthermore, the summary of the review is focused on providing an insight into the future directions of designing electrospun nanofiber-based, metal ion colorimetric sensors for practical applications.

Immobilized Pd-Ag bimetallic nanoparticles on polymeric nanofibers as an effective catalyst: effective loading of Ag with bimetallic functionality through Pd nucleated nanofibers.

Here, we present a precise process for synthesizing Pd-Ag bimetallic nanoparticles (NPs) onto polymeric nanofibers by decorating Pd-NPs through atomic layer deposition followed by a chemical reduction process for tagging Ag nanostructures with bimetallic functionality. The results show that Pd-NPs act as a nucleation platform for tagging Ag and form Pd-Ag bimetallic NPs with a monodisperse nature with significant catalytic enhancement to the reaction rate over the bimetallic nature of the Pd-Ag ratio. A Pd-NP decorated polymeric nanofibrous web acts as an excellent platform for the encapsulation or interaction of Ag, which prevents agglomeration and promotes the interaction of Ag ions only on the surface of the Pd-NPs. We observed an effective reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) by sodium borohydride (NaBH4) to access the catalytic activity of Pd-Ag bimetallic NPs on a free-standing flexible polymeric nanofibrous web as a support. The captive formation of the polymeric nanofibrous web with Pd-Ag bimetallic functionality exhibited superior and stable catalytic performance with reduction rates of 0.0719, 0.1520, and 0.0871 min-1 for different loadings of Ag on Pd decorated nanofibrous webs such as Pd/Ag(0.01), Pd/Ag(0.03), and Pd/Ag(0.05), respectively. The highly faceted Pd-Ag NPs with an immobilized nature improves the catalytic functionality by enhancing the binding energy of the 4-NP adsorbate to the surface of the NPs. With the aid of bimetallic functionality, the nanofibrous web was demonstrated as a hybrid heterogeneous photocatalyst with a 3.16-fold enhancement in the reaction rate as compared with the monometallic decorative nature of NaBH4 as a reducing agent. The effective role of the monodisperse nature of Pd ions with an ultralow content as low as 3 wt% and the tunable ratio of Ag on the nanofibrous web induced effective catalytic activity over multiple cycles.

Nanohybrid structured RuO2/Mn2O3/CNF as a catalyst for Na-O2 batteries.

A 3D RuO2/Mn2O3/carbon nanofiber (CNF) composite has been prepared in this study by a facile two step microwave synthesis, as a bi-functional electrocatalyst towards oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). RuO2 nanoparticles with the mean size of 1.57 nm are uniformly distributed on Mn2O3 nano-rods grown on electrospun CNFs. The electrocatalytic activity of the composites are investigated towards ORR/OER under alkaline condition. The ternary RuO2/Mn2O3/CNF composite showed superior ORR activity in terms of onset potential (0.95 V versus RHE) and Tafel slope (121 mV dec-1) compared to its RuO2/CNF and Mn2O3/CNF counterparts. In the case of OER, the RuO2/Mn2O3/CNF exhibited 0.34 V over-potential value measured at 10 mA cm-2 and 52 mV dec-1 Tafel slope which are lower than those of the other synthesized samples and as compared to state of the art RuO2 and IrO x type materials. RuO2/Mn2O3/CNF also exhibited higher specific capacity (9352 mAh [Formula: see text]) than CNF (1395 mAh [Formula: see text]), Mn2O3/CNF (3108 mAh [Formula: see text]) and RuO2/CNF (4859 mAh g carbon -1) as the cathode material in Na-O2 battery, which indicates the validity of the results in non-aqueous medium. Taking the benefit of RuO2 and Mn2O3 synergistic effect, the decomposition of inevitable side products at the end of charge occurs at 3.838 V versus Na/Na+ by using RuO2/Mn2O3/CNF, which is 388 mV more cathodic compared with CNF.

Associative behaviour and effect of functional groups on the fluorescence of graphene oxide.

We have juxtaposed the structural, vibrational and emission properties of graphene oxide (GO) with various degrees of reduction with and without a model dispersant, unveiling a strong associative behavior between GO sheets and the influence of H-bonds. The interlayer spacings are ∼0.84 and 0.78 nm for the as prepared and reduced samples. -OH groups are predominantly effected by the photo-thermal reduction. Also we note some regeneration of [double bond splayed left]C[double bond, length as m-dash]O and -COOH groups in reduced samples. Clear changes to the phonon density of states indicated the doping effects due to H-bonds via the oxygeneous groups. Importantly, the defect related Raman bands are rather prone to the effect of dispersant, unveiling their intrinsic nature. In the context of fluorescence, internal vibration relaxation mediated by CC stretch vibrations emphasized the localized nature of sp2 domains of relatively smaller size. Fluorescence consists of 6 components, where the higher energy components are more influenced due to H-bonds than those of the lower energy regime, attributed to their associative behavior and chemical functionality, respectively. Excitation dependent fluorescence measurements indicated a range of optical gaps from ∼3.5 to 2 eV. The associative behavior of GO and rGO with and without a dispersant provides crucial insights into the fundamental understanding of various molecular processes.

Glucose sensors based on electrospun nanofibers: a review.

The worldwide increase in the number of people suffering from diabetes has been the driving force for the development of glucose sensors. The recent past has devised various approaches to formulate glucose sensors using various nanostructure materials. This review presents a combined survey of these various approaches, with emphasis on the current progress in the use of electrospun nanofibers and their composites. Outstanding characteristics of electrospun nanofibers, including high surface area, porosity, flexibility, cost effectiveness, and portable nature, make them a good choice for sensor applications. Particularly, their nature of possessing a high surface area makes them the right fit for large immobilization sites, resulting in increased interaction with analytes. Thus, these electrospun nanofiber-based glucose sensors present a number of advantages, including increased life time, which is greatly needed for practical applications. Taking all these facts into consideration, we have highlighted the latest significant developments in the field of glucose sensors across diverse approaches.

Ultrasensitive electrospun fluorescent nanofibrous membrane for rapid visual colorimetric detection of H2O2.

We report herein a flexible fluorescent nanofibrous membrane (FNFM) prepared by decorating the gold nanocluster (AuNC) on electrospun polysulfone nanofibrous membrane for rapid visual colorimetric detection of H2O2. The provision of AuNC coupled to NFM has proven to be advantageous for facile and quick visualization of the obtained results, permitting instant, selective, and on-site detection. We strongly suggest that the fast response time is ascribed to the enhanced probabilities of interaction with AuNC located at the surface of NF. It has been observed that the color change from red to blue is dependent on the concentration, which is exclusively selective for hydrogen peroxide. The detection limit has been found to be 500 nM using confocal laser scanning microscope (CLSM), visually recognizable with good accuracy and stability. A systematic comparison was performed between the sensing performance of FNFM and AuNC solution. The underlying sensing mechanism is demonstrated using UV spectra, transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The corresponding disappearance of the characteristic emissions of gold nanoclusters and the emergence of a localized surface plasmon resonance (LSPR) band, stressing this unique characteristic of gold nanoparticles. Hence, it is evident that the conversion of nanoparticles from nanoclusters has taken place in the presence of H2O2. Our work here has paved a new path for the detection of bioanalytes, highlighting the merits of rapid readout, sensitivity, and user-friendliness.

Review of one-dimensional and two-dimensional nanostructured materials for hydrogen generation.

Hydrogen is an attractive alternative to fossil fuels in terms of environmental and other advantages. Of the various production methods for H2, photocatalysis requires further development so that it can be applied economically on an industrial scale. One- and two-dimensional nanostructures in both pristine and modified forms have shown great potential as catalysts in the generation of H2. We review here recent developments in these nanostructure catalysts and their efficiency in the generation of H2 under UV/visible/simulated solar light. Despite much research effort, many photocatalysts do not yet meet the practical requirements for the generation of H2, such as visible light activity. H2 production is dependent on a variety of parameters and factors. To meet future energy demands, several challenges in H2 production still need to be solved. We address here the factors that influence the efficiency of H2 production and suggest alternatives. The nanostructures are classified based on their morphology and their efficiency is considered with respect to the influencing parameters. We suggest effective ways of engineering catalyst combinations to overcome the current performance barriers.

Fluorescence from graphene oxide and the influence of ionic, π-π interactions and heterointerfaces: electron or energy transfer dynamics.

2D crystals such as graphene and its oxide counterpart have sought good research attention for their application as well as fundamental interest. Especially graphene oxide (GO) is quite interesting because of its versatility and diverse application potential. However the mechanism of fluorescence from GO is under severe discussion. To explain the emission in general two interpretations were suggested, viz localization of sp(2) clusters and involvement of oxygeneous functional groups. Despite this disagreement, it should be acknowledged that the heterogeneous atomic structure, synthesis dependent and uncontrollable implantation of oxygen functional groups on the basal plane make such explanations more difficult. Nevertheless, a suitable explanation enhances the applicability of the material which also enables the design of novel materials. At this juncture we believe that given the complexity in understanding the emission mechanism it would be very useful to review the literature. In this perspective we juxtapose various results related to fluorescence and influencing factors so that a conclusive interpretation may be unveiled. Apparently, the existing interpretations have largely ignored the factors such as self-rolling, byproduct formation etc. Vis-a-vis previous reviews did not discuss the interfacial charge transfer across heterostructures and the implication on the optical properties of GO or reduced graphene oxide (rGO). Such analysis would be very insightful to determine the energetic location of sub band gap states. Moreover, ionic and π-π type interactions are also considered for their influence on emission properties. Apart from these, quantum dots, covalent modifications and nonlinear optical properties of GO and rGO were discussed for completeness. Finally we made concluding remarks with outlook.

Functionalization of cotton nonwoven with cyclodextrin/lawsone inclusion complex nanofibrous coating for antibacterial wound dressing.

Functionalizing cotton to induce biological activity is a viable approach for developing wound dressing. This study explores the development of cotton-based wound dressing through coating with biologically active nanofibers. Bioactive compounds like lawsone offer dual benefits of wound healing and infection prevention, however, their limited solubility and viability hinder their applications. To address this, Hydroxypropyl-beta-cyclodextrin (HP-ß-CD) and Hydroxypropyl-gamma-cyclodextrin (HP-γ-CD) were employed. Inclusion complexations of CD/lawsone were achieved at 2:1 and 4:1 M ratios, followed by the fabrication of CD/lawsone nanofibrous systems via electrospinning. Phase solubility studies indicated a twofold increase in lawsone water-solubility with HP-ß-CD. Electrospinning yielded smooth and uniform nanofibers with an average diameter of ∼300-700 nm. The results showed that while specific crystalline peaks of lawsone are apparent in the samples with a 2:1 M ratio, they disappeared in 4:1, indicating complete complexation. The nanofibers exhibited ∼100 % loading efficiency of lawsone and its rapid release upon dissolution. Notably, antibacterial assays demonstrated the complete elimination of Escherichia coli and Staphylococcus aureus colonies. The CD/lawsone nanofibers also showed suitable antioxidant activity ranging from 50 % to 70 %. This integrated approach effectively enhances lawsone's solubility through CD complexation and offers promise for bilayer cotton-based wound dressings.

Formulation of a fast-disintegrating drug delivery system from cyclodextrin/naproxen inclusion complex nanofibrous films.

Naproxen is a well-known non-steroidal anti-inflammatory drug (NSAID) that suffers from limited water solubility. The inclusion complexation with cyclodextrin (CD) can eliminate this drawback and the free-standing nanofibrous film (NF) generated from these inclusion complexes (ICs) can be a promising alternative formula as an orally disintegrating drug delivery system. For this, naproxen/CD IC NFs were generated using the highly water soluble hydroxypropylated derivative of ßCD (HPßCD) with two different molar ratios of 1/1 and 1/2 (drug/CD). The complexation energy calculated by the modeling study demonstrated a more favorable interaction between HPßCD and naproxen for the 1/2 molar ratio than 1/1. HPßCD/naproxen IC NFs were generated with loading concentrations of ∼7-11% and without using toxic chemicals. HPßCD/naproxen IC NFs indicated a faster and enhanced release profile in aqueous medium compared to pure naproxen owing to inclusion complexation. Moreover, rapid disintegration in less than a second was achieved in an artificial saliva environment.

Green Synthesis of Polycyclodextrin/Drug Inclusion Complex Nanofibrous Hydrogels: pH-Dependent Release of Acyclovir.

The development of an approach or a material for wound healing treatments has drawn a lot of attention for decades and has been an important portion of the research in the medical industry. Especially, there is growing interest and demand for the generation of wound care products using eco-friendly conditions. Electrospinning is one of these methods that enables the production of nanofibrous materials with attractive properties for wound healing under mild conditions and by using sustainable sources. In this study, starch-derived cyclodextrin (hydroxypropyl-ß-cyclodextrin (HPßCD)) was used both for forming an inclusion complex (IC) with acyclovir, a well-known antiviral drug, and for electrospinning of free-standing nanofibers. The nanofibers were produced in an aqueous system, without using a carrier polymer matrix and toxic solvent/chemical. The ultimate HPßCD/acyclovir-IC nanofibers were thermally cross-linked by using citric acid, listed in the generally regarded as safe (GRAS) category by the US Food and Drug Administration (FDA). The cross-linked HPßCD/acyclovir-IC nanofibers displayed stability in aqueous medium. The hydrogel-forming feature of nanofibers was confirmed with their high swelling profile in water in the range of ∼610-810%. Cellulose acetate (CA)/acyclovir nanofibers were also produced as the control sample. Due to inclusion complexation with HPßCD, the solubility of acyclovir was improved, so cross-linked HPßCD/acyclovir-IC nanofibrous hydrogels displayed a better release performance compared to CA/acyclovir nanofibers. Here, a pH-dependent release profile was obtained (pH 5.4 and pH 7.4) besides their attractive swelling features. Therefore, the cross-linked HPßCD/acyclovir-IC nanofibrous hydrogel can be a promising candidate as a wound healing dressing for the administration of antiviral drugs by holding the unique properties of CD and electrospun nanofibers.

Encapsulation of antioxidant beta-carotene by cyclodextrin complex electrospun nanofibers: Solubilization and stabilization of beta-carotene by cyclodextrins.

Carotenoids act as effective antioxidant defense systems in humans as they scavenge molecular oxygen and peroxyl radicals. However, their poor water solubility and being susceptible to degradation driven by light and oxygen hinder their bioactivity, therefore, they should be stabilized by host matrices against oxidation. Here, ß-carotene was encapsulated in electrospun cyclodextrin (CD) nanofibers to increase its water-solubility and photostability to enhance its antioxidant bioactivity. ß-carotene/CD complex aqueous solutions were electrospun into nanofibers. The bead-free morphology of the ß-carotene/CD nanofibers was confirmed by SEM. The formation of ß-carotene/CD complexes was explored through computational modeling and experimentally by FTIR, XRD and solubility tests. The antioxidant activity of the fibers exposed to UV irradiation was demonstrated via a free radical scavenger assay, where ß-carotene/CD nanofibers revealed protection against UV radiation. Overall, this work reports the water-borne electrospinning of antioxidant ß-carotene/CD inclusion complex nanofibers, which stabilize the encapsulated ß-carotene against UV-mediated oxidation.

Advances in the development of cyclodextrin-based nanogels/microgels for biomedical applications: Drug delivery and beyond.

Nanogels/microgels are swollen cross-linked polymer networks with tunable physicochemical properties and are commonly employed for the effective delivery of hydrophilic drugs. By structural engineering, they can be adapted for the delivery of hydrophobic drugs. Likewise, the use of cyclodextrins (CDs) as pharmaceutical excipients in nanogels drastically boosts the loading capacity of lipophilic drugs while enhancing their stability, bioavailability, and permeability owing to their capability of hosting drugs in their somewhat lipophilic cavity. Here, the synthesis and biomedical applications of CD-based nanogels/microgels were compiled with regard to the CD's role in nanogel synthesis. Even though most applications focused on using CD molecules as functional motifs to carry drugs and construct nanogels for biomedical applications, others used CDs in engineering nanogels to benefit from their supramolecular complexation ability. The applications of CD-based nanogels for drug-mediated cancer/tumor therapy were also discussed. Finally, the review points to the challenges/horizons to boost their biomedical applications.

Ondansetron/Cyclodextrin inclusion complex nanofibrous webs for potential orally fast-disintegrating antiemetic drug delivery.

Ondansetron (ODS) is an effective antiemetic drug which suffers from limited solubility and bioavailability during oral administration due to first-pass metabolism. However, these limitations can be mitigated through inclusion complexation with cyclodextrins (CDs). In this study, we have reported the electrospinning of polymer-free, free-standing ODS/CD nanofibrous webs (NW), a promising approach for developing a fast-disintegrating delivery system of an antiemetic drug molecule. Highly water soluble hydroxypropyl-beta-cyclodextrins (HPßCD) were used as both complexation agent and electrospinning matrix. The computational study revealed that the 1/2 (drug/CD) stoichiometry was more favorable compared to 1/1. The ODS/HPßCD NW was obtained with higher loading efficiency (∼96 %) compared to the control sample of ODS/polyvinyl alcohol (PVA) NW (∼80 %). The amorphous distribution of ODS raised by complexation and the highly water-soluble nature of HPßCD resulted into faster and better release profile and quite faster disintegration property (∼2 s) in artificial saliva than polymeric ODS/PVA NW. Here, ODS/HPßCD NW was generated in the absence of a toxic solvent or chemical to enable the drug loading in an amorphous state. From all reasons above, ODS/HPßCD NW might be a promising alternative to the polymeric based systems for the purpose of fast-disintegrating oral drug delivery.

Antibacterial nanofibers of pullulan/tetracycline-cyclodextrin inclusion complexes for Fast-Disintegrating oral drug delivery.

Tetracycline is a widely used antibiotic suffering from poor water solubility and low bioavailability. Here, hydroxypropyl-beta-cyclodextrin (HPßCD) was used to form inclusion complexes (IC) of tetracycline with 2:1 M ratio (CD:drug). Then, tetracycline-HPßCD-IC was mixed with pullulan- a non-toxic, water-soluble biopolymer - to form nanofibrous webs via electrospinning. The electrospinning of pullulan/tetracycline-HPßCD-IC was yielded into defect-free nanofibers collected in the form of a self-standing and flexible material with the loading capacity of âˆ¼ 7.7 % (w/w). Pullulan/tetracycline nanofibers was also generated as control sample having the same drug loading. Tetracycline was found in the amorphous state in case of pullulan/tetracycline-HPßCD nanofibers due to inclusion complexation. Through inclusion complexation with HPßCD, enhanced aqueous solubility and faster release profile were provided for pullulan/tetracycline-HPßCD-IC nanofibers compared to pullulan/tetracycline one. Additionally, pullulan/tetracycline-HPßCD-IC nanofibers readily disintegrated when wetted with artificial saliva while pullulan/tetracycline nanofibers were not completely absorbed by the same simulate environment. Electrospun nanofibers showed promising antibacterial activity against both gram-positive and gram-negative bacteria. Briefly, our findings indicated that pullulan/tetracycline-HPßCD-IC nanofibers could be an attractive material as orally fast disintegrating drug delivery system for the desired antibiotic treatment thanks to its promising physicochemical and antibacterial properties.

Electrospinning of polymer-free nanofibers from cyclodextrin inclusion complexes.

The electrospinning of polymer-free nanofibers from highly concentrated (160%, w/v) aqueous solutions of hydroxypropyl-ß-cyclodextrin (HPßCD) and its inclusion complexes with triclosan (HPßCD/triclosan-IC) was achieved successfully. The dynamic light scattering (DLS) and rheology measurements indicated that the presence of considerable HPßCD aggregates and the high solution viscosity were the key factors in obtaining electrospun HPßCD and HPßCD/triclosan-IC nanofibers without the use of any polymeric carrier. The HPßCD and HPßCD/triclosan-IC solutions containing 20% (w/w) urea yielded no fibers but only beads and splashes because of the depression of the self-aggregation of the HPßCD. The inclusion complexation of triclosan with HPßCD was studied by isothermal titration calorimetry (ITC) and turbidity measurements. The characteristics of the HPßCD and HPßCD/triclosan-IC nanofibers were investigated by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). It was found that the electrospinning of HPßCD/triclosan-IC solution having a 1:1 molar ratio was optimal for obtaining nanofibers without any uncomplexed guest molecules.

Electrospun polyethylene oxide (PEO) nanofibers containing cyclodextrin inclusion complex.

In this study, we obtained functional electrospun nanofibers containing stable fragrance/flavor molecule facilitated by cyclodextrin inclusion complexation. Menthol was used as a model fragrance/flavor molecule and we have electrospun poly(ethylene oxide) (PEO) nanofibers containing cyclodextrin-menthol inclusion complexes (CD-menthol-IC). We used two different solvent systems; water and water:ethanol and three types of CDs; alpha-CD, beta-CD and gamma-CD in order to find the optimal performance for the stabilization of menthol at high temperatures. We observed that the solvent system used for electrospinning process and the types of CDs (alpha-CD, beta-CD and gamma-CD) are very important to obtain CD-menthol-IC which ultimately determines the durability and temperature stability of menthol in the PEO nanofibrous web. We found out that it is better to use water rather than the water:ethanol solvent system for the inclusion complexation and additionally beta-CD and gamma-CD are most favorable choices since they are able to form complexation with menthol in the water solvent system. Despite the high volatility nature of menthol, our results demonstrated that the stability and temperature release of menthol was sustained to a very high and a broad temperature range (100 degrees C-250 degrees C) for PEO nanowebs containing CD-menthol-IC whereas the PEO nanofibers without CD and without CD-menthol complex could not preserve menthol even during storage. In brief, the results are very encouraging and open up for a variety of new exciting possibilities for the development of multi-functional electrospun nanofibers containing cyclodextrin inclusion complexes.