Towards an accurate rolling resistance: Estimating intra-cycle load distribution between front and rear wheels during wheelchair propulsion from inertial sensors.

Accurate assessment of rolling resistance is important for wheelchair propulsion analyses. However, the commonly used drag and deceleration tests are reported to underestimate rolling resistance up to 6% due to the (neglected) influence of trunk motion. The first aim of this study was to investigate the accuracy of using trunk and wheelchair kinematics to predict the intra-cyclical load distribution, more particularly front wheel loading, during hand-rim wheelchair propulsion. Secondly, the study compared the accuracy of rolling resistance determined from the predicted load distribution with the accuracy of drag test-based rolling resistance. Twenty-five able-bodied participants performed hand-rim wheelchair propulsion on a large motor-driven treadmill. During the treadmill sessions, front wheel load was assessed with load pins to determine the load distribution between the front and rear wheels. Accordingly, a machine learning model was trained to predict front wheel load from kinematic data. Based on two inertial sensors (attached to the trunk and wheelchair) and the machine learning model, front wheel load was predicted with a mean absolute error (MAE) of 3.8% (or 1.8 kg). Rolling resistance determined from the predicted load distribution (MAE: 0.9%, mean error (ME): 0.1%) was more accurate than drag test-based rolling resistance (MAE: 2.5%, ME: -1.3%).

Management of displaced humeral surgical neck fractures in daily clinical practice: hanging does not re-align the fracture.

INTRODUCTION: It is unclear if the collar and cuff treatment improve alignment in displaced surgical neck fractures of the proximal humerus. Therefore, this study evaluated if the neckshaft angle and extent of displacement would improve between trauma and onset of radiographically visible callus in non-operatively treated surgical neck fractures (Boileau type A, B, C). MATERIALS AND METHODS: A consecutive series of patients (≥ 18 years old) were retrospectively evaluated from a level 1 trauma center in Australia (inclusion period: 2016-2020) and a level 2 trauma center in the Netherlands (inclusion period: 2004 to 2018). Patients were included if they sustained a Boileau-type fracture and underwent initial non-operative treatment. The first radiograph had to be obtained within 24 h after the initial injury and the follow-up radiograph(s) 1 week after trauma and before the start of radiographically visible callus. On each radiograph, the maximal medial gap (MMG), maximal lateral gap (MLG), and neck-shaft angle (NSA) were measured. Linear mixed modelling was performed to evaluate if these measurements would improve over time. RESULTS: Sixty-seven patients were included: 25 type A, 11 type B, and 31 type C fractures. The mean age (range) was 68 years (24-93), and the mean number (range) of follow-up radiographs per patient was 1 (1-4). Linear mixed modelling on both MMG and MLG revealed no improvement during follow-up among the three groups. Mean NSA of type A fractures improved significantly from 161° at trauma to 152° at last follow-up (p-value = 0.004). CONCLUSIONS: Apart from humeral head angulation improvement in type A, there is no increase nor reduction in displacement among the three fracture patterns. Therefore, it is advised that surgical decision-making should be performed immediately after trauma. LEVEL OF CLINICAL EVIDENCE: Level IV, retrospective case series.

Shoulder kinematics and muscle activity following latissimus dorsi transfer for massive irreparable posterosuperior rotator cuff tears in shoulders with pseudoparalysis.

BACKGROUND: The aim of this study was to evaluate the thoracohumeral (TH) and glenohumeral (GH) motion with muscle activity after latissimus dorsi transfer (LDT) in a shoulder with a massive irreparable posterosuperior rotator cuff tear (MIRT) and pseudoparalysis compared with the asymptomatic contralateral shoulder (ACS). METHODS: We recruited and evaluated 13 patients after LDT in a shoulder with preoperative clinical pseudoparalysis and an MIRT on magnetic resonance imaging, with a minimum follow-up period of 1 year, and with a Hamada stage of 3 or less. Three-dimensional electromagnetic tracking was used to assess shoulder active range of motion in both the LDT shoulder and the ACS. The maximal active elevation of the shoulder (MAES) was assessed and consisted of forward flexion, scapular abduction, and abduction in the coronal plane. Maximal active internal rotation and external rotation were assessed separately. Surface electromyography (EMG) was performed to track activation of the latissimus dorsi (LD) and deltoid muscles during shoulder motion. EMG was scaled to its maximal isometric voluntary contraction recorded in specified strength tests. RESULTS: In MAES, TH motion of the LDT shoulder was not significantly different from that of the ACS (F1,12 = 1.174, P = .300) but the GH contribution was significantly lower in the LDT shoulder for all motions (F1,12 = 11.230, P = .006). External rotation was significantly greater in the ACS (26° ± 10° in LDT shoulder vs. 42° ± 11° in ACS, P < .001). The LD percentage EMG maximum showed no significant difference between the LDT shoulder and ACS during MAES (F1,11 = 0.005, P = .946). During maximal active external rotation of the shoulder, the LDT shoulder showed a higher percentage EMG maximum than the ACS (3.0% ± 2.9% for LDT shoulder vs. 1.2% ± 2.0% for ACS, P = .006). CONCLUSIONS: TH motion improved after LDT in an MIRT with pseudoparalysis and was not different from the ACS except for external rotation. However, GH motion was significantly lower after LDT than in the ACS in active-elevation range of motion. The LD was active after LDT but not more than in the ACS except for active external rotation, which we did not consider relevant as the activity did not rise above 3% EMG maximum. The favorable clinical results of LDT do not seem to be related to a change in LD activation and might be explained by its effect in preventing proximal migration of the humeral head in active elevation.

Using Wearable Sensors to Estimate Mechanical Power Output in Cyclical Sports Other than Cycling-A Review.

More insight into in-field mechanical power in cyclical sports is useful for coaches, sport scientists, and athletes for various reasons. To estimate in-field mechanical power, the use of wearable sensors can be a convenient solution. However, as many model options and approaches for mechanical power estimation using wearable sensors exist, and the optimal combination differs between sports and depends on the intended aim, determining the best setup for a given sport can be challenging. This review aims to provide an overview and discussion of the present methods to estimate in-field mechanical power in different cyclical sports. Overall, in-field mechanical power estimation can be complex, such that methods are often simplified to improve feasibility. For example, for some sports, power meters exist that use the main propulsive force for mechanical power estimation. Another non-invasive method usable for in-field mechanical power estimation is the use of inertial measurement units (IMUs). These wearable sensors can either be used as stand-alone approach or in combination with force sensors. However, every method has consequences for interpretation of power values. Based on the findings of this review, recommendations for mechanical power measurement and interpretation in kayaking, rowing, wheelchair propulsion, speed skating, and cross-country skiing are done.

Physiological and biomechanical comparison of overground, treadmill, and ergometer handrim wheelchair propulsion in able-bodied subjects under standardized conditions.

BACKGROUND: Handrim wheelchair propulsion is often assessed in the laboratory on treadmills (TM) or ergometers (WE), under the assumption that they relate to regular overground (OG) propulsion. However, little is known about the agreement of data obtained from TM, WE, and OG propulsion under standardized conditions. The current study aimed to standardize velocity and power output among these three modalities to consequently compare obtained physiological and biomechanical outcome parameters. METHODS: Seventeen able-bodied participants performed two submaximal practice sessions before taking part in a measurement session consisting of 3 × 4 min of submaximal wheelchair propulsion in each of the different modalities. Power output and speed for TM and WE propulsion were matched with OG propulsion, making them (mechanically) as equal as possible. Physiological data and propulsion kinetics were recorded with a spirometer and a 3D measurement wheel, respectively. RESULTS: Agreement among conditions was moderate to good for most outcome variables. However, heart rate was significantly higher in OG propulsion than in the TM condition. Push time and contact angle were smaller and fraction of effective force was higher on the WE when compared to OG/TM propulsion. Participants used a larger cycle time and more negative work per cycle in the OG condition. A continuous analysis using statistical parametric mapping showed a lower torque profile in the start of the push phase for TM propulsion versus OG/WE propulsion. Total force was higher during the start of the push phase for the OG conditions when compared to TM/WE propulsion. CONCLUSIONS: Physiological and biomechanical outcomes in general are similar, but possible differences between modalities exist, even after controlling for power output using conventional techniques. Further efforts towards increasing the ecological validity of lab-based equipment is advised and the possible impact of these differences -if at all- in (clinical) practice should be evaluated.

Wearable Wheelchair Mobility Performance Measurement in Basketball, Rugby, and Tennis: Lessons for Classification and Training.

Athlete impairment level is an important factor in wheelchair mobility performance (WMP) in sports. Classification systems, aimed to compensate impairment level effects on performance, vary between sports. Improved understanding of resemblances and differences in WMP between sports could aid in optimizing the classification methodology. Furthermore, increased performance insight could be applied in training and wheelchair optimization. The wearable sensor-based wheelchair mobility performance monitor (WMPM) was used to measure WMP of wheelchair basketball, rugby and tennis athletes of (inter-)national level during match-play. As hypothesized, wheelchair basketball athletes show the highest average WMP levels and wheelchair rugby the lowest, whereas wheelchair tennis athletes range in between for most outcomes. Based on WMP profiles, wheelchair basketball requires the highest performance intensity, whereas in wheelchair tennis, maneuverability is the key performance factor. In wheelchair rugby, WMP levels show the highest variation comparable to the high variation in athletes' impairment levels. These insights could be used to direct classification and training guidelines, with more emphasis on intensity for wheelchair basketball, focus on maneuverability for wheelchair tennis and impairment-level based training programs for wheelchair rugby. Wearable technology use seems a prerequisite for further development of wheelchair sports, on the sports level (classification) and on individual level (training and wheelchair configuration).

Improving Mobility Performance in Wheelchair Basketball.

OBJECTIVE: This study aimed to investigate which characteristics of athlete, wheelchair and athlete-wheelchair interface are the best predictors of wheelchair basketball mobility performance. DESIGN: A total of 60 experienced wheelchair basketball players performed a wheelchair mobility performance test to assess their mobility performance. To determine which variables were the best predictors of mobility performance, forward stepwise linear regression analyses were performed on a set of 33 characteristics, including 10 athlete, 19 wheelchair, and 4 athlete-wheelchair interface characteristics. RESULTS: A total of 8 of the characteristics turned out to be significant predictors of wheelchair basketball mobility performance. Classification, experience, maximal isometric force, wheel axis height, and hand rim diameter-which both are interchangeable with each other and wheel diameter-camber angle, and the vertical distance between shoulder and rear wheel axis-which was interchangeable with seat height-were positively associated with mobility performance. The vertical distance between the front seat and the footrest was negatively associated with mobility performance. CONCLUSION: With this insight, coaches and biomechanical specialists are provided with statistical findings to determine which characteristics they could focus on best to improve mobility performance. Six out of 8 predictors are modifiable and can be optimized to improve mobility performance. These adjustments could be carried out both in training (maximal isometric force) and in wheelchair configurations (eg, camber angle).

Development, construct validity and test-retest reliability of a field-based wheelchair mobility performance test for wheelchair basketball.

The aim of this study was to develop and describe a wheelchair mobility performance test in wheelchair basketball and to assess its construct validity and reliability. To mimic mobility performance of wheelchair basketball matches in a standardised manner, a test was designed based on observation of wheelchair basketball matches and expert judgement. Forty-six players performed the test to determine its validity and 23 players performed the test twice for reliability. Independent-samples t-tests were used to assess whether the times needed to complete the test were different for classifications, playing standards and sex. Intraclass correlation coefficients (ICC) were calculated to quantify reliability of performance times. Males performed better than females (P < 0.001, effect size [ES] = -1.26) and international men performed better than national men (P < 0.001, ES = -1.62). Performance time of low (≤2.5) and high (≥3.0) classification players was borderline not significant with a moderate ES (P = 0.06, ES = 0.58). The reliability was excellent for overall performance time (ICC = 0.95). These results show that the test can be used as a standardised mobility performance test to validly and reliably assess the capacity in mobility performance of elite wheelchair basketball athletes. Furthermore, the described methodology of development is recommended for use in other sports to develop sport-specific tests.

Effects of Offense, Defense, and Ball Possession on Mobility Performance in Wheelchair Basketball.

The aim of this study was to determine to what extent mobility performance is influenced by offensive or defensive situations and ball possession and to what extent these actions are different for the field positions. From video analysis, the relative duration of the various wheelchair movements during team offense/defense and individual ball possession was compared in 56 elite wheelchair basketball players. A two-way analysis of variance indicated that during offense, the guards and forwards performed longer driving forward than during defense. Overall, centers stood still longer during offense than during defense. Without ball, centers performed driving forward longer than with ball possession. It is concluded that offense, defense, and ball possession influenced mobility performance for the different field positions. These differences can be used to design specific training protocols. Furthermore, field positions require potentially different specific wheelchair configurations to improve performance.

Do field position and playing standard influence athlete performance in wheelchair basketball?

Improved understanding of mobility performance in wheelchair basketball is required to increase game performance. The aim of this study was to quantify the wheelchair-athlete activities of players in different field positions and of different playing standard during wheelchair basketball matches. From video analysis, absolute and relative duration and frequency of wheelchair movements and athlete control options were examined in 27 national standard and 29 international standard players during entire wheelchair basketball matches. Between-group factorial analysis of variances identified that national players drove more forward (42.6 ± 6.8 vs. 35.4 ± 3.7%; effect size Cohen's d (ES) = 1.48) and started more often driving forward (33.9 ± 2.6 vs. 31.8 ± 2.8; ES = 0.77) during a match while the mean activity duration for a single driving forward activity was longer (4.3 ± 0.9 vs. 3.7 ± 0.6 s; ES = 0.75) than for international players. Furthermore, national players performed fewer rotational movements (21.8 ± 4.0 vs. 28.9 ± 7.8%; ES = -1.30) and started less often with the rotational movements (35.0 ± 3.6 vs. 40.5 ± 5.5; ES = -1.21) while the mean activity duration for a single rotation activity was shorter (2.1 ± 0.3 vs. 2.3 ± 0.3 s; ES = -0.67) than for international players. Differences in mobility performance among guard, forward and centre players were minimal. The results should help wheelchair basketball coaches specify wheelchair-handling training techniques and means to optimise wheelchair-athlete configurations.

Early motor learning changes in upper-limb dynamics and shoulder complex loading during handrim wheelchair propulsion.

BACKGROUND: To propel in an energy-efficient manner, handrim wheelchair users must learn to control the bimanually applied forces onto the rims, preserving both speed and direction of locomotion. Previous studies have found an increase in mechanical efficiency due to motor learning associated with changes in propulsion technique, but it is unclear in what way the propulsion technique impacts the load on the shoulder complex. The purpose of this study was to evaluate mechanical efficiency, propulsion technique and load on the shoulder complex during the initial stage of motor learning. METHODS: 15 naive able-bodied participants received 12-minutes uninstructed wheelchair practice on a motor driven treadmill, consisting of three 4-minute blocks separated by two minutes rest. Practice was performed at a fixed belt speed (v = 1.1 m/s) and constant low-intensity power output (0.2 W/kg). Energy consumption, kinematics and kinetics of propulsion technique were continuously measured. The Delft Shoulder Model was used to calculate net joint moments, muscle activity and glenohumeral reaction force. RESULTS: With practice mechanical efficiency increased and propulsion technique changed, reflected by a reduced push frequency and increased work per push, performed over a larger contact angle, with more tangentially applied force and reduced power losses before and after each push. Contrary to our expectations, the above mentioned propulsion technique changes were found together with an increased load on the shoulder complex reflected by higher net moments, a higher total muscle power and higher peak and mean glenohumeral reaction forces. CONCLUSIONS: It appears that the early stages of motor learning in handrim wheelchair propulsion are indeed associated with improved technique and efficiency due to optimization of the kinematics and dynamics of the upper extremity. This process goes at the cost of an increased muscular effort and mechanical loading of the shoulder complex. This seems to be associated with an unchanged stable function of the trunk and could be due to the early learning phase where participants still have to learn to effectively use the full movement amplitude available within the wheelchair-user combination. Apparently whole body energy efficiency has priority over mechanical loading in the early stages of learning to propel a handrim wheelchair.

Trunk motion influences mechanical power estimates during wheelchair propulsion.

In wheelchair sports, there is an increasing need to monitor mechanical power in the field. When rolling resistance is known, inertial measurement units (IMUs) can be used to determine mechanical power. However, upper body (i.e., trunk) motion affects the mass distribution between the small front and large rear wheels, thus affecting rolling resistance. Therefore, drag tests - which are commonly used to estimate rolling resistance - may not be valid. The aim of this study was to investigate the influence of trunk motion on mechanical power estimates in hand-rim wheelchair propulsion by comparing instantaneous resistance-based power loss with drag test-based power loss. Experiments were performed with no, moderate and full trunk motion during wheelchair propulsion. During these experiments, power loss was determined based on 1) the instantaneous rolling resistance and 2) based on the rolling resistance determined from drag tests (thus neglecting the effects of trunk motion). Results showed that power loss values of the two methods were similar when no trunk motion was present (mean difference [MD] of 0.6 ± 1.6 %). However, drag test-based power loss was underestimated up to -3.3 ± 2.3 % MD when the extent of trunk motion increased (r = 0.85). To conclude, during wheelchair propulsion with active trunk motion, neglecting the effects of trunk motion leads to an underestimated mechanical power of 1 to 6 % when it is estimated with drag test values. Depending on the required accuracy and the amount of trunk motion in the target group, the influence of trunk motion on power estimates should be corrected for.

The ulnar collateral ligament response to valgus stress, repetitive pitching, and elbow muscle contraction in asymptomatic baseball pitchers.

Background: In baseball, repetitive pitching leads to medial elbow injuries, particularly to the ulnar collateral ligament (UCL). To prevent pitchers from UCL injuries, it is important to quantify the response to elbow stress. Repetitive elbow external valgus torque and muscular fatigue induced by repetitive pitching could affect markers of the response, that is, humeroulnar joint gap and UCL morphology. The aims of the study were three-folded: to investigate the effect of (1) exerted handgrip force on the humeroulnar joint gap, (2) repetitive pitching on the humeroulnar joint gap and the UCL morphology, and (3) exerted handgrip force on the humeroulnar joint gap for different levels of elbow valgus stress is different after compared to before repetitive pitching in asymptomatic baseball pitchers. Methods: Medial elbow ultrasound images were collected in 15 asymptomatic male baseball pitchers. Three levels of static elbow valgus stress (0N, 50N, 100N) were applied with a TELOS device before and after repetitive pitching and with or without handgrip force. These images were used to assess the humeroulnar joint gap size and UCL length and thickness. After 110 fastball pitches or when 80% self-perceived fatigue on a VAS scale was reached, participants were instructed to stop throwing. Repeated measures ANOVAs were used to statistically test significant differences. Results: Handgrip force did not significantly affect the humeroulnar joint gap. The UCL thickness and length and the humeroulnar joint gap were also not different after compared to before repetitive pitching. While higher levels of applied valgus stress significantly increased the humeroulnar joint gap (P < .001), this effect was not significantly different in the interaction with handgrip force and repetitive pitching. Conclusion: The humeroulnar joint gap changes for different levels of elbow valgus stress. However, adult baseball pitchers did not respond to elbow stress after a single pitching session with or without submaximal handgrip force in the humeroulnar joint gap and UCL morphology.

Variability in bimanual wheelchair propulsion: consistency of two instrumented wheels during handrim wheelchair propulsion on a motor driven treadmill.

BACKGROUND: Handrim wheelchair propulsion is a complex bimanual motor task. The bimanually applied forces on the rims determine the speed and direction of locomotion. Measurements of forces and torques on the handrim are important to study status and change of propulsion technique (and consequently mechanical strain) due to processes of learning, training or the wheelchair configuration. The purpose of this study was to compare the simultaneous outcomes of two different measurement-wheels attached to the different sides of the wheelchair, to determine measurement consistency within and between these wheels given the expected inter- and intra-limb variability as a consequence of motor control. METHODS: Nine able-bodied subjects received a three-week low-intensity handrim wheelchair practice intervention. They then performed three four-minute trials of wheelchair propulsion in an instrumented hand rim wheelchair on a motor-driven treadmill at a fixed belt speed. The two measurement-wheels on each side of the wheelchair measured forces and torques of one of the two upper limbs, which simultaneously perform the push action over time. The resulting data were compared as direct output using cross-correlation on the torque around the wheel-axle. Calculated push characteristics such as power production and speed were compared using an intra-class correlation. RESULTS: Measured torque around the wheel axle of the two measurement-wheels had a high average cross-correlation of 0.98 (std=0.01). Unilateral mean power output over a minute was found to have an intra-class correlation of 0.89 between the wheels. Although the difference over the pushes between left and right power output had a high variability, the mean difference between the measurement-wheels was low at 0.03 W (std=1.60). Other push characteristics showed even higher ICC's (>0.9). CONCLUSIONS: A good agreement between both measurement-wheels was found at the level of the power output. This indicates a high comparability of the measurement-wheels for the different propulsion parameters. Data from both wheels seem suitable to be used together or interchangeably in experiments on motor control and wheelchair propulsion performance. A high variability in forces and timing between the left and right side were found during the execution of this bimanual task, reflecting the human motor control process.

Magnitude and variability of individual elbow load in repetitive baseball pitching.

In baseball pitchers the elbow is exposed to high and repetitive loads (i.e. external valgus torque), caused by pitching a high number of balls in a practice session or game. This can result in overuse injuries like the ulnar collateral ligament (UCL) injury. To understand injury mechanisms, the effect of repetitive pitching on the elbow load magnitude and variability was investigated. In addition, we explored whether repetitive pitching affects elbow muscle activation during pitching. Fifteen pitchers threw each 60 to 110 balls. The external valgus torque and electromyography of three elbow muscles were quantified during each pitch. Linear mixed model analyses were performed to investigate the effect of repetitive pitching. On a group level, the linear mixed models showed no significant associations of repetitive pitching with valgus torque magnitude and variability and elbow muscle activity. Significant differences exist between pitchers in their individual trajectories in elbow valgus torque and muscle activity with repetitive pitching. This shows the importance of individuality in relation to repetitive pitching. In order to achieve effective elbow injury prevention in baseball pitching, individual characteristics of changes in elbow load and muscle activity in relation to the development of UCL injuries should be investigated.

Energy flow through the lower extremities in high school baseball pitching.

It is generally accepted that most of the energy transferred to the ball during a baseball pitch is generated in the trunk and lower extremities. Therefore, purpose of this study was to assess the energy flow through the lower extremities during a baseball pitch. It was hypothesised that the (stabilising) leading leg mainly transfers energy in a distal-to-proximal order as a kinetic chain while the (driving) trailing leg generates most energy, primarily at the hip. A joint power analysis was used to determine the rates of energy (power) transfer and generation in the ankles, knees, hips and lumbosacral joint (L5-S1) for 22 youth pitchers. Analyses showed that the leading leg mainly transfers energy upwards in a distal-to-proximal order just before stride foot contact. Furthermore, energy generation was higher in the trailing leg and primarily arose from the trailing hip. In conclusion, the legs contribute differently to the energy flow where the leading leg acts as an initial kinetic chain component and the trailing leg drives the pitch by generating energy. The actions of both legs are combined in the pelvis and passed on to the subsequent, more commonly discussed, open kinetic chain starting at L5-S1.

Shoulder muscle activity after latissimus dorsi transfer in an active elevation.

Background: After latissimus dorsi transfer (LDT), an increase in scapulothoracic (ST) contribution in thoracohumeral (TH) elevation is observed when compared to the asymptomatic shoulder. It is not known which shoulder muscles contribute to this change in shoulder kinematics, and whether the timing of muscle recruitment has altered after LDT. The aim of the study was to identify which shoulder muscles and what timing of muscle recruitment are responsible for the increased ST contribution and shoulder elevation after LDT for a massive irreparable posterosuperior rotator cuff tear (MIRT). Methods: Thirteen patients with a preoperative pseudoparalysis and MIRT were recruited after LDT with a minimum follow-up of 1 year. Three-dimensional electromagnetic tracking was used to assess maximum active elevation of the shoulder (MAES) in both the LDT and the asymptomatic contralateral shoulder (ACS). Surface electromyography (EMG) tracked activation (% EMG max) and activation timing of the latissimus dorsi (LD), deltoid, teres major, trapezius (upper, middle and lower) and serratus anterior muscles were collected. MAES was studied in forward flexion, scapular abduction and abduction in the coronal plane. Results: In MAES, no difference in thoracohumeral motion was observed between the LDT and ACS, P = .300. However, the glenohumeral motion for MAES was significantly lower in LDT shoulders F(1,12) = 11.230, P = .006. The LD % EMG max did not differ between the LDT and ACS in MAES. A higher % EMG max was found for the deltoid F(1,12) = 17.241, P = .001, and upper trapezius F(1,10) = 13.612, P = .004 in the LDT shoulder during MAES. The middle trapezius only showed a higher significant difference in % EMG max for scapular abduction, P = .020 (LDT, 52.3 ± 19.4; ACS, 38.1 ± 19.7).The % EMG max of the lower trapezius, serratus anterior and teres major did not show any difference in all movement types between the LDT and ACS and no difference in timing of recruitment of all the shoulder muscles was observed. Conclusions: After LDT in patients with a MIRT and preoperative pseudoparalysis, the LD muscle did not alter its % EMG max during MAES when compared to the ACS. The cranial transfer of the LD tendon with its native %EMG max, together with the increased %EMG max of the deltoid, middle and upper trapezius muscles could be responsible for the increased ST contribution. The increased glenohumeral joint reaction force could in turn increase active elevation after LDT in a previous pseudoparalytic shoulder.

Obtaining wheelchair kinematics with one sensor only? The trade-off between number of inertial sensors and accuracy for measuring wheelchair mobility performance in sports.

In wheelchair sports, the use of Inertial Measurement Units (IMUs) has proven to be one of the most accessible ways for ambulatory measurement of wheelchair kinematics. A three-IMU configuration, with one IMU attached to the wheelchair frame and two IMUs on each wheel axle, has previously shown accurate results and is considered optimal for accuracy. Configurations with fewer sensors reduce costs and could enhance usability, but may be less accurate. The aim of this study was to quantify the decline in accuracy for measuring wheelchair kinematics with a stepwise sensor reduction. Ten differently skilled participants performed a series of wheelchair sport specific tests while their performance was simultaneously measured with IMUs and an optical motion capture system which served as reference. Subsequently, both a one-IMU and a two-IMU configuration were validated and the accuracy of the two approaches was compared for linear and angular wheelchair velocity. Results revealed that the one-IMU approach show a mean absolute error (MAE) of 0.10 m/s for absolute linear velocity and a MAE of 8.1°/s for wheelchair angular velocity when compared with the reference system. The two-IMU approach showed similar differences for absolute linear wheelchair velocity (MAE 0.10 m/s), and smaller differences for angular velocity (MAE 3.0°/s). Overall, a lower number of IMUs used in the configuration resulted in a lower accuracy of wheelchair kinematics. Based on the results of this study, choices regarding the number of IMUs can be made depending on the aim, required accuracy and resources available.

MRI evaluation of shoulder pathologies in wheelchair users with spinal cord injury and the relation to shoulder pain.

OBJECTIVE: To describe the number, specifics and co-occurrence of shoulder pathologies detected by MRI in manual wheelchair users with spinal cord injury and to evaluate the association between shoulder pathologies and presence of shoulder pain. DESIGN: Cross-sectional observation study. SETTING: Community. PARTICIPANTS: Fifty-one wheelchair-dependent persons with spinal cord injury (44 males, 7 females, median age 50 years (IQR 14), median time since injury 24 years (IQR 16)) were allocated to pain or no-pain group based on the Wheelchair User Shoulder Pain Index. INTERVENTIONS: Not applicable. OUTCOME MEASURES: All persons underwent shoulder MRI. Pathologies were scored blinded by two experienced radiologists. Participant characteristics, number and severity of shoulder pathologies were analyzed descriptively. Logistic regression was performed to evaluate the association between MRI findings and shoulder pain. RESULTS: The median number of co-occurring MRI findings per person ranged from 0 to 19 (out of 31 possible findings). The cluster of MRI findings occurring most often together were tendon tears of supraspinatus (present in 84%), subscapularis (69%) and biceps (67%) and osteoarthritis of acromioclavicular joint (80%). When correcting for age and time since injury, the logistic regression showed no statistically significant correlation between the individual pathologies and shoulder pain. CONCLUSION: MRI findings of shoulder pathology are very frequent in persons with and without shoulder pain. Therefore, when diagnosing the cause of shoulder pain and planning interventions, health care professionals should keep this finding in mind and MRI should not be interpreted without careful consideration of clinical history and functional testing.

Influence of biomechanical models on joint kinematics and kinetics in baseball pitching.

In baseball pitching, biomechanical parameters have been linked to ball velocity and potential injury risk. However, although the features of a biomechanical model have a significant influence on the kinematics and kinetics of a motion, this influence have not been assessed for pitching. The aim of this study was to evaluate the choice of the trunk and shoulder features, by comparing two models using the same input. The models differed in thoraco-humeral joint definition (moving or fixed with the thorax), joint centre estimation, values of the inertial parameters and computational framework. One professional pitcher participated in the study. We found that the different features of the biomechanical models have a substantial influence on the kinematics and kinetics of the pitchers. With a fixed thoraco-humeral joint the peak average thorax angular velocity was delayed and underestimated by 17% and the shoulder internal rotation velocity was overestimated by 7%. The use of a thoraco-humeral joint fixed to the thorax will lead to an overestimation of the rotational power at the shoulder and will neglect the power produced by the forward and upward translation of the shoulder girdle. These findings have direct implications for the interpretation of shoulder muscle contributions to the pitch.