Acellular mineralized allogenic block bone graft does not remodel during the 10 weeks following concurrent implant placement in a rabbit femoral model.

OBJECTIVES: Due to bone loss, endosseous implants often require addition of a bone graft to support adequate primary fixation, bone regeneration, and osseointegration. The aim of this study was to compare effectiveness of autogenic and allogenic bone grafts when used during simultaneous insertion of the implant. MATERIALS AND METHODS: 4-mm-diameter rabbit diaphyseal bone autografts or allografts (n = 16/group) with a 3.2-mm pre-drilled hole in the center were placed into a 4 mm defect in the proximal femur of 3.5 kg male New Zealand White rabbits. Machined 3.2 × 10 mm grit-blasted, acid-etched titanium-aluminum-vanadium (Ti6Al4V) implants were placed. Control implants were placed into progressively drilled 3.2-mm holes in the contralateral limbs. Post-insertion day 70, samples were analyzed by micro-CT and calcified histology, or by mechanical torque and push-out testing followed by decalcified histology. RESULTS: Both grafts were integrated with the native bone. Micro-CT showed less bone volume (BV) and bone volume/total volume (BV/TV) in the allograft group, but histology showed no differences in BV or BV/TV between groups. Allograft lacked living cells, whereas autograft was cellularized. No difference was found in maximum removal torque between groups. Compressive loading at the graft-to-bone interface was significantly lower in allograft compared with autograft groups. CONCLUSIONS: There was less bone in contact with the implant and significantly less maximum compressive load in the allograft group compared with autograft. The allograft remained acellular as demonstrated by empty lacunae. Taken together, block allograft implanted simultaneously with an implant produces a poorer quality bone compared with autograft.

Neural Network Optimization of Ligament Stiffnesses for the Enhanced Predictive Ability of a Patient-Specific, Computational Foot/Ankle Model.

Computational models of diarthrodial joints serve to inform the biomechanical function of these structures, and as such, must be supplied appropriate inputs for performance that is representative of actual joint function. Inputs for these models are sourced from both imaging modalities as well as literature. The latter is often the source of mechanical properties for soft tissues, like ligament stiffnesses; however, such data are not always available for all the soft tissues nor is it known for patient-specific work. In the current research, a method to improve the ligament stiffness definition for a computational foot/ankle model was sought with the greater goal of improving the predictive ability of the computational model. Specifically, the stiffness values were optimized using artificial neural networks (ANNs); both feedforward and radial basis function networks (RBFNs) were considered. Optimal networks of each type were determined and subsequently used to predict stiffnesses for the foot/ankle model. Ultimately, the predicted stiffnesses were considered reasonable and resulted in enhanced performance of the computational model, suggesting that artificial neural networks can be used to optimize stiffness inputs.

Initial Stability of Cemented vs Cementless Tibial Components Under Cyclic Load.

BACKGROUND: Cement fixation of total knee components remains the gold standard despite resurgence in cementless fixation with the goal of long-term durable fixation. Initial stability is paramount to achieve bony ingrowth of cementless components. METHODS: Twelve cemented and cementless tibial baseplates were implanted into sawbones and tested using a physiological medial-lateral load distribution for 10,000 cycles to represent 8 weeks of in vivo function. Micromotion was measured at 5 locations around the baseplate during loading. RESULTS: Cycling had a significant effect on the change in micromotion between maximum and minimum loads at the anterior, medial, lateral, posteromedial, and posterolateral tray edge locations. A significant effect of fixation technique was detected for the anterior (P < .001), medial (P = .002), and lateral (P = .0056) locations but not for the posteromedial (P = .36) or posterolateral (P = .82) locations. Differences in micromotion between cemented and cementless components did not exceed 150 µm at any tested location. CONCLUSION: The micromotion experienced by cementless tibial components in the present study may indicate a lower initial mechanical stability than the cemented group. However, this difference in initial stability may be subclinical because the differences between average cemented and cementless micromotion were <150 µm at all measured locations under the loading regime implemented.

The Effect of Prophylactic Cerclage Wires in Primary Total Hip Arthroplasty: A Biomechanical Study.

BACKGROUND: Despite literature to support the use of various cerclage techniques to address intraoperative femoral fractures in total hip arthroplasty, there are limited data to support prophylactic cerclage wiring of the femur during cementless implant placement. This study aims to evaluate the effect of prophylactic calcar cerclage wires on the biomechanical parameters required to produce periprosthetic femoral fractures and on the morphology of these fracture patterns in stable cementless femoral implants. METHODS: Ten pairs of matched fresh frozen cadaveric femurs were implanted with anatomic tapered cementless implants with or without the addition of 2 monofilament calcar wires. Specimens were axially loaded and externally rotated to failure. Initial torsional stiffness, rotation and energy to failure, and torque at failure were measured. Statistical significance was set at P < .05. Fracture patterns were classified according to a well-known classification system. RESULTS: Wired specimens required significantly more rotation (P = .039) and energy to failure (P = .048). No significant difference was detected in initial torsional stiffness (P = .63) or torque at failure (P = .10). All unwired samples developed a Vancouver B2 fracture pattern. Seven of the 8 wired specimens also developed a Vancouver B2 fracture pattern, while the eighth wired specimen developed a Vancouver B1 fracture pattern. CONCLUSION: Prophylactic cerclage wire placement increases the rotation and energy to failure in well-fixed press-fit femoral implants. The increase in torsional energy needed for failure may reduce the risk of early periprosthetic fracture. Further studies are needed to evaluate cost vs benefit and long-term outcomes of prophylactic wiring. Based on the results of our study, consideration of prophylactic wiring should be addressed on a case-to-case basis.

Biomechanical evaluation of the risk of secondary fracture around short versus long cephalomedullary nails.

INTRODUCTION: For proximal femur fractures, long cephalomedullary nails (CMNs) are often selected to avoid a diaphyseal stress riser at the tip of a shorter nail. Secondary peri-implant fracture rates for long and short CMN have not been shown to differ clinically. This study biomechanically compares both CMN in a cadaveric model. METHODS: Ten matched pairs of cadaveric femora with short or long CMN were axially loaded and internally rotated to failure. RESULTS: Resulting fractures involved distal interlocking screws of the short and long CMN. Energy and rotation to failure were significantly greater for short CMN. Torque at failure trended higher for short CMN but not significantly. No statistical difference was detected in stiffness of the short and long CMN. DISCUSSION: A greater risk of secondary fracture is not indicated for short versus long CMN under torsional stress. Short CMN may be suitable in the younger patient.

High Risk of Surgical Glove Perforation From Surgical Rotatory Instruments.

BACKGROUND: Surgical gloves can be damaged during the course of a procedure, which can place the surgeon and patient at risk. Glove perforation may not always be readily apparent, and determining the risk factors for glove perforation can aid the surgeon in deciding when a glove change is advisable. Time of wear and needle sticks have been well studied; however, other mechanisms including mechanical stress from surgical equipment have had limited evaluation to date. QUESTIONS/PURPOSES: We evaluated the risk of glove perforation in gloves that were caught in a surgical rotatory device (such as drills and reamers). The aims of our study were (1) to determine the percentage of undetected microperforations after entanglement on a rotatory tool during orthopaedic procedures, (2) to determine which kinds of rotatory devices most commonly cause such microperforations, and (3) to assess whether time of wear had an effect on the risk of perforation. METHODS: From July 2014 to September 2015, 33 gloves were obtained from all orthopaedic subspecialties at our Level I trauma center if they were caught in a rotatory device greater than one revolution. Time of glove wear and location of the glove that was caught in a rotatory device were recorded. After an evaluation for macroperforations (≥ 5 mm), the gloves were evaluated for microperforations (< 5 mm) via the American Society for Testing and Materials (ASTM) one-liter load test. Time of wear was compared among gloves with macroperforations, microperforations, and no perforations. RESULTS: The 33 gloves obtained came from 33 procedures. Seventeen of 33 (52 %) gloves had perforations. Seven of the 17 perforated gloves had macroperforations while 10 had microperforations. Eleven of 33 entanglements were caught by drills, nine by reamers, eight by K-wires, and the remaining five gloves were caught by various other instruments. Eight of 17 perforations were caused by drills, three by reamers, three by K-wires, and three by various other instruments. The average time of wear was 58 minutes which did not differ with pattern of glove damage. CONCLUSION: Surgical gloves caught in a rotatory power instrument are likely to have been perforated, regardless of the amount of time that they had been worn. Visual inspection appears to be an inadequate test of glove integrity. When a glove becomes entangled in a rotary instrument such as a drill, pin, or reamer, a surgeon should change the gloves regardless of whether he or she believes a perforation is present. LEVEL OF EVIDENCE: Level IV, therapeutic study.

Bone-Prosthesis Junction for Active Tendon Implants: A Biomechanical Comparison of 2 Fixation Techniques.

PURPOSE: To study the biomechanical characteristics (percent stretch, stiffness, and ultimate load) of 2 distal fixation techniques for an active tendon implant used in the reconstruction of flexor tendons. METHODS: We evaluated percent stretch after cyclical loading and at failure, stiffness during load-to-failure, and peak load of 28 bone-prosthesis junctions using cadaveric canine middle phalanges to study 2 fixation techniques: metal cleat and screw versus polyester cords secured with a knot. RESULTS: The knot constructs displayed greater percent stretch during and following cyclical loading between 2 N and 50 N and at peak load. The screw construct showed greater stiffness from 50 N to 150 N during load-to-failure. Both fixation techniques failed at a mean peak load greater than 340 N. CONCLUSIONS: Both fixation techniques for active tendon implants withstood loads seen with passive and active motion in the immediate postoperative period. Knot constructs displayed significant stretch during cyclical and load-to-failure testing, which would need to be compensated for during surgery. The screw constructs showed greater stiffness than the constructs secured with the surgeon's knot, but failure created an intra-articular fracture. CLINICAL RELEVANCE: The results may aid the surgeon in choosing which fixation technique to use, during tensioning of cords, and in permitting active motion following surgery.

Does Increased Coefficient of Friction of Highly Porous Metal Increase Initial Stability at the Acetabular Interface?

BACKGROUND: Highly porous metal acetabular components illustrate a decreased rate of aseptic loosening in short-term follow-up compared with previous registry data. This study compared the effect of component surface roughness at the bone-implant interface and the quality of the bone on initial pressfit stability. The null hypothesis is that a standard porous coated acetabular cup would show no difference in initial stability as compared with a highly porous acetabular cup when subjected to a bending moment. Second, would bone mineral density (BMD) be a significant variable under these test conditions. METHODS: In a cadaveric model, acetabular cup micromotion was measured during a 1-time cantilever bending moment applied to 2 generations of pressfit acetabular components. BMD data were also obtained from the femoral necks available for associated specimen. RESULTS: The mean bending moment at 150 µm was not found to be significantly different for Gription (24.6 ± 14.0 N m) cups vs Porocoat (25 ± 10.2 N m; P > .84). The peak bending moment tolerated by Gription cups (33.9 ± 20.3 N m) was not found to be significantly different from Porocoat (33.5 ± 12.2 N m; P > .92). No correlation between BMD and bending moment at 150 µm of displacement could be identified. CONCLUSION: The coefficient of friction provided by highly porous metal acetabular shells used in this study did not provide better resistance to migration under bending load when compared with a standard porous coated component.

Vitamin C promotes wound healing through novel pleiotropic mechanisms.

Vitamin C (VitC) or ascorbic acid (AscA), a cofactor for collagen synthesis and a primary antioxidant, is rapidly consumed post-wounding. Parenteral VitC administration suppresses pro-inflammatory responses while promoting anti-inflammatory and pro-resolution effects in human/murine sepsis. We hypothesised that VitC could promote wound healing by altering the inflammatory, proliferative and remodelling phases of wound healing. Mice unable to synthesise VitC (Gulo(-/-) ) were used in this study. VitC was provided in the water (sufficient), withheld from another group (deficient) and supplemented by daily intra-peritoneal infusion (200 mg/kg, deficient + AscA) in a third group. Full thickness excisional wounds (6 mm) were created and tissue collected on days 7 and 14 for histology, quantitative polymerase chain reaction (qPCR) and Western blotting. Human neonatal dermal fibroblasts (HnDFs) were used to assess effects of In conclusion, VitC favorably on proliferation. Histological analysis showed improved wound matrix deposition and organisation in sufficient and deficient +AscA mice. Wounds from VitC sufficient and deficient + AscA mice had reduced expression of pro-inflammatory mediators and higher expression of wound healing mediators. Supplementation of HnDF with AscA induced the expression of self-renewal genes and promoted fibroblast proliferation. VitC favourably impacts the spatiotemporal expression of transcripts associated with early resolution of inflammation and tissue remodelling.

Application of a three-dimensional computational wrist model to proximal row carpectomy.

A three-dimensional (3D) computational model of the wrist examined the biomechanical effects of the proximal row carpectomy (PRC), a surgical treatment of certain wrist degenerative conditions but with functional consequences. Model simulations, replicating the 3D bony anatomy, soft tissue restraints, muscle loading, and applied perturbations, demonstrated quantitatively accurate responses for the decreased motions subsequent to the surgical procedure. It also yielded some knowledge of alterations in radiocarpal contact force which likely increase contact pressure as well as additional insight into the importance of the triangular fibrocartilage complex and retinacular/capsular structures for stabilizing the deficient wrist. As better understanding of the wrist joint is achieved, this model could serve as a useful clinical tool.

Proximal tendon-prosthesis junction for active tendon implants of the hand: a biomechanical comparison of 2 techniques.

PURPOSE: To study the biomechanical characteristics (percent stretch, stiffness, and ultimate load) of 2 tendon-prosthesis techniques used to connect the proximal tendon stump to silicone active tendon implants used in reconstruction of flexor tendons. METHODS: We evaluated percent stretch following cyclic loading and at failure, stiffness during load to failure, and ultimate load of 16 tendon-prosthesis junctions using cadaveric canine flexor digitorum profundus tendons to re-create 2 junction techniques: the tendon loop (TL) and the polyester weave (PW). RESULTS: The TL junction showed greater percent stretch at a static load of 2 N, following 500 cycles of loading between 2 N and 50 N, and at peak load. The PW junction displayed greater stiffness from 50 to 150 N during load to failure. Both junctions failed at a mean ultimate load greater than 220 N. CONCLUSIONS: The described proximal junction techniques for active tendon implants were strong enough to resist early active motion in the immediate postoperative period without significant elongation. The PW technique displayed greater stiffness and ultimate load compared with the TL. CLINICAL RELEVANCE: Data on tendon-prosthesis characteristics of these 2 methods may aid the surgeon in choosing which junction technique to use, during surgical tensioning decisions, and in considering activity protocols after surgery. These data may also serve as a baseline for further investigations regarding active tendon implants.

Biomechanical Performance of Lateral Versus Dual Locking Plates for Calcaneal Fractures.

Given the high rates of wound complications with a standard lateral extensile incision, small dual incision techniques might result in less soft tissue destruction. The goal of the present study was to compare the biomechanical performance between a single locking plate and a dual locking plating system for an intra-articular calcaneal fracture model. A Sanders IIB type joint depression calcaneal fracture was created in 10 paired, fresh-frozen, cadaveric calcanei (age 47 ± 12, range 35 to 78 years). The calcanei of each pair were randomly assigned for fixation using either a lateral locking reconstruction plate or lateral and medial locking reconstruction plates. The specimens were axially loaded in cyclic fashion for 1000 cycles, followed by load to failure. The relative fragment movement was monitored optically in both the sagittal and the coronal planes. The amount of overall construct displacement increased with cycling, although no difference was found between the plating techniques. For fragment movement during cycling, the lateral joint fragment migrated anteroinferiorly along the fracture line relative to the tuberosity fragment for dual plated specimens by a small, but statistically significant, amount. This same translation was smaller for lateral plated specimens but was not found to be significant. During load to failure testing, no statistically significant differences were found for construct stiffness. A tendency was seen toward more interfragmentary motion in the sagittal plane (lateral joint fragment movement relative to the fracture line), with less movement overall in the coronal plane (anterior fragment translation and twist) for dual plating, although the difference from the lateral plate was not statistically significant. The present study demonstrated that for this calcaneal fracture model, the dual plating technique experienced a small amount of fragment translation during cycling that was significantly different statistically from that with lateral plating but was not clinically relevant. During the load to failure, the dual plating technique was comparable to the lateral plate. Thus, dual plating could be a viable biomechanical option for fracture reduction if avoidance of a large extensile lateral approach associated with lateral plating is warranted.

Loosely implanted cementless stems may become rotationally stable after loading.

BACKGROUND: Experimental studies have suggested that initial micromotion of cementless components may lead to failure of osteointegration. Roentgen stereophotogrammetric analyses have shown durable implant fixation can be achieved long-term even when initial instability exists, as evidenced by subsidence. However improved implant stability as a result of subsidence, before osteointegration, has not been shown biomechanically. QUESTIONS/PURPOSES: We asked whether insertionally loose cementless tapered femoral stems show (1) less rotational stability (more toggle); (2) more subsidence; and (3) reduced ability to resist torsion (lower initial construct stiffness), lower torque at failure, and greater rotation to failure in comparison to well-fixed cementless tapered femoral stems. METHODS: Ten matched pairs of cadaveric femurs were implanted with well-fixed and loose cementless tapered stems. The loose stem construct was obtained by appropriately broaching the femur but afterwards inserting a stem one size smaller than that broached. Femoral stem rotational stability of implanted femurs was tested by measuring the angular rotation (ie, toggle) required to produce a torque of 2 N-m at 0 N, 250 N, and 500 N vertical load in 25° adduction simulating single-legged stance. Subsidence was measured as vertical movement during the toggle tests. Then at 500 N initial vertical load, femoral stems were externally rotated to failure. The construct stiffness between 5 and 40 N-m was determined to assess ability to resist torsion. The torque and rotation to failure were recorded to compare failure characteristics. Groups were compared using mixed model ANOVA followed by Tukey-Kramer post hoc pairwise comparison for toggle and subsidence tests and by Student's paired t-tests for stiffness, torque at failure, and rotation to failure tests. RESULTS: Loose tapered cementless stems were less stable (ie, more toggle) than well-fixed at 0 N of load (p < 0.0001), but no difference was detectable in toggle between loose and well-fixed stems at 250 N (p = 0.7019) and 500 N (p = 0.9970). Loose tapered cementless stems showed significant subsidence at 250 N (p < 0.0001) and 500 N (p < 0.0001), which was not found in the well-fixed stems at 250 N (p = 0.8813) and 500 N (p = 0.1621). Torsional stiffness was lower for loose stems as compared with well-fixed stems (p = 0.0033). No difference in torque at failure (p = 0.7568) or rotation to failure (p = 0.2629) was detected between loose and well-fixed stems. CONCLUSIONS: In this study, we observed that insertionally loose cementless stems have the ability to subside and become rotationally stable with loading. They did not exhibit a lower torque or rotation to failure in comparison to well-fixed stems when under simulated single-legged stance. CLINICAL RELEVANCE: Secondary rotational stabilization may prevent insertionally loose tapered stems from producing a stress pattern that predisposes to early postoperative periprosthetic fracture around loose cemented stems.

Reattachment of flexor digitorum profundus avulsion: biomechanical performance of 3 techniques.

PURPOSE: To investigate whether inclusion of the volar plate in repair of flexor digitorum profundus avulsions increases the strength of the repair and resists gapping. METHODS: Cadaveric fingers (n = 18) were divided into 3 equal groups. The first technique involved 2 micro-suture anchors only (A). The second used only volar plate repair (VP). The third group was a hybrid, combining a micro-suture anchor with volar plate augmentation (AVP). Specimens were loaded cyclically to simulate passive motion rehabilitation before being loaded to failure. Clinical failure was defined as 3 mm of gapping, and physical failure as the highest load associated with hardware failure, suture breakage, anchor pullout, or volar plate avulsion. RESULTS: Gapping throughout cycling was significantly greater for the A group than VP and AVP with no difference detected between VP and AVP groups. Gapping exceeded 3 mm during cycling of 3 A specimens, but in none of the VP or AVP specimens. Load at clinical and physical failure for A was significantly lower than for VP and AVP, whereas no difference was detected between VP and AVP. CONCLUSIONS: In this cadaveric model, incorporating the volar plate conferred a significant advantage in strength, increasing the mean load to physical failure by approximately 100 N. CLINICAL RELEVANCE: According to previous biomechanical studies, current reconstructive strategies for flexor digitorum profundus zone I avulsions are not strong enough to withstand active motion rehabilitation. We demonstrated the potential use of volar plate augmentation and the prospective advantageous increase in strength in this cadaveric model. In vivo performance and effects on digital motion are not known.

Initial stability of press-fit acetabular components under rotational forces.

The primary goal of this study was to determine the initial press-fit stability in acetabular components without screw fixation. Mechanical testing was performed with the implantation of press-fit acetabular components in cadaveric specimens. No significant difference was found in load to failure testing between 1 and 2 mm of under-reaming. However, there was significant variability in bending forces required to create 150 µm of micromotion ranging from 49.3 N to 214.4 N. This study shows that cups implanted in a press-fit fashion, which are felt to be clinically stable, have high degrees of variability in resisting load and may be at risk for loosening. There is a need for more objective intra-operative techniques to test cup stability.

Effect of restoration volume on stresses in a mandibular molar: a finite element study.

STATEMENT OF PROBLEM: There can be significant disagreement among dentists when planning treatment for a tooth with a failing medium-to-large--sized restoration. The clinician must determine whether the restoration should be replaced or treated with a crown, which covers and protects the remaining weakened tooth structure during function. PURPOSE: The purpose of this study was to evaluate the stresses generated in different sized amalgam restorations via a computational modeling approach and reveal whether a predictable pattern emerges. MATERIAL AND METHODS: A computer tomography scan was performed of an extracted mandibular first molar, and the resulting images were imported into a medical imaging software package for tissue segmentation. The software was used to separate the enamel, dentin, and pulp cavity through density thresholding and surface rendering. These tissue structures then were imported into 3-dimensional computer-aided design software in which material properties appropriate to the tissues in the model were assigned. A static finite element analysis was conducted to investigate the stresses that result from normal occlusal forces. Five models were analyzed, 1 with no restoration and 4 with increasingly larger restoration volume proportions: a normal-sized tooth, a small-sized restoration, 2 medium-sized restorations, and 1 large restoration as determined from bitewing radiographs and occlusal surface digital photographs. RESULTS: The resulting von Mises stresses for dentin-enamel of the loaded portion of the tooth grew progressively greater as the size of the restoration increased. The average stress in the normal, unrestored tooth was 4.13 MPa, whereas the smallest restoration size increased this stress to 5.52 MPa. The largest restoration had a dentin-enamel stress of 6.47 MPa. A linear correlation existed between restoration size and dentin-enamel stress, with an R(2) of 0.97. CONCLUSIONS: A larger restoration volume proportion resulted in higher dentin-enamel stresses under static loading. A comparison of the von Mises stresses to the yield strengths of the materials revealed a relationship between a tooth's restoration volume proportion and the potential for failure, although factors other than restoration volume proportion may also impact the stresses generated in moderate-sized restorations.

Plantar measurements to determine success of surgical correction of Stage IIb adult acquired flatfoot deformity.

Adult acquired flatfoot deformity is a degenerative disease causing medial arch dysfunction. Surgical correction has typically involved tendon reconstruction with calcaneal osteotomy; however, the postoperative changes have not been fully characterized. The present study assessed the success of surgical correction of Stage IIb adult acquired flatfoot deformity through changes in plantar pressures and patient-generated outcome scores. With Institutional Review Board approval, 6 participants were evaluated before and after surgery using pedobarography, the Foot and Ankle Outcome Score, and the Medical Outcomes Study 36-item short-form questionnaire. The plantar pressures were recorded using a TekScan HRMat(®) during walking and in a 1- and 2-foot stance. The resulting contour maps were segmented into 9 regions, with the peak pressure, normalized force, and arch index calculated. Surgical effects were analyzed using paired t tests. Postoperatively, the Foot and Ankle Outcome Score and Medical Outcomes Study 36-item short-form questionnaire scores increased significantly from 180 ± 78 to 360 ± 136 (p < .03) and 47 ± 18 to 71 ± 19 (p = .06), respectively. During the 2-foot stance, the normalized force had increased significantly in the lateral midfoot (p < .03), although no significant differences were found in peak pressures. No significant differences were observed in the 1-foot stance. During walking, the normalized force increased significantly in the lateral mid- and forefoot (p < .05). The peak pressure increased significantly in the lateral forefoot (p < .01). The arch index values demonstrated no significant changes. The increased questionnaire scores indicated that surgical correction improved the self-perceived health of the participants. Lateral shifts in the peak pressure and normalized force suggest that forefoot and midfoot loading is altered postoperatively, consistent with the goal of offloading the dysfunctional arch. Thus, the present study has demonstrated that surgical treatment of adult acquired flatfoot deformity can be accurately assessed using patient-reported outcome measures and plantar pressures.

Unicortical PEEK inset locking fixation for metacarpal fractures: a biomechanical study.

PURPOSE: There are numerous constructs employed in the treatment of metacarpal fractures with varying degrees of success. While plate fixation commonly involves dorsal application of a bicortical non-locking plate, there has been recent exploration of other fixation options including unicortical locked plating. The purpose of this study was to evaluate the biomechanical integrity of a polyetheretherketone (PEEK) inset locking plate and, in doing so, compare it to standard plate fixation (utilizing a clinically proven bicortical non-locking titanium plate) in a simulated porcine metacarpal fracture model. METHODS: Reproducible mid-shaft fractures were created in porcine second metacarpals. The fractured specimens were reduced and plated with either a bicortical non-locking plate or a unicortical locking plate with a PEEK locking design. Constructs were then loaded to failure in the same fashion as performed to create the fracture. Peak load was measured as the apex on the load-to-failure deflection curve. Stiffness was calculated as the linear slope on the load-to-failure deflection curve. Data were analyzed via Student's t test. RESULTS: Unicortical locking constructs failed at 344 ± 119 N, while bicortical non-locking constructs were found to fail at 277 ± 101 N (p = 0.19). The unicortical locking constructs demonstrated a stiffness of 80 ± 36 N/mm compared with the bicortical non-locking constructs (69 ± 36 N/mm) although again the difference was not found to be statistically different (p = 0.49). CONCLUSION: Based on this study, a locked plating construct using a polymer mechanism provides an interesting new locking fixation method for small bone fractures and with our limited number of specimens tested, provided at least a similar strength and rigidity profile in comparison with bicortical fixation in the treatment of metacarpal fractures.

Proximal humeral fracture fixation: a biomechanical comparison of two constructs.

BACKGROUND: Different options exist for stabilizing proximal humeral fractures. This study compared the mechanical stability of 2 common proximal humeral fixation plates in bending and torsion. METHODS: Tests were conducted on 40 synthetic and 10 matched pairs of cadaveric humeri (evenly fixed with DePuy S3 proximal humeral plating system [DePuy Orthopaedics, Warsaw, IN, USA] and Synthes proximal humerus locking compression plate [Synthes, Paoli, PA, USA]). Half of the humeri were tested by cantilevered bending in flexion, extension, varus, and valgus for 100 cycles of ±5 mm of displacement at 1 mm/s before loading to failure in varus. The other half were tested in torsion for 100 cycles of ±8° of rotational displacement at 1°/s before loading to failure in external rotation. RESULTS: Peak cyclic loads for synthetic constructs were higher for DePuy plates than Synthes plates in varus and valgus (P < .0001), but a difference was not detected in extension (P > .40) or flexion (P = .0675). Peak cyclic loads for cadaveric constructs showed a significant difference in extension and flexion (Synthes > DePuy, P < .0001) and in varus (DePuy > Synthes, P < .05) but not in valgus (P > .10). Bending stiffness during varus failure testing was higher for DePuy plates than Synthes plates (P < .0001) for synthetic constructs. Regarding torsion of synthetic and cadaveric constructs, DePuy plates experienced higher peak cyclic torques over all cycles in both directions (P < .0001). For synthetic constructs, DePuy plates showed higher torsional stiffness in external failure than Synthes plates (P < .0001). CONCLUSIONS: The DePuy plate was stiffer than the Synthes plate with varus and valgus bending, as well as in torsion. The Synthes plate tended to be stiffer in flexion and extension.