Fabrication and Characterization of a High-Strength Polyimide/Thermoplastic Polyurethane Composite Aerogel with Hydrophobicity and Low Thermal Conductivity.

Polyimide (PI) aerogel has surfaced in research and development as a result of its heat resistance, flame retardancy, and low dielectric constant. However, it is still a challenge to reduce the thermal conductivity while improving its mechanical strength and retaining hydrophobicity. Herein, the PI/thermoplastic polyurethane (TPU) composite aerogel was synthesized by coupling TPU with PI via a novel method of chemical imidization combined with freeze-drying technology. With this technique, PI aerogel with excellent comprehensive performance is produced. Interestingly, the volume shrinkage of the composite aerogel decreased from 24.14 to 5.47%, which leads to low density (0.095 g/cm3) and elevated porosity (92.4%). In addition, strong mechanical strength (1.29 MPa) and high hydrophobicity (123.6°) were achieved. More importantly, PI/TPU composite aerogel demonstrated a low thermal conductivity of 29.51 mW m-1 K-1 at ambient temperature. Therefore, PI/TPU composite aerogel can be a promising material for hydrophobic and thermal insulation applications.

Z-scheme polyimide/tungsten trioxide aerogel photocatalyst for enhanced photocatalytic CO2reduction under visible light.

Developing highly efficient and stable photocatalysts is an effective method to achieve CO2photocatalytic reduction. Herein, PI/WO3aerogel photocatalyst was prepared by chemical amide reaction coupled with an ethanol supercritical drying technique. The novel aerogel photocatalysts exhibit excellent photocatalytic performance for reducing CO2into CO. In particular, PI/WO3-10 aerogel photocatalyst shows the highest yield of CO (5.72µmol g-1h-1), which is ca 11-fold higher than that of the pristine PI aerogel. The high CO2reduction activity can be attributed to the Z-scheme structure, which enhances the separation of photo-generated electron-holes, and induces H2O oxidation on WO3nanosheets and CO2reduction on PI aerogel. The photocatalytic reaction mechanism of CO2when using PI/WO3aerogel photocatalyst is proposed.

Highly efficient visible-light-induced photoactivity of carbonized polyimide aerogel for antibiotic degradation.

Various nitrogen (N)-doped carbon materials have been designed as efficient photocatalysts. For the first time, polyimide (PI) aerogels were calcined to be N-doped carbon photocatalysts at different temperatures. The structures of the carbonized polyimide aerogels (CPIs) vary with the carbonization temperature. The conductivity of the CPI increases with the improvement of calcination temperature, whereas the N content of the CPI decreases and the N state also changes. Thus, the electronic properties of the CPI are changed. The photocatalytic experiments certified that the PI aerogel calcined at 800 °C exhibited the highest photocatalytic performance. The chlortetracycline (CTC) degradation rate over CPI-800 aerogel is 2.3 times as much as that of PI aerogel due to the changed structure and properties of the CPI-800 aerogel.

Surface Modification of Polyimide Aerogel by Thermoplastic Polyurethane for Enhanced Mechanical Strength and Thermal Insulation Performance.

Polyimide (PI) aerogel is a good thermal insulation material with the highest temperature resistance in practical application. But the mechanical strength of PI aerogels prepared by freeze-drying or thermoimide methods is weak. In this research, TPU was selected as an aging solution to solve the problem of the low mechanical strength of PI aerogel prepared by the freeze-drying method. Previous work has certified that the coupling of PI and thermoplastic polyurethane (TPU) can enhance the mechanical strength of PI aerogel to a certain extent due to the flexibility of TPU. But excessive TPU will change the PI structure in the cross-linking process and decrease the mechanical strength of the aerogel. Thus, a new kind of PI gel modification method was provided by using TPU as an aging solution, and the mechanical strength of PI aerogel is improved to 3.06 MPa. Furthermore, the shrinkage, specific surface area, waterproof angle, and thermal conductivity all show good performance, thus enabling PI aerogel to be used in many aspects. Specially, the method is simple and can be used to prepare some other high-strength aerogels.

A multifunctional PAN/PVP nanofiber sponge wound dressing loaded with ZIF-8-derived carbon nanoparticles with adjustable wetness for rapid wound disinfection and exudate management.

Rapid and safe disinfection and exudate management are two major challenges in infected wound care. Therefore, in this work, we developed a novel wound dressing via encapsulating ZIF-8-derived carbon nanoparticles in a hydrophilic nanofiber sponge to address severe wound infection and heavy exudate problems. The dressing can effectively kill bacteria through chemo-photothermal synergistic therapy. Meanwhile, the hydrophilic nanofiber sponge can quickly absorb wound exudate around the wound and accelerate the evaporation rate of liquid through the photothermal effect and its own structure; therefore, it is possible to remove excess liquid and regulate its wetness. In this way, it prevents the problem of wound overhydration often caused by hydrophilic dressings. In our experiment, the dressing showed good antibacterial performance and biocompatibility in vitro and could effectively control wound infection, absorb wound exudate and promote skin wound healing in vivo. Its good therapeutic effect is not only due to effective infection control and wound exudate management, but also because the structure of nanofibers similar to an extracellular matrix provides basic physical support and structural  signals conducive to skin tissue regeneration.

Sodium Alginate-Based Carbon Aerogel-Supported ZIF-8-Derived Porous Carbon as an Effective Adsorbent for Methane Gas.

Adsorption natural gas (ANG) is a technology in which natural gas is stored on the surface of porous materials at relatively low pressures, which are promising candidates for adsorption of natural gas. Adsorbent materials with a large surface area and porous structure plays a significant role in the ANG technology, which holds promise in increasing the storage density for natural gas while decreasing the operating pressure. Here, we demonstrate a facile synthetic method for rational construction of a sodium alginate (SA)/ZIF-8 composite carbon aerogel (AZSCA) by incorporating ZIF-8 particles into SA aerogel through a directional freeze-drying method followed by the carbonization process. The structure characterization shows that AZSCA has a hierarchical porous structure, in which the micropores originated from MOF while the mesopores are derived from the three-dimensional network of the aerogel. The experimental results show that AZSCA achieved high methane adsorption of 181 cm3·g-1 at 65 bar and 298 K, along with higher isosteric heat of adsorption (Qst) throughout the adsorption range. Thus, the combination of MOF powders with aerogel can find potential applications in other gas adsorption.

Carboxymethyl cellulose/polyvinyl alcohol composite aerogel supported beta molecular sieve for CH4 adsorption and storage.

Biomass aerogel is attractive in various applications due to their renewable, biodegradable and eco-friendly advantages. Herein, a novel beta molecular sieve/carboxymethyl cellulose/polyvinyl alcohol composite aerogel (beta/CP) is prepared by direct mixing and directional freeze-drying as an efficient gas adsorbent with hierarchical porosity. The beta molecular sieve is uniformly dispersed in the three-dimensional skeleton of the aerogel. By adjusting the loading mass of the beta molecular sieve to constitute a reasonable porosity and pore size distribution, the synergistic effect between pore structures of different scales improves the adsorption performance. The experiment results of beta/CP-4 show that the CH4 adsorption capacity can reach 60.33 cm3/g at 298 K and 100 bar, which is almost the same as that of the pure beta molecular sieve (62.09 cm3/g). The strong interaction between the aerogel and it prevents the molecular sieve agglomeration, improves the pore utilization, and also reduces the cost of using molecular sieve adsorbent. The above results indicate that the composite has good potential for application in the field of CH4 storage.

Particle size optimization of metal-organic frameworks for superior capacitive deionization in oxygenated saline water.

Pyrolysis-free metal-organic frameworks (MOFs) with optimized particle sizes were used as capacitive deionization (CDI) materials in oxygenated saline water. Upon decreasing the particle size of the MOFs, excellent cycling stability and higher CDI performance were achieved. This was possibly due to the improvement in charge transfer and electrolyte permeation, uncovering the significance of particle size control in improving CDI performance.

A single dual-targeting fluorescent probe enables exploration of the correlation between the plasma membrane and lysosomes.

The interactions between organelles can maintain normal cell activity. Lysosomes, as waste disposal systems of cells, have many important interactions with the plasma membrane, especially in the repair of cracked plasma membrane. Unfortunately, a way to study the relationship between them synchronously is still lacking. Therefore, in this work, we constructed a dual-targeting probe (Mem-Lyso) to simultaneously visualize the plasma membrane and lysosomes for the first time. Taking advantage of dual-targeting, the probe Mem-Lyso could successfully track and analyze the dynamic changes of the plasma membrane and lysosomes in different bioprocesses. The experimental results demonstrated that, compared to the normal status, there was obvious fusion between the plasma membrane and lysosomes in the apoptosis process. Furthermore, because of the sensitivity to polarity, Mem-Lyso could label the plasma membrane and lysosomes with red and yellow colors in cells, respectively. Moreover, the skeleton and gastrointestinal wall of zebrafish were visualized by dual-color imaging, respectively. More importantly, the dual-targeting property endowed Mem-Lyso with the ability to spatially distinguish the cholesterol (CL) content in the plasma membrane, which provided a potential detection tool for biological research and diagnosis of related diseases.

Carbon Aerogels as Electrocatalysts for Sustainable Energy Applications: Recent Developments and Prospects.

Carbon aerogel (CA) based materials have multiple advantages, including high porosity, tunable molecular structures, and environmental compatibility. Increasing interest, which has focused on CAs as electrocatalysts for sustainable applications including oxygen reduction reaction (ORR), oxygen evolution reaction (OER), hydrogen evolution reaction (HER), and CO2 reduction reaction (CO2RR) has recently been raised. However, a systematic review covering the most recent progress to boost CA-based electrocatalysts for ORR/OER/HER/CO2RR is now absent. To eliminate the gap, this critical review provides a timely and comprehensive summarization of the applications, synthesis methods, and principles. Furthermore, prospects for emerging synthesis, screening, and construction methods are outlined.

Konjac glucomannan/cellulose nanofibers composite aerogel supported HKUST-1 for CO2 adsorption.

Biomass aerogels are attractive in various applications owing to their inherent advantages of renewability, biodegradability and eco-friendly. Herein, a novel composite aerogel of konjac glucomannan (KGM)/TEMPO-oxidized cellulose nanofibers (TOCNF)@HKUST-1 (KTA@HKUST-1) is prepared through a facile vacuum impregnation method combined with the directional freeze-drying process, which using KGM and TOCNF as raw materials. The structural analyses disclose that the KTA@HKUST-1 has a hierarchical porosity, in which HKUST-1 can provide micropores for adsorption, while the meso-/macropores from KTA act as high-speed channels to improve diffusion and mass transfer rate to transport CO2 components into the micropores of HKUST-1. The experiment results of KTA@HKUST-1-10 (KTA@H10) show that the CO2 adsorption capacity can reach 3.50 mmol·g-1 at 1 bar and 298 K, and the adsorption capacity retention rate as high as 91.43% after 7 cycles. In addition, the CO2/N2 adsorption selectivity of KTA@H10 can reach 18.42, which has an excellent potential for selective CO2 adsorption.

Preparation and Properties of the Urea-Formaldehyde Res-In/Reactive Halloysite Nanocomposites Adhesive with Low-Formaldehyde Emission and Good Water Resistance.

Low-cost urea formaldehyde resin (UF)/reactive halloysite nanotubes (HNTs) nanocomposite adhesive was prepared successfully via in situ polymerization. The HNTs were modified to improve its compatibility with polymer. The XRD and FTIR results showed that physical and chemical interaction between the HNTs and polymer resin influenced the structure of UF owing to the functional groups on the HNTs. It is found from SEM images that the modified HNTs could be dispersed uniformly in the resin and the nanocomposite particles were spherical. The performance experiment confirmed that thermal stability of nanocomposite increased largely, formaldehyde emission of UF wood adhesive reduced 62%, and water resistance of UF wood adhesive improved by 84%. Meanwhile, the content of HNTs on the nanocomposites could be up to 60 wt %. The mechanism of the nanocomposites based on the reactive HNTs was proposed. The approach of the preparation could supply an idea to prepare other polymer/clay nanocomposites.

Nitrogen-doped carbon composite derived from ZIF-8/polyaniline@cellulose-derived carbon aerogel for high-performance symmetric supercapacitors.

Cellulose derived carbon aerogel (CA) with unique three-dimensional network coated with polyaniline (PANI) on its surface is used as a scaffolding framework to anchor ZIF-8. The designed ZIF-8 derived porous carbon (ZC)/PANI@CA (ZPCA) hybrid carbon composite through a facile solution immersion chemical route and subsequent carbonization process is employed as electrode for supercapacitor, which has contributed a large specific surface area, a hierarchical porous structure and reasonable N content (up to 6.27 at.%). The synthesized ZPCA electrode achieves an outstanding capacitance of 388 F g-1 at 0.5 A g-1 as well as an excellent cycling performance. More inspiringly, the symmetric supercapacitor based ZPCA achieves a high energy density of 13.4 Wh kg-1 at a power density of 250 W kg-1 using 2 M KOH aqueous solution, and an ultrahigh energy density of 81.8 Wh kg-1 at a power density of 950 W kg-1 is realized using Et4NBF4/AN electrolyte.

Preparation and Property of Bio-Polyimide/Halloysite Nanocomposite Based on 2,5-Furandicarboxylic Acid.

Bio-based polyimide (PI)/halloysite nanotube (HNT) nanocomposites based on 2,5-furandicarboxylic acid were prepared by in situ polymerization. The pristine HNTs were modified by tetraethoxysilane (TEOS) and 4,4'-oxybisbenzenamine (ODA). The bio-based PI/HNT nanocomposite film exhibited lower moisture absorption than pure bio-based polyimide, showing that the water resistance of the bio-based polyimide film was improved. The thermal stability and glass transition temperature (Tg) of PI/HNTs nanocomposites were improved with the addition of modified HNTs. Both the tensile strength and Young's modulus of bio-based PI/HNTs nanocomposite films were enhanced. A 37.7% increase in tensile strength and a 75.1% increase in Young's modulus of bio-based PI/HNTs nanocomposite films, with 1 wt% of the modified HNTs, were achieved. The result confirmed that 2,5-furandicarboxylic acid could replace the oil-based material effectively, thus reducing pollution and protecting the environment. Finally, a preparation mechanism to prepare bio-based PI/HNTs nanocomposite is proposed.

High-performance asymmetric supercapacitor made of NiMoO4 nanorods@Co3O4 on a cellulose-based carbon aerogel.

In this study, a new nanoporous material comprising NiMoO4 nanorods and Co3O4 nanoparticles derived from ZIF-67 supported by a cellulose-based carbon aerogel (CA) has been successfully synthesized using a two-step hydrothermal method. Due to its chemical composition, the large specific surface and the hierarchical porous structure, the NiMoO4@Co3O4/CA ternary composite yields electrodes with an enhanced specific capacitance of 436.9 C/g at a current density of 0.5 A/g and an excellent rate capability of 70.7% capacitance retention at 5.0 A/g. Moreover, an advanced asymmetric supercapacitor (ASC) is assembled using the NiMoO4@Co3O4/CA ternary composite as the positive electrode and activated carbon as the negative electrode. The ASC device exhibits a large capacitance of 125.4 F/g at 0.5 A/g, a maximum energy density of 34.1 Wh/kg at a power density of 208.8 W/kg as well as a good cyclic stability (84% after 2000 cycles), indicating its wide applicability in energy storage. Finally, our results provide a general approach to the construction of CA and MOF-based composite materials with hierarchical porous structure for potential applications in supercapacitors.

A Z-Scheme Polyimide/AgBr@Ag Aerogel with Excellent Photocatalytic Performance for the Degradation of Oxytetracycline.

A novel Z-scheme polyimide (PI)/AgBr@Ag aerogel photocatalyst has been successfully synthesized by combining an in situ precipitation method and a supercritical drying method. The as-prepared PI/AgBr@Ag-50 (50 wt % AgBr@Ag in PI/AgBr@Ag) aerogel photocatalyst exhibited excellent photocatalytic activity for oxytetracycline degradation with a rate constant of 0.025 min-1 , which was 6.9 and 2.6 times higher than that of the PI aerogel or the AgBr@Ag nanoparticles, respectively. More significantly, the PI/AgBr@Ag-50 aerogel photocatalyst showed stable cycling, which could be attributed to the high mechanical strength and 3D network of the PI aerogel. The introduction of AgBr@Ag on PI with a heterojunction structure efficiently promoted the separation of electron-hole pairs by a Z-scheme mechanism. The reduced metallic Ag nanoparticles were found to function as centers for the transfer of electrons from AgBr to PI. This work has revealed a new application for the aerogel PI/AgBr@Ag photocatalyst in environmental protection.

Monolithic zirconia aerogel from polyacetylacetonatozirconium precursor and ammonia hydroxide gel initiator: formation mechanism, mechanical strength and thermal properties.

Zirconia (ZrO2) aerogels are potential candidates for use at temperatures higher than those attainable with silica aerogels. However, fabricating a robust ZrO2 aerogel with a high thermal stability is still a challenge. The extreme electronegativity of Zr makes the hydrolysis and polycondensation of zirconium precursors difficult to control, leading to poor structural integrity and unsatisfactory physical properties. In the present research, we prepared a ZrO2 aerogel by using a synthetic zirconium precursor, namely polyacetylacetonatozirconium (PAZ), and ammonia hydroxide as the gel initiator. The ammonia hydroxide catalyzes the cross-linking of PAZ via promotion of the dehydration between hydroxyls in PAZ and the acetylacetonate group in PAZ binds the zirconium ion firmly upon the addition of ammonia hydroxide to avoid a gel precipitate. A monolithic ZrO2 aerogel with a large diameter size of 4.4 cm and high optical transmittance was achieved after drying. The surface area and pore volume of the as-dried ZrO2 aerogel were as high as 630.72 m2 g-1 and 5.12 cm3 g-1, respectively. They decreased to 188.62 m2 g-1 and 0.93 cm3 g-1 after being heat-treated at 1000 °C for 2 h. The best mechanical performances of the ZrO2 aerogels showed a compressive strength of 0.21 ± 0.05 MPa and a modulus of 1.9 ± 0.3 MPa with a density of 0.161 ± 0.008 g cm-3. Both pore structures and mechanical performances varied according to the ammonia hydroxide gel initiator used. The thermal insulating properties of the ZrO2 aerogel performed better than a silica aerogel blanket with a thermal conductivity of 0.020 W (m-1 K-1).

[Determination of anthocyanins in the peel of sweet cherry by ultra performance liquid chromatography tandem mass spectrometry].

A method for the determination of seven anthocyanins in the peel of sweet cherry was developed by ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The sample was extracted by methanol containing 0.1% (v/v) hydrochloric acid, and then purified by AB-8 macroporous resins. The separation was carried out on a Phenomenex Kinetex column (100 mm x 4.6 mm, 2.6 Rm) with mobile phase of 0.1% (v/v) formic acid aqueous solution containing 5 mmol/L ammonium formate and methanol. The sample solution was detected by UPLC-MS/MS with ESI under positive ion and multi reaction monitoring (MRM) modes. The results showed that the limits of quantification (LOQs) for the seven target compounds were 0.26-1.42 µg/kg. The seven anthocyanin standards showed a good linearity in the range of 0-100 µg/L with the correlation coefficients (r2) of 0.996 4-0.999 3. The average recoveries of the seven anthocyanins were 97.2%-105.4%, and the relative standard deviations (RSDs) were 1.9%-5.8%. The mature fruit samples of sweet cherry red variety "Tieton" and the yellow variety "13-33" were analyzed by this method. The results showed that the anthocyanin composition and contents were significantly different between the two varieties. This method can be used for rapid identification and the determination of anthocyanin components in sweet cherry fruits due to its simple operation, high sensitivity, good reproducibility and covering a wide range of anthocyanins.