RESUMEN
CO2 hydrogenation to methane is gaining increasing interest as one of the most promising ways to store intermittent renewable energy in the form of chemical fuels. Ni particles supported on CeO2 represent a highly efficient, stable and inexpensive catalyst for this reaction. Herein, Ni-doped CeO2 nanoparticles were tested for CO2 methanation showing an extremely high Ni mass-specific activity and CH4 selectivity. Operando characterization reveals that this performance is tightly associated with ionic Νi and Ce3+ surface sites, while formation of metallic Ni does not seem to considerably promote the reaction. Theoretical calculations confirmed the stability of interstitial ionic Ni sites on ceria surfaces and highlighted the role of Ce-O frustrated Lewis pair (FLP), Ni-O classical Lewis pair (CLP) and Ni-Ce pair sites to the activation of H2 and CO2 molecules. To a large extent, the theoretical predictions were validated by in situ spectroscopy under H2 and CO2 : H2 gaseous environments.
Asunto(s)
Dióxido de Carbono , Níquel , Gases , Hidrogenación , IonesRESUMEN
Nickel/doped-ceria composites are promising electrocatalysts for solid-oxide fuel and electrolysis cells. Very often steam is present in the feedstock of the cells, frequently mixed with other gases, such as hydrogen or CO2 . An increase in the steam concentration in the feed mixture is considered accountable for the electrode oxidation and the deactivation of the device. However, direct experimental evidence of the steam interaction with nickel/doped-ceria composites, with adequate surface specificity, are lacking. Herein we explore in situ the surface state of nickel/gadolinium-doped ceria (NiGDC) under O2 , H2 , and H2 O environments by using near-ambient-pressure X-ray photoelectron and absorption spectroscopies. Changes in the surface oxidation state and composition of NiGDC in response to the ambient gas are observed. It is revealed that, in the mbar pressure regime and at intermediate temperature conditions (500-700 °C), steam acts as an oxidant for nickel but has a dual oxidant/reductant function for doped ceria.
RESUMEN
The formation of polydopamine composite membranes at the water/air interface using different chemical strategies is reported. The use of either small molecules (urea, pyrocatechol) or polymers paves the way to understand which kind of compounds can be used for the formation of PDA-composite free-standing membranes produced at the water/air interface. On the basis of these screening results, we have found that alginate grafted with catechol groups allows the formation of robust free-standing films with asymmetric composition, stimuli-responsiveness, and self-healing properties. The stickiness of these membranes depends on the relative humidity, and its adhesion behavior on PDMS was characterized using the JKR method. Thus, alginate-catechol polydopamine films appear as a new class of PDA composites, mechanically robust through covalent cross-linking and based on fully biocompatible constituting partners. These results open the door to potential applications in the biomedical field.
Asunto(s)
Alginatos/química , Catecoles/química , Indoles/química , Polímeros/química , Agua/química , Aire , Ácido Glucurónico/química , Ácidos Hexurónicos/química , Tamaño de la Partícula , Propiedades de SuperficieRESUMEN
The insertion of a graphene layer between cobalt and a substrate modifies the morphology and the oxidation/reduction properties of supported cobalt particles. Co forms a relatively flat structure on ZnO and SiO2 , whereas individual Co nanoparticles are formed after graphene coating of these substrates. The graphene layer moderates the formation of cobalt oxide in 5×10-7 â mbar O2 and promotes the reduction of oxidized Co in H2 at lower temperature. Angle-resolved XPS measurements indicate that this is mainly a consequence of the restricted interaction of cobalt with the oxide supports. After the low-pressure redox treatments, the graphene layer maintains a relatively high quality with a small number of defect sites.
RESUMEN
Nickel/yttria-stabilized zirconia (YSZ) composites are the most commonly used fuel electrodes for solid oxide cells. While microstructural changes of Ni/YSZ during operational conditions have been thoroughly investigated, there is limited knowledge regarding Ni/YSZ surface chemistry under working conditions. In this study, we examine the interaction between Ni/YSZ electrodes and water vapor under open circuit and polarization conditions, utilizing near ambient pressure soft and hard X-ray photoelectron spectroscopies. Miniature cells with conventional porous Ni/YSZ composite cermet cathodes were modified to facilitate the direct spectroscopic observation of the functional electrode's areas close to the interface with the YSZ electrolyte. The results highlight dynamic changes in the oxidation state and composition of Ni/YSZ under H2 and H2O atmospheres. We also quantify the accumulation of impurities on the electrode surface. Through adjustments in the pretreatment of the cell, the correlation between the nickel surface oxidation state and the cell's electrochemical performance during H2O electroreduction is established. It is unequivocally shown that nickel surface oxidation in H2O electrolysis favors NiO over Ni(OH)x, providing critical insights into the mechanism of Ni-phase redistribution within the electrode during long-term operation. Depth-dependent photoemission measurements, combined with theoretical quantitative simulations, reveal that NiO and Ni phases are uniformly mixed on the surface during H2O electrolysis. This differs from the conventional expectation of a NiO-shell/Ni-core configuration in gas phase oxidation. These findings provide crucial insights into the surface chemistry of Ni/YSZ electrodes under conditions relevant to H2O electrolysis, elucidating their impact on the electrochemical performance of the cell.
RESUMEN
The interaction between metal particles and the oxide support, the so-called metal-support interaction, plays a critical role in the performance of heterogenous catalysts. Probing the dynamic evolution of these interactions under reactive gas atmospheres is crucial to comprehending the structure-performance relationship and eventually designing new catalysts with enhanced properties. Cobalt supported on TiO2 (Co/TiO2) is an industrially relevant catalyst applied in Fischer-Tropsch synthesis. Although it is widely acknowledged that Co/TiO2 is restructured during the reaction process, little is known about the impact of the specific gas phase environment at the material's surface. The combination of soft and hard X-ray photoemission spectroscopies are used to investigate in situ Co particles supported on pure and NaBH4-modified TiO2 under H2, O2, and CO2:H2 gas atmospheres. The combination of soft and hard X-ray photoemission methods, which allows for simultaneous probing of the chemical composition of surface and subsurface layers, is one of the study's unique features. It is shown that under H2, cobalt particles are encapsulated below a stoichiometric TiO2 layer. This arrangement is preserved under CO2 hydrogenation conditions (i.e., CO2:H2), but changes rapidly upon exposure to O2. The pretreatment of the TiO2 support with NaBH4 affects the surface mobility and prevents TiO2 spillover onto Co particles.
RESUMEN
Frustrated Lewis pairs (FLPs), discovered in the last few decades for homogeneous catalysts and in the last few years also for heterogeneous catalysts, are stimulating the scientific community's interest for their potential in small-molecule activation. Nevertheless, how an FLP activates stable molecules such as CO2 is still undefined. Through a careful spectroscopic study, we here report the formation of FLPs over a highly defective CeO2 sample prepared by microwave-assisted synthesis. Carbon dioxide activation over FLP is shown to occur through a bidentate carbonate bridging the FLP and implying a Ce3+-to-CO2 charge transfer, thus enhancing its activation. Carbon dioxide reaction with methanol to form monomethylcarbonate is here employed to demonstrate active roles of FLP and, eventually, to propose a reaction mechanism clarifying the role of Ce3+ and oxygen vacancies.
RESUMEN
The controllable synthesis of rutile TiO2 single crystal particles with the preferential orientation of {111} facets still remains a scientific and technological challenge. Here, we developed a facile route for fabrication of rutile TiO2 nanorod crystals (RTiO2NRs) having high ratios of oxidative {111} to reductive {110} surfaces. RTiO2NRs were synthesized using a peroxo-titanium complex (PTC) approach, which was controlled by changing the Ti/H2O2 ratio. The thus obtained RTiO2NRs revealed a high tendency to agglomerate through orientation-dependent attachment along the {110} facets. This resulted in an increased {111}/{110} surface ratio and led to a markedly improved photocatalytic activity of RTiO2NR aggregates. The reported findings illustrate the rich potential of the herein proposed facile and energy-efficient synthesis of nanostructured rutile TiO2-based photocatalysts.
RESUMEN
Nickel-doped ceria nanoparticles (Ni0.1Ce0.9O2-x NPs) were fabricated from Schiff-base complexes and characterized by various microscopic and spectroscopic methods. Clear evidence is provided for incorporation of nickel ions in the ceria lattice in the form of Ni3+ species which is considered as the hole trapped state of Ni2+. The Ni0.1Ce0.9O2-x NPs exhibit enhanced reducibility in H2 as compared to conventional ceria-supported Ni particles, while in O2 the dopant nickel cations are oxidized at higher valence than the supported ones.
RESUMEN
Titanium (Ti) is the most widely used metal in biomedical applications because of its biocompatibility; however, the significant difference in the mechanical properties between Ti and the surrounding tissues results in stress shielding which is detrimental for load-bearing tissues. In the current study, to attenuate the stress shielding effect, a new processing route was developed. It aimed at growing thick poly(methyl methacrylate) (PMMA) layers grafted on Ti substrates to incorporate a polymer component on Ti implants. However, the currently available methods do not allow the development of thick polymeric layers, reducing significantly their potential uses. The proposed route consists of an alkali activation of Ti substrates followed by a surface-initiated atom transfer radical polymerization using a phosphonic acid derivative as a coupling agent and a polymerization initiator and malononitrile as a polymerization activator. The average thickness of the grown PMMA layers is approximately 1.9 µm. The Ti activation-performed in a NaOH solution-leads to a porous sodium titanate interlayer with a hierarchical structure and an open microporosity. It promotes the covalent grafting reaction because of high hydroxyl groups' content and enables establishing a further mechanical interlocking between the growing PMMA layer and the Ti substrate. As a result, the produced graduated structure possesses high Ti/PMMA adhesion strength (â¼260 MPa). Moreover, the PMMA layer is (i) thicker compared to those obtained with the previously reported techniques (â¼1.9 µm), (ii) stable in a simulated body fluid solution, and (iii) biocompatible. This strategy opens new opportunities toward hybrid prosthesis with adjustable mechanical properties with respect to host bone properties for personalized medicines.
RESUMEN
Progress in the development of proton exchange membrane (PEM) water electrolysis technology requires decreasing the anode overpotential, where the sluggish multistep oxygen evolution reaction (OER) occurs. This calls for an understanding of the nature of the active OER sites and reaction intermediates, which are still being debated. In this work, we apply synchrotron radiation-based near-ambient pressure X-ray photoelectron and absorption spectroscopies under operando conditions in order to unveil the nature of the reaction intermediates and shed light on the OER mechanism on electrocatalysts most widely used in PEM electrolyzers-electrochemical and thermal iridium oxides. Analysis of the O K-edge and Ir 4f spectra backed by density functional calculations reveals a universal oxygen anion red-ox mechanism regardless of the nature (electrochemical or thermal) of the iridium oxide. The formation of molecular oxygen is considered to occur through a chemical step from the electrophilic OI- species, which itself is formed in an electrochemical step.
RESUMEN
Cobalt particles dispersed on an oxide support form the basis of many important heterogeneous catalysts. Strong interactions between cobalt and the support may lead to irreducible cobalt oxide formation, which is detrimental for the catalytic performance. Therefore, several strategies have been proposed to enhance cobalt reducibility, such as alloying with Pt or utilization of nonoxide supports. In this work, we fabricate bimetallic PtCo supported on graphene-coated ZnO with enhanced cobalt reducibility. By employing a model/planar catalyst formulation, we show that the surface reduction of cobalt oxide is substantially enhanced by the presence of the graphene support as compared to bare ZnO. Stimulated by these findings, we synthesized a realistic powder catalyst consisting of PtCo particles grafted on graphene-coated ZnO support. We found that the addition of graphene coating enhances the surface reducibility of cobalt, fully supporting the results obtained on the model system. Our study demonstrates that realistic catalysts with designed properties can be developed on the basis of insights gained from model catalytic formulation.
RESUMEN
Understanding the surface chemistry of electrode materials under gas environments is important in order to control their performance during electrochemical and catalytic applications. This work compares the surface reactivity of Ni/YSZ and La0.75Sr0.25Cr0.9Fe0.1O3, which are commonly used types of electrodes in solid oxide electrochemical devices. In situ synchrotron-based near-ambient pressure photoemission and absorption spectroscopy experiments, assisted by theoretical spectral simulations and combined with microscopy and electrochemical measurements, are used to monitor the effect of the gas atmosphere on the chemical state, the morphology, and the electrical conductivity of the electrodes. It is shown that the surface of both electrode types readjusts fast to the reactive gas atmosphere and their surface composition is notably modified. In the case of Ni/YSZ, this is followed by evident changes in the oxidation state of nickel, while for La0.75Sr0.25Cr0.9Fe0.1O3, a fine adjustment of the Cr valence and strong Sr segregation is observed. An important difference between the two electrodes is their capacity to maintain adsorbed hydroxyl groups on their surface, which is expected to be critical for the electrocatalytic properties of the materials. The insight gained from the surface analysis may serve as a paradigm for understanding the effect of the gas environment on the electrochemical performance and the electrical conductivity of the electrodes.
RESUMEN
Proton exchange membrane (PEM) electrolyzers are attracting an increasing attention as a promising technology for the renewable electricity storage. In this work, near ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) is applied for in situ monitoring of the surface state of membrane electrode assemblies with RuO2 and bimetallic Ir0.7Ru0.3O2 anodes during water splitting. We demonstrate that Ir protects Ru from the formation of an unstable hydrous Ru(IV) oxide thereby rendering bimetallic Ru-Ir oxide electrodes with higher corrosion resistance. We further show that the water splitting occurs through a surface Ru(VIII) intermediate, and, contrary to common opinion, the presence of Ir does not hinder its formation.
RESUMEN
The development of efficient energy conversion systems requires precise engineering of electrochemical interfaces and thus asks for in situ techniques to probe the structure and the composition of the dynamic electrode/electrolyte interfacial region. This work demonstrates the potential of the near ambient pressure X-ray photoelectron spectroscopy (NAPXPS) for in situ studies of processes occurring at the interface between a metal electrode and a liquid electrolyte. By using a model membrane-electrode assembly of a high temperature phosphoric acid-imbibed proton exchange membrane fuel cell, and combining NAPXPS measurements with the density functional theory, it was possible to monitor such fundamental processes as dissociation and migration of the phosphoric acid within a nanostructured Pt electrode under polarization.
RESUMEN
Single-layer chemical vapor deposition (CVD)-grown graphene was transferred onto a ZnO (0001) substrate forming a large-area, low-defect density, protective layer. The quality of the graphene layer and its effect on the interaction between the ZnO support and vapor-deposited cobalt particles was investigated by spectroscopic and microscopic techniques. We demonstrate that the in-between graphene layer influences both the oxidation state and the morphology of cobalt upon annealing in vacuum. In particular, cobalt strongly interacts with the bare ZnO substrate forming flat particles, which are readily oxidized and redispersed upon annealing in ultrahigh vacuum conditions. In contrast, in the presence of the graphene interlayer, cobalt forms highly dispersed nanoparticles, which are resistant to oxidation, but prone to surface diffusion and agglomeration. The graphene layer exhibits remarkable stability upon cobalt deposition and vacuum annealing, while interaction with reactive gases can facilitate the formation of defects.
RESUMEN
The reduction and oxidation of carbon-supported cobalt nanoparticles (3.50±0.22 nm) and a Co (0001) single crystal was investigated by ambient pressure X-ray photoelectron (APPES) and X-ray absorption (XAS) spectroscopies, applied in situ under 0.2 mbar hydrogen or oxygen atmospheres and at temperatures up to 620 K. It was found that cobalt nanoparticles are readily oxidized to a distinct CoO phase, which is significantly more stable to further oxidation or reduction compared to the thick oxide films formed on the Co(0001) crystal. The nontrivial size-dependence of redox behavior is followed by a difference in the electronic structure as suggested by theoretical simulations of the Co L-edge absorption spectra. In particular, contrary to the stable rocksalt and spinel phases that exist in the bulk oxides, cobalt nanoparticles contain a significant portion of metastable wurtzite-type CoO.