Dynamic Nuclear Polarization Enables NMR of Surface Passivating Agents on Hybrid Perovskite Thin Films.

Surface and bulk molecular modulators are the key to improving the efficiency and stability of hybrid perovskite solar cells. However, due to their low concentration, heterogeneous environments, and low sample mass, it remains challenging to characterize their structure and dynamics at the atomic level, as required to establish structure-activity relationships. Nuclear magnetic resonance (NMR) spectroscopy has revealed a wealth of information on the atomic-level structure of hybrid perovskites, but the inherent insensitivity of NMR severely limits its utility to characterize thin-film samples. Dynamic nuclear polarization (DNP) can enhance NMR sensitivity by orders of magnitude, but DNP methods for perovskite materials have so far been limited. Here, we determined the factors that limit the efficiency of DNP NMR for perovskite samples by systematically studying layered hybrid perovskite analogues. We find that the fast-relaxing dynamic cation is the major impediment to higher DNP efficiency, while microwave absorption and particle morphology play a secondary role. We then show that the former can be mitigated by deuteration, enabling 1H DNP enhancement factors of up to 100, which can be harnessed to enhance signals from dopants or additives present in very low concentrations. Specifically, using this new DNP methodology at a high magnetic field and with small sample volumes, we have recorded the NMR spectrum of the 20 nm (6 µg) passivating layer on a single perovskite thin film, revealing a two-dimensional (2D) layered perovskite structure at the surface that resembles the n = 1 homologue but which has greater disorder than in bulk layered perovskites.

Phenanthrene-Fused-Quinoxaline as a Key Building Block for Highly Efficient and Stable Sensitizers in Copper-Electrolyte-Based Dye-Sensitized Solar Cells.

Dye-sensitized solar cells (DSSCs) based on CuII/I bipyridyl or phenanthroline complexes as redox shuttles have achieved very high open-circuit voltages (VOC , more than 1 V). However, their short-circuit photocurrent density (JSC ) has remained modest. Increasing the JSC is expected to extend the spectral response of sensitizers to the red or NIR region while maintaining efficient electron injection in the mesoscopic TiO2 film and fast regeneration by the CuI complex. Herein, we report two new D-A-π-A-featured sensitizers termed HY63 and HY64, which employ benzothiadiazole (BT) or phenanthrene-fused-quinoxaline (PFQ), respectively, as the auxiliary electron-withdrawing acceptor moiety. Despite their very similar energy levels and absorption onsets, HY64-based DSSCs outperform their HY63 counterparts, achieving a power conversion efficiency (PCE) of 12.5 %. PFQ is superior to BT in reducing charge recombination resulting in the near-quantitative collection of photogenerated charge carriers.

Low-Cost and Highly Efficient Carbon-Based Perovskite Solar Cells Exhibiting Excellent Long-Term Operational and UV Stability.

Today's perovskite solar cells (PSCs) mostly use components, such as organic hole conductors or noble metal back contacts, that are very expensive or cause degradation of their photovoltaic performance. For future large-scale deployment of PSCs, these components need to be replaced with cost-effective and robust ones that maintain high efficiency while ascertaining long-term operational stability. Here, a simple and low-cost PSC architecture employing dopant-free TiO2 and CuSCN as the electron and hole conductor, respectively, is introduced while a graphitic carbon layer deposited at room temperature serves as the back electrical contact. The resulting PSCs show efficiencies exceeding 18% under standard AM 1.5 solar illumination and retain ≈95% of their initial efficiencies for >2000 h at the maximum power point under full-sun illumination at 60 °C. In addition, the CuSCN/carbon-based PSCs exhibit remarkable stability under ultraviolet irradiance for >1000 h while under similar conditions, the standard spiro-MeOTAD/Au based devices degrade severely.

Influence of Alkoxy Chain Length on the Properties of Two-Dimensionally Expanded Azulene-Core-Based Hole-Transporting Materials for Efficient Perovskite Solar Cells.

A series of two-dimensionally expanded azulene-core-based π systems have been synthesized with different alkyl chain lengths in the alkoxy moieties connected to the partially oxygen-bridged triarylamine skeletons. The thermal, photophysical, and electronic properties of each compound were evaluated to determine the influence of the alkyl chain length on their effectiveness as hole-transporting materials (HTMs) in perovskite solar cells (PSCs). All the synthesized molecules showed promising material properties, including high solubility, the formation of flat and amorphous films, and optimal alignment of energy levels with perovskites. In particular, the derivatives with methyl and n-butyl in the side chains retained amorphous stability up to 233 and 159 °C, respectively. Such short alkoxy chains also resulted in improved electrical device properties. The PSC device fabricated with the HTM with n-butyl side chains showed the best performance with a power conversion efficiency of 18.9 %, which compares favorably with that of spiro-OMeTAD-based PSCs (spiro-OMeTAD=2,2',7,7'-tetrakis[N,N-bis(p-methoxyphenyl)amino]-9,9'-spirobifluorene).

Sequential catalysis enables enhanced C-C coupling towards multi-carbon alkenes and alcohols in carbon dioxide reduction: a study on bifunctional Cu/Au electrocatalysts.

Electrochemical reduction of carbon dioxide (CO2) to multi-carbon products such as ethylene, ethanol and n-propanol offers a promising path for utilization of excessive CO2 and energy storage. Oxide-derived Cu electrodes are among the best electrocatalysts for the selective formation of ethylene and ethanol. However, a large fraction of the faradaic current still goes to hydrogen evolution, even at optimal conditions (electrolyte, potential, etc.). Here we employ the concept of sequential catalysis using judiciously designed CuAu bimetallic catalysts through galvanic exchange between Au3+ and Cu2O nanowires. By controlling the concentration of the Au3+ precursor and the exchange time, Au nanoparticles were evenly dispersed onto the Cu2O nanowires. The optimized oxide-derived CuAu catalyst showed remarkable improvement towards the formation of ethylene, ethanol and n-propanol, in terms of faradaic efficiency and current density. Our analysis of the electrochemical formation of carbon monoxide, ethylene and hydrogen suggests that the presence of Au, an electrocatalyst for CO2-to-CO conversion, helps enhance *CO-coverage on Cu, thus promoting the production of multi-carbon products and suppressing hydrogen formation on the CuAu catalyst. We propose promising strategies for designing electrochemical systems, which would enable the selective and scalable reduction of CO2 to ethylene and ethanol.

Mesoscopic Oxide Double Layer as Electron Specific Contact for Highly Efficient and UV Stable Perovskite Photovoltaics.

The solar to electric power conversion efficiency (PCE) of perovskite solar cells (PSCs) has recently reached 22.7%, exceeding that of competing thin film photovoltaics and the market leader polycrystalline silicon. Further augmentation of the PCE toward the Shockley-Queisser limit of 33.5% warrants suppression of radiationless carrier recombination by judicious engineering of the interface between the light harvesting perovskite and the charge carrier extraction layers. Here, we introduce a mesoscopic oxide double layer as electron selective contact consisting of a scaffold of TiO2 nanoparticles covered by a thin film of SnO2, either in amorphous (a-SnO2), crystalline (c-SnO2), or nanocrystalline (quantum dot) form (SnO2-NC). We find that the band gap of a-SnO2 is larger than that of the crystalline (tetragonal) polymorph leading to a corresponding lift in its conduction band edge energy which aligns it perfectly with the conduction band edge of both the triple cation perovskite and the TiO2 scaffold. This enables very fast electron extraction from the light perovskite, suppressing the notorious hysteresis in the current-voltage ( J-V) curves and retarding nonradiative charge carrier recombination. As a result, we gain a remarkable 170 mV in open circuit photovoltage ( V oc) by replacing the crystalline SnO2 by an amorphous phase. Because of the quantum size effect, the band gap of our SnO2-NC particles is larger than that of bulk SnO2 causing their conduction band edge to shift also to a higher energy thereby increasing the V oc. However, for SnO2-NC there remains a barrier for electron injection into the TiO2 scaffold decreasing the fill factor of the device and lowering the PCE. Introducing the a-SnO2 coated mp-TiO2 scaffold as electron extraction layer not only increases the V oc and PEC of the solar cells but also render them resistant to UV light which forebodes well for outdoor deployment of these new PSC architectures.

Electron-Affinity-Triggered Variations on the Optical and Electrical Properties of Dye Molecules Enabling Highly Efficient Dye-Sensitized Solar Cells.

The synthesis, characterization, and photovoltaic performance of a series of indacenodithiophene (IDT)-based D-π-A organic dyes with varying electron-accepting units is presented. By control of the electron affinity, perfectly matching energy levels were achieved with a copper(I/II)-based redox electrolyte, reaching a high open-circuit voltage (>1.1 V) while harvesting a large fraction of solar photons at the same time. Besides achieving high power conversion efficiencies (PCEs) for dye-sensitized solar cells (DSCs), that is, 11.2 % under standard AM 1.5 G sunlight, and 28.4 % under a 1000 lux fluorescent light tube, this work provides a possible method for the design and fabrication of low-cost highly efficient DSCs.

Intrinsic and Extrinsic Stability of Formamidinium Lead Bromide Perovskite Solar Cells Yielding High Photovoltage.

We report on both the intrinsic and the extrinsic stability of a formamidinium lead bromide [CH(NH2)2PbBr3 = FAPbBr3] perovskite solar cell that yields a high photovoltage. The fabrication of FAPbBr3 devices, displaying an outstanding photovoltage of 1.53 V and a power conversion efficiency of over 8%, was realized by modifying the mesoporous TiO2-FAPbBr3 interface using lithium treatment. Reasons for improved photovoltaic performance were revealed by a combination of techniques, including photothermal deflection absorption spectroscopy (PDS), transient-photovoltage and charge-extraction analysis, and time-integrated and time-resolved photoluminescence. With lithium-treated TiO2 films, PDS reveals that the TiO2-FAPbBr3 interface exhibits low energetic disorder, and the emission dynamics showed that electron injection from the conduction band of FAPbBr3 into that of mesoporous TiO2 is faster than for the untreated scaffold. Moreover, compared to the device with pristine TiO2, the charge carrier recombination rate within a device based on lithium-treated TiO2 film is 1 order of magnitude lower. Importantly, the operational stability of perovskites solar cells examined at a maximum power point revealed that the FAPbBr3 material is intrinsically (under nitrogen) as well as extrinsically (in ambient conditions) stable, as the unsealed devices retained over 95% of the initial efficiency under continuous full sun illumination for 150 h in nitrogen and dry air and 80% in 60% relative humidity (T = ∼60 °C). The demonstration of high photovoltage, a record for FAPbBr3, together with robust stability renders our work of practical significance.

Nanowire perovskite solar cell.

Organolead iodide perovskite, CH3NH3PbI3, was prepared in the form of nanowire by means of a small quantity of aprotic solvent in two-step spin-coating procedure. One-dimensional nanowire perovskite with the mean diameter of 100 nm showed faster carrier separation in the presence of hole transporting layer and higher lateral conductivity than the three-dimensional nanocuboid crystal. Reduction in dimensionality resulted in the hypsochromic shift of both absorption and fluorescence spectra, indicative of more localized exciton states in nanowires. The best performing device employing nanowire CH3NH3PbI3 delivered photocurrent density of 19.12 mA/cm(2), voltage of 1.052 V, and fill factor of 0.721, leading to a power conversion efficiency (PCE) of 14.71% at standard AM 1.5G solar illumination. A small I-V hysteresis was observed, where a PCE at forward scan was measured to be 85% of the PCE at reverse scan.

Boosting Interfacial Electron Transfer and CO2 Enrichment on ZIF-8/ZnTe for Selective Photoelectrochemical Reduction of CO2 to CO.

Artificial photosynthesis is an effective way of converting CO2 into fuel and high value-added chemicals. However, the sluggish interfacial electron transfer and adsorption of CO2 at the catalyst surface strongly hamper the activity and selectivity of CO2 reduction. Here, we report a photocathode attaching zeolitic imidazolate framework-8 (ZIF-8) onto a ZnTe surface to mimic an aquatic leaf featuring stoma and chlorophyll for efficient photoelectrochemical conversion of CO2 into CO. ZIF-8 possessing high CO2 adsorption capacity and diffusivity has been selected to enrich CO2 into nanocages and provide a large number of catalytic active sites. ZnTe with high light-absorption capacity serves as a light-absorbing layer. CO2 molecules are collected in large nanocages of ZIF-8 and delivered to the ZnTe surface. As evidenced by scanning electrochemical microscopy, the interface can effectively boost interfacial electron transfer kinetics. The ZIF-8/ZnTe photocathode with unsaturated Zn-Nx sites exhibits a high Faradaic efficiency for CO production of 92.9% and a large photocurrent of 6.67 mA·cm-2 at -2.48 V (vs Fc/Fc+) in a nonaqueous electrolyte at AM 1.5G solar irradiation (100 mW·cm-2).

Measured binding coefficients for iodine and ruthenium dyes; implications for recombination in dye sensitised solar cells.

We have measured the binding coefficients of iodine to three dyes used in Dye Sensitised Solar Cells (DSSCs). Binding coefficients are quantified via the effect of iodine binding on the UV-vis spectrum of the dye. From iodine titration curves of dye sensitised TiO(2) films we find that the binding coefficients of iodine to the dyes C101, N719 and AR24 (vide infra) are in the range of 2000-4000 M(-1). From FTIR results and molecular modelling we show the iodine binds to the thiocyanate group in all these dyes. For the AR24 dye we present evidence that iodine also binds to the amine moiety on this dye. With these binding coefficients we show that the dye-iodine complex will be present at much higher concentrations than free iodine in the pore structure of a DSSC. As we have recently shown that iodine (rather than tri-iodide) is the dominant acceptor in electron recombination, the concentration dye-iodine complexes could influence recombination rates and thus V(oc). By comparison of recombination data on full cells, we show that AR24 accelerates recombination by a factor of 7 over N719, presumably due to the iodine binding to the amine group. We leave open the question why iodine binding to the amine group seems to have a stronger effect on the recombination than does binding to the thiocyanate.

Solar reduction of carbon dioxide on copper-tin electrocatalysts with energy conversion efficiency near 20.

Copper catalysts modified with tin have been demonstrated to be selective for the electroreduction of carbon dioxide to carbon monoxide. However, such catalysts require the precise control of tin loading amount. Here, we develop a copper/tin-oxide catalyst with dominant tin oxide surface being formed via a spontaneous exchange reaction between sputtered tin and copper oxide. Even though the surface of this catalyst is tin-rich, it achieves an excellent performance towards carbon monoxide production in a flow cell. This contrasts with copper/tin-oxide prepared via atomic layer deposition since it yields selectivity towards carbon monoxide only on a copper-rich surface. Mechanism studies reveal that the tin sites on the tin-rich copper/tin-oxide surface achieve a suitable binding with adsorbed carbon monoxide under the presence of copper. Powered by a triple-junction solar cell, the copper/tin-oxide based electrolyzer sets a new benchmark solar-to-chemical energy conversion efficiency of 19.9 percent with a Faradaic efficiency of 98.9 percent towards carbon monoxide under simulated standard air mass 1.5 global illumination.

Enabling full-scale grain boundary mitigation in polycrystalline perovskite solids.

There exists a considerable density of interaggregate grain boundaries (GBs) and intra-aggregate GBs in polycrystalline perovskites. Mitigation of intra-aggregate GBs is equally notable to that of interaggregate GBs as intra-aggregate GBs can also cause detrimental effects on the photovoltaic performances of perovskite solar cells (PSCs). Here, we demonstrate full-scale GB mitigation ranging from nanoscale intra-aggregate to submicron-scale interaggregate GBs, by modulating the crystallization kinetics using a judiciously designed brominated arylamine trimer. The optimized GB-mitigated perovskite films exhibit reduced nonradiative recombination, and their corresponding mesostructured PSCs show substantially enhanced device efficiency and long-term stability under illumination, humidity, or heat stress. The versatility of our strategy is also verified upon applying it to different categories of PSCs. Our discovery not only specifies a rarely addressed perspective concerning fundamental studies of perovskites at nanoscale but also opens a route to obtain high-quality solution-processed polycrystalline perovskites for high-performance optoelectronic devices.

Effect of sensitizer adsorption temperature on the performance of dye-sensitized solar cells.

Employing a mesoscopic titania photoanode whose bilayer structure was judiciously selected to fit the optoelectronic characteristics of the Ru-based heteroleptic complex Na-cis-Ru(4,4'-(5-hexyltiophen-2-yl)-2,2'-bipyridine)(4-carboxylic-acid-4'-carboxylate-2,2'-bipyridine)(thiocyanate)(2), coded as C101, we investigated the effect of temperature for dye adsorption on the photovoltaic performance of dye-sensitized solar cells (DSCs). We found a significant efficiency enhancement upon lowering the temperature applied during the sensitizer uptake from solution. When the dye adsorption was performed at 4 °C, the photovoltaic performance parameters measured under standard reporting conditions (AM1.5 G sunlight at 1000 W/m(2) intensity and 25 °C), i.e., the open circuit voltage (V(oc)), the short circuit photocurrent density (J(sc)), the fill factor (FF), and consequently the power conversion efficiency (PCE), improved in comparison to cells stained at 20 and 60 °C. Results from electrochemical impedance spectroscopy (EIS) and attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) show that the self-assembled layer of C101 formed at lower temperature impairs the back-electron transfer from the TiO(2) conduction band to the triiodide ions in the electrolyte more strongly than the film produced at 60 °C. Profiting from the favorable influence that the low-temperature dye uptake exerts on photovoltaic performance, we have realized DSCs showing a power conversion efficiency of 11.5%.

Application of ionic liquids containing tricyanomethanide [C(CN)3]- or tetracyanoborate [B(CN)4]- anions in dye-sensitized solar cells.

A series of novel ionic liquids composed of imidazolium, pyridinium, pyrrolidinium, and ammonium cations with tricyanomethanide or tetracyanoborate anions were prepared. The ionic liquids were characterized by NMR and IR spectroscopy and ESI-mass spectrometry, and their physical properties were investigated. Solid state structures of the N-propyl-N-methylpyrrolidinium and triethylpropylammonium tetracyanoborate salts were obtained by single crystal X-ray diffraction. The salts that are liquid at room temperature were evaluated as electrolyte additives in dye-sensitized solar cells, giving rise to efficiencies 7.35 and 7.85% under 100 and 10% Sun, respectively, in combination with the standard Z907 dye.

A combined molecular dynamics and experimental study of two-step process enabling low-temperature formation of phase-pure α-FAPbI3.

It is well established that the lack of understanding the crystallization process in a two-step sequential deposition has a direct impact on efficiency, stability, and reproducibility of perovskite solar cells. Here, we try to understand the solid-solid phase transition occurring during the two-step sequential deposition of methylammonium lead iodide and formamidinium lead iodide. Using metadynamics, x-ray diffraction, and Raman spectroscopy, we reveal the microscopic details of this process. We find that the formation of perovskite proceeds through intermediate structures and report polymorphs found for methylammonium lead iodide and formamidinium lead iodide. From simulations, we discover a possible crystallization pathway for the highly efficient metastable α phase of formamidinium lead iodide. Guided by these simulations, we perform experiments that result in the low-temperature crystallization of phase-pure α-formamidinium lead iodide.

Efficient and stable inverted perovskite solar cells with very high fill factors via incorporation of star-shaped polymer.

Stabilizing high-efficiency perovskite solar cells (PSCs) at operating conditions remains an unresolved issue hampering its large-scale commercial deployment. Here, we report a star-shaped polymer to improve charge transport and inhibit ion migration at the perovskite interface. The incorporation of multiple chemical anchor sites in the star-shaped polymer branches strongly controls the crystallization of perovskite film with lower trap density and higher carrier mobility and thus inhibits the nonradiative recombination and reduces the charge-transport loss. Consequently, the modified inverted PSCs show an optimal power conversion efficiency of 22.1% and a very high fill factor (FF) of 0.862, corresponding to 95.4% of the Shockley-Queisser limited FF (0.904) of PSCs with a 1.59-eV bandgap. The modified devices exhibit excellent long-term operational and thermal stability at the maximum power point for 1000 hours at 45°C under continuous one-sun illumination without any significant loss of efficiency.

A Blue Photosensitizer Realizing Efficient and Stable Green Solar Cells via Color Tuning by the Electrolyte.

Semitransparent dye-sensitized solar cells (DSCs) are appealing as aesthetically pleasing and colorful see-through photovoltaics. Green semitransparent DSCs have been presented, but the best ones rely on green zinc porphyrin photosensitizers and high volatile electrolytes. For potential outdoor applications, the zinc porphyrin DSCs employing ionic liquid electrolytes merely reached a power conversion efficiency (PCE) of 6.3% even with opaque mesoporous TiO2 films. Herein, the new green DSC is realized by using a blue organic photosensitizer in conjunction with an orange ionic-liquid-based electrolyte, presenting a simple and an effective path for color tuning of photovoltaics. The new approach allows for broadly modulating the color from spring green to cyan by tuning the contributions of the light absorption by the dye-sensitized TiO2 film and the electrolyte layer. The new semitransparent DSCs with spring green to cyan colors have PCEs ranging from 6.7% to 8.1% and show stability for 1000 h under accelerated ageing test at 80 °C, superior to the zinc porphyrin DSCs. The findings pave a new way to achieve efficient and stable colorful solar cells.

Large-Grain Tin-Rich Perovskite Films for Efficient Solar Cells via Metal Alloying Technique.

Fast research progress on lead halide perovskite solar cells has been achieved in the past a few years. However, the presence of lead (Pb) in perovskite composition as a toxic element still remains a major issue for large-scale deployment. In this work, a novel and facile technique is presented to fabricate tin (Sn)-rich perovskite film using metal precursors and an alloying technique. Herein, the perovskite films are formed as a result of the reaction between Sn/Pb binary alloy metal precursors and methylammonium iodide (MAI) vapor in a chemical vapor deposition process carried out at 185 °C. It is found that in this approach the Pb/Sn precursors are first converted to (Pb/Sn)I2 and further reaction with MAI vapor leads to the formation of perovskite films. By using Pb-Sn eutectic alloy, perovskite films with large grain sizes up to 5 µm can be grown directly from liquid phase metal. Consequently, using an alloying technique and this unique growth mechanism, a less-toxic and efficient perovskite solar cell with a power conversion efficiency (PCE) of 14.04% is demonstrated, while pure Sn and Pb perovskite solar cells prepared in this manner yield PCEs of 4.62% and 14.21%, respectively. It is found that this alloying technique can open up a new direction to further explore different alloy systems (binary or ternary alloys) with even lower melting point.

The Role of Rubidium in Multiple-Cation-Based High-Efficiency Perovskite Solar Cells.

Perovskite solar cells (PSCs) based on cesium (Cs)- and rubidium (Rb)-containing perovskite films show highly reproducible performance; however, a fundamental understanding of these systems is still emerging. Herein, this study has systematically investigated the role of Cs and Rb cations in complete devices by examining the transport and recombination processes using current-voltage characteristics and impedance spectroscopy in the dark. As the credibility of these measurements depends on the performance of devices, this study has chosen two different PSCs, (MAFACs)Pb(IBr)3 (MA = CH3 NH3+ , FA = CH(NH2 )2+ ) and (MAFACsRb)Pb(IBr)3 , yielding impressive performances of 19.5% and 21.1%, respectively. From detailed studies, this study surmises that the confluence of the low trap-assisted charge-carrier recombination, low resistance offered to holes at the perovskite/2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9-spirobifluorene interface with a low series resistance (Rs ), and low capacitance leads to the realization of higher performance when an extra Rb cation is incorporated into the absorber films. This study provides a thorough understanding of the impact of inorganic cations on the properties and performance of highly efficient devices, and also highlights new strategies to fabricate efficient multiple-cation-based PSCs.