Identification and map-based cloning of an EMS-induced mutation in wheat gene TaSP1 related to spike architecture.

KEY MESSAGE: A candidate gene TaSP1 related to spike shape was cloned, and the gene-specific marker was developed to efficiently track the superior haplotype in common wheat. Spike shape, an important factor that affects wheat grain yield, is mainly defined by spike length (SPL), spikelet number (SPN), and compactness. Zhoumai32 mutant 1160 (ZM1160), a mutant obtained from ethyl methane sulfonate (EMS) treatment of hexaploid wheat variety Zhoumai32, was used to identify and clone the candidate gene that conditioned the spike shape. Genetic analysis of an F2 population derived from a cross of ZM1160 and Bainong207 suggested that the compact spike shape in ZM1160 was controlled by a single recessive gene, and therefore, the mutated gene was designated as Tasp1. With polymorphic markers identified through bulked segregant analysis (BSA), the gene was mapped to a 2.65-cM interval flanked by markers YZU0852 and MIS46239 on chromosome 7D, corresponding to a 0.42-Mb physical interval of Chinese spring (CS) reference sequences (RefSeq v1.0). To fine map TaSP1, 15 and seven recombinants were, respectively, screened from 1599 and 1903 F3 plants derived from the heterozygous F2 plants. Finally, TaSP1 was delimited to a 21.9 Kb (4,870,562 to 4,892,493 bp) Xmis48123-Xmis48104 interval. Only one high-confidence gene TraesCS7D02G010200 was annotated in this region, which encodes an unknown protein with a putative vWA domain. Quantitative reverse transcription PCR (qRT-PCR) analysis showed that TraesCS7D02G010200 was mainly expressed in the spike. Haplotype analysis of 655 wheat cultivars using the candidate gene-specific marker Xg010200p2 identified a superior haplotype TaSP1b with longer spike and more spikelet number. TaSP1 is beneficial to the improvement in wheat spike shape.

NFMPAtt-Unet: Neighborhood Fuzzy C-means Multi-scale Pyramid Hybrid Attention Unet for medical image segmentation.

Medical image segmentation is crucial for understanding anatomical or pathological changes, playing a key role in computer-aided diagnosis and advancing intelligent healthcare. Currently, important issues in medical image segmentation need to be addressed, particularly the problem of segmenting blurry edge regions and the generalizability of segmentation models. Therefore, this study focuses on different medical image segmentation tasks and the issue of blurriness. By addressing these tasks, the study significantly improves diagnostic efficiency and accuracy, contributing to the overall enhancement of healthcare outcomes. To optimize segmentation performance and leverage feature information, we propose a Neighborhood Fuzzy c-Means Multiscale Pyramid Hybrid Attention Unet (NFMPAtt-Unet) model. NFMPAtt-Unet comprises three core components: the Multiscale Dynamic Weight Feature Pyramid module (MDWFP), the Hybrid Weighted Attention mechanism (HWA), and the Neighborhood Rough Set-based Fuzzy c-Means Feature Extraction module (NFCMFE). The MDWFP dynamically adjusts weights across multiple scales, improving feature information capture. The HWA enhances the network's ability to capture and utilize crucial features, while the NFCMFE, grounded in neighborhood rough set concepts, aids in fuzzy C-means feature extraction, addressing complex structures and uncertainties in medical images, thereby enhancing adaptability. Experimental results demonstrate that NFMPAtt-Unet outperforms state-of-the-art models, highlighting its efficacy in medical image segmentation.

Study on numerical simulation and mechanical properties of anchor cable with C-shaped tube subjected to shearing.

To examine the disparity in deformation behavior and mechanical qualities between anchor cables with C-shaped tubes and regular anchor cables under shear conditions. The double-sided shear tests of free-section anchor cables and anchor cables with C-shaped tubes were conducted utilizing the indoor large-scale double-shear test equipment with varying pretension loads. The indoor double-shear tests indicate that the inclusion of the C-shaped tube alters the stress distribution of the anchor cables inside the anchor cables with C-shaped tubes and mitigates the impact of stress concentration. Moreover, it facilitates the transition of the anchor cable's failure mode from a mix of tensile and shear breaking to mainly tensile breakage. In addition, ABAQUS finite element analysis software was used to establish a double shear test model of the anchor cable with C-shaped tube to accurately simulate the interaction and stress distribution among the anchor cable, C-shaped tube, and concrete block in the double shear test. The findings of the simulation results reveal that the numerical model can adequately depict the evolution of the stress distribution in the prestressed anchored structure and the damage of the concrete block with increasing shear displacement. The relational equation for the yield state of the anchor cable with C-shaped tube under combined tensile and shear loads is found by integrating the experimental and simulation data, the static beam theory, and the concept of minimal potential energy.

Powering the Future Green Buildings: Multifunctional Ultraviolet-Shielding Transparent Wood.

Indoor UV damage is a serious problem that is often ignored. Common glasses cannot filter UV rays well and have fragility and environmental issues. UV-shielding transparent wood (TW) holds promise, yet striking the right balance between blocking UV rays and allowing sufficient visible-light transmission poses a challenge. The pronounced capillary force, fueled by persistent moisture and extractives in wood, alongside the existence of multiphase interfaces, collectively hinder the uniform penetration of polymers and the effective dispersion of nanomaterials within the wood skeleton. Here, we incorporate high-pressure supercritical CO2 fluid-assisted impregnation (HSCFI) into fabricating UV-shielding TW. The supercritical CO2 pretreatment efficiently eliminates moisture and refines wood structure by extracting polar substances, resulting in a prominent 52.4% increase in average water permeability. Subsequently, this HSCFI method facilitates the infiltration of methyl methacrylate (MMA) monomer and Ce-ZnO nanorods (NRDs) into the refined anhydrous wood, leveraging the excellent solvency of supercritical CO2 for MMA. The impregnation rate of PMMA undergoes a substantial increase from 34.5 to 59.1%. With the robust UV-blocking capability of Ce-ZnO NRDs, thanks to dual-valence Ce doping widening the ZnO energy gap via the Burstein-Moss effect and their unique photoactive microstructure featuring a solid prism with a sharp hexahedral pyramidal tip, along with intrinsic physical scattering/reflection actions, Ce-ZnO NRDs@TW achieves an impressive 99.6% UVA radiation blockage (the highest for TW) and maintains high visible-light transmission (83.2%). Furthermore, Ce-ZnO NRDs@TW presents favorable energy-saving, sound absorption, and antifungal abilities, making it a promising candidate for future green buildings.

Flash heating process for efficient meat preservation.

Maintaining food safety and quality is critical for public health and food security. Conventional food preservation methods, such as pasteurization and dehydration, often change the overall organoleptic quality of the food products. Herein, we demonstrate a method that affects only a thin surface layer of the food, using beef as a model. In this method, Joule heating is generated by applying high electric power to a carbon substrate in <1 s, which causes a transient increase of the substrate temperature to > ~2000 K. The beef surface in direct contact with the heating substrate is subjected to ultra-high temperature flash heating, leading to the formation of a microbe-inactivated, dehydrated layer of ~100 µm in thickness. Aerobic mesophilic bacteria, Enterobacteriaceae, yeast and mold on the treated samples are inactivated to a level below the detection limit and remained low during room temperature storage of 5 days. Meanwhile, the product quality, including visual appearance, texture, and nutrient level of the beef, remains mostly unchanged. In contrast, microorganisms grow rapidly on the untreated control samples, along with a rapid deterioration of the meat quality. This method might serve as a promising preservation technology for securing food safety and quality.