RESUMEN
Lithium-sulfur (Li-S) batteries with high energy density and low cost are promising for next-generation energy storage. However, their cycling stability is plagued by the high solubility of lithium polysulfide (LiPS) intermediates, causing fast capacity decay and severe self-discharge. Exploring electrolytes with low LiPS solubility has shown promising results toward addressing these challenges. However, here, we report that electrolytes with moderate LiPS solubility are more effective for simultaneously limiting the shuttling effect and achieving good Li-S reaction kinetics. We explored a range of solubility from 37 to 1,100 mM (based on S atom, [S]) and found that a moderate solubility from 50 to 200 mM [S] performed the best. Using a series of electrolyte solvents with various degrees of fluorination, we formulated the Single-Solvent, Single-Salt, Standard Salt concentration with Moderate LiPSs solubility Electrolytes (termed S6MILE) for Li-S batteries. Among the designed electrolytes, Li-S cells using fluorinated-1,2-diethoxyethane S6MILE (F4DEE-S6MILE) showed the highest capacity of 1,160 mAh g-1 at 0.05 C at room temperature. At 60 °C, fluorinated-1,4-dimethoxybutane S6MILE (F4DMB-S6MILE) gave the highest capacity of 1,526 mAh g-1 at 0.05 C and an average CE of 99.89% for 150 cycles at 0.2 C under lean electrolyte conditions. This is a fivefold increase in cycle life compared with other conventional ether-based electrolytes. Moreover, we observed a long calendar aging life, with a capacity increase/recovery of 4.3% after resting for 30 d using F4DMB-S6MILE. Furthermore, the correlation between LiPS solubility, degree of fluorination of the electrolyte solvent, and battery performance was systematically investigated.
RESUMEN
Steelmaking contributes 8% to the total CO2 emissions globally, primarily due to coal-based iron ore reduction. Clean hydrogen-based ironmaking has variable performance because the dominant gas-solid reduction mechanism is set by the defects and pores inside the mm- to nm-sized oxide particles that change significantly as the reaction progresses. While these governing dynamics are essential to establish continuous flow of iron and its ores through reactors, the direct link between agglomeration and chemistry is still contested due to missing measurements. In this work, we directly measure the connection between chemistry and agglomeration in the smallest iron oxides relevant to magnetite ores. Using synthesized spherical 10-nm magnetite particles reacting in H2, we resolve the formation and consumption of wüstite (Fe1-xO)-the step most commonly attributed to whiskering. Using X-ray diffraction, we resolve crystallographic anisotropy in the rate of the initial reaction. Complementary imaging demonstrated how the particles self-assemble, subsequently react, and grow into elongated "whisker" structures. Our insights into how morphologically uniform iron oxide particles react and agglomerate in H2 reduction enable future size-dependent models to effectively describe the multiscale aspects of iron ore reduction.
RESUMEN
Lithium (Li) metal stands as a promising anode in advancing high-energy-density batteries. However, intrinsic issues associated with metallic Li, especially the dendritic growth, have hindered its practical application. Herein, we focus on molecular combined structural design to develop dendrite-free anodes. Specifically, using hydrogen-substituted graphdiyne (HGDY) aerogel hosts, we successfully fabricated a promising Li composite anode (Li@HGDY). The HGDY aerogel's lithiophilic nature and hierarchical pores drive molten Li infusion and reduce local current density within the three-dimensional HGDY host. The unique molecular structure of HGDY provides favorable bulk pathways for lithium-ion transport. By simultaneous regulation of electron and ion transport within the HGDY host, uniform lithium stripping/platting is fulfilled. Li@HGDY symmetric cells exhibit a low overpotential and stable cycling. The Li@HGDY||lithium iron phosphate full cell retained 98.1% capacity after 170 cycles at 0.4 C. This study sheds new light on designing high-capacity and long-lasting lithium metal anodes.
RESUMEN
Herein, the synthesis of branched α,ß-unsaturated amides by a hydroaminocarbonylation reaction of alkynes with various amine substrates such as aromatic amines, aliphatic amines, solid amine sources like NH4HCO3, and even strongly basic piperidines is reported, using a Pd(OAc)2/hybrid N-heterocyclic carbene-phosphine-phosphine (CPP) catalytic system. The reactions feature no additives, wide substrate scope, high selectivity (b/l > 99 : 1) and excellent yields. Mechanistic studies have disclosed that the reaction takes place via a palladium hydride pathway. CPP adopts a hybrid bidentate ligand conformation with a carbene-phosphine coordination mode, wherein one phosphorus atom remains externally accessible, potentially serving as a stabilizing auxiliary during catalytic cycles.
RESUMEN
Herein, a robust catalyst system, composed of a bipyridine-based diphosphine ligand (BiPyPhos) and a cobalt precursor Co(acac)2, is successfully developed and applied in the hydroboration of terminal alkynes, exclusively affording various versatile ß-E-vinylboronates in high yields at room temperature.
RESUMEN
The efficiency of the synthesis of renewable fuels and feedstocks from electrical sources is limited, at present, by the sluggish water oxidation reaction. Single-atom catalysts (SACs) with a controllable coordination environment and exceptional atom utilization efficiency open new paradigms toward designing high-performance water oxidation catalysts. Here, using operando X-ray absorption spectroscopy measurements with calculations of spectra and electrochemical activity, we demonstrate that the origin of water oxidation activity of IrNiFe SACs is the presence of highly oxidized Ir single atom (Ir5.3+) in the NiFe oxyhydroxide under operating conditions. We show that the optimal water oxidation catalyst could be achieved by systematically increasing the oxidation state and modulating the coordination environment of the Ir active sites anchored atop the NiFe oxyhydroxide layers. Based on the proposed mechanism, we have successfully anchored Ir single-atom sites on NiFe oxyhydroxides (Ir0.1/Ni9Fe SAC) via a unique in situ cryogenic-photochemical reduction method that delivers an overpotential of 183 mV at 10 mA â cm-2 and retains its performance following 100 h of operation in 1 M KOH electrolyte, outperforming the reported catalysts and the commercial IrO2 catalysts. These findings open the avenue toward an atomic-level understanding of the oxygen evolution of catalytic centers under in operando conditions.
RESUMEN
Lithium-sulfur (Li-S) batteries are promising candidates for next-generation energy storage systems due to their high theoretical energy density and the low cost of sulfur. However, slow conversion kinetics between the insulating S and lithium sulfide (Li2S) remains as a technical challenge. In this work, we report a catalyst featuring nickel (Ni) single atoms and clusters anchored to a porous hydrogen-substituted graphdiyne support (termed Ni@HGDY), which is incorporated in Li2S cathodes. The rapidly synthesized catalyst was found to enhance ionic and electronic conductivity, decrease the reaction overpotential, and promote more complete conversion between Li2S and sulfur. The addition of Ni@HGDY to commercial Li2S powder enabled a capacity of over 516 mAh gLi2S-1 at 1 C for over 125 cycles, whereas the control Li2S cathode managed to maintain just over 200 mAh gLi2S-1. These findings highlight the efficacy of Ni as a metal catalyst and demonstrate the promise of HGDY in energy storage devices.
RESUMEN
A facile route for direct access to the 4-iodopyrrole-2-carbaldehydes from pyridinium salts has been successfully developed, which undergoes cascade pyrrole-2-carbaldehydes construction/selective C4 position iodination process. Using Na2S2O8 as an oxidant and readily available sodium iodide as an iodine source, a variety of 4-iodopyrrole-2-carbaldehydes were obtained in good to excellent yields. Atom- and step-economy, good functional group tolerance, high regioselectivity, as well as mild conditions entail this transformation an alternative strategy for enriching pyrroles library.
RESUMEN
Phenotypic plasticity has been identified as a major mechanism of response to changing temperatures. Parental effects are potentially important drivers of ecological and evolutionary dynamics, while developmental plasticity also plays a key role in generating phenotypic variation. However, little is known of the interaction between parental effects and developmental plasticity on the thermal phenotypes of fishes with different reproductive modes (i.e. oviparous vs. viviparous). To understand the contributions of inter- and intra-generational plasticity of thermal phenotypes (preferred temperature, avoidance temperatures, critical thermal thresholds) in fishes with different reproductive modes, we carried out a factorial experiment in which both breeding parents and offspring were exposed to lower (22 °C) or higher (28 °C) temperatures, using zebrafish (Danio rerio) and guppies (Poecilia reticulata) as representative oviparous and viviparous species. We found that offspring thermal preference and avoidance of both species were significantly influenced by parental effects and developmental plasticity, with higher thermal preference and avoidance consistent with higher background (parental) temperature treatments. However, parental effects were only found to impose significant effect on the thermal tolerances of guppies. The findings suggest that phenotypic plasticity, both within and across generations, may be an important mechanism to adapt to rapid climate changes, and that future temperature fluctuations may impose more profound effects on viviparous fish species in general.
RESUMEN
The acceptorless dehydrogenative cross-coupling of primary alcohols to form cross-esters with the liberation of H2 gas was enabled using a [RuCl(η6-C6H6)(κ2-CNP)][PF6]Cl complex as the catalyst. This sustainable protocol is applicable to a broad range of primary alcohols, particularly for the sterically demanding ones, featuring good functional group tolerance and high selectivity. The good catalytic performance can be attributed to the nitrogen-phosphine-functionalized N-heterocyclic carbene (CNP) ligand, which adopts a facial coordination mode as well as the facile dissociation of coordinated benzene.
RESUMEN
Nucleophilic recyclization of pyridinium salts involving a CCN interchange ring transformation for the synthesis of 2-methylnicotinonitrile derivatives was herein developed. 3-Aminocrotononitrile (3-ACN) produced in situ from CH3CN acted as a C-nucleophile, as well as the source of CH3 and CN groups, which was supported by isotope-labeling and control experiments.
RESUMEN
Electrochemical reduction of carbon dioxide (CO2) to carbon monoxide (CO) is the first step in the synthesis of more complex carbon-based fuels and feedstocks using renewable electricity. Unfortunately, the reaction suffers from slow kinetics owing to the low local concentration of CO2 surrounding typical CO2 reduction reaction catalysts. Alkali metal cations are known to overcome this limitation through non-covalent interactions with adsorbed reagent species, but the effect is restricted by the solubility of relevant salts. Large applied electrode potentials can also enhance CO2 adsorption, but this comes at the cost of increased hydrogen (H2) evolution. Here we report that nanostructured electrodes produce, at low applied overpotentials, local high electric fields that concentrate electrolyte cations, which in turn leads to a high local concentration of CO2 close to the active CO2 reduction reaction surface. Simulations reveal tenfold higher electric fields associated with metallic nanometre-sized tips compared to quasi-planar electrode regions, and measurements using gold nanoneedles confirm a field-induced reagent concentration that enables the CO2 reduction reaction to proceed with a geometric current density for CO of 22 milliamperes per square centimetre at -0.35 volts (overpotential of 0.24 volts). This performance surpasses by an order of magnitude the performance of the best gold nanorods, nanoparticles and oxide-derived noble metal catalysts. Similarly designed palladium nanoneedle electrocatalysts produce formate with a Faradaic efficiency of more than 90 per cent and an unprecedented geometric current density for formate of 10 milliamperes per square centimetre at -0.2 volts, demonstrating the wider applicability of the field-induced reagent concentration concept.
RESUMEN
Electrochemical reduction of CO2 to useful chemicals has been actively pursued for closing the carbon cycle and preventing further deterioration of the environment/climate. Since CO2 reduction reaction (CO2RR) at a cathode is always paired with the oxygen evolution reaction (OER) at an anode, the overall efficiency of electrical energy to chemical fuel conversion must consider the large energy barrier and sluggish kinetics of OER, especially in widely used electrolytes, such as the pH-neutral CO2-saturated 0.5 M KHCO3 OER in such electrolytes mostly relies on noble metal (Ir- and Ru-based) electrocatalysts in the anode. Here, we discover that by anodizing a metallic Ni-Fe composite foam under a harsh condition (in a low-concentration 0.1 M KHCO3 solution at 85 °C under a high-current â¼250 mA/cm2), OER on the NiFe foam is accompanied by anodic etching, and the surface layer evolves into a nickel-iron hydroxide carbonate (NiFe-HC) material composed of porous, poorly crystalline flakes of flower-like NiFe layer-double hydroxide (LDH) intercalated with carbonate anions. The resulting NiFe-HC electrode in CO2-saturated 0.5 M KHCO3 exhibited OER activity superior to IrO2, with an overpotential of 450 and 590 mV to reach 10 and 250 mA/cm2, respectively, and high stability for >120 h without decay. We paired NiFe-HC with a CO2RR catalyst of cobalt phthalocyanine/carbon nanotube (CoPc/CNT) in a CO2 electrolyzer, achieving selective cathodic conversion of CO2 to CO with >97% Faradaic efficiency and simultaneous anodic water oxidation to O2 The device showed a low cell voltage of 2.13 V and high electricity-to-chemical fuel efficiency of 59% at a current density of 10 mA/cm2.
RESUMEN
Redox mediators (RMs) play a vital role in some liquid electrolyte-based electrochemical energy storage systems. However, the concept of redox mediator in solid-state batteries remains unexplored. Here, we selected a group of RM candidates and investigated their behaviors and roles in all-solid-state lithium-sulfur batteries (ASSLSBs). The soluble-type quinone-based RM (AQT) shows the most favorable redox potential and the best redox reversibility that functions well for lithium sulfide (Li2S) oxidation in solid polymer electrolytes. Accordingly, Li2S cathodes with AQT RMs present a significantly reduced energy barrier (average oxidation potential of 2.4 V) during initial charging at 0.1 C at 60 °C and the following discharge capacity of 1133 mAh gs-1. Using operando sulfur K-edge X-ray absorption spectroscopy, we directly tracked the sulfur speciation in ASSLSBs and proved that the solid-polysulfide-solid reaction of Li2S cathodes with RMs facilitated Li2S oxidation. In contrast, for bare Li2S cathodes, the solid-solid Li2S-sulfur direct conversion in the first charge cycle results in a high energy barrier for activation (charge to â¼4 V) and low sulfur utilization. The Li2S@AQT cell demonstrates superior cycling stability (average Coulombic efficiency 98.9% for 150 cycles) and rate capability owing to the effective AQT-enhanced Li-S reaction kinetics. This work reveals the evolution of sulfur species in ASSLSBs and realizes the fast Li-S reaction kinetics by designing an effective sulfur speciation pathway.
RESUMEN
Engineering high-performance electrocatalysts is of great importance for energy conversion and storage. As an efficient strategy, element doping has long been adopted to improve catalytic activity, however, it has not been clarified how the valence state of dopant affects the catalytic mechanism and properties. Herein, it is reported that the valence state of a doping element plays a crucial role in improving catalytic performance. Specifically, in the case of iridium doped nickel-iron layer double hydroxide (NiFe-LDH), trivalent iridium ions (Ir3+ ) can boost hydrogen evolution reaction (HER) more efficiently than tetravalent iridium (Ir4+ ) ions. Ir3+ -doped NiFe-LDH delivers an ultralow overpotential (19 mV @ 10 mA cm-2 ) for HER, which is superior to Ir4+ doped NiFe-LDH (44 mV@10 mA cm-2 ) and even commercial Pt/C catalyst (40 mV@ 10 mA cm-2 ), and reaches the highest level ever reported for NiFe-LDH-based catalysts. Theoretical and experimental analyses reveal that Ir3+ ions donate more electrons to their neighboring O atoms than Ir4+ ions, which facilitates the water dissociation and hydrogen desorption, eventually boosting HER. The same valence-state effect is found for Ru and Pt dopants in NiFe-LDH, implying that chemical valence state should be considered as a common factor in modulating catalytic performance.
RESUMEN
Herein, the synthesis of (Z)-α,ß-unsaturated nitriles by a sequential hydroformylation/Knoevenagel reaction has been first developed. A variety of crude α-olefins from Fischer-Tropsch synthesis, internal and special olefins, as well as alkynes could be transformed into value-added alkenyl nitriles (39 examples) up to 90% yield. Remarkably, compared with commonly used tedious multistep reactions, the one-pot protocol features cheap and easily available raw materials, excellent chemo-, regio-, and stereoselectivity, very mild reaction conditions, and easy scale-up production.
RESUMEN
The NaIO4-mediated sequential iodination/amidation reaction of N-alkyl quinolinium iodide salts has been first developed. This cascade process provides an efficient way to rapidly synthesize 3-iodo-N-alkyl quinolinones with high regioselectivity and good functional group tolerance. This protocol was also amenable to the isoquinolinium salts, thus providing a complementary method for preparing the 4-iodo-N-alkyl isoquinolinones.
RESUMEN
Solid-state Li-S batteries are attractive due to their high energy density and safety. However, it is unclear whether the concepts from liquid electrolytes are applicable in the solid state to improve battery performance. Here, we demonstrate that the nanoscale encapsulation concept based on Li2S@TiS2 core-shell particles, originally developed in liquid electrolytes, is effective in solid polymer electrolytes. Using in situ optical cell and sulfur K-edge X-ray absorption, we find that polysulfides form and are well-trapped inside individual particles by the nanoscale TiS2 encapsulation. This TiS2 encapsulation layer also functions to catalyze the oxidation reaction of Li2S to sulfur, even in solid-state electrolytes, proven by both experiments and density functional theory calculations. A high cell-level specific energy of 427 W·h·kg-1 is achieved by integrating the Li2S@TiS2 cathode with a poly(ethylene oxide)-based electrolyte and a lithium metal anode. This study points to the fruitful direction of borrowing concepts from liquid electrolytes into solid-state batteries.
RESUMEN
Converting CO2 and H2 O into carbon-based fuel by IR light is a tough task. Herein, compared with other single-component photocatalysts, the most efficient IR-light-driven CO2 reduction is achieved by an element-doped ultrathin metallic photocatalyst-Ni-doped CoS2 nanosheets (Ni-CoS2 ). The evolution rate of CH4 over Ni-CoS2 is up to 101.8â µmol g-1 h-1 . The metallic and ultrathin nature endow Ni-CoS2 with excellent IR light absorption ability. The PL spectra and Arrhenius plots indicate that Ni atoms could facilitate the separation of photogenerated carriers and the decrease of the activation energy. Moreover, in situ FTIR, DFT calculations, and CH4 -TPD reveal that the doped Ni atoms in CoS2 could effectively depress the formation energy of the *COOH, *CHO and desorption energy of CH4 . This work manifests that element doping in atomic level is a powerful way to control the reaction intermediates, providing possibilities to realize high-efficiency IR-light-driven CO2 reduction.
RESUMEN
An efficient Pd-catalyzed arylation of alkylpyridine based on the pyridinium activation strategy has been developed for synthesis of mixed aryl alkylpyridines. It was found that (1) the N-methyl group in the pyridinium salts acted as a transient activator and could be automatically departed after the reaction, (2) CuBr was an indispensable additive for achieving the C6-selective arylation, (3) the α-branched alkyl chain on the alkylpyridine greatly increased the yield of the product. Deuterium labelling experiment revealed that in the case of the α-branched alkylpyridine, the presence of CuBr completely inhibited the H/D exchange at the benzylic position and thus enabled the selective arylation at the C6 position. This protocol demonstrates a broad substrate scope, and with respect to both the aryl iodides and the α-branched alkylpyridine, the desired mixed aryl alkylpyridines were obtained in generally good to excellent yields.