Aggregation-Induced Enhanced Red Emission Graphene Quantum Dots for Integrated Fabrication of Luminescent Solar Concentrators.

Graphene quantum dots (GQDs) commonly suffer from the fluorescence problem of aggregation-caused quenching under high-concentration loading or in the solid state, which seriously hinders the application. Here we report a type of GQDs with red aggregation-induced enhanced emission (AIEE). It is confirmed that the aggregation state of the AIEE GQDs is a J-aggregate. The GQDs/poly(methyl methacrylate) film presented a photoluminescence quantum yield as high as 60.81%, and the record-high performance of luminescent solar concentrators (LSCs) was achieved. The power conversion efficiency (ηPCE) is up to 8.35% and the external optical efficiency (ηext) is ∼8.99% for the GQD-based LSCs (45 mW/cm2). Even under one sun illumination (100 mW/cm2), the corresponding ηPCE and ηext values are 3.12% and 4.52%, respectively. The internal photon efficiency (ηint) of an LSC device is about 5.02%. The synthesis of AIEE GQDs bridges the research gap in the emission mechanism of AIEE in GQDs.

Screening Surface-Defective Graphene Quantum Dots: Promoting Plant Growth and Combating Phytovirus.

Reduced graphene quantum dots (r-GQD), graphene oxide quantum dots (GOQD), and carboxylated graphene quantum dots (C-GQD) are screened to promote tobacco growth and combat tobacco mosaic virus (TMV). First, a 21-day foliar exposure is employed to explore GQDs' impacts on N. benthamiana. Surface-defective GOQD and C-GQD are screened out to facilitate N. benthamiana uptake through leaf stomata, and to promote seedlings of differently leaf ages to various degrees at different concentrations after different durations of foliar exposure. Specially, compared to the ddH2O treatment, GOQD/C-GQD at 400 mg L-1 increase biomass by 44%/68%, increase chlorophyll content by 43%/54% and up-regulate the expression of growth-related genes NtLRX1, CycB, and NtPIP1 by more than two-fold. Second, different from the transient inhibition shown by r-GQD and the TMV enhancement shown by GOQD, C-GQD can directly inactivate TMV infection by inducing TMV aggregation and attachment outside TMV, significantly decreasing TMV replication and hindering TMV spread over 21-day. Specially, C-GQD decreases the transcript abundance of TMV RdRp and TMV CP to 0.11-fold and 0.29-fold, and down-regulates the host defensive response pathways. This work provides a comparative analysis of GQDs with different surface-functionalizations, highlighting C-GQD as a promising nanotechnology tool for promoting plant growth and inactivating phytovirus.

Gram-Scale Mechanochemical Synthesis of Atom-Layer MoS2 Semiconductor Electrocatalyst via Functionalized Graphene Quantum Dots for Efficient Hydrogen Evolution.

The development of advanced and efficient synthetic methods is pivotal for the widespread application of 2D materials. In this study, a facile and scalable solvent-free mechanochemical approach is approached, employing graphene quantum dots (GQDs) as exfoliation agents, for the synthesis and functionalization of nearly atom-layered MoS2 nanosheets (ALMS). The resulting ALMS exhibits an ultrathin average thickness of 4 nm and demonstrates high solvent stability. The impressive yield of ALMS reached 63%, indicating its potential for scalable production of stable nanosheets. Remarkably, the ALMS catalyst exhibits excellent HER performance. Moreover, the ALMS catalyst showcases exceptional long-term durability, maintaining stable performance for nearly 200 h, underscoring its potential as a highly efficient and durable electrocatalyst. Significantly, the catalytic properties of ALMS are significantly influenced by ball milling production conditions. The GQD-assisted large-scale machinery synthesis pathway provides a promising avenue for the development of efficient and high-performance ultrathin 2D materials.

Single-layer graphene based resistive humidity sensor enhanced by graphene quantum dots.

Graphene is broadly applied as sensitive sensing material results from its superb features. Concurrently, as a derivative of graphene with 0D structure, graphene quantum dots (GQDs) offer more possibilities as a supportive sensing material due to its adjustable size and functional group modification. In this work, GQDs are introduced to single-layer graphene (SLG) based humidity sensor to enhance the sensing performance. Specifically, consistent resistance response to relative humidity (RH) is extended from the range of 10%-60% to 10%-90% by contrary to original SLG based sensor. Parallelly, effect of the amount of GQDs is investigated by means of multiple GQDs deposition. As the resultant higher binding efficiency between water molecules and the functional groups of GQDs, improved response rate is observed. For the case of 4-time deposition of GQDs, the response rate (ΔR/R) reaches ∼130% in RH range of 10%-90%. Besides, the response time and recovery time are ∼0.7 s and ∼1.1 s, respectively. The fluctuation of the resistance change of the sensor under constant humidity is less than 5% over a month which demonstrates long-term reliability.

A review on synthesis, properties, and biomedical applications of graphene quantum dots (GQDs).

A new type of 0-dimensional carbon-based materials called graphene quantum dots (GQDs) is gaining significant attention as a non-toxic and eco-friendly nanomaterial. GQDs are nanomaterials composed of sp2hybridized carbon domains and functional groups, with their lateral size less than 10 nm. The unique and exceptional physical, chemical, and optical properties arising from the combination of graphene structure and quantum confinement effect due to their nano-size make GQDs more intriguing than other nanomaterials. Particularly, the low toxicity and high solubility derived from the carbon core and abundant edge functional groups offer significant advantages for the application of GQDs in the biomedical field. In this review, we summarize various synthetic methods for preparing GQDs and important factors influencing the physical, chemical, optical, and biological properties of GQDs. Furthermore, the recent application of GQDs in the biomedical field, including biosensor, bioimaging, drug delivery, and therapeutics are discussed. Through this, we provide a brief insight on the tremendous potential of GQDs in biomedical applications and the challenges that need to be overcome in the future.

Simulating graphene-based single-electron transistor: incoherent current effects due to the presence of electron-electron interaction.

Carbon-based nanostructures have unparalleled electronic properties. At the same time, using an allotrope of carbon as the contacts can yield better device control and reproducibility. In this work, we simulate a single-electron transistor composed of a segment of a graphene nanoribbon coupled to carbon nanotubes electrodes. Using the non-equilibrium Green's function formalism we atomistically describe the electronic transport properties of the system including electron-electron interactions. Using this methodology we are able to recover experimentally observed phenomena, such as the Coulomb blockade, as well as the corresponding Coulomb diamonds. Furthermore, we separate the different contributions to transport and show that incoherent effects due to the interaction play a crucial role in the transport properties depending on the region of the stability diagram being considered.

Retinal Degeneration Response to Graphene Quantum Dots: Disruption of the Blood-Retina Barrier Modulated by Surface Modification-Dependent DNA Methylation.

Graphene quantum dots (GQDs) are used in diverse fields from chemistry-related materials to biomedicines, thus causing their substantial release into the environment. Appropriate visual function is crucial for facilitating the decision-making process within the nervous system. Given the direct interaction of eyes with the environment and even nanoparticles, herein, GQDs, sulfonic acid-doped GQDs (S-GQDs), and amino-functionalized GQDs (A-GQDs) were employed to understand the potential optic neurotoxicity disruption mechanism by GQDs. The negatively charged GQDs and S-GQDs disturbed the response to light stimulation and impaired the structure of the retinal nuclear layer of zebrafish larvae, causing vision disorder and retinal degeneration. Albeit with sublethal concentrations, a considerably reduced expression of the retinal vascular sprouting factor sirt1 through increased DNA methylation damaged the blood-retina barrier. Importantly, the regulatory effect on vision function was influenced by negatively charged GQDs and S-GQDs but not positively charged A-GQDs. Moreover, cluster analysis and computational simulation studies indicated that binding affinities between GQDs and the DNMT1-ligand binding might be the dominant determinant of the vision function response. The previously unknown pathway of blood-retinal barrier interference offers opportunities to investigate the biological consequences of GQD-based nanomaterials, guiding innovation in the industry toward environmental sustainability.

Detection of Tyrosinase Activity and Inhibitor Validation Based on N-GQDs Fluorescence Sensor.

Tyrosinase inhibitors have the ability to resist melanin formation and can be used for clinical and cosmetic, so it is becoming extremely crucial to search a rapid and effective method for detecting t the activity of tyrosinase. In this study, a sensing probe based on Nitrogen-doped graphene quantum dots (N-GQDs) were prepared with carbamide and citric acid. Tyrosinase can oxidize dopamine to dopamine quinone, which can quench the fluorescence of N-GQDs based on the principle of fluorescence resonance energy transfer (FRET) process, and then the detection of tyrosinase activity can be achieved. The result demonstrated that the fluorescence intensity of N-GQDs was a linear correlation with the activity of tyrosinase. Wide detection linear ranges between 0.05 and 5 U/mL and high selectivity. The detection range of tyrosinase was 0.05 to 5 U/mL and LOD of 0.005 U/mL. According to the above, the fluorescence method established in this work could be successfully used for the trace analysis of tyrosinase and it was verified that KA is an inhibitor of tyrosinase.

Recent Progress of Fluorescent Carbon Dots and Graphene Quantum Dots for Biosensors: Synthesis of Solution Methods and their Medical Applications.

In the fields of health and biology, fluorescent nanomaterials have emerged as highly potential and very useful candidates for use in biosensor applications. These typical highly powerful nanomaterials are carbon dots (CDs) and graphene quantum dots (GQDs) among many other metallic nanomaterials. In the context of medical biosensors, this review article investigates the techniques of synthesis, and many uses of these nanomaterials, the obstacles that they face, and the potential for their future. We cover the significance of fluorescent nanomaterials, their use in the medical field, as well as the several techniques of synthesis for CDs and GQDs, including ultrasonication, hydrothermal, electrochemical method, surface modification, and solvothermal. In addition, we also discuss their biomedical applications, which include biomolecule detection, disease diagnosis and examine the obstacles and prospective possibilities for development of ultra-bright, ultra-sensitive, and selective biosensors for use in in-vivo research.Fluorescent carbon dots and graphene quantum dots is synthesized by using several types of raw material and methods. These Carbon dots and graphene quantum dots are used in the medical field includes detection of biomaterials, detection of cancer, virus and mutation in DNA.

Fluorescent Probes Based on Ag NPs@N/GQDs and Molecularly Imprinted Polymer for Sensitive Detection of Noradrenaline in Bananas.

Fluorescence intensity and selective recognition ability are crucial factors in determining the analytical techniques for fluorescent probes. In this study, a core-shell fluorescent material, composed of silver nanoparticles@nitrogen-doped graphene quantum dots (Ag NPs@N/GQDs), was synthesised using mango leaves as the raw material through a thermal cracking method, resulting in strong fluorescence luminescence intensity. By employing noradrenaline as a template molecule and using a surface molecular imprinting technique, a molecularly imprinted membrane (MIP) was formed on the surface of the fluorescent material, that was subsequently eluted to obtain a highly specific, fluorescent probe capable of recognising noradrenaline. The probe captured various concentrations of noradrenaline using the MIP, which decreased the fluorescence intensity. Then a method for detecting trace amounts of noradrenaline was established. This method exhibited a linear range from 0.5 -700 pM with a detection limit of 0.154 pM. The proposed method was implemented in banana samples. Satisfactory recoveries were confirmed at four different concentrations. The method presented a relative standard deviation (RSD) of less than 5.0%.

Highly Sensitive and Selective Fluorescence and Smartphone-Based Sensor for Detection of Rutin Using Boron Nitrogen Co-doped Graphene Quantum Dots.

This research explores the fluorescence properties and photostability of boron nitrogen co-doped graphene quantum dots (BN-GQDs), evaluating their effectiveness as sensors for rutin (RU). BN-GQDs are biocompatible and exhibit notable absorbance and fluorescence characteristics, making them suitable for sensing applications. The study utilized various analytical techniques to investigate the chemical composition, structure, morphology, optical attributes, elemental composition, and particle size of BN-GQDs. Techniques included X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The average particle size of the BN-GQDs was determined to be approximately 3.5 ± 0.3 nm. A clear correlation between the emission intensity ratio and RU concentration was identified across the range of 0.42 to 4.1 µM, featuring an impressively low detection limit (LOD) of 1.23 nM. The application of BN-GQDs as fluorescent probes has facilitated the development of a highly sensitive and selective RU detection method based on Förster resonance energy transfer (FRET) principles. This technique leverages emission at 465 nm. Density Functional Theory (DFT) analyses confirm that FRET is the primary mechanism behind fluorescence quenching, as indicated by the energy levels of the lowest unoccupied molecular orbitals (LUMOs) of BN-GQDs and RU. The method's effectiveness has been validated by measuring RU concentrations in human serum samples, showing a recovery range between 97.8% and 103.31%. Additionally, a smartphone-based detection method utilizing BN-GQDs has been successfully implemented, achieving a detection limit (LOD) of 49 nM.

Analytical control of imatinib in bioanalytical samples using graphene quantum dots sensing.

An analytical method for the determination of imatinib (IMA, the primary treatment for chronic myeloid leukemia), based on the fluorescence properties of graphene quantum dots (GQDs), is reported in this work. The method is addressed to the analytical control of IMA in biological and pharmaceutical samples, due to the present interest in the control of the doses of this anticancer drug, as well as the therapeutic monitoring. The whole method involves the use of a solid-phase extraction (SPE) procedure, followed by an evaporation step, for the treatment of biological samples. For that, tC18 sorbent cartridges were used. After the sample treatment, the solution containing the analyte was mixed with an aqueous solution of GQDs at pH 7.2, and the fluorescent quenching of GQDs was measured. IMA was determined in the 10-250 µg L-1 range, with a limit of detection of 21 µg L-1 and a precision of 1.5% as relative standard deviation, measured in terms of reproducibility. The recovery for biological samples was in the 84-113% range.

Selective dual sensing strategy for free and vitamin D3 micelles in food samples based on S,N-GQDs photoinduced electron transfer.

A reliable nanotechnological sensing strategy, based on an S,N-co-doped graphene quantum dot (GQD) platform, has been developed to distinctly detect two key variants of vitamin D3, specifically the free (VD3) and the nanoencapsulated form (VD3Ms). For this purpose, food-grade vitamin D3 micelles were self-assembled using a low-energy procedure (droplet size: 49.6 nm, polydispersity index: 0.34, ζ-potential: -33 mV, encapsulation efficiency: 90 %) with an innovative surfactant mixture (Tween 60 and quillaja saponin). Herein, four fluorescent nanoprobes were also synthesized and thoroughly characterized: S,N-co-doped GQDs, α-cyclodextrin-GQDs, ß-cyclodextrin-GQDs, and γ-cyclodextrin-GQDs. The goal was to achieve a selective dual sensing strategy for free VD3 and VD3Ms by exploiting their distinctive quenching behaviors. Thus, the four nanosensors allowed the individual sensing of both targets to be performed (except α-CD-GQD for VD3Ms), but S,N-GQDs were finally selected due to selectivity and sensitivity (quantum yield, QY= 0.76) criteria. This choice led to a photoinduced electron transfer (PET) mechanism associated with static quenching, where differentiation was evidenced through a displayed 13-nm hypsochromic (blue) shift when interacting with VD3Ms. The reliability of this dual approach was demonstrated through an extensive evaluation of analytical performance characteristics. The feasibility and accuracy were proven in commercial food preparations and nutritional supplements containing declared nanoencapsulated and raw VD3, whose results were validated by a paired Student's t-test comparison with a UV-Vis method. To the best of our knowledge, this represents the first non-destructive analytical approach addressing the groundbreaking foodomic trend to distinctly detect different bioactive forms of vitamin D3, while also preserving their native nanostructures as a chemical challenge, thus providing reliable information about their final stability and bioavailability.

Low cost fabrication of continuous flow optofluidic microreactor for efficient dye degradation using graphene QDs@MOF (Ti) photocatalyst.

The optofluidic microreactor, a convergence of optics and microfluidics, offers advanced functionalities that can be pivotal in the rapid assessment of nanocatalysts for tackling environmental contamination issues. This article presents an efficient approach for degrading Methylene blue (MB) dye, commonly used in the textile industry, within a cost-effective polydimethylsiloxane (PDMS) based continuous flow optofluidic microreactor. This microreactor combines graphene quantum dots (QDs) and NH2-MIL-125 (MOF(Ti)) as a highly effective photocatalyst coating within its microchannels. By directly incorporating graphene QDs@MOF(Ti) into the microchannels, the photocatalytic medium is brought into close proximity with the flowing MB dye solutions, thereby reducing the necessary interaction time and enhancing purification efficiency. Furthermore, the findings demonstrate an impressive degradation efficiency of ∼99% for MB dye at a flow rate of 50 µL min-1 under visible light irradiation, achieved in a single pass. Additionally, the microfluidic reactor exhibits prolonged stability of the photocatalyst, enabling its reuse without significant efficiency loss. In addition, a comparative analysis highlights the advantages of microreactor-based photocatalysis over traditional methods. These advancements in the features of the graphene QDs@MOF(Ti) nanocomposite substantiate their demonstrated superiority in degradation efficiency.

Fabrication of highly fluorescent graphene quantum dots for quantification of As3+ ion using modified cellulose paper.

Easy, economical, and swift detecting tools are very demanded for assaying various chemical species. The introduction of label-free paper-based read-out devices has significantly reached the demand of analytical science for target analytes assays. Herein, a facile, and disposable inexpensive paper-based sensing tool was fabricated for sensing As3+ ion using graphene quantum dots (GQDs) as a fluorescent reader. The CA-GQDs were synthesized using citric acid (CA) as a precursor via the pyrolysis method, further physisorbed on the cellulose substrate for sensing of As3+ via aggregation-based fluorescence "turn-off" mechanism. The linear range for quantitating As3+ ion is in the range of 0.05-50 µM with a detection limit of 10 nM. The practical application of the CA-GQDs-based analytical platform was verified by assaying As3+ ion in water samples. The CA-GQDs-embedded paper strip can be easily extended for assaying of As3+ ion, which meets the demand for monitoring of As3+ ion in real samples.

An innovative strategy for Gefitinib quantification in pharmaceutical and plasma samples using a graphene quantum dots-combined gold nanoparticles composite electrochemical sensor.

An innovative methodology is proposed for quantifying Gefitinib (GFT) using an electrochemical sensor constructed from a composite of graphene quantum dots (GQDs) and gold nanoparticles (AuNPs). GQDs were synthesized from graphite, preserving graphene's large surface area and excellent electron transfer capabilities while enhancing dispersibility. The combination of GQDs with AuNPs resulted in an AuNPs@GQDs composite, which was used to construct the sensor. The synthesized nanomaterials were characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), and the electrochemical performance of the sensor was evaluated via cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Under optimized conditions, the sensor displayed a linear calibration curve for GFT detection within the range 0.01 to 10.0 µM, with a limit of detection (LOD) of 0.005 µM (S/N = 3). The sensor demonstrated excellent anti-interference properties and stability in tests using pharmaceutical formulations and plasma samples. Compared to chromatographic methods, the sensor exhibited similar accuracy and recovery. Its easy fabrication and high sensitivity make it a promising tool for pharmaceutical analysis and clinical therapeutic drug monitoring.

An electrochemical immunosensor based on MXene-GQD/AuNPs for the detection of trace amounts of CA-125 as specific tracer of ovarian cancer.

An electrochemical immunoassay system was developed to detect CA-125 using a glassy carbon electrode (GCE) modified with MXene, graphene quantum dots (GQDs), and gold nanoparticles (AuNPs). The combined MXene-GQD/AuNPs modification displayed advantageous electrochemical properties due to the synergistic effects of MXene, GQDs, and AuNPs. The MXene-GQD composite in the modified layer provided strong mechanical properties and a large specific surface area. Furthermore, the presence of AuNPs significantly improved conductivity and facilitated the binding of anti-CA-125 on the modified GCE, thereby enhancing sensitivity. Various analytical techniques such as FE-SEM and EDS were utilized to investigate the structural and morphological characteristics as well as the elemental composition. The performance of the developed immunosensor was assessed using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), square wave voltammetry (SWV), and differential pulse voltammetry (DPV). Under optimized conditions in a working potential range of -0.2 to 0.6 V (vs. Ag/AgCl), the sensitivity, linear range (LR), limit of detection (LOD), and correlation coefficient (R2) were determined to be 315.250 µA pU.mL-1/cm2, 0.1 to 1 nU/mL, 0.075 nU/mL, and 0.9855, respectively. The detection of CA-125 in real samples was investigated using the developed immunoassay platform, demonstrating satisfactory results including excellent selectivity and reproducibility.

Graphene quantum dots modified electrodes as electrochemical sensing tool towards the detection of codeine in biological fluids and soft drinks.

An electroanalytical method based on disposable screen-printed carbon electrodes modified with non-toxic carbonaceous nanodots is proposed as a reliable and effective device for codeine determination in biological fluids and soft drinks. Graphene quantum dots (GQDs), carbon quantum dots (CQDs) and carbon nanodots (CNDs) were evaluated as electrode modifiers for the determination of the drug. The electroactive areas of the modified electrodes were assessed by cyclic voltammetry using potassium ferricyanide. Results demonstrated that GQDs provided the best analytical response for codeine, displaying an intense and well-defined anodic wave approximately 0.9 V vs reference electrode. The method exhibits an acceptable linear dynamic range, low limits of detection and quantification (0.21 and 0.73 µM, respectively), and satisfactory precision (below 3.9% expressed as relative standard deviation (RSD)) in saliva. Only the analysis of biofluids requires a simple extraction protocol. The feasibility and applicability of this novel approach were assessed by determining codeine in different matrices, with recoveries ranging from 69 to 112%. This cost-effective, simple, easily miniaturised and portable method was applied not only to biofluids but also for the direct detection of codeine in soft drinks combined with a codeine-enriched syrup, a medication that is being used to adulterate beverages, particularly at specific events (drinking and nightclub parties). There is no need for any sample treatment, demonstrating its versatility in analysing beverages for potential adulteration as well.

Fluorescence/electrochemical dual-mode strategy for Golgi protein 73 detection based on molybdenum disulfide/ferrocene/palladium nanoparticles and nitrogen-doped graphene quantum dots.

Golgi protein 73 (GP73) is a new serum marker associated with early diagnosis and postoperative assessment of hepatocellular carcinoma (HCC). Herein, an electrochemical/fluorescence dual-signal biosensor was designed for determination of GP73 based on molybdenum disulfide/ferrocene/palladium nanoparticles (MoS2-Fc-PdNPs) and nitrogen-doped graphene quantum dots (NGQDs). GP73 aptamer (Apt) was labeled with NGQDs to form the NGQDs-Apt fluorescence probe. MoS2-Fc-PdNPs served not only as the fluorescence quencher but also as electrochemical enhancer. The sensing platform (NGQDs-Apt/MoS2-Fc-PdNPs) was formed based on the fluorescence resonance energy transfer (FRET) mechanism. In the presence of GP73, the specific binding of NGQDs-Apt to GP73 interrupted FRET, restoring the fluorescence of NGQDs-Apt at λex/em = 348/438 nm and enhancing the oxidation current of Fc in MoS2-Fc-PdNPs at 0.04 V through differential pulse voltammetry (DPV). Under the optimal conditions, the DPV current change and fluorescence recovery have a good linear relationship with GP73 concentration from 1.00 to 10.0 ng/mL. The calibration equation for the fluorescence mode was Y1 = (0.0213 ± 0.00127)X + (0.0641 ± 0.00448) and LOD was 0.812 ng/mL (S/N = 3). The calibration equation of the electrochemical mode was Y2 = (3.41 ± 0.111)X + (1.62 ± 0.731), and LOD of 0.0425 ng/mL (S/N = 3). The RSDs of fluorescence mode and electrochemical mode after serum detection were 1.62 to 5.21% and 0.180 to 6.62%, respectively. By combining the electrochemical and fluorescence assay, more comprehensive and valuable information for GP73 was provided. Such dual-mode detection platform shows excellent reproducibility, stability, and selectivity and has great application potential.

Exploration of the Graphene Quantum Dots-Blue Light Combination: A Promising Treatment against Bacterial Infection.

Graphene Quantum Dots (GQDs) have shown the potential for antimicrobial photodynamic treatment, due to their particular physicochemical properties. Here, we investigated the activity of three differently functionalized GQDs-Blue Luminescent GQDs (L-GQDs), Aminated GQDs (NH2-GQDs), and Carboxylated GQDs (COOH-GQDs)-against E. coli. GQDs were administrated to bacterial suspensions that were treated with blue light. Antibacterial activity was evaluated by measuring colony forming units (CFUs) and metabolic activities, as well as reactive oxygen species stimulation (ROS). GQD cytotoxicity was then assessed on human colorectal adenocarcinoma cells (Caco-2), before setting in an in vitro infection model. Each GQD exhibits antibacterial activity inducing ROS and impairing bacterial metabolism without significantly affecting cell morphology. GQD activity was dependent on time of exposure to blue light. Finally, GQDs were able to reduce E. coli burden in infected Caco-2 cells, acting not only in the extracellular milieu but perturbating the eukaryotic cell membrane, enhancing antibiotic internalization. Our findings demonstrate that GQDs combined with blue light stimulation, due to photodynamic properties, have a promising antibacterial activity against E. coli. Nevertheless, we explored their action mechanism and toxicity on epithelial cells, fixing and standardizing these infection models.