Fabrication of Chitosan-Based Intumescent Flame Retardant Coating for Improving Flame Retardancy of Polyacrylonitrile Fabric.

In order to improve the flame retardancy of polyacrylonitrile (PAN) fabrics, glycidyl methacrylate (GMA) was first grafted onto the surface of PAN fabric (PAN-g-GMA) by means of UV-induced photo grafting polymerization process. Then, PAN-g-GMA was chemically grafted with chitosan to obtain a bigrafted PAN fabric (PAN-g-GMA-g-CS). Finally, the flame-retardant PAN fabric (FR-PAN) was prepared by phosphorylation. The structure and elemental analysis of the samples were characterized by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The thermal degradation properties and combustion characteristics of the fabrics were accessed by thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and cone calorimeter (CC). The results show that the onset thermal decomposition temperature of FR-PAN fabric is lower than that of the control sample due to the degradation of the grafting groups. The combustion test indicates that the FR-PAN fabric has an excellent flame-retardant property and the combustion rate is significantly reduced. In addition, the char residue of the burned FR-PAN fabric is over 97%, indicating excellent char-forming ability.

Hollow Capsules with Multiresponsive Valves for Controlled Enzymatic Reactions.

The current challenge for polymeric nanoreactors is to precisely control the membrane permeability between permeable, impermeable, and semipermeable at defined pH. Additionally, the synthetic methods are obstructed by tedious purification processes, especially when polymer multiblocks are required in the membrane of capsules to achieve different responsiveness and functions. Here, we report a rapid one-pot synthesis of ABA-type triblock copolymer brushes on silica template via surface-initiated single electron transfer living radical polymerization (SI-SET-LRP). It is worth noting that there is no purification between the successive block formation steps, since each step is taken to full translation within 20 min. After removing the template, hollow capsules with cross-linked membrane are obtained and have been used as multiresponsive nanoreactors for enzymatic reactions. Their membrane permeability is triggered primarily by temperature and secondarily by pH to allow controlled enzymatic reactions to be reversibly addressable between "permeable", "semipermeable", and "impermeable" valve-like membrane status. These valve-like features highlight the significant potential of hollow capsules, for example, in the fields of synthetic biology and enzyme-deficient disease therapeutic applications.

Enhanced dewaterability of waste-activated sludge by combined cationic polyacrylamide and magnetic field pretreatment.

The potential function of combining magnetic field (MF) pretreatment with cationic polyacrylamide (CPAM) additive on enhancing the dewaterability of waste-activated sludge was investigated in the present work. Two reactors were involved in a specially designed experimental apparatus, one of which was built with MF accessories. Several parameters were conducted, including CPAM dosages, MF strengths and processing times, respectively. Capillary suction time (CST) and specific resistance to filtration (SRF) were used to evaluate sludge dewaterability. Extracellular polymeric substances (EPS) concentration was also determined in an attempt to identify the observed changes in dewaterability. It was indicated by the results that both CPAM conditioning and MF pretreatment on sludge can lower CST and SRF values. However, subjecting to a combination of MF pretreatment and CPAM conditioning, sludge dewaterability was significantly enhanced beyond the level observed of CPAM addition alone. The lowest CST and SRF values of 36.5 s and 0.75×10(12) m kg(-1), respectively, were obtained when sludge was co-conditioned by CPAM (at a dosage of 40 mg L(-1)) and MF (at an induction of 40 mT) for 30 min, suggesting the optimal condition for enhancing sludge dewaterability. It is also shown from the significant correlations between EPS, protein, polysaccharide and CST/SRF that the increment of EPS concentration in sludge supernatant may be the major reason for the enhancement of dewaterability.

Effect of light aging on silicone-resin bond strength in maxillofacial prostheses.

PURPOSE: The aim of this study was to investigate the effect of accelerated light aging on bond strength of a silicone elastomer to three types of denture resin. MATERIALS AND METHODS: A total of 60 single lap joint specimens were fabricated with auto-, heat-, and photopolymerized (n = 20) resins. An addition-type silicone elastomer (Episil-E) was bonded to resins treated with the same primer (A330-G). Thirty specimens served as controls and were tested after 24 hours, and the remaining were aged under accelerated exposure to daylight for 546 hours (irradiance 765 W/m(2) ). Lap shear joint tests were performed to evaluate bond strength at 50 mm/min crosshead speed. Two-way ANOVA and Tukey's test were carried out to detect statistical significance (p < 0.05). RESULTS: ANOVA showed that the main effect of light aging was the most important factor determining the shear bond strength. The mean bond strength values ranged from 0.096 to 0.136 MPa. The highest values were recorded for auto- (0.131 MPa) and photopolymerized (0.136 MPa) resins after aging. CONCLUSIONS: Accelerated light aging for 546 hours affects the bond strength of an addition-type silicone elastomer to three different denture resins. The bond strength significantly increased after aging for photo- and autopolymerized resins. All the bonds failed adhesively.

The effect of repeated microwave irradiation on the dimensional stability of a specific acrylic denture resin.

PURPOSE: To determine the dimensional stability of a poly(methyl methacrylate) (PMMA) acrylic resin when subjected to multiple sessions of repeated microwave irradiation at power settings of 700 and 420 W. MATERIALS AND METHODS: Twenty standardized denture bases were fabricated using a PMMA resin. Points of measurement were marked on each denture base with a standardized template, and the distances between points were recorded using a digital microscope. The denture bases were randomly placed into two experimental groups of 10 bases each. Individual denture bases were placed into a glass beaker containing 200 ml of room temperature deionized water and then exposed to either 700 or 420 W of microwave radiation for 3 minutes. The denture bases were allowed to cool to room temperature, and measurements between points were recorded. This process was carried out for two microwave periods with measurements being completed after each period. The data were then analyzed for any significant changes in distances between points using a Student's t-test. RESULTS: All denture bases experienced 1.0 to 2.0 mm or approximately 3% linear dimensional change after each period of microwaving. Results were significant with all t-tests having values of p < 0.05. CONCLUSION: This report showed that the denture bases deformed significantly under experimental conditions at either 700 W for 3 minutes in 200 ml of water or 420 W for 3 minutes in 200 ml of water.

Direct patterning of poly(acrylic acid) on polymer surfaces by ion beam lithography for the controlled adhesion of mammalian cells.

Poly(acrylic acid) (PAA)-patterned polystyrene (PS) substrates were prepared by ion beam lithography to control cell behaviors of mouse fibroblasts and human embryonic kidney cells. Thin PAA films spin-coated on non-biological PS substrates were selectively irradiated with energetic proton ions through a pattern mask. The irradiated substrates were developed with deionized water to generate negative-type PAA patterns. The surface characteristics of the resulting PAA-patterned PS surface, such as surface morphology, chemical structure and composition and wettability, were investigated. Well-defined 100 µm PAA patterns were effectively formed on relatively hydrophobic PS substrates by ion beam lithography at higher fluences than 5 × 10(14) ions/cm(2). Moreover, based on the in vitro cell culture test, cells were adhered and proliferated favorably onto hydrophilic PAA regions separated by hydrophobic PS regions on the PAA-patterned PS substrates, and thereby leading to the formation of well-defined cell patterns.

A technique to splint and verify the accuracy of implant impression copings with light-polymerizing acrylic resin.

Transferring the implant position from the mouth to the definitive cast is one of the most critical steps in implant prosthodontics. To achieve a passive fit of the prosthesis, an accurate implant impression is crucial because discrepancies can induce both biologic and technical complications. Analysis of available research data suggests that a direct (pick-up) impression technique with splinted copings is the technique of choice, particularly for multiple implants. However, the traditional method of splinting the copings with autopolymerizing acrylic resin is a technique-sensitive and time- consuming procedure. This report describes a straightforward method of splinting impression copings with light-polymerizing acrylic resin, with minimal amount of autopolymerizing acrylic resin. The method also can be used to verify splinting accuracy.

Shear bond strength of denture teeth to two chemically different denture base resins after various surface treatments.

PURPOSE: Debonding of acrylic teeth from the denture base remains a major problem in prosthodontics. The objective of this study was to evaluate the effect of various surface treatments on the shear bond strength of the two chemically different denture base resins-polymethyl methacrylate (PMMA) and urethane dimethacrylate (UDMA). MATERIALS AND METHODS: Two denture base resins, heat-cured PMMA (Meliodent) and light-activated UDMA (Eclipse), were used in this study. A total of 60 molar acrylic denture teeth were randomly separated into four groups (n = 15), according to surface treatment: acrylic untreated (group AC), Eclipse untreated (group EC), treated with eclipse bonding agent (group EB), and Er:YAG laser-irradiated eclipse (group EL). Shear bond strength test specimens were prepared according to the manufacturers' instructions. Specimens were subjected to shear bond strength test by a universal testing machine with a 1 mm/min crosshead speed. The data were analyzed with one-way ANOVA and post hoc Tukey-Kramer multiple comparison tests (α = 0.05). RESULTS: The highest mean bond strength was observed in specimens of group EB, and the lowest was observed in group EC specimens. A statistically significant difference in shear bond strength was found among all groups (p < 0.001), except between groups EC and EL (p = 0.61). CONCLUSION: The two chemically different denture base polymers showed different shear bond strength values to acrylic denture teeth. Laser-irradiation of the adhesive surface was found to be ineffective on improving bond strength of acrylic denture teeth to denture base resin. Eclipse bonding agent should be used as a part of denture fabrication with the Eclipse Resin System.

The impact of polymerization method on tensile bond strength between denture base and acrylic teeth.

Failure of the bond between acrylic teeth and the denture base resin interface is one of the major concern in prosthodontics. The new generation of denture bases that utilize alternate polymerization methods are being introduced in the market. The aim of the study is to evaluate the influence of polymerization methods on bonding quality between the denture base and artificial teeth. Sixty test specimens were prepared (20 in each group) and were polymerized using heat, microwave and visible light curing. The tensile strength was recorded for each of the samples, and the results were analyzed statistically. The light-activated Eclipse™ System showed the highest tensile strength, followed by heat curing. The microwave-cured samples exhibited the least bonding to the acrylic teeth. Within the limitations of this study, it can be concluded that the new generation of light-cured denture bases showed significantly better bonding to acrylic teeth and can be used as an alternative to the conventional heat-polymerized denture base.

Indigenously developed multipurpose acrylic head phantom for verification of IMRT using film and gel dosimetry.

The purpose of this study was to validate the newly designed acrylic phantom for routine dosimetric purpose in radiotherapy. The phantom can be used to evaluate and compare the calculated dose and measured dose using film and gel dosimetric methods. In this study, a doughnut-shaped planning target volume (8.54 cm3) and inner organ at risk (0.353 cm3) were delineated for an IMRT test plan using the X-ray CT image of the phantom. The phantom consists of acrylic slabs which are integrated to form a human head with a hole in the middle where several dosimetric inserts can be positioned for measurement. An inverse planning with nine coplanar intensity-modulated fields was created using Pinnacle TPS. For the film analysis, EBT2 film, flatbed scanner, in-house developed MATLAB codes and ImageJ software were used. The 3D dose distribution recorded in the MAGAT gel dosimeter was read using a 1.5 T MRI scanner. Scanning parameters were CPMG pulse sequence with 8 equidistant echoes, TR = 5600, echo step = 22 ms, pixel size = 0.5 × 0.5, slice thickness = 2 mm. Using a calibration relationship between absorbed dose and spin-spin relaxation rate (R2), R2 images were converted to dose images. The dose comparison was accomplished using in-house MATLAB-based graphical user interface named "IMRT3DCMP". For gel measurement dose grid from the TPS was extracted and compared with the measured dose grid of the gel. Gamma index analysis of film measurement for the tolerance criteria of 2%/2mm, 1%/1 mm showed more than 90% voxels pass rate. Gamma index analysis of 3D gel measurement data showed more than 90% voxels pass rate for different tolerance criteria of 2%/2 mm and 1%/1 mm. Overall both 2D and 3D measurement were in close agreement with the Pinnacle TPS calculated dose. The phantom designed is cost-effective and the results are promising, but further investigation is required to validate the phantom with other 3D conformal techniques for dosimetric purpose.

Ultrasonic measurement of the effects of adhesive application and power density on the polymerization behavior of core build-up resins.

OBJECTIVE: To use ultrasonic measurements to monitor the effects of adhesive application and power density on the polymerization behavior of dual-cured core build-up resins. METHODS: Ultrasonic measurements were carried out using a pulser-receiver, transducers and an oscilloscope. The core build-up resins were mixed, inserted into a transparent mold and then placed onto a sample stage with or without self-etch adhesive. Power densities of 0 (no light irradiation), 200 and 600 mW/cm(2) were used for curing. The transit time through the core build-up resin disk was divided by the specimen thickness to obtain the longitudinal sound velocity (V). RESULTS: Light irradiation of the core build-up resins at a power density of 600 mW/cm(2) caused V values to rise to an initial plateau of 1550-1650 m/s, then to rise rapidly to a second plateau of 2800-3200 m/s. The rate of V increase was slower when the resin cements were light-irradiated and became faster when irradiated at a higher power density. There were no significant differences between the groups with or without adhesive. CONCLUSIONS: The polymerization behavior of the core build-up resins was affected by the power density of the curing unit. The influence of adhesive application differed among the core build-up resins tested.

EFFECT OF LIGHT CURING UNIT CHARACTERISTICS ON LIGHT INTENSITY OUTPUT, DEPTH OF CURE AND SURFACE MICRO-HARDNESS OF DENTAL RESIN COMPOSITE.

BACKGROUND: Modern dental composite restorations are wholly dependent on the use of Visible Light Curing devices. The characteristics of these devices may influence the quality of composite resin restorations. OBJECTIVE: To determine the characteristics of light curing units (LCUs) in dental clinics in Nairobi and their effect on light intensity output, depth of cure (DOC) and surface micro-hardness (SMH) of dental resin composite. DESIGN: Laboratory based, cross-sectional analytical study. SETTING: Public and private dental clinics in Nairobi, Kenya. SUBJECTS: Eighty three LCUs which were in use in private and public dental health facilities in Nairobi, Kenya and resin composite specimens. RESULTS: Of the 83 LCUs studied, 43 (51.8%) were Light Emitting Diodes (LEDs) and 39(47.0%) were Quartz-Tungsten-Halogen (QTH) and 1 (1.2%) was Plasma Arc Curing (PAC) light. Mean light intensity for QTH and LED lights was 526.59 mW/cm2 and 493.67 mW/cm2 respectively (p=0.574), while the mean DOC for QTH lights was 1.71 mm and LED was 1.67 mm (p=0.690). Mean Vickers Hardness Number (VHN) for LED was 57.44 and for QTH was 44.14 (p=0.713). Mean light intensity for LCUs < or = 5 years was 596.03 mW/cm2 and 363.17 mW/cm2 for units > 5 years old (p=0.024). The mean DOC for the two age groups was 1.74 mm and 1.57 mm respectively (p=0.073). For SMH, the < or = 5 years and >5 years age groups gave a mean VHN of 58.81 and 51.46 respectively (p=0.1). On maintenance history, the frequency of routine inspection, duration since the last repair/replacement of a part or other maintenance activity and the nature of the last maintenance activity were determined and were not found to have influenced the light intensity, DOC and SMH. CONCLUSION: The LCU age has a statistically significant influence on its light intensity (p=0.024) while the type and maintenance history have no significant influence on its light intensity and composite DOC and SMH (p=0.574, p=0.690, p=0.713 respectively).

Effects of the peracetic acid and sodium hypochlorite on the colour stability and surface roughness of the denture base acrylic resins polymerised by microwave and water bath methods.

OBJECTIVE: This study evaluated the surface roughness (Ra) and color stability of acrylic resin colors (Lucitone 550, QC-20 and Vipi-Wave) used for fabricating bases for complete, removable dentures, overdentures and prosthetic protocol after immersion in chemical disinfectants (1% sodium hypochlorite and 2% peracetic acid) for 30 and 60 minutes. MATERIAL AND METHODS: Sixty specimens were made of each commercial brand of resin composite, and divided into 2 groups according to the chemical disinfectants. Specimens had undergone the finishing and polishing procedures, the initial color and roughness measurements were taken (t=0), and after this, ten test specimens of each commercial brand of resin composite were immersed in sodium hypochlorite and ten in peracetic acid, for 30 and 60 minutes, with measurements being taken after each immersion period. These data were submitted to statistical analysis. RESULTS: There was evidence of an increase in Ra after 30 minutes immersion in the disinfectants in all the resins, with QC-20 presenting the highest Ra values, and Vipi-Wave the lowest. After 60 minutes immersion in the disinfectants all the resins presented statistically significant color alteration. CONCLUSIONS: Disinfection with 1% sodium hypochlorite and peracetic acid altered the properties of roughness and color of the resins.

Adding denture cleanser to microwave disinfection regimen to reduce the irradiation time and the exposure of dentures to high temperatures.

BACKGROUND: The microwave energy is an efficient disinfection method; however, it can generate high temperatures that can result in distortion of the dentures. OBJECTIVES: To evaluate whether the addition of an enzymatic cleanser to microwave disinfection regimen would disinfect dentures with shorter irradiation time. MATERIALS AND METHODS: Seven resin discs colonized with Candida albicans biofilm were placed on the palatal surface of sterile dentures to be randomly assigned to the following treatments: immersion in distilled water for 3 min with 0 (DW), 1 (DW + M1), 2 (DW + M2), or 3 min (DW + M3) of microwave irradiation; or immersion in denture cleanser for 3 min with 0 (DC), 1 (DC + M1), 2 (DC + M2) or 3 min (DC + M3) of irradiation. After the treatments, the viable cells were counted by a blinded examiner. The temperature was measured immediately after irradiation. The data were analyzed by ANOVA and Tukey post hoc tests (α = 0.05). RESULTS: No viable cells were found after DC + M2, DC + M3, and DW + M3 treatments, of which DC + M2 achieved the lowest temperature. No significant difference was found between the effectiveness of DW, DW + M1 and DC treatments (p > 0.05). CONCLUSION: Within the limits of this study, the association of a denture cleanser and microwave energy is efficient to disinfect dentures in lower irradiation time and temperature.

Effect of chemical and microwave disinfection on the surface microhardness of acrylic resin denture teeth.

PURPOSE: The purpose of this study was to evaluate the effect of simulated disinfections (2% glutaraldehyde, 1% sodium hypochlorite, and microwave energy) on the surface hardness of Trilux, Biocler, Biotone, New Ace, and Magister commercial artificial teeth. MATERIALS AND METHODS: Specimens (n = 10) were made with the teeth included individually in circular blocks of acrylic resin, leaving the labial surface exposed. Cycles of simulated chemical disinfection were accomplished with the specimens immersed in the solutions at room temperature for 10 minutes, followed by tap water washing for 30 seconds and storage in distilled water at room temperature for 7 days until the next disinfection. Simulated disinfection by microwave energy was carried out in a domestic oven with 1300 W at a potency of 50% for 3 minutes with the specimens individually immersed in 150 ml of distilled water. Control (no disinfection) and the experimental groups (first and third disinfection cycles) were submitted to Knoop hardness measurements with indentations at the center of the labial tooth surface. Data were submitted to repeated measure two-way ANOVA and Tukey's test (α = 0.05). RESULTS: Biocler, Magister, and Trilux showed lower surface microhardness when submitted to microwave. Lower microhardness for Biotone was promoted by hypochlorite, while no significant difference was shown for New Ace. The third disinfection cycle significantly decreased the tooth surface hardness only for microwave. CONCLUSIONS: Different disinfection methods promoted different effects on the microhardness of different types of artificial teeth. Surface microhardness of the teeth was less affected by the simulated chemical disinfections when compared to microwaved specimens.

Microwave irradiation as an alternative method for disinfection of denture base acrylic resins.

AIM: This study evaluated the effect of microwave irradiation as an alternative method for disinfection of different types of denture base acrylic resins. METHODS: Twenty-four samples for each conventional, microwaved and characterized heat-cured acrylic resin were made and subjected to sterilization with ethylene oxide for the groups: 1) irradiated samples; 2) non-irradiated samples; and 3) samples without yeast. Each group was subdivided according to inoculation with C. albicans, C. dubliniensis and C. tropicalis. The samples were inoculated with 100 µL of inoculum of each species of Candida and later placed in an incubator at 37 °C for 1 hr to perform the first adhesion. After this time, each well was supplemented with sterile media and the plate was once again taken to a stove for incubation at 37 °C for 6 hr. The samples were immersed in 100 mL of sterile water and irradiated with microwave at 650 W for 3 min. Control samples were considered as the non-irradiated group. After incubation for 48 hr, irradiated and non-irradiated samples were subjected to a digital colony counter. RESULTS: Control group (non-irradiated) showed microbial growth for resins and the means of ufc/mL were without statistically significant differences. Microwave irradiated samples (experimental group) promoted no viable colonies for all Candida species and types of acrylic resins. The means of ufc/mL were without statistically significant differences. CONCLUSION: Microwave irradiation was an effective method for disinfection of the acrylic resins inoculated with C. albicans, C. dubliniensis and C. tropicalis.

Heterogeneous fenton degradation of azo dyes catalyzed by modified polyacrylonitrile fiber fe complexes: QSPR (quantitative structure peorperty relationship) study.

The amidoximated polyacrylonitrile (PAN) fiber Fe complexes were prepared and used as the heterogeneous Fenton catalysts for the degradation of 28 anionic water soluble azo dyes in water under visible irradiation. The multiple linear regression (MLR) method was employed to develop the quantitative structure property relationship (QSPR) model equations for the decoloration and mineralization of azo dyes. Moreover, the predictive ability of the QSPR model equations was assessed using Leave-one-out (LOO) and cross-validation (CV) methods. Additionally, the effect of Fe content of catalyst and the sodium chloride in water on QSPR model equations were also investigated. The results indicated that the heterogeneous photo-Fenton degradation of the azo dyes with different structures was conducted in the presence of the amidoximated PAN fiber Fe complex. The QSPR model equations for the dye decoloration and mineralization were successfully developed using MLR technique. MW/S (molecular weight divided by the number of sulphonate groups) and NN=N (the number of azo linkage) are considered as the most important determining factor for the dye degradation and mineralization, and there is a significant negative correlation between MW/S or NN=N and degradation percentage or total organic carbon (TOC) removal. Moreover, LOO and CV analysis suggested that the obtained QSPR model equations have the better prediction ability. The variation in Fe content of catalyst and the addition of sodium chloride did not alter the nature of the QSPR model equations.

Scanning electron microscopy and roughness study of dental composite degradation.

Our aim was to test the hypothesis that the use of mouthwashes, consumption of soft drinks, as well as the type of light curing unit (LCU), would change the surface roughness (Ra) and morphology of a nanofilled composite resin (Z350® 3M ESPE). Samples (80) were divided into eight groups: Halogen LCU, group 1, saliva (control); group 2, Pepsi Twist®; group 3, Listerine®; group 4, Colgate Plax®; LED LCU, group 5, saliva; group 6, Pepsi Twist®; group 7, Listerine®; group 8, Colgate Plax®. Ra values were measured at baseline, and after 7 and 14 days. One specimen of each group was prepared for scanning electron microscopy analysis after 14 days. The data were subjected to multifactor analysis of variance at a 95% confidence followed by Tukey's honestly significant difference post-hoc test. All the treatments resulted in morphological changes in composite resin surface, and the most significant change was in Pepsi Twist® groups. The samples of G6 had the greatest increase in Ra. The immersion of nanofilled resin in mouthwashes with alcohol and soft drink increases the surface roughness. Polymerization by halogen LCU (reduced light intensity) associated with alcohol contained mouthwash resulted in significant roughness on the composite.

Effect of thermocycling on the bond strength of composite resin to bur and laser treated composite resin.

The objective of this study was to investigate the effect of two different surface treatments (Er:YAG laser and bur) and three different numbers of thermal cycling (no aging, 1,000, 5,000, and 10,000 cycles) on the micro-shear bond strength of repaired composite resin. Ninety-six composite blocks (4 mm × 4 mm × 1 mm) obtained with a micromatrix hybrid composite were prepared. The composite blocks were then randomly divided into four groups (n = 24), according to the thermal cycling procedure: (1) stored in distilled water at 37°C for 24 h (control group), (2) 1,000 cycles, (3) 5,000 cycles, and (4) 10,000 cycles. After aging, the blocks were further subdivided into two subgroups (n = 12), according to surface treatment. Bur and laser-treated composite surfaces were treated with an etch&rinse adhesive system. In addition, a microhybrid composite resin was bonded to the surfaces via polyethylene tubing. Specimens were subjected to micro-shear bond strength test by a universal testing machine with a crosshead speed of 0 and 5 mm/min. The data were analyzed using one-way analysis of variance and Tukey tests (α = 0.05) for micro-shear bond strengths. After conducting a bond strength test, it was found that the laser and bur-treated specimens had similar results. Aging with 10,000 thermocycles significantly affected the repair bond strength of composite resins.

The effect of an Er,Cr:YSGG laser on the micro-shear bond strength of composite to the enamel and dentin of human permanent teeth.

The bond strength of resin composite to Er,Cr:YSGG laser-irradiated enamel and dentin has been evaluated in only a few studies. Therefore, we measured and compared the micro-shear bond strength of composite restorations to enamel and dentin using two different cavity-preparation tools and conditioning methods. One hundred and seventy-five caries-free human third molars were sectioned longitudinally into two different thicknesses and randomly assigned to seven subgroups (n = 25). Enamel groups included laser-cut without etching (LO), laser-cut and laser-etched (LL), laser-cut and acid-etched (LA), bur-cut and laser-etched (BL1), and bur-cut and acid-etched (BA1-comparison group). Dentinal groups included bur-cut and laser-etched (BL2) and bur-cut and acid-etched (BA2-comparison group). The specimens were bonded by Single Bond and Tygon tubes and were restored with Z100 composite. Failure patterns were evaluated using a stereomicroscope, and a shear bond test was performed at 0.5 mm/min. The mean shear bond strength values (MPa) for the LO, LL, LA, BL1 and BA1 enamel groups were 23.14, 23.77, 23.51, 19.30, and 28.99, respectively, whereas for the BL and BA dentinal groups, these values were 22.44 and 26.15, respectively. In enamel specimens, BA1 and LL groups presented the highest shear bond strength values, and the bur-cut and laser-etched (BL1) group showed the lowest values. In the laser-etched groups, bond strength values for bur-cut surfaces were significantly higher than those for laser-cut surfaces. Moreover, there was a significant difference between the BL2 and BA2 dentinal groups. The results of this study indicate that re-etching with acid phosphoric would be recommended if an Er,Cr:YSGG laser is used for tooth preparation or surface treatment.