Statistical process control of manufacturing tablets for antiretroviral therapy

Abstract In this study, the manufacturing process of lamivudine (3TC) and zidovudine (AZT) tablets (150+300 mg respectively) was evaluated using statistical process control (SPC) tools. These medicines are manufactured by the Fundação para o Remédio Popular "Chopin Tavares de Lima" (FURP) laboratory, and are distributed free of charge to patients infected with HIV by the Ministry of Health DST/AIDS national program. Data of 529 batches manufactured from 2012 to 2015 were collected. The critical quality attributes of weight variation, uniformity of dosage units, and dissolution were evaluated. Process stability was assessed using control charts, and the capability indices Cp, Cpk, Pp, and Ppk (process capability; process capability adjusted for non-centered distribution; potential or global capability of the process; and potential process capability adjusted for non-centered distribution, respectively) were evaluated. 3TC dissolution data from 2013 revealed a non-centered process and lack of consistency compared to the other years, showing Cpk and Ppk lower than 1.0 and the chance of failure of 2,483 in 1,000,000 tablets. Dissolution data from 2015 showed process improvement, revealed by Cpk and Ppk equal to 2.19 and 1.99, respectively. Overall, the control charts and capability indices showed the variability of the process and special causes. Additionally, it was possible to point out the opportunities for process changes, which are fundamental for understanding and supporting a continuous improvement environment.

Development of microparticles and microparticulated tablets containing piperine

Abstract Piper nigrum (black pepper) is used in Indian traditional medicine and its main alkaloid, Piperine (PIP), presents antioxidant, antitumor and neuroprotective pharmacological properties. This substance is insoluble in aqueous media and can irritate the gastrointestinal tract. Aiming to avoid these inconvenient characteristics and enable PIP oral administration, this study suggested the PIP microencapsulation through the emulsion-solvent evaporation method and the preparation of microparticulated tablets by direct compression. An UV-spectroscopy method was validated to quantify PIP. Microparticles and microparticulated tablets were successfully obtained and the microparticles exhibited excellent flow. The scanning electron microscopy images showed that PIP microparticles were intact after compression. The in vitro release showed a controlled release of PIP from microparticles and PIP microparticles from tablets in comparison to PIP and PIP tablets. The release profiles of PIP microparticles and the microparticulated tablets were similar. Therefore, tablets containing PIP microparticles are promising multiparticulated dosage forms because a tablet allows microparticles administration and the intact ones promote a controlled release, decreasing its irritating potential on the mucosa.

Interchangeability of medications and biopharmaceutical implication of taking drugs with fluids other than water: ibuprofen case study

Abstract The aim of this study was to compare the dissolution properties of ibuprofen solid oral dosage forms commercially available in Bosnia and Herzegovina and to estimate the influence of dissolution medium composition on the drug release. Eight products (A-H) were subjected to in vitro dissolution test using experimental conditions described in USP42-NF37. Dissolution properties of one selected product were examined in the presence of alcohol (22.2% v/v) and fruit juice (22.2% v/v). Products marked B-H complied with the pharmacopeial criteria. Dissolution profile of product B was similar with dissolution profiles of products D, E, F and G and similarity was also found between products A-D, C-G, D-G and E-F. Drug release from most of the examined preparations fitted best to the Weibull kinetic model. In the presence of alcohol in the medium, higher amount of ibuprofen was dissolved. Contrary, ibuprofen dissolved in the presence of fruit juice was significantly lower. Differences in the dissolution profiles of investigated preparations suggest that their interchangeability should be additionally considered and demonstrated with in vivo bioequivalence studies. Presence of different substances in the medium can affect dissolution properties of ibuprofen, emphasizing the importance of the patient's compliance.

Stability of sulfadiazine sugar-free oral suspensions for the treatment of congenital toxoplasmosis

Abstract This study aimed to develop and evaluate the stability of sulfadiazine sugar-free extemporaneous oral suspensions, focusing on treating congenital toxoplasmosis. The excipients were carefully chosen to obtain safe products for the pediatric population. Sulfadiazine suspensions (100 mg/ mL) were prepared from the raw material or tablets, stored in amber glass bottles at 5±3ºC, and evaluated at 0, 14, and 30 days. An ultra-performance liquid chromatographic method was developed and validated to assay the drug. The particle size ranged from 29.3 to 50.6 µm, with some variation over the study; pH values around 7.0 and non-Newtonian behavior were observed without modification in the period. Formulations showed a fast dissolution rate (>80% in 15 minutes) without variation over the study. The drug assay was about 100% of the label claimed throughout the study, demonstrating the chemical stability and the preparations' dose homogeneity. The microbiological investigation indicated that both preparations met the requirements for the microbial count and absence of pathogens. In conclusion, the developed formulations can be used for 30 days when stored under refrigeration. The oral suspensions produced are easy to prepare and contain safe components, providing an alternative for congenital toxoplasmosis treatment in children

Perfil de medicamentos descartados nas farmácias públicas de um município do leste de Minas Gerais / Profile of medicines discarded in the public pharmacies of an eastern municipality of Minas Gerais

O descarte inadequado de medicamentos pode levar a impactos ambientais negativos e deve ser considerado um problema de saúde pública. O presente estudo teve como objetivo levantar dados quantitativos e qualitativos relacionados ao perfil dos medicamentos descartados no município de Governador Valadares - MG. O trabalho foi desenvolvido nas UAPS/ESF que possuíam farmácias, e também na Farmácia Central/Policlínica Municipal. Nesses locais, foi realizada uma análise dos medicamentos descartados no período de julho de 2017 a maio de 2018. Por meio dos dados obtidos nesse período foi possível perceber que as principais classes de medicamentos descartadas foram os inibidores da enzima conversora de angiotensina, antagonistas da angiotensina II, agentes betabloqueadores, diuréticos, hipoglicemiantes, contraceptivos hormonais e agentes modificadores de lipídeos. Além disso, foi realizada uma ação de educação em saúde e aplicado um questionário semiestruturado aos usuários participantes dos grupos operativos. Dos 34 usuários respondentes do questionário, 23 (69,70%) não tinham acesso a informação sobre o local correto de descarte e armazenamento de medicamentos. Após a ação de educação em saúde verificou-se um aumento no quantitativo de medicamentos descartados pelos usuários nas UAPS/ESF Mãe de Deus I e II, Altinópolis III e IV, Santa Rita II, São Pedro I e II e Esperança e Nossa Senhora das Graças. O trabalho desenvolvido permitiu apresentar dados relevantes para a gestão municipal demonstrando a importância do farmacêutico no cuidado em saúde e o caráter epidemiológico local da prevalência das doenças crônico não transmissíveis.

The inadequate disposal of drugs can lead to negative environmental impacts and should be treated as a public health problem. This study aimed at surveying quantitative and qualitative data related to the profile of drugs discarded in the city of Governador Valadares - MG. The work was developed in the UAPS / ESF that had pharmacies, and also in the Central Pharmacy/Municipal Polyclinic. In these locations, an analysis of the drugs discarded between July 2017 and May 2018 was carried out. Through the data obtained in this period, it was possible to notice that the main classes of drugs discarded were angiotensin-converting enzyme inhibitors, angiotensin II antagonists, beta-blocking agents, diuretics, hypoglycemic agents, hormonal contraceptives, and lipid-modifying agents. In addition, a health education action was carried out and a semi-structured questionnaire was applied to users participating in the operating groups. From the 34 users who responded the questionnaire, 23 (69.70%) did not have access to information on the correct place to dispose and store medicines. After the health education action, there was an increase in the amount of drugs discarded by users in the UAPS/ESF Mãe de Deus I and II, Altinópolis III and IV, Santa Rita II, São Pedro I and II, and Esperança and Nossa Senhora das Graças. The work carried out made it possible to present relevant data for municipal management, demonstrating the importance of the pharmacist in health care and the local epidemiological character of the prevalence of chronic non-communicable diseases.

Optimization of Diltiazem hydrochloride osmotic formulation using QBD approach

Abstract Diltiazem hydrochloride (DLH) is a calcium channel blocker useful for the treatment of angina pectoris, arrhythmia, and hypertension. DLH having a short half-life needs frequent administration for successful treatment but this poses a problem of poor patient compliance. These requirements are served by elementary osmotic pump tablets (EOP) based controlled-release (CR) systems. Quality by design (QbD) approach assists in screening various factors with subsequent assessment of critical parameters that can have a major impact on the scalability of EOP. Tablets were formulated using wet granulation method followed by osmotic coating. Factorial design based QbD strategy aided in defining the risk assessment of influential variables such as hydrophilic polymers and osmotic coat component on the in-vitro release kinetics of the designed EOP tablets. These formulated EOP systems followed zero-order kinetics, a characteristic feature of EOPs. EOP tablets were formulated applying a systematic QbD statistical approach. The formulated DLH EOP systems with improved concentration-independent behavior helped to address the challenges of IR formulation. Application of QbD strategy in ascertaining the scalability of DLH EOP formulation would help pharmaceutical industries in the translation of EOP based drug delivery systems from R&D to market.

Intra and Extra-granular Disintegrant Properties of Modified Underutilised Red Lima Bean Starch in Paracetamol Tablet Formulation

Abstract Red lima bean (Phaseolus lunatus Linn) Family Fabaceae, has been modified by succinylation and annealing, and used as intra- and extra-granular disintegrants at concentrations of 5 and 10 %w/w in paracetamol tablet formulation in comparison with corn starch BP. The starches were characterised using FT-IR spectroscopy, SEM, proximate analysis, physicochemical and functional properties. FT-IR spectrometry revealed characteristic peaks at 1575.53 and 1713.99 cm-1 for the succinylated starch while the annealed showed no significant difference from the native starch. Modifications did not alter the ovoid shape of the native starch but reduced the particle size. Succinylation improved water absorption capacity, solubility and swelling of lima bean starch but annealing reduced the parameters. Tablets with disintegrants of lima bean starches generally had higher crushing strengths and lower friability than tablets with corn starch. Modifications reduced the disintegration time of the tablets when the starches were incorporated intra-granularly, which suggested particle-particle bond interruption and destruction of hydrogen bonds as mechanism of disintegration. Tablets containing 10 %w/w succinylated red lima bean starch incorporated intra-granularly had the highest disintegration efficiency ratio, DER, indicating a great balance between mechanical and disintegration properties. Modified red lima bean starches incorporated intra-granularly into paracetamol tablets led to faster disintegration and could efficiently substitute corn starch as disintegrant.

Quality control and drug-drug interactions between commercially available Metoprolol and Glimepiride tablets

Abstract Quality is paramount and needs to be maintained throughout the shelf life of pharmaceuticals. The current study aimed to evaluate the quality, potency, and drug-drug interaction in an in vivo animal model by using two drugs, namely, metoprolol and glimepiride. Tablets were selected for their physical characteristics, such as shape, size, and color. Quality control tests, such as weight variation, hardness, friability, and disintegration tests, and invitro drug release studies were performed as per USP. Drug-drug interaction and in vivo studies were carried out according to the standard protocol of the animal ethics committee. Quality control tests of both the tablets were within the specified range. The cumulative release percentages of the drugs were 81.12% and 85.36% for Metoprolol Tartrate and Glimepiride, respectively, in a physiological buffer solution within 1 h. The combination of metoprolol and Glimepiride also significantly decreased the blood glucose level in diabetic animals. However, the blood glucose level increased in the group receiving metoprolol only, but the difference was not significant. The result suggested that the formulations are safe. However, the chronic use of this combination requires frequent monitoring of blood glucose level to improve its efficacy and for the patient's safety.

Optimization and Quest of HPMC loaded Stavudine Controlled Release Dosage Development by Central Composite Design utilizing Reduced Factorial Screening Technique

Abstract The current research focused on screening and finding the significant independent variables in stavudine loaded tablet, followed by optimizing the best formulation using central composite design. The objective of the study to develop stavudine loaded controlled release tablet utilizing reduced factorial design, followed by optimization technique as well as characterization of prepared tablets. Preliminary trial batches were prepared using different grades of hydroxypropyl methylcellulose. The resolution-IV reduced factorial design was selected to screen the significant independent variables in the dosage form design. A total number of eight runs were prepared and responses were recorded. The signified factors identified by half-normal and Pareto chart. The prepared tablets are evaluated for various physiochemical characterizations. Three dependent responses such as hardness, dissolution at 6 hour and 12 hours are considered in optimization process. Later on, drug-polymer interaction study was carried out. The principal of the study design based on finding the best formulation with prefixed set parameter values utilizing the concept of screening technique. It observed that HPMC K15M (57.18 %), HPMC K100 (66.32 %) and PVP K30 (7.97 %) as best composition in a formulation batch would fulfill the predetermined parameter with specific values.

Formulation, Optimization, in vitro and in-vivo evaluation of levofloxacin hemihydrate Floating Tablets

Abstract The objective of the present investigation was to design, optimize and characterize the gastro retentive floating levofloxacin tablets and perform in-vivo evaluation using radiographic imaging. The floating tablets were prepared by using polymers i.e hydroxy propyl methyl cellulose (HPMC-K4M) and carbopol-940 individually and in combination by nonaquous granulation method. All the Formulations were evaluated for swelling index (S.I), floating behavior and in-vitro drug release kinetics. The compatibility study of levofloxacin with other polymers was investigated by FTIR, DSC, TGA and XRD. Results from FTIR and DSC revealed no chemical interaction amongst the formulation components. The optimized formulation (F11) showed floating lag time (FLT), total floating time (TFT) swelling index (S.I) of 60 sec, >16h and approximately 75 %, respectively. Moreover, F11 showed zero order levofloxacin release in simulated gastric fluid over the period of 6 h. X-ray studies showed that total buoyancy time was able to delay the gastric emptying of levofloxacin floating tablets in rabbits for more than 4 hours. In conclusion the optimized formulation (F11) can be used for the sustained delivery of levofloxacin for the treatment of peptic ulcer.

Optimization of HPLC method using central composite design for estimation of Torsemide and Eplerenone in tablet dosage form

Abstract A simple, precise, accurate and robust high performance liquid chromatographic method has been developed for simultaneous estimation of Torsemide and Eplerenone in tablet dosage form. Design of experiment was applied for multivariate optimization of the experimental conditions of RP-HPLC method. A Central composite design was used to study the response surface methodology and to analyse in detail the effects of these independent factors on responses. Total eleven experiments along with 3 center points were performed. Two factors were selected to design the matrix, one factor is variation in ratio of Acetonitrile and the second factor is flow rate (mL/min). Optimization in chromatographic conditions was achieved by applying Central composite design. The optimized and predicted data from contour diagram comprised mobile phase (acetonitrile, water and methanol in the ratio of 50: 30: 20 v/v/v respectively), at a flow rate of 1.0 ml/min and at ambient column temperature. Using these optimum conditions baseline separation of both drugs with good resolution and run time of less than 5 minutes were achieved. The optimized assay conditions were validated as per the ICH guidelines (2005). Hence, the results showed that the Quality by design approach could successfully optimize RP-HPLC method for simultaneous estimation of Torsemide and Eplerenone.

Sustained release matrix tablet of 100 mg losartan potassium: Formulation development and in vitro characterization

Abstract Sustained release matrix tablets of 100 mg losartan potassium HCl were fabricated with two release retarding polymers namely HPMC K100 M and affinisol by direct compression method. Nine trial formulations were prepared by varying content of these polymers, each from 50 mg to 100 mg; keeping the total weight of the tablet 310 mg. The best formulation was selected based on in vitro drug release profile for 12 hours conducted in Type II dissolution apparatus at 50 rpm and water as dissolution medium. Pre-compression parameters such as bulk density, tap density, Carr's index and Hausner ratio were evaluated for the selected tablet. The tablets were subjected to thickness, weight variation test, drug content, hardness and friability. Drug release kinetics, surface morphology and accelerated stability study were investigated for that selected formulation. Formulation F4 with the composition of 75 mg HPMC K100M and 100 mg affinisol was selected as the best formulation that extended the drug release up to 12 hours. Pre-compression parameters and other tableting properties were within the Pharmacopoeia limit. Release kinetics analysis proved non-fickian zero-order drug release and that was further confirmed by surface morphology of the tablets before and after dissolution study visualized by SEM. The developed formulation was found to be stable for one month stored at 60 ○C.

Pharmaceutical evaluation of compounded furosemide capsules and excipient performance

Abstract Compounding pharmacies play an important role not only in compounding personalized formulations, but also preparing drugs at the same concentration and dosage as those from commercial manufacturers. The excipients used in compounding are generally standardized for many drugs, however they do not consider the intrinsic properties, such as the poor water solubility, of each substance. The excipient performance of commercially available compounded furosemide capsules in 7 compounding pharmacies from Manaus was evaluated and compared them to the performance of the reference medicinal product (Lasix® tablets) and 2 batches of capsules made in-house (T2 and T4) with a standardized excipient. All batches were subjected to tests for weight variation, assay, uniformity of dosage units, disintegration and dissolution profile. Of the 7 different compound formulas acquired in the compounding pharmacies, only 2 passed all tests. Most formulas passed the tests for weight determination, disintegration time and assay, however batches from 2 establishments failed in regards to the uniformity of the content and 5 batches failed the dissolution test. The reference medicinal product was approved in all tests, as were the T2 capsules made in-house with drug-excipient ratio 1:2. These results confirm the importance of the excipient composition, especially for poorly soluble drugs.

Evaluation of physicochemical and microbiological stability of liquid preparation from tizanidine hydrochloride tablets - a Hospital concern

Tizanidine hydrochloride is a centrally acting skeletal muscle relaxant, used in the management of spasticity. This drug is commercially available only as tablets, which highlights the need to develop oral liquid formulations. In the hospital environment, this aspect is circumvented by the preparation of suspensions, to allow administration to children and adults with impaired swallowing, but there are no data regarding their stability. The purpose of this study was to evaluate the physicochemical andmicrobiological stability of liquid dosage forms prepared in the hospital environment from tizanidine hydrochloride tablets, applying high performance liquid chromatography (HPLC) and microbiological analysis. A simple and stability-indicating HPLC method was developed and validated for specificity, linearity, limits of detection and quantification, precision, accuracy and robustness. The liquid formulations were placed in amber PET and glass bottles, which were stored under three different conditions: at room temperature, under refrigeration and at 40 ºC. The liquid formulations were analyzed and demonstrated chemical stability for 56 days, allowing their use for long periods. However, the determination of microbiological stability showed that these formulations are prone to microbial contamination, which has dramatically reduced its stability to 7 days, in both bottles and at all evaluated temperatures

Efecto de gas de formalina sobre el recuento de mesófilos en nailon comercial destinado a procedimientos quirúrgicos / Effect of formaline gas on the counting of mesophiles in commercial nylon destined to surgical procedures

RESUMEN La investigación se realizó a fin de evaluar el efecto del gas de formalina sobre el recuento de mesófilos en nailon comercial (poliamida) destinado a procedimientos quirúrgicos. En primer lugar, se evaluó la contaminación de una muestra del material comercial de 1 g expuesta al ambiente de quirófano por 72 horas, a través de la técnica de recuento en placa para mesófilos; se obtuvieron 850 UFC/g. Una vez comprobada la contaminación de la poliamida comercial, esta se sometió a gases de formalina en comprimidos. Se colocaron 5 muestras (n=5) de nailon de 1 g cada una en 5 recipientes herméticos de 1 litro con 1 gramo de formalina cada uno; estos recipientes se almacenaron en un mueble en sala de esterilización a un metro de altura del piso y posteriormente, fueron abiertos y cultivados a través de la técnica de recuento en placa para mesófilos, uno por día a lo largo de 5 días a intervalos de 24 horas. Los resultados obtenidos no registraron crecimientos de microorganismos a partir de las 24 horas y durante los 5 días posteriores y se encontraron diferencias estadísticamente significativas (p < 0,05). Se concluye que bajo las condiciones del presente estudio el tiempo de esterilización de la formalina sobre nailon comercial es de 24 horas.

ABSTRACT Hie present research work was carried out with the purpose of evaluating the effect of formalin gas on the count of mesophiles in commercial nylon (polyamide) destined to surgical procedures. Firstly, the contamination of a 1 g commercial nylon sample, exposed to the operating room environment for 72 hours, was evaluated through the plate counting technique for mesophiles; it yielded a result of 850 CFU / gram. Once the contamination of the commercial polyamide was checked, it was subjected to formalin gases in tablets. Five nylon samples (n=5) of 1 gram each were placed in 5 1 liter airtight containers containing 1 gram of formalin; Hese containers were stored in a cabinet in the sterilization room one meter above the floor, and later opened and cultivated through the plate counting technique for mesophiles, one per day for 5 days at 24 hour intervals. The results obtained after being exposed to formalin gases in tablets did not register growths of microorganisms after 24 hours and during the 5 days after the study, finding statistically significant differences (p < 0.05) in relation to the studied times concluding under the conditions of the present study that the sterilization time of the formalin on commercial nylon is equal to 24 hours.

Beliefs related to oral antidiabetic use among individuals with diabetes / Creencias relacionadas con el uso antidiabético oral en personas con diabetes / Crenças relacionadas ao uso de antidiabético oral em pessoas com diabetes

Abstract Objective: To identify beliefs related to oral antidiabetic use among individuals with type 2 diabetes mellitus, based on the Theory of Planned Behavior. Method: This is a descriptive, quantitative and qualitative study conducted with 32 participants using oral antidiabetic drugs. Data was collected through an open question tool and analyzed by number of emissions and content. Results: Among the behavioral beliefs, the following stand out: (a) as an advantage, to keep diabetes controlled; and (b) as disadvantages, gastric pain and discomfort, nausea and diarrhea. In the normative beliefs, family stood out as a social referent (children, mother and siblings). As for the control beliefs, taking the tablets with water and the size of the tablets stood out as practicalities and difficulties, respectively, in relation to the oral therapy follow-up. Conclusion and implications for practice: It was possible to identify the beliefs regarding the behavior of taking oral antidiabetics that will contribute to foster educational strategies with the potential to strengthen the positive beliefs and to revert the negative ones, in favor of adherence to drug therapy, glycemic control and quality of life.

Resumen Objetivo: Identificar las creencias relacionadas con el uso de antidiabéticos orales en personas con diabetes mellitus tipo 2, con base en la Teoría de la Conducta Planificada. Método: Estudio descriptivo, con abordaje cuantitativo y cualitativo, realizado con 32 participantes en tratamiento con antidiabéticos orales. Los datos se recolectaron por medio de un formulario con preguntas abiertas y se los analizó por la cantidad de emisiones y el contenido. Resultados: Entre las creencias comportamentales se destacan las siguientes: (a) como ventaja, mantener controlada la diabetes; y (b) como desventajas, dolor y malestar gástrico, náusea y diarrea. En las creencias normativas sobresalió la familia como referente social (hijos, madre y hermanos). En cuanto a las creencias de control, tomar los comprimidos con agua y el tamaño de los comprimidos se destacaron como facilidades y dificultades, respectivamente, en relación con el seguimiento de la terapia oral. Conclusión e implicaciones para la práctica: Fue posible identificar las creencias con respecto a la conducta en el uso de antidiabéticos orales que ayudarán a fomentar estrategias educativas con el potencial de fortalecer las creencias positivas y revertir las negativas, en beneficio de la adhesión a la terapia medicamentosa, del control de la glicemia y de la calidad de vida.

Resumo Objetivo: Identificar as crenças relacionadas ao uso de antidiabético oral em pessoas com diabetes mellitus tipo 2, com base na Theory of Planned Behavior. Método: Estudo descritivo com abordagem quantiqualitativa, realizado com 32 participantes em uso de antidiabético oral. Os dados foram coletados por meio de formulário com perguntas abertas e analisados pelo número de emissões e conteúdo. Resultados: Entre as crenças comportamentais, destacam-se: como vantagem, manter o diabetes controlado; e, como desvantagens, dor e desconforto gástrico, enjoo e diarreia. Nas crenças normativas, sobressaiu como referente social a família (filhos, mãe e irmãos). Quanto às crenças de controle, tomar os comprimidos com água e o tamanho dos comprimidos como as facilidades e dificuldades, respectivamente, em relação ao seguimento da terapêutica oral. Conclusão e implicações para prática: Foi possível identificar as crenças frente ao comportamento da tomada do antidiabético oral que contribuirão para fomentar estratégias educativas com poder de fortalecer as positivas e reverter as negativas, em benefício da adesão à terapêutica medicamentosa, ao controle glicêmico e à qualidade de vida.

Development of controlled release dexketoprofen tablets and prediction of drug release using Artificial Neural Network (ANN) modelling

Dexketoprofen trometamol (DT) is an active S (+) enantiomer of ketoprofen, and a non-steroidal anti-inflammatory agent. DT has a short biological half-life and the dosing interval is quite short when there is a need to maintain the desirable effect for longer time periods. Consequently, a controlled release DT tablet was designed for oral administration aiming to minimize the number of doses and the possible side effects. Calculations of the parameters for controlled release DT tablets were shown clearly. Controlled release matrix-type tablet formulations were prepared using hydroxypropyl methylcellulose (HPMC) (low and high viscosity), Eudragit RS and Carbopol, and the effects of different polymers on DT release from the tablet formulations were investigated. The dissolution rate profiles were compared and analyzed kinetically. An Artificial Neural Network (ANN) model was developed to predict drug release and a successful model was obtained. Subsequently, an optimum formulation was selected and evaluated in terms of its analgesic and anti-inflammatory activity. Although the developed controlled release tablets did not have an initial dose, they were found to be as effective as commercially available tablets on the market. Dissolution and in vivo studies have shown that the prepared tablets were able to release DT for longer time periods, making the tablets more effective, convenient and more tolerable.

Formulation and evaluation of a mucoadhesive buccal tablet of mefenamic acid

Buccal route of administration has many advantages such as improving patient compliance, bypassing the GIT and hepatic first pass effect. The objectives are to formulate mucoadhesive buccal tablet using Mefenamic acid and compatible excipients, and to evaluate the product using quality control tests and in vitro tests. The ingredients were subjected to Differential Scanning Calorimetry and Fourier Transform Infrared Spectroscopy studies for compatibility test and the results showed no interaction. Two batches of mefenamic buccal tablet were prepared. The tablet thickness and diameter are 3.75 mm and 12 mm respectively. All tablets are within the specification of +/- 5%. The in-house tablet hardness is 6.8-15kg and percent friabilation is not more than 0.8%. The disintegration test showed that all tablets disintegrated within 4 hours. The content uniformity showed that tablets are within the range of 85%-115%. The tablet weight is within the 5% range. The percent swelling is 53.83% to 58.86% and moisture absorption is 14.79% to 15.56%. The surface pH of the tablet is close to the salivary pH, which means that it would not irritate the buccal mucosa. The buccal tablet has a mucoadhesiveness of 0.196 to 0.200. There was no change in pH and size after subjecting it to stability studies in human saliva. Drug release studies showed 80.7% to 83.4% after 3 hours. Even after 3 months of subjecting the tablets to 40 ºC and 75% RH, results are within acceptable range. The results show the potential of the formulation as a mucoadhesive buccal tablet.

Partição de Comprimidos Antineoplásicos Utilizados no Tratamento de Leucemias Agudas em Crianças e Adolescentes / Splitting of Antineoplastic Tablets Used in Acute Leukemias Treatment in Children and Adolescents / Partición de Comprimidos Antineoplásicos Empleados en el Tratamiento de Leucemias Agudas en Niños y Adolescentes

Introdução: A manipulação de antineoplásicos para ajuste de dose, como partição de comprimidos, é comum no tratamento de leucemias agudas de crianças e adolescentes. Objetivo: Identificar a frequência e descrever a prática da partição domiciliar de comprimidos antineoplásicos utilizados no tratamento oral de crianças e adolescentes com leucemias agudas na fase de manutenção. Método: Trata-se de um estudo transversal descritivo, realizado em um hospital pertencente à rede de saúde pública do Distrito Federal com assistência especializada em pediatria. Foram incluídos no estudo crianças e adolescentes entre 1 e 18 anos, diagnosticados com leucemias agudas e em fase de manutenção do tratamento no período de estudo. Foi aplicado um questionário semiestruturado ao responsável principal pela administração dos medicamentos quimioterápicos via oral, podendo ser o cuidador ou a própria criança/adolescente. Foram coletadas variáveis sociodemográficas dos pacientes e cuidadores e variáveis sobre a prática de partição de medicamentos antineoplásicos no domicílio. Resultados: Todos os 48 entrevistados no período do estudo relataram ter partido comprimidos antineoplásicos ao longo do tratamento de leucemias agudas, sendo estes mercaptopurina (n=45 [93,75%]) e tioguanina (n=3 [6,25%]). Conclusão: A partição de comprimidos antineoplásicos foi uma prática unânime em virtude da necessidade referida de ajuste de dose individual para o tratamento de leucemias agudas de crianças e adolescentes, considerando a indisponibilidade de formulações adequadas. Os resultados reforçam a necessidade de a partição ser uniformizada e realizada de maneira a minimizar os riscos e a garantir a segurança para as crianças e adolescentes e seus cuidadores.

Introduction: Antineoplastic drug manipulation for dose adjustment, such as tablet splitting, is standard in acute leukemia treatment for children and adolescents. Objective: To identify the frequency and describe the practice of household splitting of antineoplastic tablet for oral treatment of children and adolescents with acute leukemias in the maintenance phase. Method: Cross-sectional descriptive study performed in a public health system hospital from Distrito Federal (Brazil) with specialized pediatric assistance. Children and teenagers between 1 and 18 years old, diagnosed with acute leukemia and in treatment maintenance phase during the study period were included. A semi-structured questionnaire was applied to the main responsible for administering oral chemotherapy drugs, which could be the caregiver or the child/adolescent themselves. Sociodemographic variables of patients and caregivers and variables on the practice of splitting antineoplastic drugs at home were collected. Results: All 48 interviewees in the study period reported having split antineoplastic tablets during the treatment for acute leukemias, such as mercaptopurine (n = 45 [93.75%]) and thioguanine (n = 3 [6.25%]). Conclusion: The splitting of antineoplastic tablets was a unanimous practice due to the reported need to adjust the individual dose for acute leukemia treatment in children and adolescents, considering the unavailability of adequate formulations. The results reinforce the need for splitting to be standardized and performed in a way that minimizes risks and ensures safety for patients and their caregivers

Introducción: La manipulación de fármacos antineoplásicos para el ajuste de dosis, como las particiones de comprimidos, es frecuente en el tratamiento de las leucemias agudas en niños y jóvenes. Objetivo: Identificar la frecuencia y describir la práctica de la división domiciliaria de medicamentos antineoplásicos utilizados en el tratamiento oral de niños y adolescentes con leucemias agudas en la fase de mantenimiento. Método: Se trata de un estudio transversal descriptivo realizado en un hospital de la red de salud pública del Distrito Federal (Brasil) con asistencia especializada en pediatría. El estudio incluyó a niños y jóvenes de entre 1 y 18 años de edad diagnosticados con leucemia aguda y en fase de mantenimiento del tratamiento en el período del estudio. Se aplicó un cuestionario semiestructurado a la persona principal responsable de la administración de fármacos quimioterapéuticos por vía oral, que puede ser el cuidador o el propio niño/joven. Fueron colectadas variables sociodemográficas de los pacientes y cuidadores y variables sobre la práctica de la división de los medicamentos antineoplásicos en domicílios. Resultados: Los 48 entrevistados en el período de estudio informaron haber roto las pastillas antineoplásicas durante el tratamiento de la leucemia aguda, siendo éstas mercaptopurina (n=45 [93,75%]) y tioguanina (n=3 [6,25%]). Conclusión: La partición de comprimidos antineoplásicos fue una práctica unánime debido a la necesidad mencionada de ajustar la dosis individual para el tratamiento de las leucemias agudas de niños y adolescentes, considerando la falta de formulaciones apropiadas. Los resultados refuerzan la necesidad de estandarizar y realizar la partición para minimizar los riesgos y garantizar la seguridad de los niños, jóvenes y sus cuidadores.

Evaluación de la Calidad vs precio de comprimidos de Metformina de 850mg de producción nacional e importados, comercializados en Paraguay utilizados para el control de diabetes / Quality vs. price evaluation of national and imported 850 mg metformin tablets marketed for the control of diabetes in Paraguay

La metformina es un fármaco de primera elección, solo o combinado, en el tratamiento inicial de pacientes con diabetes tipo 2, cuya prevalencia a nivel nacional es de 8,0% en hombres y 8,3% en mujeres, con un gasto anual de 283 USD/persona. El estudio fue realizado con el objetivo de evaluar la calidad fisicoquímica y precio de comprimidos de 850 mg de metformina comercializados en nuestro país. Se analizaron medicamentos de producción nacional e importada, conteniendo 850 mg de metformina HCl, tomando como referencia la Farmacopea de los Estados Unidos (USP 38). Para evaluar la calidad de los productos se realizaron ensayos físicos químicos, además de los perfiles de disolución según el medio propuesto por la USP 38. Los resultados obtenidos se encontraron dentro de las especificaciones de valoración, entre 96% y 101% de metformina y los perfiles de disolución entre 70% y 90% de la cantidad declarada en 20 minutos, con una eficiencia de disolución (EF) entre 58% y 93%, mostrando que no existe diferencia estadísticamente significativa (p=0,41). La variación de precios encontrados fue entre 3,6 USD y 8,4 USD. Los productos analizados pueden ser intercambiables en cuanto a la calidad y los perfiles de disolución in vitro, siendo una herramienta para demostrar intercambiabilidad de productos farmacéuticos, buscando el precio más accesible en el mercado nacional y facilitando el tratamiento adecuado sobre todo para la población de escasos recursos manteniendo la calidad y eficacia del mismo(AU)