RESUMEN
The addition of nanoparticles has been presented as an alternative approach to counteract the degradation of polymeric solutions for enhanced oil recovery. In this context, a nanohybrid (NH34) of partially hydrolyzed polyacrylamide (MW â¼12 MDa) and nanosilica modified with 2% 3-aminopropyltriethoxysilane (nSiO2-APTES) was synthesized and evaluated. NH34 was characterized by using dynamic light scattering, Fourier-transform infrared spectroscopy, and thermogravimetric analysis. Fluid-fluid tests assessed its viscosifying power, mechanical stability, filterability, and emulsion behavior. Rock-fluid tests were carried out to determine the nanohybrid's adsorption in porous media, the inaccessible pore volume (IPV), and the resistance (RF) and residual resistance factors (RRF). These tests were conducted under the conditions of a Colombian field. NH34 results were compared with four (4) commercial polymers (P34, P88, P51, and PA2). The viscosifying power of NH34 was observed to be similar to that of the four commercial polymers at a lower concentration, but it exhibits more resistance to mechanical and chemical degradation. The evaluation of the emulsion behavior showed that the nanohybrid neither changed the dehydration process nor altered the crude oil viscosity, favoring its extraction at the wellhead. However, the water clarification treatment must be adjusted because the oil and grease contents and turbidity increase with the residual concentration of NH34. Incremental oil recovery factors obtained by numerical simulation (compared to waterflooding) were P51 (5.5%) > P34 (4.9%) > P88 (4.8%) > NH34 (2.6%) > PA2 (0.9%). The polymers P51, P34, and P88 had a better recovery factor than NH34 and PA2 due to their lower values of residual adsorption and IPV. Few studies have been reported on polymer nanohybrids' emulsion and flow behavior. Therefore, further research is needed to enhance our understanding of the fundamental enhanced oil recovery mechanisms associated with polymer nanohybrids.
RESUMEN
Biopolymers emerge as promising candidates for enhanced oil recovery (EOR) applications due to their molecular structures, which exhibit better stability than polyacrylamides under harsh conditions. Nonetheless, biopolymers are susceptible to oxidation and biological degradation. Biopolymers reinforced with nanoparticles could be a potential solution to the issue. The nanofluids' stability and performance depend on the nanoparticles' properties and the preparation method. The primary objective of this study was to evaluate the effect of the preparation method and the nanoparticle type (SiO2, Al2O3, and TiO2) on the viscosity and stability of the scleroglucan (SG). The thickening effect of the SG solution was improved by adding all NPs due to the formation of three-dimensional structures between the NPs and the SG chains. The stability test showed that the SG + Al2O3 and SG + TiO2 nanofluids are highly unstable, but the SG + SiO2 nanofluids are highly stable (regardless of the preparation method). According to the ANOVA results, the preparation method and standing time influence the nanofluid viscosity with a statistical significance of 95%. On the contrary, the heating temperature and NP type are insignificant. Finally, the nanofluid with the best performance was 1000 ppm of SG + 100 ppm of SiO2_120 NPs prepared by method II.
RESUMEN
As oil fields go into their final stage of production, new technologies are necessary to sustain production and increase the recovery of the hydrocarbon. Chemical injection is an enhanced recovery technique, which focuses on increasing the effectiveness of waterfloods. However, the use of chemical flooding has been hampered by its relatively high cost and the adsorption of the injected chemicals onto the reservoir rocks. In recent years, nanofluids have been launched as an overall less expensive and more efficient alternative to other chemical agents. Nanoparticle inclusion is also proposed to mitigate polymer flooding performance limitations under harsh reservoir conditions. This review presents a comprehensive discussion of the most recent developments of polymer nanohybrids for oil recovery. First, the preparation methods of polymer nanohybrids are summarized and explained. Then, an explanation of the different mechanisms leading to improved oil recovery are highlighted. Finally, the current challenges and opportunities for future development and application of polymer nanohybrids for chemical flooding are identified.
RESUMEN
Recent studies revealed higher polymer flooding performance upon adding metal oxide nanoparticles (NPs) to acrylamide-based polymers during heavy oil recovery. The current study considers the effect of TiO2, Al2O3, in-situ prepared Fe(OH)3 and surface-modified SiO2 NPs on the performance of xanthan gum (XG) solutions to enhance heavy oil recovery. Surface modification of the SiO2 NPs was achieved by chemical grafting with 3-(methacryloyloxy)propyl]trimethoxysilane (MPS) and octyltriethoxysilane (OTES). The nanopolymer sols were characterized by their rheological properties and ζ-potential measurements. The efficiency of the nanopolymer sols in displacing oil was assessed using a linear sand-pack at 25 °C and two salinities (0.3 wt % and 1.0 wt % NaCl). The ζ-potential measurements showed that the NP dispersions in deionized (DI) water are unstable, but their colloidal stability improved in presence of XG. The addition of unmodified and modified SiO2 NPs increased the viscosity of the XG solution at all salinities. However, the high XG adsorption onto the surface of Fe(OH)3, Al2O3, and TiO2 NPs reduced the viscosity of the XG solution. Also, the NPs increased the cumulative oil recovery between 3% and 9%, and between 1% and 5% at 0 wt % and 0.3 wt % NaCl, respectively. At 1.0 wt % NaCl, the NPs reduced oil recovery by XG solution between 5% and 12%, except for Fe(OH)3 and TiO2 NPs. These NPs increased the oil recovery between 2% and 3% by virtue of reduced polymer adsorption caused by the alkalinity of the Fe(OH)3 and TiO2 nanopolymer sols.