Orientation of the acetabular component. A comparison of five navigation systems with conventional surgical technique.

We compared the orientation of the acetabular component obtained by a conventional manual technique with that using five different navigation systems. Three surgeons carried out five implantations of an acetabular component with each navigation system, as well as manually, using an anatomical model. The orientation of the acetabular component, including inclination and anteversion, and its position was determined using a co-ordinate measuring machine. The variation of the orientation of the acetabular component was higher in the conventional group compared with the navigated group. One experienced surgeon took significantly less time for the procedure. However, his placement of the component was no better than that of the less experienced surgeons. Significantly better inclination and anteversion (p < 0.001 for both) were obtained using navigation. These parameters were not significantly different between the surgeons when using the conventional technique (p = 0.966). The use of computer navigation helps a surgeon to orientate the acetabular component with less variation regarding inclination and anteversion.

[Comparison of total hip replacements cup orientation and position. Navigation vs. conventional manual implantation of hip prostheses]. / Pfannenposition und Orientierung im Vergleich. Navigation vs. konventionelle Handimplantion von Hüftendoprothesen.

BACKGROUND: Aim of this in-vitro study was to compare the hip cup placement for total hip replacement when using different navigation systems compared with the traditional, non-navigated technique. METHODS: Five different navigation systems were used: the CT-less systems Navitrack, Orthopilot and Surgetics Station, as well as the CT-based Navitrack and VectorVision. Three different surgeons carried out five cup implantations using all navigation systems and the manual approach on a surgery dummy. Cup orientation (inclination and anteversion) and the cup position (achieved cup center) were determined with a coordinate measuring machine. RESULTS: In the manual group the variability of the cup orientation was higher in comparison and hardly influenced by the surgeon. Navigation was identified as a significant factor for smaller deviations from planned inclination and anteversion angles (p<0,001 for both). Cup position was not affected by surgeon in the manual group (p=0,966). Compared with manual technique, the cup misplacement vector was significantly smaller in the CT-Navitrack group (p<0,001) but higher in the Navitrack (CT-less) and VectorVision group (p<0,001). CONCLUSIONS: The use of computer navigation will help the surgeon to orientate the acetabular component more accurately but not necessarily with regard to cup positioning.

[Temperature measurements during abrasive water jet osteotomy]. / Wärmeentwicklung bei der Wasser-Abrasivstrahl-Osteotomie.

Working on bone is a major aspect of orthopaedic surgery. Despite its well-known appreciable thermal effects on the edges of the bone cut, the oscillating bone saw blade the oscillating saw remains the standard instrument both for cutting long bones and creating a bed for an endoprosthesis. The application of abrasive water jets offers the possibility of achieving an extremely precise curved cut in bone with no accompanying thermal effect. The thermographically measured absolute temperature increase at the cut edges seen with the water jet was 13 K maximum. The small process forces permit the application in automated handling systems.

[Use of a water jet for synovectomy: in vitro study of feasibility]. / Der Druckwasserstrahl zum selektiven Abtrag der Synovialis--In-vitro-Studie zur Machbarkeit eines neuen Synovektomieverfahrens.

AIM: The selectivity of a water jet (WJ) is already used with clinical advantage in the surgery of liver, brain, kidney and herniated lumbar discs. The aim of the present study was to determine whether a WJ can be used for synovectomy without damaging the joint capsule and the cartilage. METHOD: 60 human cadaver knee specimens (67 +/- 14 years) were dissected into synovial and cartilage samples. They were randomly assessed to four pressure groups (pW = 3; 6; 9; 12 MPa) and three jet surface angles (beta = 30; 60; 90 degrees) The nozzle diameter was dD = 0.12 mm, the stand off distance of the jet was s = 10 mm with a feed rate of vV = 2 mm/s. The acquired parameters were depth of the cuts, histological layer, and change of the samples thickness. RESULT: There was a correlation of the cutting depth and the pressure (pW), whereas the jet-surface angle (beta) showed no correlation. The synovial layer of the cut likewise correlated with the pressure. At pW = 6 MPa the stratum subsynoviale could be cut selectively without damaging the fibrous capsule or the cartilage. The increase of the samples thickness was caused by an interstitial oedema. CONCLUSION: The different mechanical properties of the joint capsule and the stratum subsynoviale lead to the selective cutting of the water jet. Since the joint capsule was not damaged, the feasibility of WJ synovectomy has been proven. The device can be used for synovectomy in parts of the joint that are not visible as well as in very small joints.

Mismatched wear couple zirconium oxide and aluminum oxide in total hip arthroplasty.

A patient complained about a squeaking noise in his total hip arthroplasty. Clinical evaluation revealed good function, and there were no signs of loosening on the radiograph. Physiotherapy did not alter this phenomenon, and ultimately a revision was performed 42 months after the first surgery. The analysis of the retrievals revealed that a zirconium oxide ceramic head had been paired with a monolithic alumina ceramic cup. The cup showed large deviations from an ideal sphere but minor wear signs. The head exhibited heavy local damage in the articulation zone. This damage might have been caused by the observed unsatisfactory fit between cup and ball, resulting in high stress concentrations and increased wear of the zirconium head. The characteristics of the zirconium and aluminum ceramics pairing might have worsened the process. The combination of implants used in this retrieved wear couple was never approved. To prevent such problems, components of different manufacturers should never be mixed and matched unless explicitly stated.

Duration and frequency of every day activities in total hip patients.

Little knowledge about frequency and duration of daily activities in patients after total hip arthroplasty is available. Such information is required for the definition of realistic load collectives for pre-clinical testing of prostheses. It could also be helpful for the quantitative evaluation of surgery outcome with different prosthesis types. The purpose of this study was to develop and apply a system for the determination of frequency and duration of patient activities in their habitual environment and to compare the results to a clinical outcome score (Harris hip score).A portable activity monitoring system (weight 1.6 kg including batteries) was designed using a Palm top computer, 2 inclination sensors for the thigh and calf and one goniometer positioned at the knee joint. An algorithm was developed to identify frequency and duration of the activities lying, sitting, standing, walking and stair climbing from the signals of the 3 sensors. 42 patients participated in the study and were equipped with the system in the morning at their home. Datasets of 31 patients (age 62.5+/-11.5 y) covered more than 6h (9.8 +/- 1.6 h) and were included in the analysis. Prosthesis specific data as well as the Harris hip score were collected. The most frequent patient activity was sitting (44.3% of the time), followed by standing (24.5%), walking (10.2%), lying (5.8%) and stair climbing (0.4%). The median number of steps/stairs was 6048/164. The number of step cycles representing one year in vivo use should, consequently, be increased to 1.1 million. The Harris hip score (91.4 +/- 9.8) correlated significantly with the number of stairs (r(2) = 0.26, p = 0.003) and showed a positive tendency with the number of steps per day. No differences in activity levels between prosthesis specific factors were found.

[Water jet discotomy with microinvasive approach--in vitro testing and initial clinical aspects of a new procedure]. / Die Wasserstrahldiskotomie im mikroinvasiven Zugang--In-vitro-Testung und erste klinische Aspekte eines neuen Verfahrens.

AIM: The difference in consistence of the nucleus pulposus and the annulus fibrosus allows the water jet to selectively remove the nucleus in a closed vertebral disc at a certain pressure range. The aim of the study was to investigate the use of water jet cutting in microinvasive spinal surgery. METHODS: A comparison in terms of efficiency between the water jet and those of the laser and APLD (automatic percutaneous lumbar discotomy) was achieved by plastic reconstruction of the resected spaces using the in-vitro-model of the spinal column of young pigs. The in-vitro-study was followed by a prospective clinical study with 21 patients. RESULTS: The in-vitro-employment of the three different methods showed that there were no significant differences in volume of the removed nucleus material. During the use of the hydro jet at 50 bar and simultaneous suction the intradiscal pressure measured in vitro remained below 1 bar. Clinical tests on the 21 patients showed good to very good results in 71% of the patients tested (mean follow-up 5.8 months). No complications were found. As working mechanism the pure mechanical effect and the influence on chemical processes within the nucleus remain points for discussion. CONCLUSION: The current studies results demonstrate that hydrojet spinal surgery might be a safe new method for surgery of disc protrusion and contained prolapse.

[Massive acute hypotonic hyperhydration following arthroscopic synovectomy]. / Massive akute hypotone Hyperhydration nach arthroskopischer Synovektomie.

We report the case of a 4 year old boy who developed a massive water intoxication as a complication during knee arthroscopy. The sodium plasma concentration dropped to 100 mmol/l postoperatively. This complication may be triggered by prolonged surgery time, excessive intra-articular pressure, capsular tears and low body weight. To prevent massive incorporation of hypoosmolar fluid, the inflation of a tourniquet as well as the use of NaCl 0,9% as irrigation fluid seems to be of advantage. The guidelines for replacing sodium in hyponatremia are discussed according to literature. In general, hyponatremia should be corrected in the same amount of time as it took for it to develop.

The use of water-jetting technology in prostheses revision surgery-first results of parameter studies on bone and bone cement.

Water-jet cutting techniques have been used in industrial applications for many different materials. Recently these techniques have been developed into a revolutionary cutting tool for soft tissues in visceral surgery. The present study investigates the usage of this cutting technology for the revision surgery of endoprostheses. In the first part of the study, samples of bovine bone and acrylic bone cement (PMMA) were cut using an industrial jet cutting device with pure water. Below 400 bar, only PMMA was cut; above 400 bar, bone was also cut, but only pressures above 800 bar resulted in clinically useful rates of material removal (cut depth 2. 4 mm at 10 mm/min traverse speed). In the second part of the study, the effect of adding biocompatible abrasives to the water in order to reduce the required pressure was investigated, resulting in a significantly higher removal of material. At 600 bar, PMMA was cut 5. 2 mm deep with plain water and 15.2 mm deep with added abrasives. The quality of the cuts was increased by the abrasive. Though there was no clear selectivity between bone and PMMA any more, the rate of material removal at similar pressures was significantly higher for PMMA than for bone (600 bar: 1.6 mm cut depth for bone samples, 15.2 mm for PMMA). The measured cut depths with either method were not influenced by a change of the cutting direction with respect to the main direction of the osteons in the bone. However, a reduction of the jet surface angle (90 degrees to 23 degrees ) resulted for bone in a significantly lower cut depth at 600 bar (plain water: 0.62 mm vs. 0.06 mm; abrasive: 1.61 mm vs. 0.60 mm). The laboratory experiments indicate that abrasive water jets may be suitable for cutting biomaterials like bone and bone cement.

[Water jet cutting for bones and bone cement--parameter study of possibilities and limits of a new method]. / Water Jet Cutting zur Bearbeitung von Knochen und Knochenzement--Parameterstudie zu Möglichkeiten und Grenzen einer neuen Methode.

Water jet techniques have been used in industrial cutting, drilling and cleaning applications for more than 30 years. Plain water is typically used for the cutting of non-metallic materials. The addition of abrasive substances to the stream allows almost any material to be cut. The first medical applications were reported in the early 1980s, when the water jet was used to cut organs. The present study investigates the use of water jet cutting technology for endoprosthesis revision surgery. Bone and PMMA (polymethylmethacrylate) samples were cut at different pressures using an industrial water jet cutting device. Using plain water at 400 bar, PMMA was cut selectively without damaging the bone; above 400 bar, bone was also cut, but the cutting depths in PMMA were significantly greater (p < 0.05). Adding a water-soluble abrasive disaccharide to the water results in a significantly higher removal rate for both materials (p < 0.05), but selectivity is lost, although the differences in cutting depth between the two materials was significant (p < 0.05). With an abrasive, the quality of the cut was better for both materials. The water jet technology--in particular the abrasive technique--can be used to cut biomaterials such as bone and bone cement. The diameter of the jet is a great advantage when working in the confined area at the prosthesis interface. The cutting process is essentially cold, thus eliminating a thermal effect, and the jet reaction forces are relatively low. Accurate manipulation of the hydro jet nozzle is possible both manually and by robot. The results obtained show that it is possible to remove prostheses with this cutting technique, rapidly and with little damage to the surrounding tissue. Problem areas are the development of sterile pumps and the "depth control" of the jet.