Increasing the Beam Width and Intensity with Refraction Power Effect Using a Combination of Beam Mirrors and Concave Mirrors for Surgical-Fluorescence-Emission-Guided Cancer Monitoring Method.

The primary goal during cancer removal surgery is to completely excise the malignant tumor. Because the color of the tumor and surrounding tissues is very similar, it is difficult to observe with the naked eye, posing a risk of damaging surrounding blood vessels during the tumor removal process. Therefore, fluorescence emission is induced using a fluorescent contrast agent, and color classification is monitored through camera imaging. LEDs must be irradiated to generate the fluorescent emission electromotive force. However, the power and beam width of the LED are insufficient to generate this force effectively, so the beam width and intensity must be increased to irradiate the entire lesion. Additionally, there should be no shaded areas in the beam irradiation range. This paper proposes a method to enhance the beam width and intensity while eliminating shadow areas. A total reflection beam mirror was used to increase beam width and intensity. However, when the beam width increased, a shadow area appeared at the edge, limiting irradiation of the entire lesion. To compensate for this shadow area, a concave lens was combined with the beam mirror, resulting in an increase in beam width and intensity by more than 1.42 times and 18.6 times, respectively. Consequently, the beam width reached 111.8°, and the beam power was 13.6 mW. The proposed method is expected to be useful for observing tumors through the induction of fluorescence emission during cancer removal surgery or for pathological examination in the pathology department.

Histological and Molecular Biological Changes in Canine Skin Following Acute Radiation Therapy-Induced Skin Injury.

Radiation therapy is a crucial cancer treatment, but it can damage healthy tissues, leading to side effects like skin injuries and molecular alterations. This study aimed to elucidate histological and molecular changes in canine skin post-radiation therapy (post-RT) over nine weeks, focusing on inflammation, stem cell activity, angiogenesis, keratinocyte regeneration, and apoptosis. Four male beagles received a cumulative radiation dose of 48 Gy, followed by clinical observations, histological examinations, and an RT-qPCR analysis of skin biopsies. Histological changes correlated with clinical recovery from inflammation. A post-RT analysis revealed a notable decrease in the mRNA levels of Oct4, Sox2, and Nanog from weeks 1 to 9. VEGF 188 levels initially saw a slight increase at week 1, but they had significantly declined by week 9. Both mRNA and protein levels of COX-2 and Keratin 10 significantly decreased over the 9 weeks following RT, although COX-2 expression surged in the first 2 weeks, and Keratin 10 levels increased at weeks 4 to 5 compared to normal skin. Apoptosis peaked at 2 weeks and diminished, nearing normal by 9 weeks. These findings offer insights into the mechanisms of radiation-induced skin injury and provide guidance for managing side effects in canine radiation therapy.

Optical Methods for Optimizing Fluorescence Imaging Field of View and Image Quality in Surgical Guidance Procedures.

Cancer surgery is aimed at complete tumor resection and accurate lymph node detection. However, numerous blood vessels are distributed within the tumor, and the colors of the tumor, blood vessels, and lymph nodes are similar, making observations with the naked eye difficult. Therefore, tumors, blood vessels, and lymph nodes can be monitored via color classification using an operating microscope to induce fluorescence emission. However, as the beam width of the LED required to induce fluorescence emission is narrow and the power loss of the beam is significant at a certain working distance, there are limitations to inducing fluorescence emission, and light reflection occurs in the observation image, obstructing the view of the observation area. Therefore, the removal of reflected light is essential to avoid missing the diagnosis of the lesion under observation. This paper proposes the use of a beam mirror and polarizing filter to increase the beam width and beam intensity. The refraction and reflection effects of the beam were utilized using the beam mirror, and the rotation angle of the polarizing filter was adjusted to remove light reflection. Consequently, the minimum beam power using the beam mirror was 10.9 mW, the beam width was doubled to 40.2°, and more than 98% of light reflection was removed at 90° and 270°. With light reflection effectively eliminated, clear observation of lesions is possible. This method is expected to be used effectively in surgical, procedural, and diagnostic departments.

The Long-Term Outcomes and Risk Factors of Complications After Fontan Surgery: From the Korean Fontan Registry (KFR).

BACKGROUND AND OBJECTIVES: This study aimed to analyze the outcomes of Fontan surgery in the Republic of Korea, as there were only a few studies from Asian countries. METHODS: The medical records of 1,732 patients who underwent Fontan surgery in 10 cardiac centers were reviewed. RESULTS: Among them, 1,040 (58.8%) were men. The mean age at Fontan surgery was 4.3±4.2 years, and 395 (22.8%) patients presented with heterotaxy syndrome. According to the types of Fontan surgery, 157 patients underwent atriopulmonary (AP) type; 303, lateral tunnel (LT) type; and 1,266, extracardiac conduit (ECC) type. The overall survival rates were 91.7%, 87.1%, and 74.4% at 10, 20, and 30 years, respectively. The risk factors of early mortality were male, heterotaxy syndrome, AP-type Fontan surgery, high mean pulmonary artery pressure (mPAP) in pre-Fontan cardiac catheterization, and early Fontan surgery year. The risk factors of late mortality were heterotaxy syndrome, genetic disorder, significant atrioventricular valve regurgitation (AVVR) before Fontan surgery, high mPAP in pre-Fontan cardiac catheterization, and no fenestration. CONCLUSIONS: In Asian population with a high incidence of heterotaxy syndrome, the heterotaxy syndrome was identified as the poor prognostic factors for Fontan surgery. The preoperative low mPAP and less AVVR are associated with better early and long-term outcomes of Fontan surgery.

Histo-pillar strip for optimal histogel block construction and biomarker analysis in 3D-lung cancer patient-derived organoids.

This study proposed an optimized histogel construction method for histological analysis by applying lung cancer patient-derived organoids (PDOs) to the developed histo-pillar strip. Previously, there is the cultured PDOs damage problem during the histogel construction due to forced detachment of the Matrigel spots from the 96-well plate bottom. To address this issue, we cultured PDO on the proposed Histo-pillar strips and then immersed them in 4% paraformaldehyde fixation solution to self-isolate PDO without damage. The 4µl patient-derived cell (PDC)/Matrigel mixtures were dispensed on the surface of a U-shaped histo-pillar strip, and the PDCs were aggregated by gravity and cultured into PDOs. Cultured PDOs were self-detached by simply immersing them in a paraformaldehyde fixing solution without physical processing, showing about two times higher cell recovery rate than conventional method. In addition, we proposed a method for embedding PDOs under conditions where the histogel temperature was maintained such that the histogel did not harden, thereby improving the problem of damaging the histogel block in the conventional sandwich histogel construction method. We performed histological and genotyping analyses using tumor tissues and PDOs from two patients with lung adenocarcinoma. Therefore, the PDO culture and improved histogel block construction method using the histo-pillar strip proposed in this study can be employed as useful tools for the histological analysis of a limited number of PDCs.

U-Shape Pillar Strip for 3D Cell-Lumped Organoid Model (3D-COM) Mimicking Lung Cancer Hypoxia Conditions in High-Throughput Screening (HTS).

Hypoxia is a representative tumor characteristic associated with malignant progression in clinical patients. Engineered in vitro models have led to significant advances in cancer research, allowing for the investigation of cells in physiological environments and the study of disease mechanisms and processes with enhanced relevance. In this study, we propose a U-shape pillar strip for a 3D cell-lumped organoid model (3D-COM) to study the effects of hypoxia on lung cancer in a high-throughput manner. We developed a U-pillar strip that facilitates the aggregation of PDCs mixed with an extracellular matrix to make the 3D-COM in 384-plate array form. The response to three hypoxia-activated prodrugs was higher in the 3D-COM than in the 2D culture model. The protein expression of hypoxia-inducible factor 1 alpha (HIF-1α) and HIF-2α, which are markers of hypoxia, was also higher in the 3D-COM than in the 2D culture. The results show that 3D-COM better recapitulated the hypoxic conditions of lung cancer tumors than the 2D culture. Therefore, the U-shape pillar strip for 3D-COM is a good tool to study the effects of hypoxia on lung cancer in a high-throughput manner, which can efficiently develop new drugs targeting hypoxic tumors.

A Method to Reduce Tension Differences in Pull/Push Manipulation for a Robot in Fluorescence Emission-Guided Surgical Microscopy.

MOTIVATION: A fluorescence emission-guided microscope used to monitor the outcome of cancer removal surgery is highly effective when employing a manipulator to motorize and switch the observation direction. It is necessary to minimize the alignment of looper tension between the stands for pull/push to change the direction of the manipulator and reduce the error rate caused by tension differences. This paper presents a method to minimize the error rate of looper tension between the stands. METHODS: \The looper is inserted between the stands of the manipulator to minimize the difference in tension and make the stress on the pull and push of the looper constant. The constant stress allows the manipulator to move stably in left/right, up/down, and left/right movements, which will be effective for full-camera observation and close-up shots of the end effector. RESULTS: Reducing the tolerance for differences in the manipulator's looper tension (angle and tension) is crucial. When the input value of the looper tension angle is 50°, the output should closely match 50°. Consequently, the measured response has a tolerance of ±49.98%, resulting in an error rate of .02% (1/50th level). CONCLUSION: A method is proposed to minimize the error rate of the manipulator's looper tension in a robot-based fluorescence emission-guided microscope used to observe the status of cancer surgery. As a result, a stable manipulator with a minimal error rate can achieve a 3.986x magnification for close-up observation by switching between high and low orientations.

Decreased incidence of Kawasaki disease in South Korea during the SARS-CoV-2 pandemic.

Purpose: Analyzing Kawasaki disease epidemiology during the SARS-CoV-2 pandemic in South Korea using 2012-2020 National Health Insurance Service data. Methods: The incidence of Kawasaki disease for 2012-2020 was investigated to identify changes in incidence after the start of the pandemic. National Health Insurance Service data from the Republic of Korea were used. Kawasaki disease was defined based on the International Statistical Classification of Diseases and Related Health Problems, the Tenth Revision diagnostic code (M30.3), and the intravenous immunoglobulin prescription code. Prescription history was collected for the following medications: intravenous immunoglobulin, aspirin, corticosteroids, tumor necrosis factor-α antagonist, clopidogrel, and anticoagulation drugs. Results: The Kawasaki disease incidence per 100,000 individuals younger than 5 years was 238.9, 230.0, and 141.2 in 2018, 2019, and 2020, respectively. Regarding the incidence from 2012 to 2020, it was the highest in 2018 and decreased to 141.2 (p < 0.001) in 2020, after the start of the pandemic. In 2020, 28.3% of all patients with KD were infants, a percentage significantly higher than that of the previous year (p < 0.001). There was biphasic seasonality in the monthly Kawasaki disease incidence. The Kawasaki disease incidence was the highest in winter followed by that in early summer. Conclusion: After the start of the pandemic, the Kawasaki disease incidence decreased, and the percentage of patients with Kawasaki disease aged <1 year increased. These findings provide support for the hypothesis suggesting an infectious trigger in Kawasaki disease.

Gadolinium-Based Magnetic Resonance Theranostic Agent with Gallic Acid as an Anti-Neuroinflammatory and Antioxidant Agent.

Studies in the field have actively pursued the incorporation of diverse biological functionalities into gadolinium-based contrast agents, aiming at the amalgamation of MRI imaging and therapeutic capabilities. In this research, we present the development of Gd-Ga, an anti-neuroinflammatory MR contrast agent strategically designed to target inflammatory mediators for comprehensive imaging diagnosis and targeted lesion treatment. Gd-Ga is a gadolinium complex composed of 1,4,7-tris(carboxymethylaza)cyclododecane-10-azaacetylamide (DO3A) conjugated with gallic acid (3,4,5-trihydroxybenzoic acid). Upon intravenous administration in LPS-induced mouse models, Gd-Ga demonstrated a remarkable three-fold increase in signal-to-noise (SNR) variation compared to Gd-DOTA, particularly evident in both the cortex and hippocampus 30 min post-MR monitoring. In-depth investigations, both in vitro and in vivo, into the anti-neuroinflammatory properties of Gd-Ga revealed significantly reduced protein expression levels of pro-inflammatory mediators compared to the LPS group. The alignment between in silico predictions and phantom studies indicates that Gd-Ga acts as an anti-neuroinflammatory agent by directly binding to MD2. Additionally, the robust antioxidant activity of Gd-Ga was confirmed by its effective scavenging of NO and ROS. Our collective findings emphasize the immense potential of this theranostic complex, where a polyphenol serves as an anti-inflammatory drug, presenting an exceptionally efficient platform for the diagnosis and treatment of neuroinflammation.

Ideal chest compression site for cardiopulmonary resuscitation in fontan circulation patients with dextrocardia.

BACKGROUND: We aimed to identify the ideal chest compression site for cardiopulmonary resuscitation (CPR) in patients with a single ventricle with dextrocardia corrected by Fontan surgery. METHODS: The most recent stored chest computed tomography images of all patients with a single ventricle who underwent Fontan surgery were retrospectively analysed. We reported that the ideal chest compression site is the largest part of the compressed single ventricle. To identify the ideal chest compression site, we measured the distance from the midline of the sternum to the point of the maximum sagittal area of the single ventricle as a deviation and calculated the area fraction of the compressed structures. RESULTS: 58 patients (67.2% male) were analysed. The mean right deviation from the midline of the sternum to the ideal compression site was similar to the mean sternum width (32.85 ± 15.61 vs. 31.05 ± 6.75 mm). When chest compression was performed at the ideal site, the area fraction of the single ventricle significantly increased by 7%, which was greater than that of conventional compression (0.15 ± 0.10 vs. 0.22 ± 0.11, P < 0.05). CONCLUSIONS: When performing CPR on a patient with Fontan circulation with dextrocardia, right-sided chest compression may be better than the conventional location.

Comparative Sensing and Judgment Control System for Temperature Maintenance for Optimal Treatment in Hyperthermic Intraperitoneal Chemotherapy Surgery.

For tumors wherein cancer cells remain in the tissue after colorectal cancer surgery, a hyperthermic anticancer agent is injected into the abdominal cavity to necrotize the remaining cancer cells with heat using a hyperthermic intraperitoneal chemotherapy system. However, during circulation, the processing temperature is out of range and the processing result is deteriorated. This paper proposes a look-up table (LUT) module design method that can stably maintain the processing temperature range during circulation via feedback. If the temperature decreases or increases, the LUT transmits a command signal to the heat exchanger to reduce or increase heat input, thereby maintaining the treatment temperature range. The command signal for increasing and decreasing heat input is Tp and Ta, respectively. The command signal for the treatment temperature range is Ts. If drug temperatures below 41 and above 43 °C are input to the LUT, it sends a Tp or Ta signal to the heat exchanger to increase or decrease the input heat, respectively. If the drug's temperature is 41-43 °C, the LUT generates a Ts signal and proceeds with the treatment. The proposed system can automatically control drug temperature using temperature feedback to ensure rapid, accurate, and safe treatment.

Effects of Fermented Polygonum cuspidatum on the Skeletal Muscle Functions.

Plant extract fermentation is widely employed to enhance the nutritional and pharmaceutical value of functional foods. Polygonum cuspidatum (Pc) contains flavonoids, anthraquinones, and stilbenes, imparting protective effects against inflammatory diseases, cancer, diabetes, and cardiovascular diseases. However, the effects of fermented Pc on skeletal muscle strength remain unexplored. In this study, we generated fermented Pc using a complex of microorganisms containing Lactobacillus spp. (McPc) and assessed its effects on muscle strength and motor function in mice. Compared to unfermented Pc water extract, elevated levels of emodin and resveratrol were noted in McPc. This was identified and quantified using UPLC-QTOF/MS and HPLC techniques. Gene expression profiling through RNA-seq and quantitative RT-PCR revealed that McPc administration upregulated the expression of genes associated with antioxidants, glycolysis, oxidative phosphorylation, fatty acid oxidation, and mitochondrial biogenesis in cultured C2C12 myotubes and the gastrocnemius muscle in mice. McPc significantly improved skeletal muscle strength, motor coordination, and traction force in mice subjected to sciatic neurectomy and high-fat diet (HFD). McPc administration exhibited more pronounced improvement of obesity, hyperglycemia, fatty liver, and hyperlipidemia in HFD mice compared to control group. These findings support the notion that emodin and resveratrol-enriched McPc may offer health benefits for addressing skeletal muscle weakness.

Adjustment of the Length Variation With Wire-driven Using the Stand Looper Tension Technique for Surgical Robot Applications.

MOTIVATION: The wire-driven method used in the field of surgical robots has the advantage of light weight. However, in the process of pull and push for the operation of forceps, the length of the wire is not match, causing malfunction. To solve this problem, the application of looper-tension technology would be suitable. This paper contributes to adjusting the length of the wire by inserting a stand between the wire-driven joints and adding a looper-tension between the stands to adjust the rotation radius of the roll. METHODS: The method consisting of three rolls and loopers for connection between the stands minimizes errors by adjusting the length of the loop in a balanced state due to the rotation change of the roll during the pull and push of the robot arm. The angle and tension applied to the looper are 25° and 8.6 MPa, respectively. RESULTS: An output response can be obtained when the reference operating point fluctuates by ± 50% of the input angle and tension, and if the reference operating point fluctuates by ± 30% while the input angle and tension are fixed, the output response occurs oppositely. When a .15 kg object is loaded up/down with 1.5 newton using forceps, the change in length of pull and push coincides. CONCLUSION: The advantage is that the error of wire pull, and push operation can be reduced, and accurate operation can be expected. Since the proposed technology is applied between joints, the integration process is not complicated, and the weight is light.

Multi-Asymmetric Irradiation Method Using a Ring Array to Obtain an Emission-Capable LED Beam Power Effect to Observe Cancer Removal Status in a Surgical Microscope.

The light emitting diodes (LEDs) used in surgical fluorescence microscopes have weak power, to induce fluorescence emission. The LED induces fluorescence emission throughout a lesion due to its large beam width; however, the beam irradiation intensity is not uniform within the beam width, resulting in a fluorescence emission induction difference. To overcome this problem, this study proposes an asymmetric irradiation array for supplying power uniformly throughout the beam width of the LED and increasing the intensity of the LED. To increase the irradiation power of the LEDs, a multi-asymmetric irradiation method with a ring-type array structure was used. The LED consisted of eight rings, and the space between the LEDs, the placement position, and the placement angle were analyzed to devise an experimental method using 3D printing technology. To test the irradiation power of the LED, the working distance (WD) between the LED and target was 30 cm. The bias voltage of the LED for irradiating the light source was 5.0 V and the measured power was 4.63 mW. The brightness (lux) was 1153 lx. Consequently, the LED satisfied the fluorescence emission induction conditions. The diameter of the LED-irradiated area was 9.5 cm. Therefore, this LED could be used to observe fluorescent emission-guided lesions. This study maximized the advantages of LEDs with optimal conditions for fluorescence emission by increasing the beam width, irradiation area, and energy efficiency, using a small number of LEDs at the maximum WD. The proposed method, optimized for fluorescence expression-induced surgery, can be made available at clinical sites by mass producing them through semiconductor processes.

Late development of intra-atrial reentrant tachycardia in lateral tunnel Fontan patients and the preventive role of prophylactic cryoablation.

OBJECTIVE: Intra-atrial reentrant tachycardia is an important late-onset complication in patients undergoing the Fontan procedure. However, the protective effects of prophylactic cryoablation against late-onset intra-atrial reentrant tachycardia are unclear. This study investigated the late development of intra-atrial reentrant tachycardia in patients undergoing the lateral tunnel Fontan procedure and the role of prophylactic cryoablation. METHODS: This was a single-center retrospective cohort study of patients who underwent the lateral tunnel Fontan procedure between 1988 and 2003. Univariate and multivariable competing risks regression models were used to determine the associations of prophylactic cryoablation and covariates with the outcomes of interest: late-onset intra-atrial reentrant tachycardia, all-cause mortality, and cardiovascular mortality. RESULTS: In total, 130 patients who underwent the lateral tunnel Fontan procedure, 30 of whom had undergone prophylactic cryoablation, were included in this study and followed up for a median of 23.6 years (interquartile range, 17.7-26.5). Intra-atrial reentrant tachycardia was identified in 14 patients (10.8%), none of whom underwent prophylactic cryoablation. The median Fontan-to-intra-atrial reentrant tachycardia time was 17.2 years (interquartile range, 11.1-23.1). Prophylactic cryoablation was protective against late-onset intra-atrial reentrant tachycardia (P < .0001) and cardiovascular mortality (P < .0001) in the type 3 test. CONCLUSIONS: None of the patients who underwent prophylactic cryoablation developed late-onset intra-atrial reentrant tachycardia during a median follow-up time of 22.9 years. Our study demonstrated that prophylactic cryoablation was effective in preventing late-onset intra-atrial reentrant tachycardia and cardiovascular mortality in patients undergoing the lateral tunnel Fontan.

Cancer organoid-based diagnosis reactivity prediction (CODRP) index-based anticancer drug sensitivity test in ALK-rearrangement positive non-small cell lung cancer (NSCLC).

BACKGROUND: Recently, cancer organoid-based drug sensitivity tests have been studied to predict patient responses to anticancer drugs. The area under curve (AUC) or IC50 value of the dose-response curve (DRC) is used to differentiate between sensitive and resistant patient's groups. This study proposes a multi-parameter analysis method (cancer organoid-based diagnosis reactivity prediction, CODRP) that considers the cancer stage and cancer cell growth rate, which represent the severity of cancer patients, in the sensitivity test. METHODS: On the CODRP platform, patient-derived organoids (PDOs) that recapitulate patients with lung cancer were implemented by applying a mechanical dissociation method capable of high yields and proliferation rates. A disposable nozzle-type cell spotter with efficient high-throughput screening (HTS) has also been developed to dispense a very small number of cells due to limited patient cells. A drug sensitivity test was performed using PDO from the patient tissue and the primary cancer characteristics of PDOs were confirmed by pathological comparision with tissue slides. RESULTS: The conventional index of drug sensitivity is the AUC of the DRC. In this study, the CODRP index for drug sensitivity test was proposed through multi-parameter analyses considering cancer cell proliferation rate, the cancer diagnosis stage, and AUC values. We tested PDOs from eight patients with lung cancer to verify the CODRP index. According to the anaplastic lymphoma kinase (ALK) rearrangement status, the conventional AUC index for the three ALK-targeted drugs (crizotinib, alectinib, and brigatinib) did not classify into sensitive and resistant groups. The proposed CODRP index-based drug sensitivity test classified ALK-targeted drug responses according to ALK rearrangement status and was verified to be consistent with the clinical drug treatment response. CONCLUSIONS: Therefore, the PDO-based HTS and CODRP index drug sensitivity tests described in this paper may be useful for predicting and analyzing promising anticancer drug efficacy for patients with lung cancer and can be applied to a precision medicine platform.

Design of a Miniature Observation Robot for Light Emitting Diode Irradiation and Indocyanine Green Fluorescence-emission Guided Lymph Node Monitoring in Operating Rooms.

MOTIVATION: Typical surgical microscopes used for fluorescence-based lymph node detection experience limitations such as weight and restricted adjustability of the integrated light emitting diode (LED) and camera. This restricts the capture of detailed images of specific regions within the lesion. RESEARCH GOAL: This study proposes a miniature observation robot design that offers adjustable working distance (WD) and rotational radius, along with zoom-in/zoom-out functionality. METHODS: A five-degree-of-freedom manipulator was designed, with the end effector incorporating an LED and concave lens to widen the beam width for comprehensive lesion illumination. Additionally, a long-pass filter was integrated into the camera system to enhance image resolution. EXPERIMENTAL RESULTS: Experiments were conducted using a fluorescence-expressing phantom to evaluate the performance of the robot. Results demonstrated a captured image resolution of 9600 × 3240 pixels and a zoom-in/zoom-out capacity of up to 3.68 times. CONCLUSION: The proposed robot design is cost-effective and highly adjustable, enabling suitability for rapid and accurate detection of fresh lymph nodes during surgeries. The robot's capability to detect small lesions (<1 cm), as validated by phantom tests, holds promise for the detection of minute lymph nodes.

Single Quasi-Symmetrical LED with High Intensity and Wide Beam Width Using Diamond-Shaped Mirror Refraction Method for Surgical Fluorescence Microscope Applications.

To remove tumors with the same blood vessel color, observation is performed using a surgical microscope through fluorescent staining. Therefore, surgical microscopes use light emitting diode (LED) emission and excitation wavelengths to induce fluorescence emission wavelengths. LEDs used in hand-held type microscopes have a beam irradiation range of 10° and a weak power of less than 0.5 mW. Therefore, fluorescence emission is difficult. This study proposes to increase the beam width and power of LED by utilizing the quasi-symmetrical beam irradiation method. Commercial LED irradiates a beam 1/r2 distance away from the target (working distance). To obtain the fluorescence emission probability, set up four mirrors. The distance between the mirrors and the LED is 5.9 cm, and the distance between the mirrors and the target is 2.95 cm. The commercial LED reached power on target of 8.0 pW within the wavelength band of 405 nm. The power reaching the target is 0.60 mW in the wavelength band of 405 nm for the LED with the beam mirror attachment method using the quasi-symmetrical beam irradiation method. This result is expected to be sufficient for fluorescence emission. The light power of the mirror was increased by approximately four times.

3D cell subculturing pillar dish for pharmacogenetic analysis and high-throughput screening.

A pillar dishe for subculture of 3D cultured cells on hydrogel spots (Matrigel and alginate) have been developed. Cells cultured in 3D in an extracellular matrix (ECM) can retain their intrinsic properties, but cells cultured in 2D lose their intrinsic properties as the cells stick to the bottom of the well. Previously, cells and ECM spots were dispensed on a conventional culture dish for 3D cultivation. However, as the spot shape and location depended on user handling, pillars were added to the dish to realize uniform spot shape and stable subculture, supporting 3D cell culture-based high-throughput screening (HTS). Matrigel and alginate were used as ECMs during 6-passage subculture. The growth rate of lung cancer cell (A549) was higher on Matrigel than on alginate. Cancer cell was subcultured in three dimensions in the proposed pillar dish and used for drug screening and differential gene expression analysis. Interestingly, stemness markers, which are unique characteristics of lung cancer cells inducing drug resistance, were upregulated in 3D-subcultured cells compared with those in 2D-subcultured cells. Additionally, the PI3K/Akt/mTOR, VEGFR1/2, and Wnt pathways, which are promising therapeutic targets for lung cancer, were activated, showing high drug sensitivity under 3D-HTS using the 3D-subcultured cells.