Evaluation of cell disruption methods for protein and coenzyme Q10 quantification in purple non-sulfur bacteria.

A recent focus has been on the recovery of single-cell protein and other nutritionally valuable bioproducts, such as Coenzyme Q10 (CoQ10) from purple non-sulfur bacteria (PNSB) biomass following wastewater treatment. However, due to PNSB's peculiar cell envelope (e.g., increased membrane cross-section for energy transduction) and relatively smaller cell size compared to well-studied microbial protein sources like yeast and microalgae, the effectiveness of common cell disruption methods for protein quantification from PNSB may differ. Thus, this study examines the efficiency of selected chemical (NaOH and EDTA), mechanical (homogenization and bead milling), physical (thermal and bath/probe sonication), and combined chemical-mechanical/physical treatment techniques on the PNSB cell lysis. PNSB biomass was recovered from the treatment of gas-to-liquid process water. Biomass protein and CoQ10 contents were quantified based on extraction efficiency. Considering single-treatment techniques, bead milling resulted in the best protein yields (p < 0.001), with the other techniques resulting in poor yields. However, the NaOH-assisted sonication (combined chemical/physical treatment technique) resulted in similar protein recovery (p = 1.00) with bead milling, with the former having a better amino acid profile. For example, close to 50% of the amino acids, such as sensitive ones like tryptophan, threonine, cystine, and methionine, were detected in higher concentrations in NaOH-assisted sonication (>10% relative difference) compared to bead-milling due to its less disruptive nature and improved solubility of amino acids in alkaline conditions. Overall, PNSB required more intensive protein extraction techniques than were reported to be effective on other single-cell organisms. NaOH was the preferred chemical for chemical-aided mechanical/physical extraction as EDTA was observed to interfere with the Lowry protein kit, resulting in significantly lower concentrations. However, EDTA was the preferred chemical agent for CoQ10 extraction and quantification. CoQ10 extraction efficiency was also suspected to be adversely influenced by pH and temperature.

Transforming polypropylene waste into transparent anti-corrosion weather-resistant and anti-bacterial superhydrophobic films.

The global pollution crisis arising from the accumulation of plastic in landfills and the environment necessitates addressing plastic waste issues. Notably, polypropylene (PP) waste accounts for 20% of total plastic waste and holds promise for hydrophobic applications in the realm of recycling. Herein, the transparent and non-transparent superhydrophobic films made from waste PP are reported. A hierarchical structure with protrusions is induced through spin-casting and thermally induced phase separation. The films had a water contact angle of 159° and could vary in thickness, strength, roughness, and hydrophobicity depending on end-user requirements. The Bode plot indicated enhanced corrosion resistance in the superhydrophobic films. Antibacterial trials with Escherichia coli and Staphylococcus aureus microbial solutions showed that the superhydrophobic film had a significantly lower rate of colony-forming units compared to both the transparent surface and the control blank sample. Moreover, a life cycle assessment revealed that the film production resulted in a 62% lower embodied energy and 34% lower carbon footprint compared to virgin PP pellets sourced from petroleum. These films exhibit distinctiveness with their dual functionality as coatings and freestanding films. Unlike conventional coatings that require chemical application onto the substrate, these films can be mechanically applied using adhesive tapes on a variety of surfaces. Overall, the effective recycling of waste PP into versatile superhydrophobic films not only reduces environmental impact but also paves the way for a more sustainable and eco-friendly future.

Altered Regulation of the Glucose Transporter GLUT3 in PRDX1 Null Cells Caused Hypersensitivity to Arsenite.

Targeting tumour metabolism through glucose transporters is an attractive approach. However, the role these transporters play through interaction with other signalling proteins is not yet defined. The glucose transporter SLC2A3 (GLUT3) is a member of the solute carrier transporter proteins. GLUT3 has a high affinity for D-glucose and regulates glucose uptake in the neurons, as well as other tissues. Herein, we show that GLUT3 is involved in the uptake of arsenite, and its level is regulated by peroxiredoxin 1 (PRDX1). In the absence of PRDX1, GLUT3 mRNA and protein expression levels are low, but they are increased upon arsenite treatment, correlating with an increased uptake of glucose. The downregulation of GLUT3 by siRNA or deletion of the gene by CRISPR cas-9 confers resistance to arsenite. Additionally, the overexpression of GLUT3 sensitises the cells to arsenite. We further show that GLUT3 interacts with PRDX1, and it forms nuclear foci, which are redistributed upon arsenite exposure, as revealed by immunofluorescence analysis. We propose that GLUT3 plays a role in mediating the uptake of arsenite into cells, and its homeostatic and redox states are tightly regulated by PRDX1. As such, GLUT3 and PRDX1 are likely to be novel targets for arsenite-based cancer therapy.

Sustainable Solution for Plastic Pollution: Upcycling Waste Polypropylene Masks for Effective Oil-Spill Management.

The use of Polypropylene PP in disposable items such as face masks, gloves, and personal protective equipment has increased exponentially during and after the COVID-19 pandemic, contributing significantly to microplastics and nanoplastics in the environment. Upcycling of waste PP provides a useful alternative to traditional thermal and mechanical recycling techniques. It transforms waste PP into useful products, minimizing its impact on the environment. Herein, we synthesized an oil-sorbent pouch using waste PP, which comprises superposed microporous and fibrous thin films of PP using spin coating. The pouch exhibited super-fast uptake kinetics and reached its saturation in fewer than five minutes with a high oil uptake value of 85 g/g. Moreover, it displayed high reusability and was found to be effective in absorbing oil up to seven times when mechanically squeezed between each cycle, demonstrating robust oil-sorption capabilities. This approach offers a potential solution for managing plastic waste while promoting a circular economy.

Designing super-fast trimodal sponges using recycled polypropylene for organics cleanup.

Sorbent pads and films have been commonly used for environmental remediation purposes, but designing their internal structure to optimize access to the entire volume while ensuring cost-effectiveness, ease of fabrication, sufficient strength, and reusability remains challenging. Herein, we report a trimodal sorbent film from recycled polypropylene (PP) with micropores, macro-voids, and sponge-like 3D cavities, developed through selective dissolution, thermally induced phase separation, and annealing. The sorbent has hundreds of cavities per cm2 that are capable of swelling up to twenty-five times its thickness, allowing for super-fast saturation kinetics (within 30 s) and maximum oil sorption (97 g/g). The sorption mechanism follows a pseudo-second-order kinetic model. Moreover, the sorbent is easily compressible, and its structure is retained during oil sorption, desorption, and resorption, resulting in 96.5% reuse efficiency. The oil recovery process involves manually squeezing the film, making the cleanup process efficient with no chemical treatment required. The sorbent film possesses high porosity for effective sorption with sufficient tensile strength for practical applications. Our integrated technique results in a strengthened porous polymeric structure that can be tailored according to end-use applications. This study provides a sustainable solution for waste management that offers versatility in its functionality.

Non-Wettable Microporous Sheets Using Mixed Polyolefin Waste for Oil-Water Separation.

Mixed polyolefin-based waste needs urgent attention to mitigate its negative impact on the environment. The separation of these plastics requires energy-intensive processes due to their similar densities. Additionally, these materials cannot be blended without compatibilizers, as they are inherently incompatible and immiscible. Herein, non-wettable microporous sheets from recycled polyethylene (PE) and polypropylene (PP) are presented. The methodology involves the application of phase separation and spin-casting techniques to obtain a bimodal porous structure, facilitating efficient oil-water separation. The resulting sheets have an immediate and equilibrium sorption uptake of 100 and 55 g/g, respectively, due to the presence of micro- and macro-pores, as revealed by SEM. Moreover, sheets possess enhanced crystallinity, as evidenced by XRD; hence, they retain their structure during sorption and desorption and are reusable with 98% efficiency. The anti-wetting properties of the sheets are enhanced by applying a silane coating, ensuring waterless sorption and a contact angle of 140°. These results highlight the importance of implementing sustainable solutions to recycle plastics and mitigate the oil spill problem.

3D Oleophilic Sorbent Films Based on Recycled Low-Density Polyethylene.

Recycling low-end, one-time-use plastics-such as low-density polyethylene (LDPE)-is of paramount importance to combat plastic pollution and promote sustainability in the modern green economy. This study valorizes LDPE waste by transforming it into 3D oleophilic swellable thin films through a process involving dissolution, phase separation, and extraction. These films are subsequently layered using a customized polypropylene (PP) based nonwoven fabric separator and securely sealed in a zigzag pattern. The zigzag-shaped seal enhances the adhesion of pollutants to the sorbent by providing wire curvatures that increase retention time and uptake capacity. As a result, the sorbent exhibits impressive oil uptake capacities, with immediate and equilibrium values of 120 g/g and 85 g/g, respectively. Notably, the as-prepared sorbent demonstrates low water retention and high selectivity for oil, outperforming commercially available oil sorbents. The unique design involving a 3D-film structure, superposed films, and a zigzag-shaped seal offers a sustainable and value-added solution to the issues of LDPE waste and oil spills on water surfaces.

Reusable Macroporous Oil Sorbent Films from Plastic Wastes.

Plastic waste comprises 15% of the total municipal solid waste and can be a rich source for producing value-added materials. Among them, polyethylene (PE) and polypropylene (PP) account for 60% of the total plastic waste, mainly due to their low-end and one-time-use applications. Herein, we report reusable oil sorbent films made by upcycling waste PE and PP. The as-prepared oil sorbent had an uptake capacity of 55 g/g. SEM analysis revealed a macroporous structure with a pore size range of 1-10 µm, which facilitates oil sorption. Similarly, the contact angle values reflected the oleophilic nature of the sorbent. Moreover, thermal properties and crystallinity were examined using DSC, while mechanical properties were calculated using tensile testing. Lastly, 95% of the sorbed oil could be easily recovered by squeezing mechanically or manually.

Removal of Benzene and Toluene from Synthetic Wastewater by Adsorption onto Magnetic Zeolitic Imidazole Framework Nanocomposites.

Considering the risk associated with exposure to benzene and toluene in water resources, researchers have been motivated to conduct studies to remove them from aqueous solutions. Thus, by performing the present study, the potential of Fe3O4/zeolite imidazolate framework nanoparticles (Fe3O4@ZIF-8) was evaluated for the adsorption of benzene and toluene. Accordingly, the solution pH, Fe3O4@ZIF-8 dosage, mixing time, concentration of benzene and toluene, and temperature, were the parameters considered for conducting the batch experiments, for which their effect on adsorption efficiency was evaluated. Our conducted experiments introduced the neutral pH as the best pH range to obtain the maximum removal. Fitting the adsorption data into the various models revealed the aptness of the Langmuir isotherm equation in describing experimental information and highest adsorption capacity; for benzene it was 129.4, 134.2, 137.3, and 148.2 mg g-1, but for toluene it was 118.4, 125.2, 129.6, and 133.1 mg g-1, for temperature 20, 30, 40, and 50 °C, respectively. Using obtained optimal conditions, the adsorption efficiencies of benzene and toluene were obtained to be 98.4% and 93.1%, respectively. Kinetic studies showed acceptable coefficients for PSO kinetics and confirmed its suitability. Also, the recyclability results showed that for six consecutive periods of the adsorption-desorption process, the percentage of removal decreased by only 6% for benzene and toluene. Moreover, calculating thermodynamic parameter changes for benzene and toluene removal confirmed the favorability and spontaneity of the studied process and its endothermic nature. Considering the above findings, Fe3O4@ZIF-8 was found to be an operative adsorbent for removing pollutants.

Sorption as a rapidly response for oil spill accidents: A material and mechanistic approach.

Accidents involving oil transportation has increase due to directly connection with the elevation of global energy demand. The environmental losses are tremendous and brings huge economic issues to remediate the spilled oil. This report presents an up-to-date review on an overall aspects of oil spill remediation techniques, the fundamentals and advantages of sorption, the most applied materials through diverse types of oil spill sites and oils with variety features, highlight to natural materials and future prospective. As the environment preservation progressively becomes a major social concern issue, the achievement of a worldwide distribution process aligned with environmental legislation and economic viability is crucial to the oil industry. For this, a specific preparation considering several scenarios must be carried out regarding minimization of oil spillages. Since the sorbent materials are decisive for sorption, it was approached the main sorbents: natural, graphenic, nano, polymeric and waste materials, and future trends.

Preparation and characterization of modified rice husks by biological delignification and acetylation for oil spill cleanup.

Cellulose is widely used as an effective sorbent to treat wastewater. Cellulosic sorbents have the advantage of biodegradability, as they are natural plant-based materials, compared with the synthetic materials such as polypropylene (PP) or polyurethane (PU). Among the raw biomass materials used for cellulose production, rice husk is one of the most cost competitive and widely available. In this work, biological treatments are compared to find the most effective treatment method for cellulose fibre production from rice husk. Using biological delignification, cellulose was extracted from raw rice husk and acetylated to acquire hydrophobicity. Delignification was performed using both bacteria and fungi and their results were compared. The white-rot fungi strain using 'Aspergillus flavus CICC 40258' was found to be the most effective treatment method, achieving a modified product with up to 55% w/w cellulose concentration. Acetylation further facilitated the sorption process and the maximum oil uptake capacity using delignification and acetylation treatment was found to be 20 g/g. The as-prepared sorbents exhibited high oil uptake rates and saturation capacity was reached after 5 min of contact with oil. The kinetic study presents a good correlation with the pseudo-second order model. The isothermal studies demonstrated that the oil sorption capacity of rice husk follows the Langmuir model as compared with the Freundlich model.

Application of cadmium-doped ZnO for the solar photocatalytic degradation of phenol.

In this study, photocatalysis of phenol was studied using Cd-ZnO nanorods, which were synthesized by a hydrothermal method. The Cd-ZnO photocatalyst was characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy, and Fourier transform infrared (FT-IR) and UV-Vis spectroscopy. XRD patterns exhibit diffraction peaks indexed to the hexagonal wurtzite structures with the P63mc space group. SEM images showed that the average size of the Cd-ZnO nanorods was about 90 nm. Moreover, the nanorods were not agglomerated and were well-dispersed in the aqueous medium. FT-IR analysis confirmed that a surface modifier (n-butylamine) did not add any functional groups onto the Cd-ZnO nanorods. The dopant used in this study showed reduction of the bandgap energy between valence and conduction of the photocatalyst. In addition, effect of various operational parameters including type of photocatalyst, pH, initial concentration of phenol, amount of photocatalyst, and irradiation time on the photocatalytic degradation of phenol has been investigated. The highest phenol removal was achieved using 1% Cd-ZnO for 20 mg/l phenol at pH 7, 3 g/l photocatalyst, 120 min contact time, and 0.01 mole H2O2.

Adsorption of phosphate on iron oxide doped halloysite nanotubes.

Excess phosphate in water is known to cause eutrophication, and its removal is imperative. Nanoclay minerals are widely used in environmental remediation due to their low-cost, adequate availability, environmental compatibility, and adsorption efficiency. However, the removal of anions with nanoclays is not very effective because of electrostatic repulsion from clay surfaces with a net negative charge. Among clay minerals, halloysite nanotubes (HNTs) possess a negatively charged exterior and a positively charged inner lumen. This provides an increased affinity for anion removal. In this study, HNTs are modified with nano-scale iron oxide (Fe2O3) to enhance the adsorption capacity of the nanosorbent. This modification allowed for effective distribution of these oxide surfaces, which are known to sorb phosphate via ligand exchange and by forming inner-sphere complexes. A detailed characterization of the raw and (Fe2O3) modified HNTs (Fe-HNT) is conducted. Influences of Fe2O3 loading, adsorbent dosage, contact time, pH, initial phosphate concentration, and coexisting ions on the phosphate adsorption capacity are studied. Results demonstrate that adsorption on Fe-HNT is pH-dependent with fast initial adsorption kinetics. The underlying mechanism is identified as a combination of electrostatic attraction, ligand exchange, and Lewis acid-base interactions. The nanomaterial provides promising results for its application in water/wastewater treatment.

3D graphene-based nanostructured materials as sorbents for cleaning oil spills and for the removal of dyes and miscellaneous pollutants present in water.

Oil spills over seawater and dye pollutants in water cause economic and environmental damage every year. Among various methods to deal oil spill problems, the use of porous materials has been proven as an effective strategy. In recent years, graphene-based porous sorbents have been synthesized to address the shortcomings associated with conventional sorbents such as their low uptake capacity, slow sorption rate, and non-recyclability. This article reviews the research undertaken to control oil spillage using three-dimensional (3D) graphene-based materials. The use of these materials for removal of dyes and miscellaneous environmental pollutants from water is explored and the application of various multifunctional 3D oil sorbents synthesized by surface modification technique is presented. The future prospects and limitations of these materials as sorbents are also discussed.

Outstanding adsorption performance of high aspect ratio and super-hydrophobic carbon nanotubes for oil removal.

Oil removal from water is a highly important area due to the large production rate of emulsified oil in water, which is considered one of the major pollutants, having a negative effect on human health, environment and wildlife. In this study, we have reported the application of high quality carbon nanotube bundles produced by an injected vertical chemical vapor deposition (IV-CVD) reactor for oil removal. High quality, bundles, super hydrophobic, and high aspect ratio carbon nanotubes were produced. The average diameters of the produced CNTs ranged from 20 to 50 nm while their lengths ranged from 300 to 500 µm. Two types of CNTs namely, P-CNTs and C-CNTs, (Produced CNTs from the IV-CVD reactor and commercial CNTs) were used for oil removal from water. For the first time, thermogravimetric analysis (TGA) was conducted to measure maximum oil uptake using CNT and it was found that P-CNT can take oil up to 17 times their weight. The effect of adsorbent dosage, contact time, and agitation speed were examined on the oil spill clean-up efficiency using batch sorption experiments. Higher efficiency with almost 97% removal was achieved using P-CNTs compared to 87% removal using C-CNTs.

Combating oil spill problem using plastic waste.

Thermoplastic polymers (such as polypropylene, polyethylene, polyethylene terephthalate (PET) and high density polyethylene (HDPE)) constitute 5-15% of municipal solid waste produced across the world. A huge quantity of plastic waste is disposed of each year and is mostly either discarded in landfills or incinerated. On the other hand, the usage of synthetic polymers as oil sorbents, in particular, polyolefins, including polypropylene (PP), and polyethylene (PE) are the most commonly used oil sorbent materials mainly due to their low cost. However, they possess relatively low oil absorption capacities. In this work, we provide an innovative way to produce a value-added product such as oil-sorbent film with high practical oil uptake values in terms of g/g from waste HDPE bottles for rapid oil spill remedy.

Removal of cadmium ions from wastewater using innovative electronic waste-derived material.

Cadmium is a highly toxic heavy metal even at a trace level. In this study, a novel material derived from waste PCBs has been applied as an adsorbent to remove cadmium ions from aqueous solutions. The effects of various factors including contact time, initial cadmium ion concentration, pH and adsorbent dosage have been evaluated. The maximum uptake capacity of the newly derived material for cadmium ions has reached 2.1mmol/g at an initial pH 4. This value shows that this material can effectively remove cadmium ions from effluent. The equilibrium isotherm has been analyzed using several isotherm equations and is best described by the Redlich-Peterson model. Furthermore, different commercial adsorbent resins have been studied for comparison purposes. The results further confirm that this activated material is highly competitive with its commercial counterparts.

Sorption of cadmium, copper, and zinc ions onto bone char using Crank diffusion model.

The rates of adsorption of cadmium, copper and zinc ions onto bone char have been studied in three single component systems using an agitated batch adsorber. The effects of initial metal ion solution concentration and bone char mass have been studied. The capacities of the three metals on bone char are 0.477, 0.709 and 0.505 mmol g(-1) for cadmium, copper and zinc respectively which are much higher than most other adsorbents reported in the literature for these three metals. In order to model the experimental concentration decay curves, a film-surface diffusion equation proposed by has been solved. The model results correlate the experimental better than a previously applied film-pore diffusion model. However, the results indicate that the surface diffusion coefficient was a variable function of initial metal ion concentration. The surface diffusivities vary from 3.00 x 10(-9) to 8.80 x 10(-9) cm(2)s(-1), 2.11 x 10(-9) cm(2)s(-1) to 5.4 x 10(-9) cm(2)s(-1) and 3.10 x 10(-9) to 8.49 x 10(-9) cm(2)s(-1) for cadmium, copper and zinc respectively, for metal ion solution concentrations of 2.10-5.40 mmol dm(-3).

Combining bupropion SR with venlafaxine, paroxetine, or fluoxetine: a preliminary report on pharmacokinetic, therapeutic, and sexual dysfunction effects.

BACKGROUND: This study was designed to evaluate the effect of combining bupropion sustained release (SR) with venlafaxine, paroxetine, or fluoxetine in patients who reported unacceptable sexual dysfunction when treated with monotherapy with the latter 3 agents. METHOD: Following a minimum of 6 weeks of antidepressant treatment with a selective serotonin reuptake inhibitor (SSRI) or venlafaxine (a serotonin-norepinephrine reuptake inhibitor), eligible subjects received a further 8 weeks of monitored combination therapy with bupropion SR at a dose of 150 mg/day with no alterations to index antidepressant dosing. RESULTS: There was a clinically significant benefit in 14 (78%) of 18 partial responders or nonresponders, and 33% (N = 6) achieved a full response (chi2= 8.06, df = 2, p = .017). Sexual dysfunction, particularly a decrease in orgasmic delay, was also significantly improved with combination therapy (men: paired t = -2.1, df = 6, p = .08; women: paired t = -3.0, df = 7, p = .02). Plasma monitoring of drugs and their metabolites revealed a statistically significant increase in venlafaxine levels (F = 6.89, df = 4,24; p = .001) accompanied by a decrease in O-desmethylvenlafaxine (F = 14.26; df = 4,24; p < .0005) during combined treatment with bupropion SR. There were no statistically significant changes in plasma levels of SSRIs (paroxetine and fluoxetine) during the trial. CONCLUSION: Bupropion had an effect on the pharmacokinetics of venlafaxine but not those of the SSRIs. Further investigation of combination treatments under randomized, double-blind conditions is recommended.